This document outlines quality assurance provisions for various types of grommets and washers. It specifies that the contractor is responsible for inspection to ensure items meet all requirements. Testing must be done in accordance with various standards for finishes like cadmium plating, black enamel, and anodic coatings. Rolled rim grommets and spur type washers must be stamped with size numbers, while other items cannot have any marks. Items must be uniform and free from defects affecting performance.
This document outlines quality assurance provisions for various types of grommets and washers. It specifies that the contractor is responsible for inspection to ensure items meet all requirements. Testing must be done in accordance with various standards for finishes like cadmium plating, black enamel, and anodic coatings. Rolled rim grommets and spur type washers must be stamped with size numbers, while other items cannot have any marks. Items must be uniform and free from defects affecting performance.
This document outlines quality assurance provisions for various types of grommets and washers. It specifies that the contractor is responsible for inspection to ensure items meet all requirements. Testing must be done in accordance with various standards for finishes like cadmium plating, black enamel, and anodic coatings. Rolled rim grommets and spur type washers must be stamped with size numbers, while other items cannot have any marks. Items must be uniform and free from defects affecting performance.
TypeII, Class2 (.00030thick)in accordance withGQ-P-416. 3.4.3 Blackenamelfinish. Blackenamelfinishshallbe ClassB, in accordance withTT-E-4U9. 3.4.4 Blackchemicalfinishfor mpper alloys. Blackchemicalftiish shallbe in accordance withMIL-F-495. 3.4.5 Anodiccoatingsfor aluminunand aluminm alloys. Anodiccoating, TypeZ, Class2 shallbe in accordance withMIL-A-8b25. 3.4.6 Phosphatecoating(forferrousmetals).Phosphatecoatingshallbe in accordance withmD-P-16232. 3.4.7 zincplating.Zincplatingshallbe TypeII, ClassFe/Zn5 in accordance withASTMBb33. 3.5 Marking. All rolledrim grommetsend spurtypewashersshallhavethe sizenmber stampedon the face. The surfaceoppositethesestampmarksshall showno signsof penetrationor uneveneaaand stamptigshallnot cause distortion. All other types of grcmmet.s and tia.shersshall be clear of size numbersor marksof any kind. 3.6 Worbnanshi~:.The grcssmtshellbe uniformin qualityand shallbe freefromirregularities or defectswhichcouldadverselyaf feetperformance, reltibility or durability. 4. QUALITYASSURANCEPROVISIONS 4.1 Responsibility for Unless inspection. otherwise specifiedin the cent ract or purchase ractoris responsible order, the cent for the performance of all inspectionrequirementsas specifiedherein. Exceptas otherwise specifiedin the contractor purchaseorder,the contractor may use his own or any otherfacilities suitablefor the performance of the inspection requirementsspecified herein,unlessdisapproved by the Government.The Governmentreservesthe rightto performany of the inspections set fmth in the specif ication wheresuchinspections are deemednecessaryto assure suppliesad servicesconformto prescribed requirements. 4.1.1 Responsibility for compliance.All itemsmustmeetall requirements of sections3 and 5. The inspectionset forthin thisspecification shall be.- a &, of the contractor’ e overall tispect ion eys~em or quality program. The absenceof any Inspectionrequirementsin the specification shall not relievethe contmctorof the responsibilityof assuringthatall products or suppliessubmitted to the Governmentforacceptancecomplywithall requirementsof the contract.Samplingh qualityconfonmncedoesnot authorizesubmission of Imowndefectivematerial,eitherindicated or actual, nor doesit ccfsmittheGovernment to acceptance of defectivemsterial.
Central Marks Department-Iii Our Ref: CMD-III/16:15490 30 Oct 2006 Subject: Sulphide Stress Cracking Resistance Test On CNG Cylinders As Per Is 15490:2004