Professional Documents
Culture Documents
KENLAYER Example PDF
KENLAYER Example PDF
To set up a new data file click 'File' and 'New' and the filename 'Untitled' will appear on the label
beneath 'File'. You can now proceed to input the necessary data.
TITLE: Enter any descriptive title of 68 characters or less. Commas are not allowed.
MATL: Enter “1” if all of the materials we’ll be using are linear elastic.
NDAMA: Enter “0” since we don’t want to do a damage analysis at this time. Later on, we may
change this to “1” to determine how many load applications are needed to cause failure.
NPY: Enter “1” since we will not be using seasonally-varying layer moduli. Eventually, we’ll use
moduli that vary throughout the year based on seasonal changes in temperature and moisture.
NLG: Enter “1” because we will only have one load group. You can have as many as 12 different
load groups. A load group consists of either a single wheel load, a dual wheel load, a tandem axle
load, or a tridem axle loaf.
DEL: Leave at the default of 0.001, which implies a numerical integration accuracy of 0.1%.
NL: Enter “2” because “1” doesn’t work. KENLAYER models the pavement system as one or
several material layers overlying a semi-infinite halfspace. You must have at least one layer in
addition to the halfspace, so two is the minimum number of layers you can have. You can have up
to 19 different pavement layers.
NZ: Enter “1” because we’re only going to request stress and deflection outputs at just one depth.
You can obtain output at as many as 19 different depths.
ICL: Leave at 80. If the program doesn’t converge on a solution within 80 iteration, it stops.
NSTD: Enter “5” to output vertical displacements and stresses. You can also choose “1” to output
only vertical displacements or “9” to output vertical displacements, stresses, and strains.
NBOND: Leave at “1” to use fully frictional layer interfaces. You could also choose “2” if one
ore more interfaces are to be frictionless.
NLBT: Leave at “1” since we’re not doing a damage analysis. This entry specifies the number of
layers for which a damage analysis will be performed based on the tensile strain at the bottom of
the layer (which contributes to fatigue failure).
NLBT: Leave at “1” since we’re not doing a damage analysis. This entry specifies the number of
layers for which a damage analysis will be performed based on the compressive strain at the top
of the layer (which contributes to rutting failure).
NUNIT: Leave at “0” for English units. You can also set it to “1” for SI units.
Upon completion, click the 'OK' button to return to the Main Menu of LAYERINP.
TH: Enter the thickness of each material layer in inches. The last layer is infinite in thickness and
need not be specified.
PR: Enter “0.5” for incompressible materials. Suggested values are 0.35 for asphalt and granular
materials and 0.45 for fine-grained soils.
After typing the data in a cell, be sure to press “Enter” or the up or down arrow key to make it
effective.
You can delete a line (layer) by first clicking anywhere on the line to make it active, then pressing
<Ctrl><Del>. The NL in the 'General' menu will be reduced automatically by 1.
You can add a new line (layer) above any existing line (layer) by first clicking the cell in the
existing line to make it active, then pressing <Ctrl><Ins>. A blank line will appear for you to
enter the necessary data. The NL in the 'General' menu will increase automatically by 1.
After completing this form, click 'OK' to return to the Main Menu of LAYERINP.
Step 7: Click on “Moduli” on the toolbar
Upon completion, click the 'OK' button to return to the Layer Modulus of Each Period.
LOAD: Enter “0” for a single axle with a single tire (i.e., one contact patch). Other possible
choices are “1” for a single axle with a dual wheel (two contact patches), “2” for tandem axles
with dual wheels (four contact patches), and “3” for a tridem axle with dual wheels (six contact
patches). See Figure 3.8 in the textbook.
CR: Enter “6.01” for the radius of the contact patch (in inches).
YW: Enter “0” since there is only one contact patch. This is the center-to-center spacing between
the two dual wheels. See Figure 3.8 in the textbook.
XW: Enter “0” since there is only one axle. This is the center-to-center spacing between the axles.
See Figure 3.8 in the textbook.
NR or NPT: Enter “6” for the number of points in the horizontal plane at which you want outputs.
You can delete a line (layer) by first clicking anywhere on the line to make it active, then pressing
<Ctrl><Del>. The NL in the 'General' menu will be reduced automatically by 1.
You can add a new line (layer) above any existing line (layer) by first clicking the cell in the
existing line to make it active, then pressing <Ctrl><Ins>. A blank line will appear for you to
enter the necessary data. The NL in the 'General' menu will increase automatically by 1.
After completing this form, click 'OK' to enter the auxiliary form where you enter the coordinates
of the output points.
RC: Enter the radial offset for each of the 6 output locations (0, 12, 24, 36, 48, 60) in inches.
After completing this form, click 'OK' to return to the load information form, then click 'OK' to
return to the Main Menu of LAYERINP.
Name it “Problem4” or something like that. Since this program is DOS-based, you probably can’t
use file names with embedded spaces or filenames with more than 8 characters (not counting the
file extension, which will always be “.dat”).