Professional Documents
Culture Documents
D
LA
Question asked (9):
What type of heat exchanger is shown in the illustration?
Selected answer (score 0):
Don't know
Correct answer:
Plate
What would you do if you are told to operate a piece of mechanical equipment which you
are not familiar with?
Selected answer (score 0):
Don't know
AR
Correct answer:
Seek advice from your superior before attempting to operate it.
Page 1/11
Wrong answer summary
D
To remove any accumulated sludge from the water drum.
LA
While trying to deballast a double bottom tank problems are encountered getting suction
on the ballast pump, a centrifugal pump mounted above the tank top. What action can be
taken to solve the problem?
Selected answer (score 0):
Don't know
Correct answer:
Prime the pump with seawater from the main inlet valve.
In case of a fire inside the Acetylene-line in the ac/ox gas welding equipment, what action
is deemed necessary?
Selected answer (score 0):
Don't know
AR
Correct answer:
Close the valves on both the Acetylene and the Oxygen bottles.
Page 2/11
Wrong answer summary
D
Exhaust valve
LA
What is the correct name of the tool shown in the illustration?
Selected answer (score 0):
Don't know
Correct answer:
Adjustable wrench
Don't know
Correct answer:
"Stand By" means that the engineers should be ready to respond to bridge requirements.
AR
Correct answer:
Go to your lifeboat station
Page 3/11
Wrong answer summary
D
Use a rope ladder close to the raft to climb down and board
LA
Question asked (3742):
What kind of safety equipment should be used when operating a grinding wheel?
Selected answer (score 0):
Don't know
Correct answer:
Goggles and shield
What is the most common fixed fire fighting extinguishing system fitted in an engine
room?
Selected answer (score 0):
Don't know
AR
Correct answer:
A carbon dioxide (CO2) system
Page 4/11
Wrong answer summary
D
All the mentioned alternatives
LA
We must clean the spots of oil on hot surfaces because:
Selected answer (score 0):
Don't know
Correct answer:
all the answers are correct
Don't know
Correct answer:
Use a rope ladder close to the raft to climb down and board
Page 5/11
Wrong answer summary
D
It lessens the survivor's heat escape
LA
When mustered to an abandon ship drill, what is the first thing you do when entering the
muster station?
Selected answer (score 0):
Don't know
Correct answer:
Put on a life jacket
Correct answer:
Particulate detector
Page 6/11
Wrong answer summary
D
Correct answer:
Use cleaning wires starting with a small gauge and gradually work up to the full size of
the nozzle hole.
LA
Question asked (32428):
One of the two water level gauge glasses on the high pressure boiler steam drum has
started leaking quite heavily. What action, from the options given, should the boiler watch
rating take?
Selected answer (score 0):
Don't know
Correct answer:
PA
Inform the Officer of the watch immediately so that arrangements can be made to replace
the leaking glass.
G
Question asked (32515):
What is the most likely cause of black smoke at the boiler exhaust during normal
operation of a steam boiler?
Selected answer (score 0):
N
Don't know
Correct answer:
Insufficient combustion air.
IA
the burner has failed to light following a drop in steam pressure. What action should be
taken?
Selected answer (score 0):
Don't know
Correct answer:
Call the duty engineer immediately using the engineers call alarm.
M
Page 7/11
Wrong answer summary
An engine room rating is assisting the duty engineer during a period of UMS operation.
After completing the tasks they leave the engine room which is returned to UMS mode.
The rating realises that an oil tank filling valve has been left open. What action should be
taken?
Selected answer (score 0):
Don't know
Correct answer:
Inform the duty engineer immediately so that the engine room can be re-entered and the
D
valve can be shut.
LA
Question asked (32522):
The engine rating on watch finds the level of the diesel engine jacket water header tank
well below normal. After topping up the tank and checking around the engine, a leak is
found. What action should be taken?
Selected answer (score 0):
Don't know
Correct answer:
PA
Try and quickly stop the leak and then inform the engineer on watch of what has
happened.
Don't know
Correct answer:
Stop all of the ballast pumps and close all of the ballast valves as soon as operations are
IA
stopped. Ballast lines should always be closed except when they are being used.
An engine room rating is given the task of retightening the flanges of a pipe that has been
replaced in the engine room. Which of the following tightening procedures should be
followed?
Selected answer (score 0):
Don't know
Correct answer:
Gradually tighten all of the bolts working diagonally across and around the flange.
M
Page 8/11
Wrong answer summary
Following repair and refitting of the seawater pipe for the fresh water generator feed line
the rating notices that one of the flange joints is leaking. What action should be taken?
Selected answer (score 0):
Don't know
Correct answer:
Check the bolts are correctly tightened before informing the engineer so that the flange
faces can be cleaned and re-jointed if necessary.
D
Question asked (32613):
While getting tools ready and preparing for overhaul work on the main engine the engine
LA
room rating notices that the electrical extension is damaged. A small section of the cables
outer insulation is split although the inner insulation appears ok. What action should the
rating take?
Selected answer (score 0):
Don't know
Correct answer:
a replacement extension.
An engine room rating is assisting in the maintenance of some of the valves on the low
pressure steam range. Which packing material, from the options given, would be the best
G
choice for repacking the gland of a low pressure steam valve?
Selected answer (score 0):
Don't know
Correct answer:
N
Don't know
Correct answer:
Coat the threads in graphite based grease.
Which tool would be best suited for cutting a piece of angle iron?
Selected answer (score 0):
Don't know
Correct answer:
Hacksaw.
Page 9/11
Wrong answer summary
D
Correct answer:
A set of feeler gauges.
LA
Question asked (33071):
Which of the options given is most likely to result in overheating of a ball bearing fitted to
a pump shaft?
Selected answer (score 0):
Don't know
Correct answer:
Completely filling the bearing with grease.
Don't know
Correct answer:
The Starboard quarter is C, in the figure
Page 10/11
Wrong answer summary
D
If I saw a person falling overboard I would shout repeatedly, "Man overboard"
LA
What is the most important treatment concerning a foreign body in the eye?
Selected answer (score 0):
Don't know
Correct answer:
Rinsing of the eye with water
Don't know
Correct answer:
Ready for immediate use
AR
Correct answer:
Plugged to prevent spilled oil flowing overboard
Page 11/11