Professional Documents
Culture Documents
Material This property data is a summary of similar materials in the MatWeb database for the
Notes: category "Low Density Polyethylene (LDPE), Molded". Each property range of values
reported is minimum and maximum values of appropriate MatWeb entries. The comments
report the average value, and number of data points used to calculate the average. The
values are not necessarily typical of any specific grade, especially less common values and
those that can be most affected by additives or processing methods.
Vendors: Click here to view all available suppliers for this material.
Please click here if you are a supplier and would like information on how to add your listing
to this material.
Physical Metric English Comments
Properties
Density 0.910 - 0.980 g/cc 0.0329 - 0.0354 lb/in³ Average value: 0.921 g/cc
Grade Count:192
Water 0.0100 % 0.0100 % Average value: 0.0100 %
Absorption Grade Count:14
Moisture 0.0100 % 0.0100 % Average value: 0.0100 %
Absorption at Grade Count:12
Equilibrium
Particle Size 5.00 - 50.0 µm 5.00 - 50.0 µm Average value: 27.5 µm
Grade Count:3
Water Vapor 15.5 - 18.6 g/m²/day 0.998 - 1.20 g/100 in²/day Average value: 17.4
Transmission g/m²/day Grade Count:5
Oxygen 197 - 200 cc-mm/m²-24hr-atm 500 - 508 cc-mil/100 in²-24hr-atm Average value: 199 cc-
Transmission mm/m²-24hr-atm Grade
Count:5
Viscosity 21000 - 305000 cP 21000 - 305000 cP Average value: 91600 cP
@Temperature 190 - 190 °C @Temperature 374 - 374 °F Grade Count:8
21000 - 305000 cP 21000 - 305000 cP Average value: 91600 cP
@Shear Rate 300 - 5000 1/s @Shear Rate 300 - 5000 1/s Grade Count:8
Environmental 1.00 - 1500 hour 1.00 - 1500 hour Average value: 338 hour
Stress Crack Grade Count:6
Resistance
1.00 - 1.00 hour 1.00 - 1.00 hour Average value: 1.00 hour
@Temperature 50.0 - 50.0 °C @Temperature 122 - 122 °F Grade Count:1
1.00 - 1.00 hour 1.00 - 1.00 hour Average value: 1.00 hour
@Thickness 2.00 - 2.00 mm @Thickness 0.0787 - 0.0787 in Grade Count:1
Maximum 0.100 0.100 Average value: 0.100
Moisture Grade Count:3
Content
Thickness 5.00 - 300 microns 0.197 - 11.8 mil Average value: 35.2
microns Grade Count:16
Linear Mold 0.0100 - 0.0500 cm/cm 0.0100 - 0.0500 in/in Average value: 0.0200
Shrinkage cm/cm Grade Count:8
Melt Flow 0.250 - 2300 g/10 min 0.250 - 2300 g/10 min Average value: 38.2 g/10
min Grade Count:169
Base Resin 0.500 - 25.0 g/10 min 0.500 - 25.0 g/10 min Average value: 6.32 g/10
Melt Index min Grade Count:9
Mechanical Metric English Comments
Properties
http://www.matweb.com/search/datasheet_print.aspx?matguid=557b96c10e0843dbb1... 2015-05-04
Overview of materials for Low Density Polyethylene (LDPE), Molded Page 2 of 4
http://www.matweb.com/search/datasheet_print.aspx?matguid=557b96c10e0843dbb1... 2015-05-04
Overview of materials for Low Density Polyethylene (LDPE), Molded Page 3 of 4
Elmendorf 1.84 - 45.8 g/micron 46.7 - 1160 g/mil Average value: 16.2
Tear g/micron Grade Count:7
Strength, TD
Dart Drop 2.36 - 30.0 g/micron 59.9 - 762 g/mil Average value: 6.06
g/micron Grade Count:12
Dart Drop 90.0 - 126 g 0.198 - 0.278 lb Average value: 106 g
Test Grade Count:6
Film Tensile 20.0 - 59.0 MPa 2900 - 8560 psi Average value: 30.1 MPa
Strength at Grade Count:13
Break, MD
Film Tensile 15.2 - 45.0 MPa 2200 - 6530 psi Average value: 22.8 MPa
Strength at Grade Count:13
Break, TD
Electrical Metric English Comments
Properties
Electrical 1.00e+15 - 1.00e+16 ohm-cm 1.00e+15 - 1.00e+16 ohm-cm Average value: 2.29e+15
Resistivity ohm-cm Grade Count:14
Surface 100 - 1.00e+14 ohm 100 - 1.00e+14 ohm Average value: 9.17e+13
Resistance ohm Grade Count:12
Dielectric 2.30 - 2.60 2.30 - 2.60 Average value: 2.33
Constant Grade Count:12
Dissipation 0.000200 0.000200 Average value: 0.000200
Factor Grade Count:12
Comparative 600 V 600 V Average value: 600 V
Tracking Grade Count:12
Index
Thermal Metric English Comments
Properties
CTE, linear 180 - 230 µm/m-°C 100 - 128 µin/in-°F Average value: 218 µm/m-
°C Grade Count:12
Melting Point 95.0 - 115 °C 203 - 238 °F Average value: 108 °C
Grade Count:67
Deflection 40.0 - 72.8 °C 104 - 163 °F Average value: 44.7 °C
Temperature Grade Count:18
at 0.46 MPa
(66 psi)
Deflection 38.0 - 101 °C 100 - 214 °F Average value: 71.2 °C
Temperature Grade Count:5
at 1.8 MPa
(264 psi)
Vicat 52.0 - 117 °C 126 - 243 °F Average value: 89.3 °C
Softening Grade Count:151
Point
Brittleness -85.0 - 0.000 °C -121 - 32.0 °F Average value: -52.5 °C
Temperature Grade Count:80
Flammability, HB HB Grade Count:12
UL94
Oxygen 17.0 % 17.0 % Average value: 17.0 %
Index Grade Count:11
Ring & Ball 109 - 130 °C 228 - 266 °F Average value: 118 °C
Softening Grade Count:4
Point
Optical Metric English Comments
Properties
Haze 3.30 - 20.0 % 3.30 - 20.0 % Average value: 8.46 %
Grade Count:13
http://www.matweb.com/search/datasheet_print.aspx?matguid=557b96c10e0843dbb1... 2015-05-04
Overview of materials for Low Density Polyethylene (LDPE), Molded Page 4 of 4
Some of the values displayed above may have been converted from their original units and/or rounded in order to display the information in a
consistent format. Users requiring more precise data for scientific or engineering calculations can click on the property value to see the
original value as well as raw conversions to equivalent units. We advise that you only use the original value or one of its raw conversions in
your calculations to minimize rounding error. We also ask that you refer to MatWeb's terms of use regarding this information. Click here to
view all the property values for this datasheet as they were originally entered into MatWeb.
http://www.matweb.com/search/datasheet_print.aspx?matguid=557b96c10e0843dbb1... 2015-05-04