PARTICULAR MATERIAL APPRAISAL
(PRESSURE EQUIPMENT DIRECTIVE-2014/68/EU)
Pressure Equipment Manufacturer: VRV ASIA PACIFIC PVT LTD 7
Rev.No. 02 Material Group & Sub Group: 8 & 8.1
ee Grade: WP 304 | Delivery condition: Solution Annealed
Dimension range:
Applicable Design Code: EN 13458-2 Annex C Diameter :9 1/4"0 9 6”
Wall thickness : 1.65 mm to 3.4mm
Applicati Det Comments
Vessel V | Type : Cryogenic Vessel
Piping -- | (Elbows, Tees,Reducers)
Equipment Pressure ~
Accessories -
Assembly
Gas |
Liquid -
ial Group 1 v
Group 2
1
Category u
uM
v v |
Operating Conditions: Details Comments
Maximum Allowable Working Pressure ( bar) | 17/18/23/24/36/37
Allowable Temperature Range °C -196 "C to 50°C
And where ever relevant
corrosion =
ageing =
formability :
weldability Suitable for welding
“machinability = ~
Specific Requirements
Property Requirement Specification Comments
Min. Yield strength 205 Mpa From ASME Sec,|I,Part D
Strength governs the allowable stress
Min. Tensile strength 515 Mpa and meets the requirement
Toughness at Lowest Impact test is exempted as
Toughness operating temperature | Not required per G-17 PED Guidelines.
-196 °C
Ductility 14% minimum 28% Meets the requirement
Formability NA NA =
Allowable Stress From ASME Sec,II,Part D
66 Mpa 138 Mp: governs the allowable stress
and meets the requirement
yl { i Page 1 of 2
We "PARTICULAR MATERIAL APPRAISAL
(PRESSURE EQUIPMENT DIRECTIVE-2014/68/EU)
Pressure Equipment Manufacturer: VRV ASIA PACIFIC PVT LTD
PMA Ref. No. : VRV/CE/03 [ Rev.No. 02 Material Group & Sub Group: 8 & 8.1
Material specification:
z i it d
5A AOaWP SOL EA 2017 | Grade: we 304 | Delivery condition: Solution Anneale
Applicable Design Code: EN 13458-2 Annex C
Dimension range
Diameter :B 1/4’0 8 6”
Wall thickness : 1.65 mm to 3.4 mm,
Conditions
In Addition to the requirements of the above speci
ation each batch of material used in this application shall
be covered by a certificate of specific material control as evidence of conformity with the following
requirements
Property Requirement Test method(Specification) | Comment
€-0.08%,Min-2.00%,P-
0.045%, 5-0.03%Si- SA751
1%,Ni-8-1196,Cr-18-20%
Chemical
Tensile Strength-
515Mpa;Yield Strength- | SA 370
minimum “type 3.1"
pee 205Mipa;tlongation-28%
Certification according to :
Material EN 10204:2004 fay eee ee eet
Certification Inspection Certificate | ~ age
Certificate “type 3.1
Traceability to heat/lot
Material Marking | identity of the material | --
manufacturer
Manufacturer name or trade
mark size, material
specification ,Drawing No
and Lot no.
The above material has been appraised for compliance with the essential safety requirements of the PED for
the above application and has been granted a Particular Material Appraisal subject to the conditions listed.
Revisions to the parent specification, by the issuing authority, are to be reviewed by the manufacturer, and
where applicable advised to the notified body, and may result in invalidation of this PMA
yu ee
Signed:
(Pressure Equipment Manufacturer)
Confirmed:
Notified Body (Cats Il & IV only)
Date: 26!" duly ro1e
Date:
Page 2 of 2