Professional Documents
Culture Documents
Gases: Answers To Worked Examples
Gases: Answers To Worked Examples
8
Gases
Answers to worked examples
Strategy
Use Boyle’s law (Equation 8.1), which tells us that the pressure of a gas is
inversely proportional to its volume
𝑝 ∝ 1/𝑉
Solution
The volume of the balloon increases from V1 = 1 dm3 to V2 = 1.5 dm3, which is
a factor of 1.5. The pressure of gas within the balloon therefore decreases by
a factor of 1.5. The initial pressure is 1 atm, so that, according to Boyle’s law,
the final pressure is
𝑉1 1 dm3
1 atm × = 1 atm × = 0.67 atm
𝑉2 1.5 dm3
W.E. 8.2 Using columns of liquid to measure pressures (on p. 351 in Chemistry3)
The pressure at the top of a high mountain is 0.4 atm. Calculate the height of
the mercury column in a barometer at the top of the mountain.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Strategy
Rearrange Equation 8.6 and use it to calculate the height of the column of
mercury, remembering to use SI units throughout.
Solution
From Table 8.1 we know that
1 atm = 101325 Pa
1 × 10−3 kg
1g
and because 1 cm3 = 1 × 10–6 m3, then to convert from cm3 to m3 we must
multiply by
1 × 10−6 m3
1 cm3
−3
1 × 10−3 kg 1 × 10−6 m3
𝜌 = 13.6 g cm × × = 13600 kg m−3
1g 1 cm3
Rearranging Equation 8.6 and substituting the appropriate values for the
density, pressure and acceleration due to gravity
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
W.E. 8.3 Using the ideal gas equation to calculate the amount of gas (on p. 352 in
Chemistry3)
A gas cylinder contains 10 kg of oxygen at a pressure of 20 bar at 25°C.
Calculate the volume of the cylinder, in m3.
Strategy
Use the molar mass of oxygen to find the amount of substance, i.e. the
number of moles, of gas present. Rearrange the ideal gas equation to give an
expression for the volume and substitute the values, once converted to SI
units, for the pressure, temperature and amount of substance.
Solution
The molar mass of oxygen, O2, is
if the temperature on the Celsius scale is θ. The equation has been written in
this way to ensure that the units are consistent. Table 8.1 gives the
conversion factors for the various units of pressure, so that, because
1 bar ≡ 105 Pa,
𝑉 = 𝑛𝑅𝑇/𝑝
= 312 mol × 8.3145 J K −1 mol−1 × 298 K/20 × 105 J m−3
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
= 0.387 m3
It is helpful to express the units of pressure as J m–3 rather than Pa, in order
to help us to confirm that the units of the result are indeed the SI units of
volume, m3.
Strategy
Use the ideal gas equation, written in the form of Equation 8.7, remembering
to express the pressure in SI units.
Solution
We may simplify Equation 8.7 because we can assume that the temperature
remains constant
𝑝1 𝑉1 𝑝2 𝑉2
=
𝑇1 𝑇2
𝑝1 𝑉1 = 𝑝2 𝑉2
and rearrange it to give an expression for the final pressure
𝑝2 = 𝑝1 𝑉1 /𝑉2
𝑉1 /𝑉2 = 2
so that
Thus, halving the volume results in a doubling of the pressure, providing the
amount of substance and temperature remain constant.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
We may use the conversion factor in Table 8.1 to express this pressure in SI
units
although because the initial pressure was quoted to only one significant
figure, it is probably inappropriate to quote the pressure in pascals to this
level of precision.
W.E. 8.5 The molar volume of an ideal gas (on p. 354 in Chemistry3)
Calculate the molar volume (in m3) of an ideal gas at 1.00 atm and exactly
0°C.
Strategy
Use the ideal gas equation, Equation 8.5, remembering to express all values
in SI units.
Solution
Use of the conversion factors in Table 8.1 shows that a pressure of 1.00 atm
corresponds to
𝑉 = 𝑛𝑅𝑇/𝑝
𝑉m = 𝑅𝑇/𝑝
= 8.3145 J K −1 mol−1 × 273.15 K / 101325 J m−3
= 22.4 × 10−3 m3
Calculate the partial pressure of ethane in the gas at the same total pressure.
Give your answer in atm.
Strategy
Use Dalton’s law, Equation 8.10, to calculate the partial pressure of ethane
from its mole fraction and the total pressure.
Solution
If the mole fraction of ethane is 6%, then 6 out of every 100 molecules in the
gas are ethane. This is equivalent to a mole fraction of ethane of 0.06. We
may use Dalton’s law in the form of Equation 8.10 directly
𝑝C2H6 = 𝑥C2 H6 𝑝total = 0.06 × 5 atm = 0.3 atm
Calculate the root mean square speeds of helium molecules and carbon
dioxide molecules at 15°C.
Strategy
Use Equation 8.19, remembering to express the molar mass of the molecules
in units of kilogramme and the temperature in units of kelvin.
Solution
The molar mass of helium is
Applying Equation 8.19 then gives the speeds of helium atoms and carbon
dioxide molecules as
1/2
3𝑅𝑇 1/2 3 × 8.3145 J K −1 mol−1 × 298 K
𝑐He =( ) =( ) = 1363 m s−1
𝑀He 4.00 × 10−3 kg mol−1
and
1/2 1/2
3𝑅𝑇 3 × 8.3145 J K −1 mol−1 × 298 K
𝑐CO2 =( ) =( ) = 411 m s−1
𝑀CO2 44.01 × 10−3 kg mol−1
Strategy
Use Equation 8.21, which shows how the relative rates of effusion depend
upon the molar mass of the molecules.
Solution
We may apply Equation 8.21 directly, to express the rate of effusion of
oxygen and carbon dioxide relative to that of nitrogen. The molar masses of
the species are
1/2 1/2
Rate of effusion of O2 𝑀N 28.00 g mol−1
= ( 2) =( ) = 0.935
Rate of effusion of N2 𝑀O2 32.00 g mol−1
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
and
1/2 1/2
Rate of effusion of CO2 𝑀N2 28.00 g mol−1
=( ) =( ) = 0.798
Rate of effusion of N2 𝑀CO2 44.01 g mol−1
Calculate the collisional frequency in hydrogen gas at SATP and account for
the difference from that for nitrogen. (For H2, = 0.27 nm2 and the mean
speed, 𝑐̅ = 1780 m s −1 at 298 K.)
Strategy
Use Equation 8.22 directly.
Solution
If we note that
because 1 nm2 = 10–18 m2, and that standard ambient temperature and
pressure correspond to
and
𝑇 = 298 K
𝑝
𝑍 = √2𝑁𝐴 𝑐̅𝜎 ×
𝑅𝑇
= √2 × 6.022 × 1023 mol−1 × 1780 ms −1 × 0.27 × 10−18 m2
105 J m−3
×
8.3145 J K −1 mol−1 × 298 K
= 1.65 × 1010 s −1
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
The collisional frequency is 2.4× greater than that for nitrogen under the
same conditions because, even though the collision cross section of a
hydrogen molecule is smaller, the hydrogen molecules are moving much
faster because their mass is so small.
Strategy
Rearrange Equation 8.23 to obtain an expression for the pressure of a gas in
terms of the mean free path, collision cross section and temperature.
Solution
Rearranging Equation 8.23 gives
𝑅𝑇
𝑝=
√2𝑁A 𝜎𝜆
The collision cross section of N2 is given in Table 8.3 as = 0.43 nm2, which
is equivalent to 0.43 × 10–18 m2. The mean free path is = 10 cm, which is
equivalent to 0.1 m. Thus, substituting gives
W.E. 8.11 Using the van der Waals equation (on p. 376 in Chemistry3)
Work out the percentage reduction in V due to the term nb and compare it to
the percentage reduction in p due to the term a(n/V)2. Which correction
factor makes the larger change?
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Strategy
Work out the percentage reduction in V due to the term nb and compare it to
the percentage reduction in p due to the a(n/V)2 term.
Solution
The term in b increases the volume by a factor of
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Answers to boxes
Strategy
Apply the ideal gas equation, Equation 8.5, to calculate the amount of gas
required. Use the stoichiometry of the reaction that produces the N2 gas that
expands the air bag to calculate the amount of NaN3 required. Then use the
molar mass of NaN3 to determine the mass of solid required.
Solution
(a) In order to apply the ideal gas equation, we must first convert the value
given for the pressure to SI units of pascals using the conversion factor listed
in Table 8.1
We must also remember to convert the volume from units of dm3 to m3,
where 1 dm3 ≡ 10–3 m3, so that 60 dm3 ≡ 60 × 10–3 m3. Rearranging
Equation 8.5, and substituting then gives
(b) The stoichiometry of the chemical equation for the production of N2 gas
from solid NaN3
shows that every 1 mol of N2 that is produced requires 1.5 mol of solid NaN3.
The amount of NaN3 required is therefore
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Box 8.3 Measuring the distribution of speeds in a gas (on p. 364 in Chemistry3)
Why must the apparatus be contained in a sealed vessel at low pressure?
Solution
A sealed vessel ensures that it is only molecules from the sample gas that are
reaching the detector, and a low pressure reduces the number of
intermolecular collisions between gas molecules, which would otherwise
affect their speed.
Strategy
Use Equation 8.21, which is a statement of Graham’s law that shows how the
relative rate of effusion depends upon the molar mass.
Solution
The molar masses of the two different isotopomers of UF6 are
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
1/2 1/2
Rate of effusion of 239UF6 𝑀235UF6 349.00 g mol−1
= ( ) =( ) = 0.994
Rate of effusion of 235UF6 𝑀239UF6 353.00 g mol−1
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
1. 3.036 g of a gas occupy a volume of 426 cm3 at 273 K and 1.00 atm pressure.
Calculate the molar mass of the gas.
Strategy
Use the ideal gas equation to determine the amount of gas present. Calculate
the molar mass from the amount and mass of gas.
Solution
In order to apply the ideal gas equation, all values should be expressed in SI
units without prefixes. A volume of 426 cm3 is equivalent to 426 × 10–6 m3,
whilst a pressure of 1.00 atm corresponds to a 101325 Pa ≡ 101325 J m–3.
Using Equation 8.5,
Strategy
Combine the definition of density with the ideal gas equation to give an
expression for the molar mass of the gas for a given temperature, pressure
and density. Substitute the values using appropriate SI units.
Solution
Density is the ratio of mass to volume.
𝜌 = 𝑚/𝑉
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
𝑚 =𝑛×𝑀
then
𝜌 = 𝑛 × 𝑀/𝑉
and so
𝑀 = 𝜌𝑉/𝑛
But we know from the ideal gas equation, Equation 8.5, that
𝑉/𝑛 = 𝑅𝑇/𝑝
so we can eliminate the amount and volume of gas from our expression
𝑀 = 𝜌 × 𝑅𝑇/𝑝
Before we can use the expression, we must convert the values quoted to
appropriate SI units without prefixes. A density of 1.22 g dm–3 corresponds
to
Substituting gives
This suggests that the gas is ethane, which has a molar mass of
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
3. A sample of gas has a volume of 346 cm3 at 25°C when the pressure is
1.00 atm. What volume will it occupy if the conditions are changed to 35°C
and 1.25 atm?
Strategy
Rearrange Equation 8.7, which shows how pressure, volume and
temperature are related when the conditions change for a fixed amount of
gas.
Solution
𝑝1 𝑉1 𝑝2 𝑉2
=
𝑇1 𝑇2
then
𝑝1 𝑇2
𝑉2 = 𝑉1 × ×
𝑝2 𝑇1
Thus,
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
4. The air that we breathe is about 21% oxygen, by volume. Exhaled air
contains about 14% oxygen. The absorption of oxygen within the lungs
takes place in tiny spherical compartments called alveoli, which have a
diameter of the order of 0.1 mm. Estimate the number of oxygen molecules
absorbed in one breath in each of the alveoli. (Assume the body temperature
is 37°C.)
Strategy
Use the ideal gas equation to determine the amount of air contained in each
of the alveoli. Then calculate the amount of oxygen that is absorbed in each
breath knowing the proportion of air that is oxygen.
Solution
The volume of each of the spherical alveoli is
4 3 4
𝑉= π𝑟 = π × (0.1 × 10−3 m)3 = 4.2 × 10−12 m3
3 3
We know that the proportion of this gas that is absorbed is 21% – 14% = 7%
and that every mole of gas contains Avogadro’s number of molecules. The
number of oxygen molecules absorbed in each breath must therefore be
𝑁 = 7% × 𝑁A × 𝑛
= 0.07 × 6.022 × 1023 mol−1 × 1.57 × 10−5 mol
= 6.6 × 1017
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
5. Incandescent light bulbs, which have only recently gone out of use, were
filled with an inert gas to prevent the filament from burning. Find the mass
of argon needed to fill a 75 cm3 light bulb to a pressure of 1.05 atm at 25 °C.
Strategy
You can use the ideal gas equation to determine the amount of gas present in
the light bulb and then use the atomic mass to find mass of Argon gas.
Solution
Using the ideal gas equation to find the number of moles needed,
pV nRT
pV (1.05 atm 1.013105 Pa atm-1 ) (75 106 m3 )
n
RT 8.314JK 1mol1 (25 273.15)K
3.22 103 mol
6. A vessel of volume 50.0 dm3 contains 2.50 moles of argon and 1.20 moles of
nitrogen at 273.15 K.
(i) Calculate the partial pressure (in bar) of each gas.
(ii) Calculate the total pressure in bar.
(iii) How many additional moles of nitrogen must be pumped into the
vessel in order to raise the pressure to 5 bar?
Strategy
The partial pressure is the pressure that the gas would exert is alone in the
container. You can find these using the ideal gas equation. The total
pressure will be the sum of the partial pressures. One you know the
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
pressure of hydrogen that is needed then you can use the ideal gas equation
to find how many moles are needed.
Solution
For an ideal gas, the two gases act independently. Using the ideal gas
equation,
(i) For argon
pV nRT R 8.314JK 1mol1
nRT 8.314JK 1mol1 273.15K 2.50mol
p 3
1.135 105 Pa 1.135bar
V (50.0 10 m ) 3
For nitrogen
11.0 mol
Strategy
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
You can use the ideal gas equation to determine the amount of gas present
in the container. Knowing the molar masses of the two gases, the mass of
each can be found by proportion.
Solution
Using the ideal gas equation can be used to find the number of moles in the
container
pV nRT
pV (1.25 bar 1105 Pa bar -1 ) (500 106 m3 )
n
RT 8.314JK 1mol1 (25 273.15)K
0.0252mol
MR for methane is methane is 16.04 g mol-1 and for ethane is 30.07 g mol-1
so
(16.04 g mol-1 nCH4 mol) + (30.07 g mol-1 (0.0252 - nCH4 ) mol) = 0.530 g
8. Two bulbs A and B, with volumes VA = 1 dm3 and VB = 5 dm3, are connected
via a tap. The volume of the connecting tubing is negligible.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
(ii) The tap is closed and bulb B is then immersed in an oil bath at a
temperature of 423 K while the temperature of bulb A is maintained at 298
K. Calculate the resulting pressures in each bulb.
(iii) The tap is opened again. What is the final pressure and the number
of moles of gas in each bulb?
Strategy
(i) You can use Boyle’s law since the temperature and number of moles
are constant. (ii) Now we have constant volume but changing temperature
so can use Charles’ Law for the hot bulb. (iii) The ideal gas equation can be
used to find the total amount of gas present. Knowing the molar masses of
the two gases, the mass of each can be found by proportion.
Solution
(i) Applying Boyle’s law since the temperature and number of moles are
constant
p1V1 p2V2
6 bar 1 dm3 p2 / bar (1 5) dm3
p2 1 bar
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
p1 p2
T1 T2
1 bar p2 / bar
298K 423 K
p2 = 1.42 bar
(iii) Now, when the tap is opened, the pressure will equalise through
the system. Say the number of moles in each bulb are nA and nB in bulbs A
and B respectively. We can work out the number of moles of gas in the
system from the data in (i).
pV nRT
pV (6 105 Pa ) (1103 m3 )
n
RT 8.314JK 1mol1 298K
0.24 mol
If the tap is opened, the pressure in both bulbs must be equal so pA = pB.
From the ideal gas equation,
p A pB
p
nRT n RT n RT
so A A B B
0.24 nA RTB
V VA VB VB
nA 8.314JK 1mol1 298K 0.24 nA 8.314JK mol 423K
1 1
(1103 m3 ) (5 103 m3 )
2.5 106 Jm -3 nA 0.24 nA 7.0 105 Jm -3
2.5 106 Jm -3 nA 1.69 105 Jm-3 (7.0 105 Jm-3 nA )
nA 0.05mol
nB 0.24 nA mol 0.24mol 0.05mol 0.19mol
We can find the pressure from the values in either bulb (since the pressures
must be the same)
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Estimate the volume of gas that comes out of solution when a diver who
has 4.5 kg of blood rapidly ascends from a depth of 50 m of water to the
surface. Assume the solubility of nitrogen in blood is the same as in water.
Strategy
From the data, you can calculate the total amount of nitrogen dissolved in
the diver’s blood at 50 m depth. Comparing this with the amount that
dissolves at the surface gives the amount that comes out of the blood which
can be converted to a volume using the ideal gas equation.
Solution
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
When the diver ascends, the amount of N2 coming out of solution is 292.5
mg – 58.5 mg = 234.0 mg.
This can be converted to a gas volume using the ideal gas equation
pV nRT
nRT (7.31103 mol) 8.314JK 1mol1 (37 273.15)K
V
p (1.013105 Pa )
1.86 104 m3
186 cm3
10. A mixture of nitrogen and carbon dioxide contains 38.4% N2 by mass. What
is the mole fraction of nitrogen in the mixture? If the total pressure is
1.2 atm, what is the partial pressure of each gas in Pa?
Strategy
Calculate the molar masses of nitrogen and carbon dioxide and hence
determine the mole fraction of each in the gas. Use Dalton’s law to deduce
the partial pressures.
Solution
The proportion of N2 by mass is
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
𝑚N 2 𝑚N 2
=
𝑚total 𝑚N2 + 𝑚CO2
𝑛N2 𝑀N2
=
𝑛N2 𝑀N2 + 𝑛CO2 𝑀CO2
1
= = 0.384
1 + (𝑛CO2 /𝑛N2 )(𝑀CO2 /𝑀N2 )
Rearranging,
and
But
so that
𝑛 N2 1
𝑥N2 = =
𝑛N2 + 𝑛CO2 1 + (𝑛CO2 /𝑛𝑁2 )
so that substituting for the ration of the amounts of the two species gives
𝑛 N2 1 1
𝑥N2 = = = = 0.495
𝑛N2 + 𝑛CO2 1 + (𝑛CO2 /𝑛𝑁2 ) 1 + 1.02
The mole fraction of carbon dioxide is
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
11. How much faster is the rate of effusion of helium than carbon dioxide, when
both gases are at the same temperature?
Strategy
Use Equation 8.21, which shows how the relative rates of effusion depend
upon the molar mass of the molecules.
Solution
The molar masses of carbon dioxide and helium are
1/2
Rate of effusion of He 𝑀CO2 1/2 44.01 g mol−1
=( ) =( ) = 3.31
Rate of effusion of CO2 𝑀He 4.00 g mol−1
Thus, helium effuses at a rate that is over three times faster than carbon
dioxide.
12. Two identical flasks contain nitrogen gas at the same pressure. Each has an
identical pin-hole. One flask is kept at 25°C while the other is heated to
125°C. Calculate the relative rates of effusion of nitrogen from the two
flasks.
Strategy
Consider how temperature affects the rate at which molecules might escape
through the pin-hole.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Solution
The rate at which molecules collide with the pin-hole depends upon their
speed. The root mean square speed is given by equation 8.19,
3𝑅𝑇 1/2
𝑐=( )
𝑀
Thus the rate at which the molecules escape is proportional to the square
root of temperature
𝑍 ∝ 𝑇 1/2
Effusion from the hotter flask, which is at a temperature T2, therefore occurs
at a rate that is (T2/T1)1/2 times faster than from the colder falsk, which is at
T1. We must remember, however, that in using this expression, the
temperatures should be expressed in kelvin, where
Thus
Effusion therefore occurs from the hotter flask at a rate that is 1.16 times
faster than from the colder flask.
13. An evacuated flask is filled with dry air and weighed. The same flask is filled
at the same temperature to the same pressure with moist air on a humid day.
Will it weigh more, less, or the same? Explain your answer.
Strategy
Apply Dalton’s law and consider the effect of changing the composition of the
gas on the total mass.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Solution
The mass of a mixture of gases is given by the sum of the masses of the
components, which depend upon the amount and molar mass of each
species. Thus
𝑚 = 𝑛1 𝑀1 + 𝑛2 𝑀2 + …
𝑚 = ∑ 𝑛𝑖 𝑀𝑖
𝑖
𝑚 = 𝑛total ∑ 𝑥𝑖 𝑀𝑖
𝑖
𝑛𝑖 = 𝑥𝑖 𝑛total
The total amount of substance is the same in both the dry and moist air
samples. The ideal gas equation, Equation 8.5, shows that if the pressure,
volume and temperature of two samples are the same, then they must
contain the same amount of substance
𝑝𝑉
𝑛=
𝑅𝑇
Dry air is made up of 78% nitrogen, N2, and 21% oxygen, O2, along with some
other minor constituents. Thus
Moist air contains water, and so the mole fractions of nitrogen and oxygen
are lower. The molar mass of water is less than that of both nitrogen and
oxygen. Moist air therefore contains a proportion of lighter molecules than
dry air. As a result, the total mass of moist air is lower than that of dry air.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Strategy
Calculate the amount of methane that corresponds to 10 g. Then consider
the stoichiometry of the equation to deduce the amount of oxygen that is
necessary to react completely. Use the idea gas equation, Equation 8.5, to
determine the volume of this amount of gas at SATP.
Solution
The molar mass of methane, CH4, is
The chemical equation shows that the amount of oxygen required for
combustion is double the amount of methane, so that
Standard ambient temperature and pressure are 298 K and 101325 Pa, so
applying the ideal gas equation, 8.5, gives
15. The average (root mean square) speed of an oxygen molecule is 425 m s–1 at
0°C. Calculate the average speed at 100°C.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Strategy
Use Equation 8.19, which expresses how the average speed of the molecules
in a gas varies with temperature.
Solution
We know from Equation 8.19 that
3𝑅𝑇 1/2
𝑐=( )
𝑀
and so
𝑐 ∝ 𝑇 1/2
If we know the average speed c1, at a temperature T1, then we may calculate
the average speed c2 at another temperature T2, since
and therefore
16. A balloon that is porous to both gases is filled with nitrogen and placed in a
box containing helium. What will happen?
Strategy
Consider the effects of both effusion and diffusion on the gases.
Solution
Effusion is the escape of molecules through a porous membrane. If the
balloon is porous, the helium and the nitrogen molecules will effuse through
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
the membrane until the composition and pressure both inside the balloon
and outside the balloon are equal. The rate of effusion is inversely
proportional to the square root of the molar mass of the molecules. Heavy
molecules therefore effuse more slowly than light molecules. The
probability of an individual helium atom effusing into the balloon is
therefore greater than the probability of an individual nitrogen molecule
effusing in the opposite direction. The absolute rate of effusion of the two
species will, however, depend upon the relative amounts of the two gases
present.
The driving force for this process is thermodynamic because entropy favours
the mixing of ideal gases. Eventually, the composition of the balloon and the
box become equal. Even at equilibrium, however, molecules still effuse
across the membrane. The helium molecules effuse more quickly than
nitrogen molecules, but the number escaping in each direction is the same.
The system is therefore at a dynamic, rather than static equilibrium.
17. The atmospheric pressure and temperature both fall as the altitude
increases. The total pressure at a height of 20 km is about 5% of that of the
Earth’s surface (that is, at sea level) and the temperature is about –55°C.
Estimate the collision frequency and the mean free path of oxygen molecules
under these conditions. (for oxygen at this temperature, the mean speed,
𝑐̅ = 380 m s −1 .)
Strategy
Use Equation 8.22 to calculate the collisional frequency.
Solution
The collisional frequency is given by Equation 8.22
𝑝
𝑍 = √2𝑁𝐴 𝑐̅𝜎 ×
𝑅𝑇
The collision cross section for oxygen is given in Table 8.3 as
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
The mean free path is related to the collisional frequency and mean speed
through Equation 8.23. Thus
18. Argon has a collision cross-section of 0.36 nm2. At 0°C, what pressure is
needed so that its mean free path becomes equal to the diameter of the
molecules?
Strategy
Calculate the diameter of an argon atom from the cross-sectional area.
Rearrange equation 8.23, using the diameter of the atoms as the value for the
mean free path.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Solution
The collision cross section may be considered as the cross-sectional area of
the atoms and is therefore related to diameter of the atoms through
𝜎 = π𝑑 2
Thus
𝑑 = √𝜎/ π
= √0.36 nm2 / π
= √0.36 × 10−18 m2 / π
= 3.4 × 10−10 m
𝑅𝑇 𝑅𝑇
𝑝= =
√2𝑁A 𝜎𝜆 √2𝑁A 𝜎𝑑
8.3145 J K −1 mol−1 × 273 K
=
√2 × 6.022 × 1023 mol−1 × 0.36 × 10−18 m2 × 3.4 × 10−10 m
= 22 × 106 J m−3 = 22 MPa
which is equivalent to
19. Suggest why there is little hydrogen or helium in the atmosphere around the
Earth or Mars, although these gases form the major constituent of the
atmosphere of huge planets such as Jupiter or Saturn.
Strategy
Consider the effect of gravity on the composition of the atmospheres of the
planets.
Solution
The atmospheres of the planets arise because gravitational attraction
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Strategy
You can find the total pressure of gas that will be lost as well as the relative
rates of effusion of the two gases. Then, you can use the ideal gas equation to
calculate the number of moles lost.
Solution
The total rate of loss of the gases is 1000 Pa day-1 so for a 10 day mission,
10000 Pa could be lost. The relative amounts of He and O2 can be calculated
from the relative rates of effusion of the two gases. The relative rates of
effusion are inversely proportional to the relative molar/atomic masses.
1 1
Hence for each 1 mol of O2 that escapes, 2.83 mol of He will escape. The
pressures of each gas that escape are therefore 2611 Pa of O2 and 7389 Pa of
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
pV
pV nRT so n
RT
pV 2611 Pa 27 m3
For O2 n 28.9 mol
RT 8.314 J K -1 mol-1 293K
pV 7389 Pa 27 m3
For He n 81.9 mol
RT 8.314 J K -1 mol-1 293K
21. (a) State (i) the ideal gas equation (ii) the Van der Waal’s equation of state.
Explain how the additional terms in the Van der Waal’s equation account for
the actual behaviour of real gases.
(b) Without performing any numerical calculations, show that, in the limit of
high temperatures and low pressures, the van der Waals and ideal gas
equations are identical.
Strategy
Quote equations 8.5 and 8.25, and compare the additional terms. Consider
the effect on the volume of the gas of high temperatures and pressures.
Simplify the Van der Waals equation in this limit.
Solution
(a) (i)
𝑝𝑉 = 𝑛𝑅𝑇
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
n
2
(ii) p a (V nb)
V
The a(n/V)2 term accounts for the intermolecular attractions in real gases,
which reduce the force with which molecules can collide with the wall of the
container. This term makes up for the slightly reduced pressure. The nb term
corrects for the fact that molecules in a real gas do have a volume, and so
there is less volume in which molecules can actually move.
(b) High temperatures and low pressures result in relatively high volumes.
We can see this most easily by rearranging the ideal gas equation, Equation
8.5,
𝑉 = 𝑛𝑅𝑇/𝑝
so that
𝑉 ∝ 𝑇/𝑝
The van der Waals equation, Equation 8.26
includes two additional terms in the volume. In the limit of high volume, the
additional term in the first bracket becomes negligible, because as V → ∞,
1/V2 → ∞. In the same way, the additional term in the second bracket also
becomes insignificant, because as V becomes so much bigger than nb,
(V – nb) → V.
22. Dry air with the following composition is used to fill a SCUBA cylinder for a
dive.
Gas Composition of dry air by volume
N2 78%
O2 21%
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Ar 1%
Strategy
Consider how partial pressure depends upon the total pressure.
Solution
(a) Using Dalton’s law, the total pressure of the air is given by the sum of the
partial pressures of the individual components
(b) The composition of air given may be rewritten in terms of mole fractions
as
𝑥N2 = 0.78, 𝑥O2 = 0.21, 𝑥Ar = 0.01
The molar percentage of each component absorbed is independent of the
total pressure, so that at 2 atm, the air still contains 21% oxygen.
𝑝O2 = 𝑥O 2 𝑝
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
(d) The calculations show that the partial pressure of oxygen is greater
underwater than at the surface, because of the increase in the total pressure.
Filling the SCUBA tank with air with a lower proportion of oxygen would
help to correct for this change.
23. A 10 dm3 SCUBA cylinder is filled with air to a pressure of 300 atm at a
temperature of 20°C (293 K).
(a) Calculate the amount, in moles of gas in the cylinder, assuming the air
behaves as an ideal gas.
(b) When the diver jumps into cold water at 278 K, the pressure gauge
shows an alarming drop in pressure. Explain the reason why and calculate
the new pressure inside the cylinder.
(c) In fact, the compressed gases do not behave as ideal gases. Explain why.
Use the van der Waals equation (for air, a = 0.137 Pa m6 mol–2 and
b = 3.7 × 10–5 m3 mol–1) to show that the amount of air in the cylinder is
115 mol. In view of your answer to part (a) above, what are the implications
of this for divers?
Strategy
Use the ideal gas equation, Equation 8.5, to determine the amount of gas in
the cylinder, remembering to convert all values to SI units. Repeat the
calculation using the van der Waals equation, Equation 8.25.
Solution
(a) We may rearrange the ideal gas equation, Equation 8.5, to give an
expression for the amount of gas
𝑝𝑉
𝑛=
𝑅𝑇
We may use the conversion factor given in Table 8.1 to convert the pressure
to SI units, so that
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
𝑉 = 10 × 10−3 m3 = 10−2 m3
so that
(b) The sudden drop in temperature causes a decrease in the pressure of the
gas because the molecules have less thermal energy. We may apply the ideal
gas equation, Equation 8.5, to determine the new pressure. If
𝑝𝑉 = 𝑛𝑅𝑇
so that
𝑝 ∝ 1/𝑇
then for constant amount and volume,
𝑝1 𝑝2
=
𝑇1 𝑇2
then
𝑇2 278 K
𝑝2 = 𝑝1 × = 300 atm × = 285 atm
𝑇1 293 K
(c) Compressed gases do not behave in an ideal way because, when the
molecules are close together, the magnitude of the attractive interactions
becomes significant and the volume taken up by the finite size of the
molecules becomes an appreciable proportion of the total volume.
The van der Waals equation, Equation 8.25, is actually a cubic equation in n.
It is thus not possible to rearrange this equation to give an expression for n.
Instead, it is simpler to assume the revised value for the amount given,
n = 115 mol, and show that this is consistent with a pressure of 300 atm.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
𝑛𝑅𝑇 𝑛 2
𝑝= − 𝑎( )
𝑉 − 𝑛𝑏 𝑉
115 mol × 8.3145 J K −1 mol−1 × 293 K 6 −1
115 mol 2
= −2 3 − 0.137 Pa m mol ( −2 3 )
10 m − 115 mol × 3.7 × 10−5 m3 mol−1 10 m
= 30.4 × 106 Pa
24. The space between the stars in the universe contains a mixture of gases at
very low pressure as well as some dust. The gas is mainly hydrogen with a
little helium, but many other molecules have also been detected in tiny
amounts (see Chapter 4, p.167). For a helium atom, the collisional cross
section = 0.21 nm2. The conditions in interstellar space are around
T = 10 K and p = 1 10–18 atm.
(a) Calculate the mean free path, , of helium atoms at SATP.
(b) Estimate the value of for helium atoms in interstellar space. (For the
atoms at 10 K, c = 230 m s–1.)
Strategy
Use Equation 8.23 to determine the mean free path under the conditions
given. Calculate the time between collisions as the reciprocal of the
collisional frequency.
Solution
A collision cross section of 0.21 nm2 is equivalent to 0.21 × 10–18 nm2,
because 1 nm2 ≡ 10–18 m2. The mean free path of the molecules within a gas
at standard ambient temperature and pressure may therefore be calculated
using Equation 8.23
𝑅𝑇
𝜆=
√2𝑁A 𝜎𝑝
8.3145 J K −1 mol−1 × 298 K
=
√2 × 6.022 × 1023 mol−1 × 0.21 × 10−18 nm2 × 101325 J m−3
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
= 137 × 10−9 m
= 137 nm
(b) In order to calculate the mean free path under the conditions in the
interstellar medium, it is not necessary to repeat the entire calculation . We
know that
𝜆 ∝ 𝑇/𝑝
so, if, in the interstellar medium, the pressure is 10–18 atm /1 atm = 10−18
times less, and the temperature 10 K / 298 K ≈ 0.034 times less, then the
mean free path may be estimated as
(c) The time between collisions is the reciprocal of the collisional frequency
𝑡 = 1/𝑍
Mean free path and collisional frequency are related through the mean speed
𝜆 = 𝑐̅/𝑍
25. Sketch graphs to show how the distribution of molecular speeds differs
between
(a) helium at 100 K and helium at 300 K
(b) helium at 100 K and xenon at 100 K
Strategy
Consider the effects of temperature and molecular mass on speed, as shown
in figures 8.12(b) and 8.12(a).
Solution
(a) <Unnumbered figure 8.1, as in back-of-book answers>
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
1
26. Using the kinetic theory of gases, it can be shown that pV = 3 nNAmc2.
Strategy
Use equation 8.14 to relate the expression given in the question to the ideal
gas equation. Think about how both the empirical and theoretical equations
are derived.
Solution
(a) p is the pressure of the gas, in Pa, V is the volume in m3, n is the number
of moles of gas, NA is Avogadro’s constant, m is the mass of a molecule and c
is the average molecular speed.
(b) The left hand side of both equations equals pV, therefore we can say that
the right hand sides equal each other, so that
1
nNAmc2 = nRT
3
1
NAmc2 = RT
3
1
EKE = mc2
2
2 EKE = mc2
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
1
pV = 3 nNA (2 EKE)
pV = constant x T
(c) The ideal gas equation is derived from experimental observations, and
introduces R as a proportionality constant.. The theoretical approach starts
off by considering the momentum of a single molecule colliding with the wall
of a container, and applies physical laws to the behaviour of molecules in an
ideal gas to rrive at an expression relating P, V and T.
dioxide, helium
(a) Which gas would be expected to most closely follow ideal behaviour?
(c) Which gas would have the highest and lowest root mean square speeds?
Strategy
Think about the assumptions made in the ideal gas equation, and what
makes a gas ‘ideal’. Look at equation 8.19 to see the relationship between
molecular mass and the root mean square speed of a gas, and equation 8.20
for the rate of effusion.
Solution
(a) For an ideal gas we assume the molecules have no volume and no
intermolecular attractions. Therefore the most ideal gas will have a small
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
volume, be non-polar and have few electrons to create weak Van der Waals
forces. Therefore helium would most closely follow ideal behaviour.
(b) A gas with large volume and strong intermolecular forces deviates from
ideal behaviour, so in this case the answer is hydrogen chloride, because its
molecules are polar and therefore have the greatest intermolecular forces.
Number of molecules 10 20 40 15 10 5
Strategy
The mean speed is the sum of the molecular speeds divided by the total
number of molecules. To find the root mean square speed, use the sum of
each molecule’s speed squared, divide by the total number of molecules, and
take the square root of the answer.
Solution
(a) The most probable speed is that which is measured most often: 100 m s-
1.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
(b) Sum the speeds of all molecules, and then divide by the total number of
molecules.
(10 x 60 m s-1) + (20 x 80 m s-1) + (40 x 100 m s-1) + (15 x 120 m s-1) + (10 x 140
m s-1) + (5 x 160 m s-1) = 10200 m s-1.
Now divide this by the total number of molecules, and take the square root of
the answer.
29. The density of nitrogen gas in a container at 300 K and 1.0 bar pressure is
1.25 g dm-3.
(a) Calculate the r.m.s speed of the molecules.
(b) At what temperature will the r.m.s speed be twice as fast?
Strategy
Use equation 8.19 to calculate the root mean square speed, being careful
with units. Look at the relationship between the root mean square speed and
temperature.
Solution
(a) The molar mass of nitrogen is 28.0 g mol-1, which is equivalent to 0.028
kg mol-1. Substituting into equation 8.19, using T = 300 K, we get
1/ 2
3RT
c
M
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
= 517 m s-1
(b) Equation 8.19 shows that the root mean square speed is proportional to
the square root of temperature. Therefore if c is twice as large, c2 is four
times greater, so the temperature would need to be four times greater, so T =
1200 K.
Strategy
Use equation 8.19 directly to find the r.m.s. speed. Calculate the collision
cross sectional area, and then use equation 8.22, converting to standard
units first. Use the root mean square speed and the collision frequency to
find the mean free path.
Solution
(a) The value of M for UF6 is 352 g mol-1 = 0.352 kg mol-1. Substituting this
into equation 8.19 gives:
1/ 2
3RT
c
M
c = 146 m s-1
𝜎 = 𝜋 d2
= 5.03 x 10-19 m2
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Substitute this value into the equation for collision frequency. Note that 1 bar
= 1 x 105 Pa, and so 0.1 x 10-3 bar = 10 Pa
λ=c/Z
= 5.8 x 10-4 m
31. (a) Explain how the fact that gases such as nitrogen or carbon dioxide can be
liquefied by applying high pressure shows that the ideal gas equation can
only be an approximation.
(b) Why is a lower pressure needed to liquefy CO2 than for N2?
Strategy
Consider the intermolecular forces in gases and liquids, and the assumptions
made about them in the ideal gas equation. What is required to liquefy a gas?
Solution
(a) The fact that a gas can be liquefied shows that there are intermolecular
forces between gas molecules. If this were not the case, as assumed in the
ideal gas equation, it would not be possible to liquefy the gas.
(b) CO2 is a less ‘ideal’ gas than N2. It has a larger mass and contains polar
bonds, therefore there are greater Van der Waals forces between molecules
of CO2 than between molecules of N2. If there are more intermolecular
attractions, it will be easier to liquefy the gas by compression.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
32. Predict which of the following substances will have (i) the highest and (ii)
the lowest values of the van der Waals constants 'a' and 'b'.
Strategy
Consider what each of the terms represents and relate them to the
molecular properties of the molecules of the three gases.
Solution
The value of 'b' is related to the actual volume occupied by the molecules
and hence the molecular size. He is the smallest of the three molecules (so
the lowest 'b') while NO2 is the biggest and so has the highest 'b' value.
Strategy
You can substitute the data into both the ideal gas equation and van der
Waals’ equation, remembering to perform any relevant unit conversions to
maintain consistency.
Higher Education
© Oxford University Press, 2017. All rights reserved.
3
Solutions manual for Burrows et.al. Chemistry Third edition
Solution
pV
pV nRT so T
nR
n
2
p a V nb
V
T
nR
20 mol
2
120 atm 0.034 dm 6
atm mol -2
10 dm3 10 dm 20 mol 0.024 dm mol
3 3
-1
T 697K
20 mol 0.08206 dm3 atm K -1mol 1
Higher Education
© Oxford University Press, 2017. All rights reserved.