Professional Documents
Culture Documents
WWW.CONCRETE.ORG/ACI318 1
Learning Objectives
WWW.CONCRETE.ORG/ACI318 2
Learning Objectives
WWW.CONCRETE.ORG/ACI318 3
Speakers
WWW.CONCRETE.ORG/ACI318 4
ACI 318-19
Changes to the Concrete
Design Standard
Introduction
WWW.CONCRETE.ORG/ACI318 5
Today’s Seminar
• Major changes
• Grouped by topic
• Organization • Foundations
• Existing structures • Anchorage to
• Loads & analysis concrete
• Slabs • Seismic
• Post-tensioning
• Precast/Prestressed
• Circular sections
• Walls
WWW.CONCRETE.ORG/ACI318 6
Today’s Seminar
• Major changes
• Grouped by topic
WWW.CONCRETE.ORG/ACI318 7
Today’s Seminar
318M-14 318-19
WWW.CONCRETE.ORG/ACI318 8
Why Do We Change ACI 318?
WWW.CONCRETE.ORG/ACI318 9
Resources
• ACI 318
• Speaker notes
WWW.CONCRETE.ORG/ACI318 10
ACI 318-19
Versions
• English
• Spanish
• In.-lb units
• SI units
WWW.CONCRETE.ORG/ACI318 11
Speaker Notes
Today’s presentation
WWW.CONCRETE.ORG/ACI318 12
ACI Design Handbook
• 15 chapters
• Explanatory text
• Design aids
• 2019 version
expected early next
year
WWW.CONCRETE.ORG/ACI318 13
ACI Design Handbook
WWW.CONCRETE.ORG/ACI318 14
ACI 318 Building Code Portal
WWW.CONCRETE.ORG/ACI318 15
ACI 318-19
Changes to the Concrete
Design Standard
Organization
WWW.CONCRETE.ORG/ACI318 16
Major goals of ACI 318 organization
• Ease of use
• Find the information you need quickly
– Consistent organization
– Organized in the order of design
• Increase certainty that a design fully meets
the Code
– A chapter for each member type
– All member design provisions in one chapter
WWW.CONCRETE.ORG/ACI318 17
Navigation
10 Parts
• General
WWW.CONCRETE.ORG/ACI318 18
Navigation
10 Parts
• General
• Loads & Analysis
WWW.CONCRETE.ORG/ACI318 19
ACI 318 Style
WWW.CONCRETE.ORG/ACI318 20
Navigation
10 Parts
• General • Materials &
• Loads & Analysis Durability
• Members • Strength &
• Joints/Connections/ Serviceability
Anchors • Reinforcement
• Seismic • Construction
• Evaluation
WWW.CONCRETE.ORG/ACI318 21
Part 1: General
• 1: General
WWW.CONCRETE.ORG/ACI318 22
Part 1: General
• 3: Referenced Standards
Materials
Design
Inspection loads
Precast/
Load paths
Prestressed
• 4: Structural System
Requirements Fire Structural
Safety analysis
Structural Strength
integrity
Serviceability
Sustainability
Durability
WWW.CONCRETE.ORG/ACI318 23
Part 2: Loads & Analysis
• 5: Loads
• 6: Structural Analysis
– Simplified, first-order, second-order
– Linear, nonlinear
– Slenderness
– Materials and section properties
WWW.CONCRETE.ORG/ACI318 24
Part 3: Members
WWW.CONCRETE.ORG/ACI318 25
Typical member chapter sections
• X.1 Scope
• X.2 General
• X.3 Design Limits
• X.4 Required Strength
• X.5 Design Strength
• X.6 Reinforcement Limits
• X.7 Reinforcement Detailing
• X.? ?
WWW.CONCRETE.ORG/ACI318 26
ACI 318-19
Organization
Anchorage, Ch. 9
12
Flexure, Ch. 9
10
Δ
Shear, Ch. 9
11
Deflection, Ch. 9
WWW.CONCRETE.ORG/ACI318 27
Part 4: Joints / Connections / Anchors
• 16: Connections
between members
• 17: Anchoring to
concrete
WWW.CONCRETE.ORG/ACI318 28
Part 5: Seismic
• 18: Earthquake
Resistant Structures
WWW.CONCRETE.ORG/ACI318 29
Part 6: Materials & Durability
(Credit: PCA)
• 20: Steel Reinforcement Properties,
Durability, and Embedments
WWW.CONCRETE.ORG/ACI318 30
Part 7: Strength & Serviceability
WWW.CONCRETE.ORG/ACI318 31
Organization
Member Chapter Toolbox Chapter
9.5 — Design strength
9.5.2 — Moment
9.5.2.1 — If Pu < 0.10f’cAg, 22.3 —Flexural strength…
Mn shall be calculated in
accordance with 22.3. 22.3.3.4 …
22.4.3.1 …
WWW.CONCRETE.ORG/ACI318 32
Part 7: Strength & Serviceability
• 24: Serviceability
Δ ≤ l/360, 𝐼𝑒𝑓𝑓
WWW.CONCRETE.ORG/ACI318 33
Part 8: Reinforcement
Lap ≥ 150 mm
WWW.CONCRETE.ORG/ACI318 34
Part 9: Construction
WWW.CONCRETE.ORG/ACI318 35
Part 10: Evaluation
WWW.CONCRETE.ORG/ACI318 36
Benefits of ACI 318 organization
WWW.CONCRETE.ORG/ACI318 37
1.4—Applicability
WWW.CONCRETE.ORG/ACI318 38
Concrete designs governed by other ACI codes
369 – Seismic Retrofit 376 – RLG Containment 437 – Strength Evaluation 562 - Repair
WWW.CONCRETE.ORG/ACI318 39
Design recommendations provided in guides
WWW.CONCRETE.ORG/ACI318 40
ACI 318-19
Changes to the Concrete
Design Standard
Existing Structures
WWW.CONCRETE.ORG/ACI318 41
1.4.2—Repair
WWW.CONCRETE.ORG/ACI318 42
Chapter 27 – Strength Evaluation of Existing
Structures
Applies when strength is in doubt
• Well understood – analytical evaluation
• Not well understood – load test
– Monotonic procedure, ACI 318
– Cyclic procedure, ACI 437.2
WWW.CONCRETE.ORG/ACI318 43
27.4.6.2—Total test load, Tt
Greatest of:
(a) Tt = 1.15D + 1.5L + 0.4(Lr or S or R)
→Tt = 1.0Dw + 1.1Ds + 1.6L + 0.5(Lr or S or R)
(b) Tt = 1.15D + 0.9L + 1.5(Lr or S or R)
→ Tt = 1.0Dw + 1.1Ds + 1.0L + 1.6(Lr or S or R)
(c) Tt = 1.3D
→Tt = 1.3(Dw + Ds)
WWW.CONCRETE.ORG/ACI318 44
ACI 318-19
Changes to the Concrete
Design Standard
High-Strength
Reinforcement
WWW.CONCRETE.ORG/ACI318 45
180 1200
A1035, Grade 100 (690)
160
1000
Stress, MPa
140
Stress, ksi
WWW.CONCRETE.ORG/ACI318 48
Bar instability and low-cycle fatigue
WWW.CONCRETE.ORG/ACI318 49
Ch. 20 –Seismic Requirements for A615 Gr. 420
WWW.CONCRETE.ORG/ACI318 50
Ch. 20 – Seismic Requirements for A615
WWW.CONCRETE.ORG/ACI318 51
Table 20.2.2.4(a)
• Main changes
– Gr. 550
– Gr. 690
– Footnotes
– Clarifications
WWW.CONCRETE.ORG/ACI318 52
Ch. 20 – Steel Reinforcement Properties
WWW.CONCRETE.ORG/ACI318 53
Ch. 20 – Steel Reinforcement Properties
WWW.CONCRETE.ORG/ACI318 55
Ch. 20 – Steel Reinforcement Properties
WWW.CONCRETE.ORG/ACI318 56
High-strength reinforcement and design
WWW.CONCRETE.ORG/ACI318 57
Design limits
ACI 318M-14ACI 318-19
et ≥ 0.005
et ≥ (ety + 0.003)
WWW.CONCRETE.ORG/ACI318 58
Design limits
ACI 318-19
et ≥ (ety + 0.003)
fy
e ty =
Es
WWW.CONCRETE.ORG/ACI318 59
Design limits
ACI 318-14
WWW.CONCRETE.ORG/ACI318 60
Design limits
ACI 318-19
WWW.CONCRETE.ORG/ACI318 61
Design limits
fy
e ty =
Es
WWW.CONCRETE.ORG/ACI318 62
Design limits
GR 420 GR 690
As,tcl = 3866 mm2 As,tcl = 1987 mm2
Mn,tcl = 738 kNm Mn,tcl = 649 kNm
WWW.CONCRETE.ORG/ACI318 63
ACI 318-19
Cambios en la norma de diseño
del concreto estructural
Cargas y Análisis
WWW.CONCRETE.ORG/ACI318 64
Capítulo 4: Requisitos para Sistemas Estructurales
Materiales
• Propósito Inspección
Cargas de
diseño
4.2
– La estructura como 4.13 4.3
un todo Resistencia Trayectoria
al fuego de cargas
– Mapa de ruta del 4.11 4.4
proceso de diseño
• Temario Integridad Análisis
estructural estructural
4.10 4.5
– Alcance
– 14 subsecciones Sostenibilidad Resistencia
4.9 4.6
Durabilidad Funcionamiento
4.8 4.7
WWW.CONCRETE.ORG/ACI318 65
4.2 Materiales
• Capítulo 19 - Concreto: requisitos de diseño y
funcionamiento
– fc’ (máximo y mínimo)
– Ec
– Modulo de ruptura fr
– Concreto liviano
– Categorías y Clases de exposición
– Propiedades de mortero de inyección
• Capítulo 20 – Propiedades del acero de refuerzo,
durabilidad y embebidos
– fy, Es
– Barras de refuerzo, aceros de preesfuerzo, barras con
cabeza, embebidos, …
– Durabilidad (recubrimiento de concreto, recubrimientos)
WWW.CONCRETE.ORG/ACI318 66
4.3 Cargas de diseño
WWW.CONCRETE.ORG/ACI318 67
4.4 Sistemas estructurales y trayectorias de
cargas
• Sistemas Losas de pisos Vigas y
estructurales y techos viguetas
Cap. 9
compuestos por Cap. 7 y 8
miembros y
conexiones
Muros
• Trayectorias de Columnas
Cap. 10 Cap. 11
cargas definidas
(gravedad y
lateral)
• Mapa de ruta de Diafragmas
Cap.12
Cimentaciones
Cap. 13
los capítulos de los
miembros
Conexiones
y anclaje
WWW.CONCRETE.ORG/ACI318 68
4.4 Sistemas estructurales y trayectoria de cargas
• Requisitos sísmicos
– Diseñador asigna la Categoría de Diseño Sísmico
• Categoría A (menor riesgo) a Categoria F (mayor
riesgo)
– Categoría A
• No hay requisitos especiales
• Diseño de acuerdo con los Capítulos 1-17, 19-26
• Pórticos resistentes a momento y muros Ordinarios
• Primordialmente comportamiento elástico
WWW.CONCRETE.ORG/ACI318 69
4.4 Sistemas estructurales y trayectoria de cargas
• Requisitos sísmicos
– Categorías B – F
• Requisitos → Capítulo 18
• Categoría B – pórticos y muros ordinarios
• Categoría C – Pórticos intermedios, muros ordinarios
• Categorías D, E, F – Pórticos y muros especiales
– Miembros que no son parte del sistema del
sistema de resistencia ante cargas laterales
• Requisitos de acuerdo con la Categoría de Diseño
Sísmico
WWW.CONCRETE.ORG/ACI318 70
Organización del capítulo 18
WWW.CONCRETE.ORG/ACI318 71
4.4 Sistemas estructurales y trayectoria de cargas
• Diafragmas
– Fuerzas de transferencia
– Dar apoyo lateral
WWW.CONCRETE.ORG/ACI318 72
4.5 Análisis estructural
• Compatibilidad de deformaciones
• Equilibrio de fuerzas
• Métodos aceptables de análisis → Capítulo 6
4.6 Resistencia
WWW.CONCRETE.ORG/ACI318 73
4.7 Funcionamiento
4.8 Durabilidad
• La durabilidad del concreto depende de la
exposición
– Categoría de exposición → 19.3.1
– Requisitos para las mezclas →19.3.2
• Protección de la corrosión → 20.6
WWW.CONCRETE.ORG/ACI318 74
4.9 Sostenibilidad
WWW.CONCRETE.ORG/ACI318 75
4.11 Resistencia al fuego
WWW.CONCRETE.ORG/ACI318 76
4.13 Construcción e inspección
WWW.CONCRETE.ORG/ACI318 77
Capítulo 5 - Cargas
• Cargas→ Reglamento general de
construcción
– Usualmente ASCE 7-10
– Si es considerablemente diferente de ASCE 7,
puede requerirse ajustar los requisitos de ACI 318
apropiadamente
• Viento
– Los factores basados en viento al nivel de
resistencia
– Multiplicar por 1.6 para viento al nivel de servicio
WWW.CONCRETE.ORG/ACI318 78
Capítulo 5 - Cargas
• Combinaciones
– Básicas → Tabla 5.3.1
– Excepciones y adiciones → Sección 5.3
WWW.CONCRETE.ORG/ACI318 79
Capítulo 5 – Cargas
• Categorías de diseño
sísmico (CDS)
– CDS → Reglamento
general de construcción
– Adoptado del ASCE 7-10
– Correlaciones Tabla
R5.2.2
WWW.CONCRETE.ORG/ACI318 80
Fuerzas de viento (R5.3.5)
• Comentario añadido
– ASCE 7-05
• Viento = viento para nivel de servicio
• Utilizar un factor de carga de 1.6
WWW.CONCRETE.ORG/ACI318 81
Capítulo 6 – Análisis estructural
• Suposiciones para definir el modelo
– Ancho del ala
– Momento de inercia
• Disposición de la carga viva
• Métodos de análisis permitidos
– Métodos simplificados
– Elástico de primer orden
– Elástico o inelástico de segundo orden
– Análisis utilizando elementos finitos
WWW.CONCRETE.ORG/ACI318 83
6.5 Método simplificado
• Vigas y losas en una dirección
– Mu → Tabla 6.5.2
– Vu → Tabla 6.5.4
– Restricciones
• Miembros prismático
• Cargas distribuidas
• L (viva) ≤ 3D (muerta)
• ≥ 2 vanos
• L1 < 1.2 L2
• No hay redistribución
WWW.CONCRETE.ORG/ACI318 84
6.6 Análisis de primer orden
• Cumple equilibrio para la estructura no
deformada
– Propiedades lineales de los materiales
– Solución lineal
– Superposición de cargas
– Efectos de esbeltez (si se requieren)
• Magnificador de momentos (aproximado)
– Cálculos manuales
– Momento de inercia efectivo
• Carga mayoradas → Tabla 6.6.3.1.1(a)
• Cargas de servicio → 1.4 x Tabla 6.6.3.1.1(a)
WWW.CONCRETE.ORG/ACI318 85
6.7 Análisis elástico de segundo orden
• Cumple equilibrio para la estructura
deformada
– Propiedades lineales de los materiales
– Solución no lineal
– No hay superposición de cargas
– Efectos de esbeltez
• No hay magnificación de momentos para el
desplazamiento relativo
• Se debe considerar la deflexión entre los extremos →
6.6.4.5
– Cálculos utilizando computador
– Momento de inercia efectivo
• Carga mayoradas → Tabla 6.6.3.1.1(a)
• Se permite utilizar I = 0.5 I g para todos los miembros o un
análisis mas detallado.
WWW.CONCRETE.ORG/ACI318 86
6.8 Análisis inelástico de segundo orden
• Consideraciones
– Materiales no lineales
– Se debe cumplir equilibrio en la configuración
deformada.
– No se permite redistribución de los momentos
calculados por medio de un análisis inelástico.
WWW.CONCRETE.ORG/ACI318 87
6.9 Aceptación de análisis utilizando
elementos finitos
• Método muy usado
• Apropiado para lo que se pretende
– Tipos de elementos
– Disposición y tamaño de la red
– Tipo de análisis (lineal, no lineal, dinámico)
– Resultados apropiados
• Dimensiones de los elementos dentro del
10% del tamaño final
• No se permite redistribución ni
superposición con análisis inelástico
WWW.CONCRETE.ORG/ACI318 88
ACI 318-19
Cambios en la norma de diseño
del concreto estructural
WWW.CONCRETE.ORG/ACI318 105
Refuerzo para integridad estructural
WWW.CONCRETE.ORG/ACI318 106
Refuerzo de retracción y temperatura
WWW.CONCRETE.ORG/ACI318 111
ACI 318-19
Cambios en la norma de diseño
del concreto estructural
WWW.CONCRETE.ORG/ACI318 112
Método de diseño directo y Método del
pórtico equivalente
– Ha sido removido: El método de diseño directo (8.10)
y el método del pórtico equivalente (8.11)
– Requisitos en 318-14
WWW.CONCRETE.ORG/ACI318 113
Cabezas de cortante
• Requisitos para
cabezas de cortante
en 318-14 han sido
removidos
– 8.4.4.1.3 Las losas
reforzadas con cabezas
de cortante se deben
evaluar para cortante
en dos direcciones en
las secciones críticas de
acuerdo con 22.6.9.8.
WWW.CONCRETE.ORG/ACI318 114
Abertura en sistemas de losa sin vigas
ACI 318-14: 8.5.4.2(d)
• dentro de las franjas de columna o
a una distancia menor a 10h de
una carga concentrada o zona de
reacción, deben cumplir con
– 22.6.4.3 para losas sin cabeza de
cortante
– o 22.6.9.9 para losas con cabeza de
cortante
– Fig. R22.6.4.3
WWW.CONCRETE.ORG/ACI318 116
Refuerzo mínimo a flexión en losas no
preesforzadas — Dos direcciones
8.6.1.1
• 318-14: As,min según la Tabla 8.6.1.1.
WWW.CONCRETE.ORG/ACI318 117
Extensiones de refuerzo para losas sin vigas
WWW.CONCRETE.ORG/ACI318 118
Falla de cortante por punzonamiento —
Losa de podio Acero superior (34 barras No. 9)
50% to 0.2L (2400 mm)
600 mm
Columna 300x1100
(no se muestra el refuerzo para mayor claridad)
WWW.CONCRETE.ORG/ACI318 119
Extensiones de refuerzo para losas en dos
direcciones sin vigas
ACI 318-19: 8.7.4.1.3 d
— Barras superiores
de franja de columna
• Extienda al menos
0.3ℓn pero, no d
menos de 5d
WWW.CONCRETE.ORG/ACI318 120
Extensiones de refuerzo para losas en dos
direcciones sin vigas
WWW.CONCRETE.ORG/ACI318 121
ACI 318-19
Cambios en la norma de diseño
del concreto estructural
Postensado
WWW.CONCRETE.ORG/ACI318 122
Losas residenciales P-T (1.4.6)
WWW.CONCRETE.ORG/ACI318 123
Losas residenciales P-T (1.4.6)
WWW.CONCRETE.ORG/ACI318 124
Máx. Espaciamiento del refuerzo corrugado
(7.7.2.3)
WWW.CONCRETE.ORG/ACI318 125
Max. Espaciamiento del refuerzo corrugado
(7.7.2.3)
s ≤ 3h y 450 mm
Sección de la losa
WWW.CONCRETE.ORG/ACI318 126
Refuerzo de la zona de anclaje P-T (25.9.4.4.6)
Horquillas
Barras de respaldo
Barras de anclaje
WWW.CONCRETE.ORG/ACI318 127
WWW.CONCRETE.ORG/ACI318 128
Refuerzo de la zona de anclaje P-T
(25.9.4.4.6)
• Losas delgadas ≤ 200 mm → Las barras de
anclaje sirven como barras de respaldo
WWW.CONCRETE.ORG/ACI318 133
ACI 318-19
Cambios en la norma de diseño
del concreto estructural
Prefabricado/Preesforzado
WWW.CONCRETE.ORG/ACI318 134
Concreto prefabricado / Concreto preesforzado
WWW.CONCRETE.ORG/ACI318 135
Confinamiento
125 mm
Dos N°. 13 o
Tres barras N°. 10
WWW.CONCRETE.ORG/ACI318 136
Confinamiento
Dos N° 13 o
Tres barras N° 10
WWW.CONCRETE.ORG/ACI318 137
Cambios volumétricos en conexiones
prefabricadas
• Cambios volumétricos
– Asentamiento por flujo plástico
– Retracción
– Temperatura
• Puede inducir reacciones de conexión si se
restringe
WWW.CONCRETE.ORG/ACI318 138
Cambio de volumen en conexiones
prefabricadas
• Magnitud de la carga?
• ¿Factor de la carga?
• Orientación pasada
para cartelas y
ménsulas
– Use Nuc ≥ 0.2Vu como
fuerza de retención
– Utilizar un factor de carga
de 1.6
• El enfoque a menudo
consistía en diseñar
alrededor de fuerzas
WWW.CONCRETE.ORG/ACI318 139
Cambio de volumen y conexiones
318-19 cambios (16.2.2.3)
• Nuc = fuerza de contención
mayorada, deberá ser (a) o (b)
– (a) fuerza de retención x factor LL
(sin almohadilla de apoyo)
– (b) 1.6 x 0.2 (carga vertical sostenida
no mayorada) para conexiones en
almohadillas de apoyo
• Nuc,max ≤ capacidad de
conexión x factor LL
• Nuc,max ≤ 1.6 x μ x (carga vertical
sostenida no mayorada) si se
conoce μ, (Véase 16.2.2.4)
WWW.CONCRETE.ORG/ACI318 140
Cartelas y ménsulas
• 26.6.4.1(a) Detalles para la soldadura de las barras
de anclaje en la cara frontal de las cartelas o
ménsulas diseñados por el profesional facultado
para diseñar de acuerdo con 16.5.6.3(a).
WWW.CONCRETE.ORG/ACI318 142
Factor de reducción de resistencia
Cercano al final
del miembro
prefabricado
• Similar para
torones
despegados
WWW.CONCRETE.ORG/ACI318 143
ACI 318-19
Cambios en la norma de diseño
del concreto estructural
Secciones circulares
WWW.CONCRETE.ORG/ACI318 144
Definiciones de variables (22.5)
d?
abertura
ρw ?
bw ?
WWW.CONCRETE.ORG/ACI318 145
Definiciones de variables (22.5)
• 22.5.2.2 — cálculo de Vc y Vs
– d = 0.8 x diámetro
– bw = diámetro (círculos sólidos)
– bw = 2 x espesor del muro (círculos huecos)
t
d = 0.8D
abertura
ρw = As/bwd
bw = D bw = 2t
WWW.CONCRETE.ORG/ACI318 146
Definiciones de variables (22.5)
(2/3)D
As
WWW.CONCRETE.ORG/ACI318 147
Torsión para secciones circulares (R22.7.6.1.1)
• ¿Se aplican las ecuaciones de torsión de ACI
318 a las secciones transversales circulares?
• Las ecuaciones del reglamento se basan en la
teoría del tubo delgado
• Ejemplos añadidos a la figura
WWW.CONCRETE.ORG/ACI318 148
Juntas de Columna
Circular
• Basado en una columna
cuadrada equivalente
– Aj para la resistencia a h = 0.89D
cortante de la junta (15.4.2)
– Anchura de las vigas
transversales necesaria para
que el nudo se considere
confinado (15.2.8)
– Ancho de columna ≥ 20 db
para pórticos especiales
resistentes a momentos
(18.8.2.3)
WWW.CONCRETE.ORG/ACI318 149
ACI 318-19
Cambios en la norma de diseño
del concreto estructural
Muros
WWW.CONCRETE.ORG/ACI318 150
Alcance de los muros
• Cambio de alcance
11.1.4- El diseño de los muros de contención en
voladizo debe estar de acuerdo con el Capítulo 13
(Cimentaciones)
WWW.CONCRETE.ORG/ACI318 151
Alcance de los muros
• Alcance adicional
11.1.6- Muros CES con encofrados aislantes serán
permitidos a usarse en edificios de uno o dos pisos de
acuerdo a este reglamento
• Diseño de acuerdo al Capítulo 11
• Orientación — ACI 560R y PCA 100-2017
• Problemas de construcción únicos
• 318S-14
• ½ a 2/3 del refuerzo es colocado cerca de
la cara exterior
• El resto del refuerzo es colocado cerca de
la cara interior
WWW.CONCRETE.ORG/ACI318 153
14.6 Concreto simple
En ventanas, aberturas de puertas, y en
aberturas de tamaño similar
• Por lo menos dos barras n.º 16 (similares a
muros 11.7.5.1)
• Extienda 600 mm más allá o hasta
desarrollar fy
2 — barras
n.º 16
≥ 600 mm
WWW.CONCRETE.ORG/ACI318 154
ACI 318-19
Cambios en la norma de diseño
del concreto estructural
Cimentaciones
WWW.CONCRETE.ORG/ACI318 155
Cap. 13 — Cimentaciones — cambios
significativos
• Requisitos de diseño añadidos
– Muros de contención en voladizo
• Otros
– Resistencias mínimas del concreto para
cimentaciones superficiales y profundas
– Recubrimiento
WWW.CONCRETE.ORG/ACI318 156
Cimentaciones y 318
• ACI 318-71 (ACI 318S-05)
a ACI 318S-08 (Capítulo
15)
• Zapatas superficiales,
cabezales de pilotes
WWW.CONCRETE.ORG/ACI318 157
Cimentaciones y 318
• ACI 318-71 (ACI 318S-05) a
ACI 318S-08 (Capítulo 15)
• Zapatas superficiales,
cabezales de pilotes
WWW.CONCRETE.ORG/ACI318 158
Muros de contención en voladizo
Es una
losa
Es un
(2019)
muro
(2014)
WWW.CONCRETE.ORG/ACI318 159
13.3.6.1 — El alma de un muro en voladizo
• Debe diseñarse como una losa
de una dirección (Cap. 7)
WWW.CONCRETE.ORG/ACI318 160
13.3.6.2 — El alma de un muro en voladizo con
contrafuerte
• Debe diseñarse como una losa en dos direcciones (Cap. 8)
WWW.CONCRETE.ORG/ACI318 161
Espaciamiento máximo entre barras en el
alma del muro
Muro Losa
Diseño
Diseño como
Refuerzo Espaciamiento Espaciamiento
como losa de
del alma del máximo entre máximo entre
muro una
muro barras (2014) barras (2019)
(2014) dirección
Barras
(2019) longitudinales
El menor de:
Longit.
s Barras
(Muro) o 3h, o 7.7.2.2 transversales
11.7.2.1
Flexión 450 mm (24.3)
(Losa)
Transv.
3h, o 5h, o
(Pared) o S 11.7.3.1 7.7.6.2.1
450 mm 450 mm
& T (Losa)
WWW.CONCRETE.ORG/ACI318 162
Refuerzo mínimo en el alma del muro
ACI 318S-14 ACI 318-19
Diseño
Diseño como Refuerzo mínimo como
Refuerzo mínimo, ρ
muro As,min losa en una
dirección
≤ n.º 16
ρℓ = 0.0012 As,min = 0.0018 Ag
11.6.1 7.6.1.1
> n.º 16
ρℓ = 0.0015
≤ n.º 16
ρt = 0.0020 AS+T = 0.0018 Ag 7.6.4.1
11.6.2
> n.º 16 (24.4)
ρt = 0.0025
WWW.CONCRETE.ORG/ACI318 163
1.4.7 —Cambios en el alcance — cimentaciones
profundas
• Alcance: Este reglamento no gobierna el diseño e
instalación de porciones de pilotes de concreto, pilas
excavadas y cajones de cimentación enterrados en
el suelo, excepto como se estipula en (a) a (c)
• (a) Para porciones en el aire o en el agua, o en el suelo
incapaces de dar soporte lateral adecuado para evitar el
pandeo a lo largo de toda su longitud
WWW.CONCRETE.ORG/ACI318 164
Cimentaciones profundas (13.4)
• 13.4.1 Generalidades
• 13.4.2 Resistencia axial permisible
• 13.4.3 Diseño por resistencia
• 13.4.4 Cimentaciones profundas construidas en sitio
• 13.4.5 Pilotes de concreto prefabricado
• 13.4.6 Cabezales de pilotes
WWW.CONCRETE.ORG/ACI318 165
Cimentaciones profundas — combine IBC &
ASCE 7
• ACI 318 – 19 –
CIB
– IBC 2015 combinado, ASCE 7-10 ASCE 7
2015
WWW.CONCRETE.ORG/ACI318 166
Pre- ACI 318-19 — diseño de cimentaciones
profundas
• ACI 543 — Pilotes (diam. < 750
mm)
• ACI 336.3 — Diseño de pilares
excavados (diam. ≥ 750 mm)
No son documentos en
lenguaje de reglamento
También se utilizan los requisitos
de zapatas profundas de:
IBC y ASCE/SEI 7
WWW.CONCRETE.ORG/ACI318 167
• Diseño de la resistencia axial de
los miembros de acuerdo con
dos métodos:
– Diseño de resistencia axial permisible
(13.4.2)
– Diseño por resistencia (13.4.3)
WWW.CONCRETE.ORG/ACI318 169
13.4.2 diseño de cimentación profunda
WWW.CONCRETE.ORG/ACI318 170
Confinamiento de la camisa metálica (13.4.2.3):
Diámetro ≤ 400 mm
• no es usada para resistir cargas
axiales
• punta sellada hincada con mandril
• sin costura o soldada sin costura
WWW.CONCRETE.ORG/ACI318 171
Cimentaciones profundas — diseño por
resistencia (13.4.3)
Pu
• El método puede ser utilizado en Mu ≥ 0
cualquier momento
• Se debe utilizar el método cuando el
pilote no cumple los criterios para el
diseño de la resistencia axial permisible
– El suelo no proporciona apoyo lateral
– El momento no es insignificante
WWW.CONCRETE.ORG/ACI318 172
Diseño por resistencia (13.4.3) — fuerza axial, sin
momento
Resistencia nominal a la compresión axial; Pn Pu Mu= 0
𝝓 Pn,máx. ≥ Pu
Resistencia axial máxima
— Para miembros de cimentaciones
profundas con estribos que cumplen con
el Capítulo 13 (nuevo en la Tabla 22.4.2.1)
Pn,max. = 0.80 Po
Dónde:
Po = fuerza axial nominal con
excentricidad cero
Po = 0.85f’c(Ag – Ast) + fyAst
WWW.CONCRETE.ORG/ACI318 173
Diseño por resistencia (13.4.3) — fuerza axial, sin
momento
• Factor de reducción — Tabla 13.4.3.2 Pu Mu= 0
0.55 a
0.70
WWW.CONCRETE.ORG/ACI318 174
Cimentaciones profundas
13.4.4.1 Cimentaciones
profundas CES que estén
sometidas a (a) Confinado para
levantamiento o (b) Mu > ductilidad
o tubo de acero
flexión
Reforzado para la
tracción
Sin refuerzo
WWW.CONCRETE.ORG/ACI318 175
Tabla 19.2.1.1 — Limites para f'c
WWW.CONCRETE.ORG/ACI318 176
Recubrimiento de concreto — cimentaciones
profundas Tubo de
acero
Tabla 20.5.1.3.4
75 mm 40 mm
WWW.CONCRETE.ORG/ACI318 179
Chapter 17 – Anchoring to Concrete
• Reorganized
• New content/design
information
– Screw anchors
– Caution about using
reinforcement for
anchorage
– Shear lugs
WWW.CONCRETE.ORG/ACI318 180
Sections
WWW.CONCRETE.ORG/ACI318 181
Ch. 17 – Anchoring to Concrete
Scope
• Headed studs and
headed bolts
• Hooked bolts
• Post-installed
undercut anchors
• Post-installed
expansion anchors
• Post-installed
adhesive anchors
WWW.CONCRETE.ORG/ACI318 182
Screw Anchors (17.3.4)
– 17.6.2 in tension
– 17.7.2 in shear
WWW.CONCRETE.ORG/ACI318 184
Minimum Spacing (17.9.2a)
WWW.CONCRETE.ORG/ACI318 185
17.1.6 – Reinforcement used as anchorage
ℓd
anchorage
plate
photo compliments of P. Carrato
WWW.CONCRETE.ORG/ACI318 186
17.1.6 – Reinforcement used as anchorage
• Check development
length per chapter 25,
and
• Check breakout
strength per chapter 17.
– Straight bars behave like
adhesive anchors
– Hooked and headed bars
behave like headed
anchors
– Anchor reinforcement
may be an alternative
WWW.CONCRETE.ORG/ACI318 187
Shear Lugs (17.11.1)
WWW.CONCRETE.ORG/ACI318 189
Shear Lug Detailing (17.11.1.2)
WWW.CONCRETE.ORG/ACI318 190
Stiffeners
T/Conc
Stiffener hsl
0.5hsl
Shear lug
WWW.CONCRETE.ORG/ACI318 191
Shear Lugs (17.11.1)
• Minimum four
anchors
• Anchors:
– If not welded, then
design assuming no
anchor shear.
– If welded, then
design anchors to
resist portion of shear
(in combination with
other actions)
WWW.CONCRETE.ORG/ACI318 192
Shear Lug Detailing (17.11.1.1.8)
WWW.CONCRETE.ORG/ACI318 193
Shear Lug Overturning (17.11.1.1.9)
hsl
hef
tsl
Csl
WWW.CONCRETE.ORG/ACI318 194
Bearing (17.11.2)
• f Vbrg,sl ≥ Vu
• Where f = 0.65
WWW.CONCRETE.ORG/ACI318 195
Bearing Strength
Vbrg ,sl = 1.7 f Aef ,sl brg ,sl
c
'
Direction of
shear load
Direction of
shear load
WWW.CONCRETE.ORG/ACI318 198
17.11.2.2 – Bearing factor
Tension load
V = 1.7 f A
brg , sl c
'
ef , sl
brg , sl
τ = Vu/(A1 + A2)
A2
A1
WWW.CONCRETE.ORG/ACI318 200
17.11.3 – Concrete breakout strength of
shear lugs
• Where:
WWW.CONCRETE.ORG/ACI318 201
17.11.3.4 – Breakout for Multiple Shear Lugs
WWW.CONCRETE.ORG/ACI318 202
Shear Lug Example
800 mm
LH = ± 40 kN
WH = ±53 kN
200 mm
Pedestal
800 mm
f’c = 31 MPa
WWW.CONCRETE.ORG/ACI318 203
Shear Lug Example
• Can we replace upper ties with shear lug?
– Remove shear from anchor rod design
– May reduce bolt size/length 400
110
– Simplify design
50 typ.
40 mmx 535 mmx 535 mm
steel plate No. 13
75 300
75
660 mm 800
WWW.CONCRETE.ORG/ACI318 204
Size Shear Lug
WWW.CONCRETE.ORG/ACI318 205
Shear Lug Example
400
WWW.CONCRETE.ORG/ACI318 206
Strength Checks
W360
75
75
660 mm
WWW.CONCRETE.ORG/ACI318 207
Bearing Strength Check
V
• Vua,g ≤ f Vbrg,sl (bearing)
– Vua,g = 133 kN 1.7 f’c
– Vbrg,sl = 1.7 f’c Aef,sl Ψbrg,sl
• For tension on attachment, bearing is reduced
– Pu = -516 kN (Max. vertical tension from, 1.2D ± 1.0W)
– Ψbrg,sl = 1+Pu/(nNsa)
– = 1+(-516 kN)/(4 rods(323 kN/rod))= 0.601
– Vbrg,sl = 1.7 (31 MPa)(200 mm)(75 mm)(0.601) = 475 kN
V ca1 = 380 mm
75 mm
572 mm
800 mm 800 mm
WWW.CONCRETE.ORG/ACI318 209
Concrete Breakout Strength Check
AVco
ca1 = 380 mm
1.5 ca1
1.5 ca1
800 mm
WWW.CONCRETE.ORG/ACI318 210
Concrete Breakout Strength Check
ca1 = 380 mm
ca2 = 300 mm
800 mm
WWW.CONCRETE.ORG/ACI318 211
Concrete Breakout Strength Check
– Vb = 3.7λaf’c(ca1)1.5
= 3.7(1)(31 MPa)(380 mm)1.5 = 153 kN
WWW.CONCRETE.ORG/ACI318 212
Concrete Breakout Strength Check
WWW.CONCRETE.ORG/ACI318 213
ACI 318-19
Changes to the Concrete
Design Standard
Seismic Design
Philosophy
WWW.CONCRETE.ORG/ACI318 216
Seismic
WWW.CONCRETE.ORG/ACI318 217
Seismic – Ω, Cd, and R Factors (ASCE 7)
Lateral
seismic
force, V E
𝑉𝑒
Idealized elastic
response of
structure
𝑉𝑒 Fully yielded strength (b) Sequence of plastic hinge
× Ω𝑜
𝑅Τ𝐼𝑒 formation (Degenkolb)
Successive yield
Member hinges
𝑉𝑒 overstrength
of first hinge Design force level
𝑅Τ𝐼𝑒
Δ Cd Δ Lateral drift, D
WWW.CONCRETE.ORG/ACI318 218
Seismic – Parameters
Parameter in ASCE 7-16 Example
Table 12.2-1
Special reinforced
Seismic Force Resisting
concrete shear walls
System
(building frame system)
ASCE 7 Section Where
ASCE 7 Section 14.2
Detailing Requirements Are
“Concrete”
Specified
Response Modification
6
Coefficient, R
Overstrength Factor, Ω0 2.5
Deflection Amplification
5
Factor, Cd
SDC B No limit
Structural System SDC C No limit
Limitations, Including SDC D 160 ft
Structural Height Limits SDC E 160 ft
SDC F 100 ft
WWW.CONCRETE.ORG/ACI318 220
2
Seismic
• Controlled inelastic action is permitted at pre-
determined locations, called plastic hinges
• Typical plastic hinge locations are at the ends
of beams in moment frames, and at the bases
of shear walls
WWW.CONCRETE.ORG/ACI318 221
Seismic
• Prescriptive rules for
detailing of
reinforcement are
enforced, creating
robust plastic hinges
• Plastic hinging
reduces the stiffness
of the structure,
which lengthens the
period; and plastic
hinges dissipate
earthquake energy
WWW.CONCRETE.ORG/ACI318 222
ACI 318-19
Changes to the Concrete
Design Standard
Intermediate and
Special Moment
Frames
WWW.CONCRETE.ORG/ACI318 223
18.6.3.1 and 18.8.2.3—Special moment frame
beams (and joints)
• Longitudinal Reinforcement
hc/20 (Gr 420)
@ interior joints, 𝑑𝑏 ≤
hc/26 (Gr 550)
hb
−
− +
𝑀𝑛2
+
𝑀𝑛1 𝑀𝑛2 ≥
𝑀𝑛1 ≥ 2
2
max 𝑀𝑛 at either joint
𝑀𝑛+ 𝑜𝑟 𝑀𝑛− at any section ≥
4
WWW.CONCRETE.ORG/ACI318 224
18.6.4.4—Special moment frame beams
• Transverse reinforcement
d/4
hc
s≤ 150 mm
6db (Gr 420), 5db (Gr 550)
𝑠 ≤ 𝑑/2 d/4
≤ 50 𝑚𝑚 s≤ 100 mm
hb
WWW.CONCRETE.ORG/ACI318 225
18.7.5.3 and 18.7.5.5—Columns in special
moment frames
WWW.CONCRETE.ORG/ACI318 226
18.7.4.3—Bond splitting failure in columns
Moment
Diagram
Splitting can be
controlled by
ℓu Τ2 restricting the
longitudinal bar
size to meet:
ℓu Τ2 1.25ℓd ≤ ℓu/2
WWW.CONCRETE.ORG/ACI318 227
18.7.3—Columns of SMF
Mnc
Strong Column/Weak Beam
• Flexural strength check, Beam
18.7.3.2 M Mnb
nb
– ∑Mnc ≥ (6/5)∑Mnb,
– Exception, 18.7.3.1 Column
• Ignore check at top story where
𝑷𝒖 ≤ 𝟎. 𝟏𝑨𝒈 𝒇′𝒄 Mnc
WWW.CONCRETE.ORG/ACI318 228
18.8.4 — Special moment frame beam-column
joints ′
𝑉𝑛 = 𝛾 𝑓𝑐 𝐴𝑗 New in ACI 318-19
= 20 = 15 = 15 = 12
= 15 = 12 = 12 =8
Note: Dashed lines show beams either present or absent.
WWW.CONCRETE.ORG/ACI318 229
18.4.3.3—Columns in intermediate moment
frames
• Hoops or spirals required
• First hoop at so/2 from the joint ℓo
face
ℓu /6 clear span
ℓo ≥ [c1, c2]max
450 mm
so ℓ
oo
8db (Gr 420) and 200 mm
so ≤ 6db (Gr 550) and 150 mm
1/2[c1, c2]min
WWW.CONCRETE.ORG/ACI318 230
ACI 318-19
Changes to the Concrete
Design Standard
Special Structural
Walls
WWW.CONCRETE.ORG/ACI318 232
Mu
Ch. 18.10—Special structural wall δu
Pu
Vu
• Cutoff of longitudinal bars
in special boundary
elements
• Reinforcement lap splices
hw
• Reinforcement ratios at Special
ends of walls boundary
element
• Shear demand
• Drift capacity check
• Detailing in special
boundary elements
• Ductile coupled walls ℓw
Shear wall
WWW.CONCRETE.ORG/ACI318 233
18.10.2.3(a)—Longitudinal bar cutoffs
• Previously,
– tension (vertical boundary) reinforcement in
special structural walls to extend 0.8ℓw beyond
the point at which it is no longer required to resist
flexure
• Overly conservative
– This was an approximation of d
– Similar to beams which extend d, 12db and ℓn/16
– These provisions don’t apply well to walls
because of differences in member geometry
and differences in earthquake loadings
WWW.CONCRETE.ORG/ACI318 234
18.10.2.3(a)—Longitudinal bar cutoffs
WWW.CONCRETE.ORG/ACI318 235
18.10.2.3(c)—Longitudinal bar lap splices
• Lap splices not
permitted over hsx
above (6.0 m, max)
and ℓd below
critical sections
WWW.CONCRETE.ORG/ACI318 236
18.10.2.4—Minimum longitudinal reinforcement
ratio at ends of walls
hw/ℓw ≥ 2.0
• Failures due to
longitudinal
reinforcement
fracture in tests and
some earthquakes.
El Faro Building, Viña Gallery Apartment:
del Mar, Chile, 1985 Christchurch, 2011
(Photo Credit: Des Bull)
WWW.CONCRETE.ORG/ACI318 237
18.10.2.4—Minimum longitudinal reinforcement
ratio at ends of walls
New ratio
6 f c'
r=
fy
• Many well
distributed cracks
• Flexure yielding
over height
Rick Henry, U. Aukland
WWW.CONCRETE.ORG/ACI318 238
18.10.2.4—Longitudinal reinforcement ratio
at ends of walls
WWW.CONCRETE.ORG/ACI318 240
18.10.2.4—Minimum longitudinal reinforcement
ratio at ends of walls
Walls or wall piers with hw/ℓw ≥ 2.0 must satisfy:
WWW.CONCRETE.ORG/ACI318 241
18.10.3—Wall shear amplification
WWW.CONCRETE.ORG/ACI318 242
18.10.3—Shear amplification due to overstrength
18.10.3.1.2 – Calculation of Ωv
[1] For the load combination producing the largest value of Ωv.
[2] Unless a more detailed analysis demonstrated a smaller value,
but not less than 1.0.
WWW.CONCRETE.ORG/ACI318 243
18.10.3—Shear amplification due to dynamics
18.10.3.1.3 – Calculation of ωv
where ns ≥ 0.028hwcs
WWW.CONCRETE.ORG/ACI318 244
18.10.3—Wall shear amplification
18.10.3.1 The design shear force Ve shall be
calculated by: Ve = v vVu 3Vu
WWW.CONCRETE.ORG/ACI318 245
18.10.4.4—Clarification of Acv for walls
No changes to wall shear strength
calculation, except clarification of Acv wall = Acw1+Acw2+Acw3
WWW.CONCRETE.ORG/ACI318 248
18.10.6.2—Boundary element confinement
du
(a) Compression zone with special
boundary elements required if:
1.5d u
w
hwcs 600c hwcs
WWW.CONCRETE.ORG/ACI318 250
Wall deformation capacity
𝑙𝑤 𝑐
Stability depends on and .
𝑏 𝑏
ii. b 0.025 wc
WWW.CONCRETE.ORG/ACI318 253
18.10.6.4(f)—Special Boundary Elements
Longitudinal bars supported
by a seismic hook or corner of
a hoop
smax = 300 mm
WWW.CONCRETE.ORG/ACI318 254
18.10.6.5(b)—If the maximum longitudinal r at
the wall boundary exceeds 400/fy
Table 18.10.6.5b—Maximum vertical spacing of transverse reinforcement at wall boundary
Grade of primary Transverse reinforcement Vertical spacing of transverse reinforcement1
flexural reinforcing required
bar (MPa)
Within the greater of ℓw and 6 db
Mu/4Vu above and below Lesser of:
critical sections2 150 mm
420 8 db
Other locations Lesser of:
200 mm
Within the greater of ℓw and 5 db
Mu/4Vu above and below Lesser of:
critical sections2 150 mm
550 6 db
Other locations Lesser of:
150 mm
Within the greater of ℓw and 4db
Mu/4Vu above and below Lesser of:
critical sections2 150 mm
690 6db
Other locations Lesser of:
150 mm
WWW.CONCRETE.ORG/ACI318 257
18.10.9—Ductile Coupled Walls
Very ductile behavior should ℓw ℓn ℓw
be expected where well-
detailed slender walls are
coupled by ductile coupling
beams aligned over the h
building height.
hwcs
WWW.CONCRETE.ORG/ACI318 258
18.10.9—Ductile Coupled Walls
• Individual walls satisfy ℓn
ℓw ℓw
– hwcs/ℓw ≥ 2
• All coupling beams must
satisfy:
– ℓn/h ≥ 2 at all levels h
– ℓn/h ≤ 5 at a floor level in at least
90% of the levels of the building
hwcs
– Development into adjacent wall
segments, 1.25fy (18.10.2.5)
• Anticipate new structural
system in ASCE 7 loadings
code.
WWW.CONCRETE.ORG/ACI318 259
ACI 318-19
Cambios en la norma de diseño
del concreto estructural
Cimentaciones
WWW.CONCRETE.ORG/ACI318 260
18.13.4 — Amarres sísmicos de cimentación
CDS C a F
• Amarres sísmicos u otros tipos
CDS D, E o F, con perfiles Clase E o F
• Se requieren amarres sísmicos
WWW.CONCRETE.ORG/ACI318 261
18.13.4.3 — Amarres sísmicos
Fuerza mínima en tracción y Carga de
columna
compresión en el amarre
• Carga desde el cabezal de
pilote o columna
– Mayor en cualquiera de los
extremos Fuerza del
amarre
• 0.1SDS x Carga muerta y
carga viva mayorada por
columna
WWW.CONCRETE.ORG/ACI318 262
18.13.5 — Cimentaciones profundas
WWW.CONCRETE.ORG/ACI318 263
18.13.5.2 — Cimentaciones profundas
CDS C a F
• Resistencia a las cargas de
tracción
→ Refuerzo longitudinal
continuo en todo su largo para
resistir la fuerza de tracción de
diseño
WWW.CONCRETE.ORG/ACI318 264
18.13.5.3 — Cimentaciones profundas
Cabezal de pilote
CDS C a F
• Refuerzos transversales
y longitudinales deben
extenderse:
– En toda la longitud al aire,
en agua o tierra suelta no
apoyada lateralmente.
WWW.CONCRETE.ORG/ACI318 265
18.13.5.4 y 18.13.5.5 — Cimentaciones profundas
CDS C a F
• Estribos cerrados de
confinamiento, espirales o
amarres terminan con
ganchos sísmicos D
WWW.CONCRETE.ORG/ACI318 266
18.13.5.6 — Cimentaciones profundas
• CDS D, E o F
– Pilotes, pilas o cajones de
cimentación y amarres de
cimentación que soportan
muros de carga de
aporticamiento ligero de uno
y dos pisos
– Exentos de refu. transv. de
18.13.5.3 a 18.13.5.5
WWW.CONCRETE.ORG/ACI318 267
18.13.5.7 — Pilotes construidos en sitio sin camisa
metálica
CDS C Cabezal
1/3 ℓpile de pilote
•ℓbar ≥ 3m
Amarres o espirales
3dpile
cerrados ≥ n.º 10
Distancia hasta 0.4Mcr > Mu
•Zona de confinamiento
transversal
ℓbar
s
• 3 dpile desde la parte inferior del
cabezal de pilote dpile
• s ≤ 150 mm; 8db barra long.
ℓbar
s
• s of 18.7.5.3
• rmin ≥ 0.06 fc′/fyt
dpile
•Refuerzo transversal extendido
12db barra long.
s≤ 0.5dpile rmin ≥ 0.005
300 mm
ℓbar
s
• s of 18.7.5.3
• rmin ≥ 0.06 fc′/fyt
dpile
•Refuerzo tranversal extendido
12db barra long. rmin ≥ 0.005
s≤ 0.5dpile
300 mm
ℓbar = longitud mínima del pilote reforzado
WWW.CONCRETE.ORG/ACI318 270
18.13.5.8 —Pilotes de concreto con camisa
metálica Cabezal de
CDS C a F pilote
ℓbar
pilotes sin camisa
dpile
WWW.CONCRETE.ORG/ACI318 271
18.13.5.9— Pilotes de tubos rellenos de concreto
ℓcabezal de pilote
Cabezal
CDS C a F
de pilote
•rmin ≥ 0.01
2ℓcabezal de pilote ≥
•ℓd,pile ≥ 2ℓcabezal de pilote
ℓdt,bar
ℓd
dpile
Tubo de acero
WWW.CONCRETE.ORG/ACI318 272
18.13.5.10 — Pilotes prefabricados no
preesforzados Cabezal
de pilote
CDS C Amarres cerrados o
espirales ≥
n.º 10 (≤ 500 mm) o
•ℓbar Longitud total del pilote n.º 13 (> 500 mm);
18.7.5.2
•Zona de confinamiento
transversal
• 3 dpile desde la parte inferior del
ℓbar
s
cabezal de pilote
• s ≤ 150 mm; 8db barra long.
dpile
•Refuerzo transversal
extendido rmin ≥ 0.01
• s ≤ 150 mm
WWW.CONCRETE.ORG/ACI318 273
18.13.5.10 — Pilotes prefabricados no
preesforzados Cabezal
de pilote
CDS D, E o F Amarres cerrados o
espirales ≥
n.º 10 (≤ 500 mm) o
•Igual que CDS C n.º 13 (> 500 mm);
18.7.5.2
•Satisface la Tabla 18.13.5.7.1
para CDS D, E y F
ℓbar
s
dpile
rmin ≥ 0.01
WWW.CONCRETE.ORG/ACI318 274
18.13.5.10 — Pilotes prefabricados
preesforzados
Cabezal
de pilote
CDS C a F
•Satisface 18.13.5.10.4 hasta
18.13.5.10.6
•Cantidad y espaciamiento
mínimos del refuerzo
ℓbar
s
transversal
dpile
WWW.CONCRETE.ORG/ACI318 275
18.13.6 — Anclaje de pilotes, pilas y cajones
de cimentación
CDS C a F
• Cargas de tracción:
trayectoria de carga a
pilotes, pilas o cajones de
cimentación Fuente: Diariocivil
• Transferencia al refuerzo
longitudinal en
cimentación profunda
Fuente: StockQueries
WWW.CONCRETE.ORG/ACI318 276
18.13.6 — Anclaje de pilotes, pilas y cajones
de cimentación tablero
Espigo
18.13.6.2 CDS C a F
ℓd compr.
ℓdt tracción
espiral
pilote
CDS C a F
• Para elementos de cimentación que
soportan el sistema primario de resistencia
ante fuerzas sísmicas
• ϕ para cortante debe ≤ el menor valor de
– ϕ para cortante utilizado para columna especial
– ϕ para cortante utilizado para muro especial
WWW.CONCRETE.ORG/ACI318 278
ACI 318-19
Cambios en la norma de diseño
del concreto estructural
Longitud de
desarrollo
WWW.CONCRETE.ORG/ACI318 279
Longitud de desarrollo
WWW.CONCRETE.ORG/ACI318 280
Longitud de desarrollo
esfuerzo de adherencia
distribución de las
fuerzas
WWW.CONCRETE.ORG/ACI318 281
Longitud de desarrollo de barras corrugadas y
alambres corrugados en tracción
WWW.CONCRETE.ORG/ACI318 282
Longitud de desarrollo de barras corrugadas
y alambres corrugados en tracción
• Modificaciones
de las
disposiciones
simplificadas de
25.4.2.3
• Ψg : nuevo
factor de
modificación
basado en el
grado de
refuerzo
• Modificación en
la Tabla 25.4.2.3
WWW.CONCRETE.ORG/ACI318 283
Longitud de desarrollo de barras corrugadas
y alambres corrugados en tracción
• Modificación en la ecuación general de la
longitud de desarrollo 25.4.2.4(a)
Factores de modificación
l : Concreto liviano
t : Posición de las barras
fy t e s g e : Epóxico
= db s : tamano del refuerzo
d
1.1l f cb + K tr
'
c
d g : Grado del refuerzo
b
• Requisito 25.4.2.2
Ktr ≥ 0.5db para fy ≥ 550 MPa , si espaciamiento
longitudinal de la barra < 150 mm
WWW.CONCRETE.ORG/ACI318 284
Longitud de desarrollo de barras corrugadas y
alambres corrugados en tracción
WWW.CONCRETE.ORG/ACI318 285
Longitud de desarrollo de barras corrugadas y
alambres corrugados en tracción
Grado g ℓd,Gr#/ℓd,Gr60
WWW.CONCRETE.ORG/ACI318 288
Longitud de desarrollo de ganchos estándar
en tracción
• Modos de falla
WWW.CONCRETE.ORG/ACI318 290
Longitud de desarrollo de ganchos estándar
en tracción
n.º 16
n.º 19
n.º 22 n.º 16
n.º 25 n.º 19
n.º 25
n.º 29 n.º 22
n.º 36 n.º 36
n.º 16 n.º 16
n.º 19
n.º 19 n.º 25
n.º 22 n.º 22
n.º 25 n.º 36
n.º 29
n.º 36
0 35 70 105 140
0 35 70 105 140
Resistencia a la compresión del concreto (MPa)
Resistencia a la compresión del concreto (MPa) Resultados de ensayos
Resultados de ensayos no confinados
confinados
WWW.CONCRETE.ORG/ACI318 291
Longitud de desarrollo de ganchos estándar en
tracción
- 25.4.3.1—La longitud de desarrollo de los ganchos
estándar en tracción es la mayor entre (a) y (c):
- Factores de modificación
𝝍𝒓 : Confinamiento del refuerzo (redefinición)
𝝍𝒐 : Ubicación (nuevo)
𝝍𝒄 : Resistencia del concreto (nuevo – utilizado como
recubrimiento en el pasado)
WWW.CONCRETE.ORG/ACI318 292
Longitud de desarrollo de ganchos está. en
tracción
318S-14
318-19
WWW.CONCRETE.ORG/ACI318 293
Longitud de desarrollo de ganchos estándar
en tracción
318S-14
318-19
WWW.CONCRETE.ORG/ACI318 297
Longitud de desarrollo de ganchos estándar
en tracción
WWW.CONCRETE.ORG/ACI318 298
Ejemplo — Longitud de desarrollo del gancho
estándar
Barras con gancho estándar; f'c = 28 MPa
700
318-14
600
Development Length, ℓdh (mm)
318-19
500
400
300
Barras con gancho estándar; f'c = 40 MPa
200
700
100 318-14
600
300
200
100
0
10 15 20 25 30 35 40
Bar diameter; mm
WWW.CONCRETE.ORG/ACI318 301
Longitud de desarrollo
cuña de concreto
fuerza en la barra
fisura de hendimiento
hendimiento radial
WWW.CONCRETE.ORG/ACI318 302
Longitud de desarrollo en tracción de barras
corrugadas con cabeza
25.4.4.1 Se permite el uso de una cabeza para desarrollar
una barra corrugada en tracción si se cumple con las
condiciones (a) a (f):
(a)La barra debe cumplir con 20.2.1.6
(b)El fy de la barra no debe exceder 420 MPa
(b) El tamaño de la barra no debe exceder la No. 36
(c) La superficie de apoyo neta de la cabeza Abrg debe ser al
menos 4Ab
(d) El concreto debe ser de peso normal
(e) El recubrimiento libre de la barra debe ser al menos 2db
(f) Espaciamiento centro a centro entre las barras debe ser
mínimo de 3db
WWW.CONCRETE.ORG/ACI318 303
Longitud de desarrollo de barras corrugadas con
cabeza en tracción
n.º 16a
n.º 16a
n.º 16b
n.º 16b
n.º 25a
n.º 25a
n.º 25b
n.º 25b
n.º 25c
n.º 25c
n.º 36a
n.º 25d
n.º 25d
n.º 36a
n.º 36b
n.º 36b
n.º 36c
n.º 36c
n.º 16a
n.º 16a
n.º 16b
n.º 16b
n.º 25a
n.º 25a
n.º 25b
n.º 25b
n.º 25c
n.º 25c
n.º 36a
n.º 25d
n.º 25d
n.º 36a
n.º 36a
n.º 36b
n.º 36b
0 35 70 105 140 n.º 36c
(a)
(b) 8db
(c) 150 mm
- Factores de modificación
𝝍𝒑 : Refuerzo de estribos paralelos
𝝍𝒐 : Ubicación
𝝍𝒄 : Resistencia del concreto
WWW.CONCRETE.ORG/ACI318 305
Longitud de desarrollo de barras
corrugadas con cabeza en tracción
WWW.CONCRETE.ORG/ACI318 306
Longitud de desarrollo de barras corrugadas
con cabeza en tracción
• Refuerzo de estribos paralelos (Att)
– localizarlos dentro de 8db de la línea central de la barra
con cabeza hacia el centro del nudo
WWW.CONCRETE.ORG/ACI318 307
ACI 318-19
Changes to the Concrete
Design Standard
Shear Modifications
WWW.CONCRETE.ORG/ACI318 311
ACI 318-19
Changes to the Concrete
Design Standard
One-way Shear
Equations
WWW.CONCRETE.ORG/ACI318 315
317
Vc = 0.17l f c' bw d
Av Av ,min
Vtest/Vn = 1
Depth, d (mm)
Figure: Strength Ratio (Vtest/Vn) that was calculated by 318M-14 Simplified
WWW.CONCRETE.ORG/ACI318 317
Collins, et al., Concrete International, November 2015
WWW.CONCRETE.ORG/ACI318 318
320
Vc = 0.17l f c' bw d
Av Av ,min
Vtest/Vn = 1
WWW.CONCRETE.ORG/ACI318 320
321
Vc = 0.17l f c' bw d
Av Av ,min
Vtest/Vn = 1
Depth, d (mm)
WWW.CONCRETE.ORG/ACI318 321
ACI 318-19 New one-way shear equations
Table 22.5.5.1 - Vc for nonprestressed members
Criteria Vc
𝑁𝑢
0.17𝜆 𝑓′𝑐 + 𝑏𝑤 𝑑 (a)
Either 6𝐴𝑔
Av ≥ Av,min
of: 1Τ3
𝑁𝑢
0.66𝜆 𝜌𝑤 𝑓′𝑐 + 𝑏𝑤 𝑑 (b)
6𝐴𝑔
1Τ3
𝑁𝑢
Av < Av,min 0.66𝜆𝑠 𝜆 𝜌𝑤 𝑓′𝑐 + 𝑏𝑤 𝑑 (c)
6𝐴𝑔
Notes:
1. Axial load, Nu, is positive for compression and negative for tension
2. Vc shall not be taken less than zero.
WWW.CONCRETE.ORG/ACI318 326
Size effect – what is ls? 2
ls = 1.0
1 + 0.004d
1.2
0.8
λs
0.6
0.4
0.2
0
0 12
300 24
600 36
900 48
1200 60
1500 72
1800 84 96 2700
2100 2400 108 3000
120
Depth
Depth inin mm
inches
WWW.CONCRETE.ORG/ACI318 329
ACI 318-19 New one-way shear equations
Table 22.5.5.1 - Vc for nonprestressed members
Criteria Vc
𝑁𝑢
0.17𝜆 𝑓′𝑐 + 𝑏𝑤 𝑑 (a)
Either 6𝐴𝑔
Av ≥ Av,min
of: 1Τ3
𝑁𝑢
0.66𝜆 𝜌𝑤 𝑓′𝑐 + 𝑏𝑤 𝑑 (b)
6𝐴𝑔
1Τ3
𝑁𝑢
Av < Av,min 0.66𝜆𝑠 𝜆 𝜌𝑤 𝑓′𝑐 + 𝑏𝑤 𝑑 (c)
6𝐴𝑔
Notes:
1. Axial load, Nu, is positive for compression and negative for tension
2. Vc shall not be taken less than zero.
WWW.CONCRETE.ORG/ACI318 330
Other limitations for Table 22.5.5.1
• Provision 22.5.5.1.1:
– Limits the maximum value of Vc
Vc 0.42l f c' bw d
• Provision 22.5.5.1.2:
– Limits the maximum value of the Nu/6Ag term
Nu
0.05 f c'
6 Ag
WWW.CONCRETE.ORG/ACI318 331
RC Beams without shear reinforcement
Vtest/Vn
2.0 ACI 318 criteria 2.0
1.5 1.5
1.0 1.0
0.5 0.5
0.0 0.0
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
Depth, mm Depth, mm
WWW.CONCRETE.ORG/ACI318 332
Key points in application of new equations
WWW.CONCRETE.ORG/ACI318 337
Examples: SP-17(14) 5.7 One-way slab Example 1
• Span = 4.3 m
• Live load = 490 kg/m2
• Slab = 175 mm thick
• f’c = 35 MPa
• No. 16 bars at 300 mm
• d ~ 150 mm
• b = 300 mm
• Av = 0 mm2
• As = 632 mm2/ft
• Vu= 35 kN/m
WWW.CONCRETE.ORG/ACI318 338
Examples: SP-17(14) 5.7 One-way slab Example 1
WWW.CONCRETE.ORG/ACI318 339
Examples: SP-17(14) 5.7 One-way slab Example 1
653
rw = = 0.0044 low r w
(1000)(150)
fVc = (0.75)(0.66)(1)(1) ( 0.0044 )
1
3
28(1000)(150)
35(1000)(150)
fVc = 64.4
72 kNkN 35 kN OK
WWW.CONCRETE.ORG/ACI318 340
Examples: SP-17(14) 11.6 Foundation Example 1
• ℓ = 3.6 m
• h = 750 mm
• d ~ 650 mm 500 mm x 500 mm
• 13-No. 25 bars
0 in.
ft –mm
• b = 3.6 m
3900
• Av = 0 mm2
• As = 6630 mm2
• Analysis Vu= 1028 kN
WWW.CONCRETE.ORG/ACI318 342
Examples: SP-17(14) 11.6 Foundation Example 1
fVc = f0.17l f bd c
'
WWW.CONCRETE.ORG/ACI318 343
Examples: SP-17(14) 11.6 Foundation Example 1
• SP-17(14) One-way shear calc ACI 318-19
• Av ≤ Av,min, Eq. 22.5.5.1(c)
• Per ACI 318-19 (13.2.6.2), neglect size effect
for:
– One-way shallow foundations
– Two-way isolated footings
– Two-way combined and mat foundations
1
fVc = f0.66l (r w ) 3 '
f bd
c
WWW.CONCRETE.ORG/ACI318 344
Examples: SP-17(14) 11.6 Foundation Example 1
• SP-17(14) One-way shear calc ACI 318-19
• Av ≤ Av,min, Eq. 22.5.5.1(c)
1
fVc = f0.66l (r w ) 3
f c' bd
6630 mm 2
rw = = 0.0028
(3600 mm)(650 mm)
fVc = (0.75)(0.66)(1) ( 0.0028 )
1
3
28 MPa (3600 mm)(650 mm)
fVc = 864 kN 1028 kN NG No good
WWW.CONCRETE.ORG/ACI318 345
ACI 318-19
Changes to the Concrete
Design Standard
Two-way Shear
Equations
WWW.CONCRETE.ORG/ACI318 350
Two-way shear size effect
sd
0.083 2 + l
s l f c
'
(c)
bo
WWW.CONCRETE.ORG/ACI318 352
Two-way shear low r effect
• D, L only, cracking ~0. 𝟏𝟕 𝒇′𝒄 ; punching
0. 𝟑𝟑 𝒇′𝒄
• Aggregate interlock
• Low r ➔ bar yielding, ↑ rotation, ↑crack
size, allows sliding of reinforcement
• Punching loads < 0. 𝟑𝟑 𝒇′𝒄
WWW.CONCRETE.ORG/ACI318 353
New two-way slab reinforcement limits
8.6.1—Reinforcement limits
• As,min ≥ 0.0018Ag
0.42vuvbslabbo
• Then As ,min
f s f y
WWW.CONCRETE.ORG/ACI318 354
ACI 318-19
Changes to the Concrete
Design Standard
WWW.CONCRETE.ORG/ACI318 358
Coordination of Chap. 11 and 18 Wall Shear Eqs.
• 318M-14 • 318M-19
– Chapter 11 – Chapter 11
𝐴𝑣 𝑓𝑦𝑡 𝑑
𝑉𝑛 = 0.17𝜆 𝑓𝑐′ ℎ𝑑 + 𝑉𝑛 = 𝛼𝑐 𝜆 𝑓𝑐′ + 𝜌𝑡 𝑓𝑦𝑡 𝐴𝑐𝑣
𝑠
– Chapter 18 – Chapter 18
WWW.CONCRETE.ORG/ACI318 360
Coordination of Chap. 11 and 18 Wall Shear Eqs.
• 318-19 Eq. 11.5.4.3 and Eq. 18.10.4.1
( )
Vn = c l f c' + rt f yt Acv
0.25
0.17
WWW.CONCRETE.ORG/ACI318 361
Coordination of Chap. 11 and 18 Wall Shear Eqs.
• Maximum permissible shear
– 318-14: 𝑽𝒏 ≤ 𝟎. 𝟖𝟑 𝒇′𝒄 𝑨𝒄𝒗 where typically 𝑨𝒄𝒗 = 𝟎. 𝟖ℓ𝒘 𝒉
– 318-19: 𝑽𝒏 ≤ 0.67 𝒇′𝒄 𝑨𝒄𝒗 where typically 𝑨𝒄𝒗 = ℓ𝒘 𝒉
• Net result: Maximum permissible shear
essentially the same in Chapter 11 of ACI 318-
14 and ACI 318-19
WWW.CONCRETE.ORG/ACI318 362
ACI 318-19
Changes to the Concrete
Design Standard
Spacing of Shear
Reinforcement
WWW.CONCRETE.ORG/ACI318 363
Maximum spacing of legs of shear reinforcement
Source: Lubell et. al, “Shear Reinforcement Spacing in Wide Members, ACI Structural Journal 2009
WWW.CONCRETE.ORG/ACI318 364
Table 9.7.6.2.2—Maximum spacing of legs of
shear reinforcement
Maximum s, mm
Nonprestressed beam Prestressed beam
Required Vs
Across Along Across
Along length
length length length
d/2 d 3h/4 3h/2
0.33 f b d'
c w
Lesser of:
600 mm
d/4 d/2 3h/8 3h/4
0.33 f b d'
c w Lesser of
300 mm
WWW.CONCRETE.ORG/ACI318 365
Maximum spacing of legs of shear reinforcement
Bi-directional Shear
WWW.CONCRETE.ORG/ACI318 367
Interaction of shear forces
• Biaxial shear
• Symmetrical RC circular sections
– fVn equal about any axis (assuming constant Nu).
– Vu on 2 centroidal axes, Vu = resultant
vu = (vu , x ) + (vu , y )
2 2 vu,y
vu,x
WWW.CONCRETE.ORG/ACI318 368
Interaction of shear forces
• Biaxial shear
• Rectangular RC sections
– fVn differs between axes
– Vu on 2 axes, strength along
resultant unclear.
vu,y
vu,x
vu
WWW.CONCRETE.ORG/ACI318 369
2.5
Vexp(y)/Vpre(y)
1.5
WWW.CONCRETE.ORG/ACI318 370
ACI 318-19
Changes to the Concrete
Design Standard
Hanger
Reinforcement
WWW.CONCRETE.ORG/ACI318 372
Monolithic beam-to-beam joints: Hanger steel
WWW.CONCRETE.ORG/ACI318 373
Monolithic beam-to-beam joints: Hanger steel
WWW.CONCRETE.ORG/ACI318 374
ACI 318-19
Cambios en la norma de diseño
de concreto estructural
WWW.CONCRETE.ORG/ACI318 375
Cambios en la durabilidad y los materiales
• Cambios en las propiedades de los materiales (19.2)
– Requisitos mínimos adicionales de f’c
– Requisitos del Ec
• Cambios en la durabilidad (19.3)
– Cálculo del contenido de iones de cloruro
– Categoría de exposición a los sulfatos S3
– Categoría de exposición al agua W
– Categoría de exposición a la corrosión C0
• Cambios en el material (26.4.1)
– Cementos alternativos
– Agregados nuevos
• Agregados reciclados
• Adiciones minerales
• Evaluación y aceptación (26.12)
– Ensayos de resistencia
• Inspección (26.13)
WWW.CONCRETE.ORG/ACI318 376
Tabla 19.2.1.1 —
Resistencia mínima adicional, f'c
Mín. f’c
Muros estructurales en CDS D, E y F (MPa)
Muros estructurales especiales con refuerzo Grado 690 35
WWW.CONCRETE.ORG/ACI318 378
19.2.2.2 Módulo de elasticidad
Ec puede especificarse con base
en ensayos de mezclas de
concreto:
Crédito:
PCA
WWW.CONCRETE.ORG/ACI318 384
Nuevos materiales permitidos
WWW.CONCRETE.ORG/ACI318 391
Nuevos materiales permitidos
WWW.CONCRETE.ORG/ACI318 392
26.12 — Evaluación y aceptación de
concreto endurecido
• 26.12.1.1
– Normas de ASTM añadidas para muestreo, cilindros
y ensayos
– Muestras tomadas en el punto de entrega
– Certificación requerida de los técnicos en ensayos
en la obra y en el laboratorio
– Se aclaró que un "ensayo de resistencia"
corresponde al promedio de al menos dos cilindros
de 150 x 300 mm o tres cilindros de 100 x 200 mm
WWW.CONCRETE.ORG/ACI318 394
26.12.6 Investigación de los ensayos de
resistencia
(d) Ensayo de núcleos:
• Mín. 5 días después de haberse humedecido
• Máx. 7 días después de haber sido extraídos
A menos que sea aprobado de otra manera
por el profesional facultado para diseñar o la
autoridad competente
WWW.CONCRETE.ORG/ACI318 400
ACI 318-19
Changes to the Concrete
Design Standard
Strut-and-Tie Method
WWW.CONCRETE.ORG/ACI318 404
Why strut-and-tie method?
WWW.CONCRETE.ORG/ACI318 405
Strut and Tie Method
WWW.CONCRETE.ORG/ACI318 406
Deletion of bottle-shaped strut
Bottle-shaped strut
• Concentrated load spreads out at a slope of 2:1
• Leads to splitting stress, which weakens strut
• Actual behavior in a shear span more complicated.
• Bottle-shaped strut concept dropped in ACI 318-19
WWW.CONCRETE.ORG/ACI318 407
23.4 Strength of struts
• 3 components
– Struts
– Ties
– Nodal zones
Strut strength:
Fns = fce Acs + A’s f’s
and
fce = 0.85csf’c
WWW.CONCRETE.ORG/ACI318 408
23.4 Strength of struts
Strut coefficient, βs → Table 23.4.3
Strut location Strut type Criteria s
Tension members or
tension zones of Any All cases 0.4 (a)
members
Boundary
All cases 1.0 (b)
strut
Reinforcement satisfying (a)
0.75 (c)
All other cases or (b) of Table 23.5.1
Interior 𝑽𝒖 ≤ 𝝓(𝟎. 𝟒𝟑)𝝀𝝀𝒔 𝒇′𝒄 𝒃𝒘 𝒅 𝐭𝐚𝐧 𝜽 0.75 (d)
struts
Beam-column joints 0.75 (e)
All other cases 0.4 (f)
WWW.CONCRETE.ORG/ACI318 409
Minimum Reinforcement of D Regions
3.5
3
Strength Ratio (Vtest/Vstm)
2.5
1.5
0.5
0.25%
0
0 0.002 0.004 0.006 0.008 0.01
** 9.9.3.1 & 9.9.4.3 requires that deep beams be reinforced per (a).
23.5.1 requires all other components be reinforced per (a) or (b),
except where the strut is laterally constrained by concrete.
WWW.CONCRETE.ORG/ACI318 411
23.5 What is a laterally-restrained strut?
a) Discontinuity region is continuous ┴ to plane of
the strut-and-tie model.
Discontinuity Region
WWW.CONCRETE.ORG/ACI318 412
23.5 What is a laterally-restrained strut?
b) Concrete restraining strut extends beyond
each side face of strut a dist. ≥ 1/2 ws
WWW.CONCRETE.ORG/ACI318 414
23.4 Strength of struts
Strut coefficient, βs → Table 23.4.3
Strut location Strut type Criteria s
Tension members or
tension zones of Any All cases 0.4 (a)
members
Boundary
All cases 1.0 (b)
strut
Reinforcement satisfying (a)
0.75 (c)
All other cases or (b) of Table 23.5.1
Interior 𝑽𝒖 ≤ 𝝓(𝟎. 𝟒𝟑)𝝀𝝀𝒔 𝒇′𝒄 𝒃𝒘 𝒅 𝐭𝐚𝐧 𝜽 0.75 (d)
struts
Beam-column joints 0.75 (e)
All other cases 0.4 (f)
WWW.CONCRETE.ORG/ACI318 415
23.2.8 Effect of Prestressing
1600
12-13 Strand
1140
1187 mm2 110
1233 kN
1820 1820
1600
800 800
800
800
800 800
910 910 910 910
WWW.CONCRETE.ORG/ACI318 422
23.2.8 Effect of Prestressing in STM
WWW.CONCRETE.ORG/ACI318 423
23.7 Strength of ties
Tensile strength:
– Simple tension element
– Fnt = Atsfy +AtpDfp
– f = 0.75 for all ties
• Atp = 0 (nonprestressed)
• Δfp = 420 MPa for bonded prestressed reinf. and
70 MPa for unbonded prestressed reinf.
• T Δfp,max = fpy - fse
Note: tie centroid coincides with reinforcement centroid
WWW.CONCRETE.ORG/ACI318 424
23.10 Curved-bar Nodes
WWW.CONCRETE.ORG/ACI318 438
23.10 Curved-bar Nodes
C-T-T
q < 180 degree bend T
2 Ats fy C
rb '
bf s c
WWW.CONCRETE.ORG/ACI318 442
23.10 Curved-bar Nodes
23.10.6 The curve must be
sufficient to develop
difference in force
In terms of rb
2 d (1 − tan qc ) d b
rb −
2
WWW.CONCRETE.ORG/ACI318 447
23.11 Earthquake-resistant design using STM
Wall Transfer
a b force e f
Opening
d c h g
WWW.CONCRETE.ORG/ACI318 449
Earthquake-resistant design using STM
1. Chapter 18
WWW.CONCRETE.ORG/ACI318 450
23.11 Earthquake-resistant design using STM
WWW.CONCRETE.ORG/ACI318 451
23.11 Earthquake-resistant design using STM
WWW.CONCRETE.ORG/ACI318 452
ACI 318-19
Cambios en la norma de diseño
de concreto estructural
Concreto lanzado
WWW.CONCRETE.ORG/ACI318 454
Concreto lanzado
• Concreto lanzado
es igual al
concreto normal
• Método de
colocación
• Información
adicional en ACI
506R y ACI 506.2
WWW.CONCRETE.ORG/ACI318 455
Concreto lanzado
WWW.CONCRETE.ORG/ACI318 456
Concreto lanzado
Dos procesos
• Mezcla húmeda
• Mezcla seca
WWW.CONCRETE.ORG/ACI318 457
Concreto lanzado — Espaciamiento mínimo
del refuerzo
• 25.2.10
– Para estribos, estribos cerrados de confinamiento, y
refuerzos en espiral en columnas a ser colocadas
con concreto lanzado, el mínimo espaciamiento
libre será de 75 mm.
≥ 75 mm
WWW.CONCRETE.ORG/ACI318 460
Concreto lanzado
Paneles de pruebas
WWW.CONCRETE.ORG/ACI318 462
Concreto lanzado
• Paneles de prueba
WWW.CONCRETE.ORG/ACI318 463
Concreto lanzado
WWW.CONCRETE.ORG/ACI318 464
Concreto lanzado
WWW.CONCRETE.ORG/ACI318 465
Concreto lanzado
26.5.6: Construcción, juntas de construcción,
contracción y dilatación
• corte a 45° a menos que se designe una junta
a escuadra
• Remitir las ubicaciones al profesional
facultado para diseñar para su aprobación
– Para juntas no indicadas en los documentos de
construcción
WWW.CONCRETE.ORG/ACI318 470
Concreto lanzado
26.12 — Evaluación y 150 mm
aceptación
• Prueba de resistencia
– Resistencia media de un
mínimo de tres núcleos
de 75 mm de diámetro
de un panel de prueba 300 mm 450 mm
WWW.CONCRETE.ORG/ACI318 475
Nuevo en el ACI 318-19
• Nuevo Apéndice A sobre
análisis dinámico no lineal de
estructuras de concreto
reforzado, para la aplicación
del ASCE 7-16, el TBI (versión
2.0 de 2017) y el Los Angeles
Tall Buildings Design
Procedure (2017).
WWW.CONCRETE.ORG/ACI318 484
Nuevo en el ACI 318-19
• Nuevo Apéndice A sobre
análisis dinámico no lineal de
estructuras de concreto
reforzado, para la aplicación
del ASCE 7-16, el TBI (versión
2.0 de 2017) y el Los Angeles
Tall Buildings Design
Procedure (2017).
WWW.CONCRETE.ORG/ACI318 485
WWW.CONCRETE.ORG/ACI318 486
WWW.CONCRETE.ORG/ACI318 487
Contenido del nuevo
Apéndice A
A.1 — Nomenclatura y terminología
A.2 — Alcance
A.3 — Generalidades
A.4 — Movimientos sísmicos del terreno
A.5 — Factores y combinaciones de carga
A.6 — Modelaje y análisis
A.7 — Clasificación de las acciones y sus
condiciones críticas
A.8 — Rigidez efectiva
WWW.CONCRETE.ORG/ACI318 488
Contenido del nuevo
Apéndice A
A.9 — Resistencia de los materiales esperada
A.10 — Criterio de aceptación para acciones
controladas por deformación
A.11 — Resistencia esperada para acciones
controladas por fuerza
A.12 — Requisitos de detallado mejorados
A.13 — Revisión independiente del diseño
estructural
WWW.CONCRETE.ORG/ACI318 489
Alcance
WWW.CONCRETE.ORG/ACI318 490
Seleccion y modificacion de los
movimientos sísmicos del terreno
GeoPentech
WWW.CONCRETE.ORG/ACI318 491
Nivel de servicio y máximo
considerado (MCER)
3.5
Pseudo Spectral Acceleration, g
3.0
Maximum Considered Shaking (MCER)
2.5 (1000 to 2500-yr return period)
2.0
1.5
Service Level Earthquake (SLE)
1.0 (43-yr return period)
0.5
0.0
0 2 4 6 8 10
Period, sec
WWW.CONCRETE.ORG/ACI318 492
Fluencia objetivo Modelaje estructural
WWW.CONCRETE.ORG/ACI318 493
Modelaje de acciones controladas
por deformación
MKA
WWW.CONCRETE.ORG/ACI318 494
Criterio de aceptacion - SLE
Story drift ratio ≤ 0.005
Elevation
WWW.CONCRETE.ORG/ACI318 495
Criterio de aceptación - MCER
Mean transient story drift ratio ≤ 0.03 (Max ≤ 0.045)
Mean residual story drift ratio ≤ 0.01 (Max ≤ 0.015)
Elevation
WWW.CONCRETE.ORG/ACI318 496
Estadistica de las demandas
Value Source
WWW.CONCRETE.ORG/ACI318 497
Ecuaciones finales de factores de carga y
resistencia
III 1.25 5% 3%
IV 1.5 2.5% 1%
TBI 2017
WWW.CONCRETE.ORG/ACI318 498
Verificacion de desempeño:
Cortante en el núcleo
(psi)
0 0.5 1.0 (MPa)
MKA
WWW.CONCRETE.ORG/ACI318 499
Verificación de desempeño: Deformaciones
unitarias loigtudinales en la pared del núcleo
0.0000
MKA Compression Tension
WWW.CONCRETE.ORG/ACI318 500
WWW.CONCRETE.ORG/ACI318 501
Algunos resultados típicos
Limit
Limit
Limit
Height, ft
Height, ft
Height, ft
SLE story drift Max of mean MCER transient Max of mean MCER residual
ratio story drift ratio story drift ratio
WWW.CONCRETE.ORG/ACI318 502
Algunos resultados típicos
Limit
Height, ft
Limit
Height, ft
Max of mean MCER wall tensile
strain
Limit
Height, ft
WWW.CONCRETE.ORG/ACI318 503
OTROS ASPECTOS
IMPORTANTES
WWW.CONCRETE.ORG/ACI318 504
El %
¡La nueva
ingeniería
estructural!
WWW.CONCRETE.ORG/ACI318 505
Basta buscar la tecla
WWW.CONCRETE.ORG/ACI318 506
Es fácil
WWW.CONCRETE.ORG/ACI318 507
Oprimimos
WWW.CONCRETE.ORG/ACI318 508
… y podemos pasar
de datos a planos
sin que los revise
un humano!
WWW.CONCRETE.ORG/ACI318 509
¡Que susto!
Quedamos
fríos
WWW.CONCRETE.ORG/ACI318 510
Fin
WWW.CONCRETE.ORG/ACI318 511
ACI 318-19
Changes to the Concrete
Design Standard
Closing Remarks
WWW.CONCRETE.ORG/ACI318 512
An Invitation to Join – ACI Membership
WWW.CONCRETE.ORG/ACI318 513
WWW.CONCRETE.ORG/ACI318 514