Professional Documents
Culture Documents
KUBOTA Corporation
FOREWORD
You are now the proud owner of a KUBOTA Loader. This loader is a product of KUBOTA
quality engineering and manufacturing. It is made of fine materials and under a rigid
quality control system. It will give you long, satisfactory service. To obtain the best use of
your loader, please read this manual carefully. If your tractor is provided with CAB, also
read the CAB operator’s manual, which is a separate manual. It will help you become
familiar with the operation of the loader and contains many helpful hints about loader
maintenance. It is KUBOTA's policy to utilize as quickly as possible every advance in
our research. The immediate use of new techniques in the manufacture of products may
cause some small parts of this manual to be outdated. KUBOTA distributors and dealers
will have the most up-to-date information. Please do not hesitate to consult with them.
SAFETY FIRST
This symbol, the industry's "Safety Alert Symbol", is used throughout this manual
and on labels on the machine itself to warn of the possibility of personal injury.
Read these instructions carefully. It is essential that you read the instructions and
safety regulations before you attempt to assemble or use this unit.
All these products and all the services which accompany them,
however, are unified by one central commitment. KUBOTA
makes products which, taken on a national scale, are basic
necessities. Products which are indispensable. Products which
are intended to help individuals and nations fulfill the potential
inherent in their environment. KUBOTA is the Basic Necessities
Giant.
This potential includes water supply, food from the soil and from the
sea, industrial development, architecture and construction, and
transportation.
SAFE OPERATION
Most loader equipment accidents can be avoided by following simple safety precautions.
These safety precautions, if followed at all times, will help you operate your loader safely.
1. BEFORE OPERATING THE LOADER 10. Follow the precautions below when attaching
attachments.
1. Know your equipment and its limitations. A Make sure both handles (LH, RH) contact the ear
Allow only trained personnel to operate or service this plates at the points (A) and are all the way down.
equipment. A Make sure both lock pins (LH, RH) protrude through
2. Read and understand all instructions and precautions the pin slots.
found in both the tractor and the loader operator's A Kubota recommends the use of Kubota attachments
manuals before using the loader. on Kubota loaders. Non-Kubota attachments, if used,
Lack of knowledge can lead to accidents. must comply with ISO 24410, first edition 2005-04-15.
3. It is the owner's responsibility to ensure that anyone A Use of a non-Kubota attachment that does not comply
who will operate the loader reads this manual first and with ISO 24410 or the improper positioning of
becomes familiar with the safe operation of the loader. handle(s) or non-protrusion of pin(s) may result in
4. For your safety, a ROPS with a seat belt is strongly detachment of the attachment or deformation, causing
recommended by KUBOTA in almost all applications. loss of performance, personal injury or death.
If your tractor has a foldable ROPS, fold it down only
when absolutely necessary and raise it up and lock it
again as soon as possible. Do not wear the seat belt
when a foldable ROPS is down or a fixed ROPS is
removed. If you have any questions, consult your local
KUBOTA dealer.
Always use the seat belt when the tractor is equipped
with a ROPS. Never use the seat belt when the tractor
is not equipped with a ROPS.
5. Visually check for hydraulic leaks and broken, missing,
or malfunctioning parts.
Make necessary repairs before operating.
6. Replace damaged or illegible safety labels. See
following pages for required labels.
7. When the front loader is mounted on the tractor, enter
and exit the operator's seat only from left side of the (1) Handle (A) The handle contacts the ear
tractor. (2) Ear plate plate at the points.
8. Engage the loader control valve lock to prevent (3) Pin slot
accidental actuation when the implement is not in use (4) Lock pin
or during transport. Do not utilize the valve lock for
machine maintenance or repair.
9. Assemble, remove and reinstall the loader only as
directed in this manual. Failure to do this could result
in serious personal injury or death.
2 SAFE OPERATION
SERVICING OF LOADER
Your dealer is interested in your new loader and has the
desire to help you get the most value from it. After reading
this manual thoroughly, you will find that you can do some
of the regular maintenance yourself.
However, when in need of parts or major service, be sure
to see your KUBOTA dealer.
For service, contact the KUBOTA dealership from which
you purchased your loader or your local KUBOTA dealer.
When in need of parts, be prepared to give your dealer the
loader serial number.
Locate the serial numbers now and record them in the
space provided.
KUBOTA LOADER
Model
Serial Number
Date of Purchase
Name of Dealer
(To be filled in by purchaser)
SPECIFICATIONS
SUITABLE TRACTOR
LA764: L4600
LOADER SPECIFICATIONS
LOADER MODEL LA764
TRACTOR MODEL L4600
WHEEL BASE(WB) mm (in.) 2WD : 1850 (72.8) 4WD : 1845 (72.6)
FRONT TIRES 2WD : 7.5L - 15 4WD : 8.3 - 16
REAR TIRES 14.9 - 24
BORE mm (in.) 50 (1.97)
BOOM CYLINDER
STROKE mm (in.) 520 (20.5)
BORE mm (in.) 50 (1.97)
BUCKET CYLINDER
STROKE mm (in.) 480.5 (18.9)
3 Position bucket One Detent Float Position, Regenerative Bucket Dump,
CONTROL VALVE
control valve type Power Beyond Circuit
RATED FLOW L/min (GPM) 29.4 (7.8)
MAXIMUM PRESSURE MPa (kg/cm , psi) 17.7 (180, 2560)
NET WEIGHT(APPROXIMATE) kg (lbs.) 524 (1155)
SPECIFICATIONS 3
BUCKET SPECIFICATIONS
LOADER MODEL LA764
SQUARE 72" LIGHT
MODEL SQUARE 72" ROUND 72" HD
MATERIAL
TYPE QUICK ATTACH QUICK ATTACH QUICK ATTACH
WIDTH mm (in.) 1830 (72)
DEPTH (L) mm (in.) 547 (21.5) 477 (18.8) 607 (23.9)
HEIGHT (M) mm (in.) 570 (22.4) 608 (23.9) 570 (22.4)
LENGTH (N) mm (in.) 630 (24.8) 610 (24) 691 (27.2)
STRUCK m
0.31 (10.9) 0.36 (12.7)
(CU.FT.)
CAPACITY
HEAPED m
0.37 (13.1) 0.45 (16.0)
(CU.FT.)
WEIGHT kg (lbs.) 150 (331) 180 (397) 136 (300)
DIMENSIONAL SPECIFICATIONS
LOADER MODEL LA764
TRACTOR MODEL L4600
A MAX. LIFT HEIGHT (TO BUCKET PIVOT PIN) mm (in.) 2673 (105.2)
B MAX. LIFT HEIGHT UNDER LEVEL BUCKET mm (in.) 2431 (95.7)
C CLEARANCE WITH BUCKET DUMPED mm (in.) 2063 (81.2)
D REACH AT MAX. LIFT HEIGHT (DUMPING REACH) mm (in.) 571 (22.5)
E MAX. DUMP ANGLE deg. 41
F REACH WITH BUCKET ON GROUND mm (in.) 1783 (70.2)
G BUCKET ROLL-BACK ANGLE deg. 27
H DIGGING DEPTH mm (in.) 156 (6.1)
J OVERALL HEIGHT IN CARRYING POSITION mm (in.) 1387 (54.6)
4 SPECIFICATIONS
OPERATIONAL SPECIFICATIONS
LOADER MODEL LA764
TRACTOR MODEL L4600
U LIFT CAPACITY (BUCKET PIVOT PIN, MAX. HEIGHT) kg (lbs.) 764 (1684)
V LIFT CAPACITY (500 mm FORWARD, MAX. HEIGHT) kg (lbs.) 573 (1263)
W LIFT CAPACITY (BUCKET PIVOT PIN, 1500 mm HEIGHT) kg (lbs.) 977 (2154)
X LIFT CAPACITY (500 mm FORWARD, 1500 mm HEIGHT) kg (lbs.) 783 (1726)
Y BREAKOUT FORCE (BUCKET PIVOT PIN) N (lbf.) 14023 (3153)
Z BREAKOUT FORCE (500mm FORWARD) N (lbf.) 10865 (2443)
VV BUCKET ROLL-BACK FORCE AT MAX. HEIGHT N (lbf.) 12763 (2869)
XX BUCKET ROLL-BACK FORCE AT 1500 mm N (lbf.) 16429 (3673)
ZZ BUCKET ROLL-BACK FORCE AT GROUND LEVEL N (lbf.) 13345 (3000)
RAISING TIME (RATED FLOW) sec. 4.0
LOWERING TIME (RATED FLOW) sec. 2.5
BUCKET DUMPING TIME (RATED FLOW) sec. 1.6
BUCKET ROLLBACK TIME (RATED FLOW) sec. 2.5
SPECIFICATIONS 5
LA764
6 SPECIFICATIONS
LOADER TERMINOLOGY
PRE-OPERATION CHECK
LUBRICATION TREAD
Lubricate all grease fittings with SAE multipurpose 1. Set front tread as follows.
grease. Front Tread
2WD 4WD
7.5L-15 : 1280 mm (50.4 in.) Front axle is
L4600
6.00-16 : 1210 mm (47.6 in.) not adjustable.
TIRE INFLATION
BLiquid ballast in rear tires Ensure that the tractor tires are properly inflated.
Water and calcium chloride solution provides a safe and Refer to the tractor operator's manual for optional tires.
economical ballast. Used properly, it will not damage tires,
tubes or rims. The addition of calcium chloride is BInflation pressure
recommended to prevent the water from freezing. Use of
this method of weighting the wheels has full approval of Tire sizes Inflation Pressure
the tire manufacturers. See your tire dealer for this 14.9-24, 6PR 140 kPa (1.4 kgf/cm , 20 psi)
service. Rear 44 x 18-20, 4PR 140 kPa (1.4 kgf/cm , 20 psi)
Liquid weight per tire (75 Percent filled)
17.5L-24, 6PR 140 kPa (1.4 kgf/cm , 20 psi)
Tire sizes 14.9-24 17.5L-24
6.00-16, 4PR 220 kPa (2.2 kgf/cm , 32 psi)
Slush free at -10 (14 ) 8.3-16, 6PR 150 kPa (1.5 kgf/cm , 22 psi)
Solid at -30 (-22 ) 205 kg 235 kg
[Approx. 1 kg (2 lbs.) (450 lbs.) (515 lbs.) 27 x 8.50-15, 4PR 80 kPa (0.8 kgf/cm , 11 psi)
CaCl per 4 L (1 gal.) of water] 29 x 12.50-15, 4PR 140 kPa (1.4 kgf/cm , 20 psi)
Front
Slush free at -24 (-11 ) 10-16.5, 6PR 140 kPa (1.4 kgf/cm , 20 psi)
Solid at -47 (-52 ) 215 kg 250 kg
[Approx. 1.5 kg (3.5 lbs.) (475 lbs.) (550 lbs.) 7.5L-15, 6PR 220 kPa (2.2 kgf/cm , 32 psi)
CaCl per 4 L (1 gal.) of water] 27-10.50LL15, 4PR 80 kPa (0.8 kgf/cm , 11 psi)
Slush free at -47 (-52 ) 305R343 140 kPa (1.4 kgf/cm , 20 psi)
Solid at -52 (-62 ) 225 kg 265 kg
[Approx. 2.25 kg (5 lbs.) (495 lbs.) (585 lbs.)
CaCl per 4 L (1 gal.) of water] TEST OPERATION
A Do not fill tires with water or solution more than 75% of
full capacity (to the valve stem level at 12 o'clock To avoid serious personal injury:
position). A Keep engine speed at low idle during the test
operation.
A Escaping hydraulic fluid under pressure can
have sufficient force to penetrate skin, causing
serious personal injury.
Before disconnecting lines, be sure to relieve
all pressure by moving the controls.
Before applying pressure to the system, be
sure all connections are tight and that lines,
tubes and hoses are not damaged.
Fluid escaping from a very small hole can be
almost invisible. Use a piece of cardboard or
wood, rather than your hands to search for
suspected leaks.
If injured by escaping fluid, see a doctor at
once. Serious infection or allergic reaction will
develop if proper medical treatment is not
(1) Air (A) Correct: 75% Full administered immediately.
(2) Water Air compresses like a cushion
(B) Incorrect: 100% Full
Water can not be compressed
Ease control lever toward you and then left to rollback and
lift the bucket.
LOADING FROM A BANK It is important to keep the bucket level when approaching
a bank or pile. This will help avoid gouging the work area.
Choose a forward gear that provides a safe ground speed
and power for loading.
LOADING LOW TRUCKS OR SPREADERS Leave dirt in the bucket because dumping on each pass
wastes time.
FROM A PILE
For faster loading, minimize the angle of turn and length
of run between pile and spreader.
Leave dirt which drifts over the side of the bucket for final
cleanup.
BACKFILLING
Approach the pile with the bucket flat.
(1) Bolt
(2) Indicator rod
(3) Guide, Indicator rod
-SQUARE 72''
WIDTH
1830mm (72in.)
STRUCK CAPACITY
0.31cu.m. (10.9cu.ft.)
-ROUND 72''HD
WIDTH
1830mm (72in.)
STRUCK CAPACITY
0.31cu.m. (10.9cu.ft.)
OVERALL HEIGHT
524mm (20.63in.) (1) Fork (36")
OVERALL WIDTH
1149mm (45.24in.) 2. Slide the fork to the desired position.
OVERALL LENGTH (INCLUDING MAIN SPEAR)
1376mm (54.17in.)
USEABLE LENGTH OF MAIN SPEAR
1008mm (39.69in.)
USEABLE LENGTH OF SPEAR 2
356mm (14.02in.)
MAXIMUM DIAMETER OF MAIN SPEAR
51mm (2.00in.)
DIAMETER OF SPEAR 2
32mm (1 1/4in.)
WEIGHT OF IMPLEMENT
74kg (163lbs)
BPallet fork
(1) Fork (36")
3. Push the lock lever and slide the fork slightly until the
lock pin engages with one of the notches to lock the
fork.
MAINTENANCE
RE-TIGHTENING OF HARDWARE
After 20 to 30 hours of initial loader operation, re-tighten
To avoid personal injury: all mounting bolts and nuts to the required torque value as
A Be sure to check and service the tractor on a follows.
flat surface with the bucket on the ground,
Required
engine shut off, the key removed and the
Sequence Location Bolt/Nut Torque N-m
parking brake on. (kgf-m, ft-lbs)
EVERY 50 HOURS
BChecking main frame bolt torque
SAE grade No. SAE GR.5 SAE GR.8 property class 8.8 Approx. SAE GR 5
10. Start the engine and run at idle. Slowly move the [Type B]
loader control lever to rollback position to raise the
loader side frames up and out of the receivers of the
main frames as shown.
(1) Hose
(2) Hose guide
14. Place the protective caps and plugs on the quick
coupler ends.
(1) Loader control lever
[Type A]
15. Start the engine and slowly back the tractor away from
the loader.
(1) Hose
(2) Hose guide
STORING THE LOADER 27
(1) Hoses
REINSTALLING THE LOADER 29
[Type A] [Type B]
(1) Hoses
(2) Hood
(3) Hose guide
(1) Stand
(2) Spring pin