Professional Documents
Culture Documents
WARNING Introduction
Type 95LD and 95HD are small-size, large-capacity, differ-
ential pressure regulators. They are suitable for steam, air,
Regulators should be installed, operated, gas, oil, water, and other fluids control. Typical applications
and maintained in accordance with federal, include use on testing fixtures, wash tanks, sterilizers,
state, and local codes, rules and regula- steam tables, fuel lines, and plant air supplies. The differen-
tions, and Fisher instructions. tial pressure range of the Type 95LD regulator is from 2 to
30 psi (three spring ranges). The Type 95HD differential
pressure range is from 15 to 150 psi (seven spring ranges).
If the regulator vents gas or a leak develops
in the system, it indicates that service is re-
quired. Failure to take the regulator out of
service immediately may create a hazard-
ous condition. Installation
Before installing the regulator, be sure the chosen location
is adequately protected from damage by vehicles and other
Call a serviceman in case of trouble. Only a external sources. The regulator should be away from build-
qualified person must install or service the ing eaves and above probable snow levels. Temperature
regulator. conditions should not exceed the limits shown in table 1.
Table 1. Specifications
Approximate Weight
End Connection Style Type 95HD
1/4-inch body: 4 lb (1.8 kg)
NPT screwed, ANSI flanged-14 inches face to face 1/2-inch body: 8 lb (3.6 kg)
(DIN flanged-356mm face to face), or SWE 3/4 and 1 inch bodies: 20 lb (9.1 kg)
1-1/2 and 2-inch bodies: 73 lb (33.1 kg)
Type 95LD
Maximum Pressures(1)(2) 1/4-inch body: 6 lb (2.7 kg)
1/2-inch body: 12 lb (5.4 kg)
See table 2 3/4 and 1-inch bodies: 32 lb (14.5 kg)
1. Relief pressure setting plus maximum allowable buildup.
2. The pressure/temperature limits in this bulletin and any applicable standard
limitation should not be exceeded.
Unpack the regulator and remove the protective shipping of pressure-containing parts or explosion of
plugs from the end connections of the body and the pres- accumulated gas. The system should be in-
sure connection in the spring case. Be sure the body and spected after any overpressure condition.
connecting pipelines are clean. Coat the pipeline threads
with a suitable pipe compound. The regulator may be As is the case with most regulators, Types 95LD and 95HD
installed in any position as long as the flow is in the direction have outlet pressure ratings that are lower than the inlet
indicated by the arrow cast on the body. pressure ratings. Some type of overpressure protection is
needed if the actual inlet pressure can exceed the outlet
The design of the regulator isolates the diaphragm and the pressure rating. Common methods of overpressure protec-
pressure response chamber from the main flow steam. Re- tion include relief valves, monitoring regulators, or series
duced pressure registers under the diaphragm through the regulation.
pitot tube or registration hole. Loading pressure registers on
the top of the diaphragm. The loading pressure is con- The maximum pressures that should not be exceeded are
nected to the NPT connection in the spring case. stamped on the nameplate and also shown in table 2.
Adjustment
The regulator is factory-set for the differential pressure spe-
Overpressure Protection cified on your order. The spring range is stamped on the
nameplate. If a pressure setting beyond this range is neces-
sary, substitute an appropriate spring. Be sure to change
WARNING the nameplate to indicate the new spring range.
2
Types 95LD and 95HD
Table 3. Spring Part Numbers for 95 Series Body Sizes and Pressure Ranges
OUTLET OR
DIFFERENTIAL SPRING PART
TYPE BODY SIZE, PRESSURE NUMBER AND
NUMBER INCHES RANGE(1) COLOR
Psig Bar
2 to 6 0.1 to 0.4 1E392527022 Yellow
1/4 5 to 15 0.3 to 1.0 1E392627012 Green
13 to 30(2) 0.9 to 2.0(2) 1E392727142 Red
2 to 6 0.1 to 0.4 1E395627022 Yellow
95LD 1/2 5 to 15 0.3 to 1.0 1D745527142 Green
13 to 30(2) 0.9 to 2.0(2) 1E395727192 Red
2 to 6 0.1 to 0.4 1E398927022 Yellow
3/4, 1 5 to 15 0.3 to 1.0 1E399027142 Green
13 to 30(2) 0.9 to 2.0(2) 1E399127162 Red
15 to 30(2) 1.0 to 2.0(2) 1E392527022 Yellow
1/4 25 to 75 1.7 to 5.2 1E392627012 Green
70 to 150 4.8 to 10.3 1E392727142 Red
15 to 30(2) 1.0 to 2.0(2) 1E395627012 Yellow
1/2 25 to 75 1.7 to 5.2 1D745527142 Green
70 to 150 4.8 to 10.3 1E395727192 Red
95HD 15 to 30(2) 1.0 to 2.0(2) 1E398927022 Yellow
3/4, 1 25 to 75 1.7 to 5.2 1E399027142 Green
70 to 150 4.8 to 10.3 1E399127162 Red
5 to 80 0.3 to 5.5 1E795327082 Light Blue
60 to 120 4.1 to 8.3 1E795427082 Light Gray
1-1/2, 2
100 to 140 6.9 to 9.7 1E793327082 Yellow
120 to 150 8.3 to 10.3 1D788827082 Black
1. Pressure ranges given for Types 95L and 95H regulators indicate actual outlet pressure. For Types 95LD and 95HD regulators, the
pressure ranges indicate the differential pressure that can be obtained with the indicated spring. The differential pressure (spring
setting) is added to the spring case loading pressure to determine the actual outlet pressure.
2. Type 95H is recommended where close regulation is not required. Type 95L is recommended where close regulation is required.
3
R
Types 95LD and 95HD
Due to normal wear and damage that may occur from exter-
nal sources, the regulator should be inspected periodically.
Parts such as the O-rings, gaskets, diaphragm, and pack-
ing should be replaced as necessary. The frequency of in-
spection and replacement depends upon the severity of
service conditions or the requirements of state and federal
laws.
VALVE STEM
PITOT TUBE Refer to figure 4 or 5 while disassembling the regulator. The
regulator does not have to be taken out of the pipeline to be
ORIFICE
disassembled. Relieve the spring compression by turning
VALVE PLUG
the handwheel (key 38) counterclockwise.
VALVE PLUG
SPRING
W0078*
4
Types 95LD and 95HD
follower onto the adjusting screw and into the packing box.
Screw on the packing nut.
6. Put the packing box back onto the spring case. Set the
handwheel and washer on the adjusting screw and screw
in the machine screw.
Replacement of Diaphragm
When the regulator does not respond to differential pres-
sure changes or the loading pressure seems to leak to the
downstream piping, the diaphragm could be worn out or
AL2517
ruptured. Inspect the diaphragm as follows:
A1746-1
b. Take the valve plug or orifice and move it in a ‘‘figure 2. Take the upper spring seat (key 9), regulator spring (key
8’’ motion on the lapping compound. Do not allow the part 11) and the lower spring seat (key 8, Type 95HD) out of the
to tip or rock since this would round the corners. lower spring case. In Type 95LD, the lower spring seat and
diaphragm plate (key 21) are screwed together and can be
c. Repeat step b for each part, using an 800-grit or removed as one unit.
1000-grit silicon carbide or aluminum oxide lapping com-
pound.
3. Replace the diaphragm (key 12) and the diaphragm gas-
d. Wash away all traces of the lapping compound. To ket (key 19, Type 95HD only). Note that if the diaphragm
help prevent scratching the seating surfaces, a light coat of material is metal, two diaphragms are used together.
oil may be applied before returning the valve plug and orifice
to the body. 4. Set the diaphragm plate, lower spring seat, spring, and
upper spring seat back onto the diaphragm.
4. Return the orifice, valve plug, valve plug spring, and
valve plug guide to the body. 5. Place the spring case on the body. Screw in the cap
screws finger-tight only.
5
R
Types 95LD and 95HD
3* Orifice (cont’d)
Composition Seat
Key Description Part Number
1/4-inch body
Brass 1E3932 14012
Parts Kit (Included are keys 3, 4, 10, 12, 416 SST 1E3932 35132
and 19) 1/2-inch body
Type 95HD Brass 1E3962 14012
For Composition, Trim 2 416 SST 1E3962 35132
1/4-inch body R95HX 000012 NACE, 316 stainless steel/
1/2-inch body R95HX 000022 fluoroelastomer 1E3962 35072
3/4 and 1-inch body R95HX 000032 3/4 and 1-inch body
For Composition, Trim 3A Brass 1E3995 14012
1/4-inch body R95HX 000102 416 SST 1E3995 35132
1/2-inch body R95HX 000112 NACE, 316 stainless steel/
3/4 and 1-inch body R95HX 000122 fluoroelastomer 1E3995 35072
1-1/2 and 2-inch body R95HX 000042 1-1/2 and 2-inch body
For Metal Trim (Type 95HD only)
1/4-inch body R95HX 000052 416 SST 1P7860 35132
1/2-inch body R95HX 000062 4* Valve Plug
3/4 and 1-inch body R95HX 000072 Metal-to-metal seat, 416 SST
1-1/2 and 2-inch body R95HX 000082 1/4-inch body 1E3917 46172
Extra parts for 1-1/2 and 2-inch body 1/2-inch body 1E3951 46172
include keys 45, 47, 51 and 52 3/4 and 1-inch body 1E3981 46172
Type 95LD 1-1/2 and 2-inch body
For Composition, Trim 2 (Type 95HD only) 1U4037 46172
1/4-inch body R95LX 000012 Composition Seat
1/2-inch body R95LX 000022 1/4-inch body
3/4 and 1-inch body R95LX 000032 Brass/neoprene 1E3933 000C2
For Composition, Trim 3A SST/neoprene 1E3933 000E2
1/4-inch body R95LX 000102 1/2-inch body
1/2-inch body R95LX 000112 Brass/neoprene 1E3963 000A2
3/4 and 1-inch body R95LX 000122 SST/neoprene 1E3963 000B2
For Metal Trim NACE, 316 stainless steel/
1/4-inch body R95LX 000042 fluoroelastomer 1E3963 X0082
1/2-inch body R95LX 000052 3/4 and 1-inch body
3/4 and 1-inch body R95LX 000062 Brass/neoprene 1E3996 000A2
SST/neoprene 1E3996 000B2
1 Body See following table NACE, 316 stainless steel/
2 Spring Case fluoroelastomer 1E3995 35072
Type 95HD 1-1/2 and 2-inch body
Cast iron SST/nitrile 1U4039 000A2
1/4-inch body 2L4431 19012
1/2-inch body 2H8422 19012 5 Valve Plug Guide
3/4 and 1-inch body 3L4573 19012 Metal-to-metal seat, 416 SST
1-1/2 and 2-inch body 42A050 1X012 1/4-inch body
Steel Brass 1E3918 14012
1/4-inch body 2L4432 22012 1/2-inch body
1/2-inch body 2L3241 22012 Brass 1E3952 14012
3/4 and 1-inch body 3E4088 22012 3/4 and 1-inch body
1-1/2 and 2-inch body 31A980 4X022 Brass 1E3982 14012
Stainless Steel 1-1/2 and 2-inch body
1/4-inch body 2L4432 33092 416 SST 1U4041 35132
Type 95LD Composition Seat
Cast iron 1/4-inch body
1/4-inch body 2L4433 19012 Brass 1E3918 14012
1/2-inch body 3H7764 19012 416 SST 1E3918 35132
3/4 and 1-inch body 4H3459 19012 1/2-inch body
Steel Brass 1E3952 14012
1/4-inch body 2L4434 22012 416 SST 1E3952 35132
1/2-inch body 3L3242 22012 NACE, 316 stainless steel/
3/4 and 1-inch body 4F4323 22012 fluoroelastomer 1E3952 35072
3* Orifice 3/4 and 1-inch body
Metal-to-metal seat, 416 SST Brass 1E3982 14012
1/4-inch body 1E3916 46172 416 SST 1E3982 35132
1/2-inch body 1E3950 46172 NACE, 316 stainless steel/
3/4 and 1-inch body 1E3980 46172 fluoroelastomer 1E3982 35072
1-1/2 and 2-inch body 1-1/2 and 2-inch body
(Type 95HD only) 2P7870 46172 416 SST 1U4041 35132
6
Types 95LD and 95HD
N.S. - NEVER-SEEZ
TRADEMARK OF NEVER-SEEZ COMPOUND CORP.
30A6999-A
20 Pitot Tube PARTS NOT SHOWN 13, 18, 30, 31, 45, 54
3/4 and 1-inch body
N.S. - NEVER-SEEZ
Copper 1E3994 17012 TRADEMARK OF NEVER-SEEZ- COMPOUND
NACE, 316 stainless steel/ CORP.
fluoroelastomer 1E3994 38092 30A7023-A
B0876-1
1-1/2 and 2-inch body Figure 5. Type 95HD Regulator Assembly Drawing
SST 1P7856 38072
21 Diaphragm Head Ass’y, aluminum/steel
Type 95LD only
Key Description Part Number
1/4-inch body 1E3936 X0012
1/2-inch body 1E3967 X0012 34 Packing Follower (Continued)
3/4 and 1-inch body 1E3907 X0012 1/2 thru 2-inch body
30 Pusher Post, 416 SST, Type 95HD only Steel 1K8849 24092
Metal-to-metal seat 1P7851 35132 35 Packing Box Nut
Composition seat 1P7849 35132 Steel Cd pl 0P0776 24102
31 Locknut, steel Cd, Type 95HD only 1P7887 24122 36* Packing, TFE (3 req’d)
32 Packing Box, steel 1/4-inch body 1C7526 01012
1/4-inch body 1L4496 24092 1/2 thru 2-inch body 1H7843 01012
1/2 thru 1-inch body 1L3240 24092 37* Packing Box Gasket, steel/composition
1-1/2 and 2-inch body 11A980 9X022 1/4-inch body 1B4870 99202
33 Adjusting Screw, SST 1/2 thru 2-inch body 1N4991 99202
1/4-inch body 1L4495 35232 38 Handwheel
1/2-inch body 1L4497 35232 1/4-inch body 1L2175 44992
3/4 and 1-inch body 1L3244 35232 1/2 thru 1-inch body 1L3696 44992
1-1/2 and 2-inch body 21A980 8X012 1-1/2 and 2-inch body 1J4108 19042
34 Packing Follower 39* Female Adaptor, TFE
1/4-inch body 1/4-inch body 1F1244 01012
SST 1K8850 35072 1/2 thru 2-inch body 1H7844 01012
*Recommended spare part.
8
Types 95LD and 95HD
Key 12 Diaphragm
Body Size (Inch) Neoprene 302 SST (2 req’d) Fluoroelastomer
Type 95HD
1/4 1E393502112 1E392836012 1E393502402
1/2 1E396602112 1E395836012 1E396602402 (2 req’d)
3/4 & 1 1E399902112 1E399236012 1E399902402 (2 req’d)
1-1/2 & 2 1P788102192 1P787836012 11A1347X012
Type 95LD
1/4 1E394102112 1E393936012 1E394102402
1/2 1E397102112 1E396936012 1E397102402 (2 req’d)
3/4 & 1 1E390302112 1E390536012 1E390302332 (2 req’d)
1-1/2 & 2 --- --- ---
While this information is presented in good faith and believed to be accurate, or any other matter with respect to the products, nor as a recommendation to
Fisher Controls does not guarantee satisfactory results from reliance upon such use any product or process in conflict with any patent. Fisher Controls reserves
information. Nothing contained herein is to be construed as a warranty or guar- the right, without notice, to alter or improve the designs or specifications of the
antee, express or implied, regarding the performance, merchantability, fitness products described herein.
10
Printed in U.S.A.