Professional Documents
Culture Documents
GENERAL DATA
CRANE CAPACITY 60,000 kg at 3.0 m
BOOM 5-section, 11.1 m – 42.0 m
DIMENSION
Overall length approx. 13,480 mm
Overall width approx. 2,590 mm
Overall height approx. 3,950 mm
MASS
Gross vehicle mass approx. 42,800 kg
-front axle approx. 15,800 kg
-rear axle approx. 27,000 kg
PERFORMANCE
Max. traveling speed computed 80 km/h (limiter)
*60 km/h (limiter for Singapore)
Gradeability (tan ) computed 50 %
CRANE SPECIFICATIONS
MODEL SINGLE TOP (AUXILIARY BOOM SHEAVE)
GS-600EX Single sheave.
Mounted to main boom head for single line work.
CAPACITY
60,000 kg at 3.0 m ELEVATION
By a double-acting hydraulic cylinder, fitted with holding valve.
BOOM Automatic speed reduction and slow stop function.
5-section full power partially synchronized telescoping boom Boom angle...................... –2˚ to 80˚
of hexagonal box construction with 5 sheaves at boom head. Boom raising speed.......... 20˚ to 60˚ in 36s
The synchronization system consists of 2 telescope cylinders,
extension cables and retraction cables. Selection of 2 boom HOIST-Main winch
telescoping modes. Variable speed type with grooved drum driven by hydraulic
Fully retracted length…………… 11.1 m axial piston motor through winch speed reducer. Power
Fully extended length…………... 42.0 m load lowering and hoisting.
Extension speed………………… 30.9 m in 130 s Equipped with automatic brake (Neutral brake) and counter-
balance valve. Controlled independently of auxiliary winch.
JIB Single line pull................. 54.9 kN {5,600 kgf}
2-staged slewing around boom extension. Triple offset (5˚/ 25˚/ Single line speed............. 146 m/min. (at the 4th layer)
45˚) type. Stows alongside base boom section. Assistant Wire rope......................... Spin-resistant type
cylinders for mounting and stowing. Single sheave at jib head. Diameter x length............ 19 mm x 227 m
Length …………………………… 8.8 m and 15.2 m
CRANE SPECIFICATIONS
SPEC. SHEET NO. GS-600E-1-90101/SP-01
-2-
CARRIER SPECIFICATIONS
SPEC. SHEET NO. GS-600E-1-90101/SP-01
MANUFACTURER SUSPENSION
SCANIA Front................................. Parabolic, leaf spring 4 x 28 with
anti-roll bar
MODEL Rear.................................. Trapezoid, leaf spring 8x30/90
P360 CB8x4 (Right-hand steering , 8 x 4) with anti-roll bar
TURN RADIUS
Min. turning radius (at center of extreme outer tire).......12.0m
EQUIPMENT
FOR CRANE Optional Equipment
Standard Equipment 60 t capacity hook block (6 sheaves)
Automatic moment Limiter (AML) 35 t capacity hook block (3 sheaves)
3-colors External lamp (AML) Over-unwinding prevention
Anti-two-block device
Winch automatic fail-safe brake
Winch drum rotation indicator (visual type)
Winch drum mirror FOR CARRIER
Cable follower Standard Equipment
5.6t capacity hook block (swivel hook) Reverse alarm with disabling
Hook safety latch Head lamp protection
Pilot check valves 12V socket in dashboard
Counterbalance valves Fold out step in bumper
Hydraulic pressure relief valves Boarding step lighting
Slewing brake Towing devise in front bumper
Slewing lock Protective rubber floor mats
Boom angle indicator Tool kit
Boom elevation foot pedal
Boom telescoping foot pedal
Outrigger extension width detector
Hydraulic oil cooler
3 working lights
Front windshield wiper and washer
Roof window wiper and washer
Power window (cab door)
3 way adjustable cloth seat with headrest and armrest
Cab floor mat
Sun visor (front and roof)
Air conditioner (hot water heater and cooler in upper cab)
Eco mode system
Tool box with lock key
Spare tire carrier with lock key
Telematics (machine data logging and monitoring system)
with – HELLO-NET via internet (availability depends on
countries)
-3-
WORKING RANGE
SPEC. SHEET NO. GS-600E-1-90101/SP-01
25˚
45
˚ Telescoping mode
5˚
65 BOOM
60
Approx.
2.5m
55
42
m
Bo 50
om
+1
5.2
42 m
80˚ m Jib JIB
Bo 45
70˚ om
+8
.8m
60˚ Jib
42 40
.0m 55˚
30˚
18 20
.8m
m
Bo 0.8 Approx.
15 o 2.3m
.0m 20˚
15
m
Bo
o
11.1
m
m
Bo
10
10˚
om
5
0˚
0
0 5 10 15 20 25 30 35 40
WORKING RADIUS (m)
26.6m
34.3m
42.0m
-4-
WORKING RANGE
SPEC. SHEET NO. GS-600E-1-90101/SP-01
25˚
45
˚ Telescoping mode
5˚
65 BOOM
60
Approx.
2.5m
55
42
m
Bo
om 50
+1
5.2
42 m
m Jib
Bo
80˚ om 45 JIB
+8
70˚ .8m
Jib
60˚
42 40
18 20
.8m
m
Bo 0.8 Approx.
15 om 20˚ 2.3m
.0m
Bo 15
11 om
.1m
Bo 10˚
om 10
5
0˚
0
0 5 10 15 20 25 30 35 40
WORKING RADIUS (m)
26.6m
34.3m
38.1m
42.0m
-5-
RATED LIFTING CAPACITIES (BOOM)
SPEC. SHEET NO. GS-600E-1-90101/SP-01
ISO 4305
UNIT: x1,000kg
Outriggers fully extended (7.0m)
A 11.1 15.0 18.8 26.6 34.3 38.1 42.0
B C C C C C C C C C C
2.5 72 60.0
3.0 69 60.0 75 40.0 78 28.0 78 20.0
3.5 66 53.1 73 40.0 77 28.0 76 20.0
4.0 63 47.4 71 40.0 75 28.0 75 20.0
4.5 60 42.6 69 40.0 74 28.0 73 20.0 79 20.0 79 14.0
5.0 57 38.6 66 38.3 72 28.0 72 19.3 78 20.0 78 14.0
5.5 53 35.1 64 34.9 70 27.5 70 18.5 77 20.0 77 14.0
6.0 50 32.2 62 31.9 69 25.6 68 17.8 76 20.0 75 13.2 80 14.0 79 8.5
6.5 46 29.6 60 28.6 67 23.9 67 17.2 75 19.3 74 12.4 79 14.0 79 8.5
7.0 42 26.9 57 25.5 65 22.4 65 16.5 74 18.1 73 11.7 78 13.7 78 8.5 79 8.5
7.5 38 23.4 55 22.9 64 21.0 63 16.0 72 17.0 72 11.1 77 13.0 77 8.5 79 8.5
8.0 33 20.7 53 20.1 62 19.0 62 15.5 71 16.0 71 10.5 76 12.5 76 8.5 78 8.5 80 8.5
9.0 21 16.5 47 16.0 58 15.7 58 14.5 69 14.4 69 9.5 75 11.4 74 7.7 77 8.4 78 8.5
10.0 42 13.0 54 12.8 54 13.7 67 13.0 66 8.7 73 10.5 73 7.0 75 7.6 77 8.1
11.0 35 10.7 50 10.4 50 12.7 64 11.3 64 7.9 71 9.7 71 6.4 74 7.0 76 7.5
12.0 27 8.9 46 8.6 46 10.8 62 9.7 61 7.3 70 8.9 69 5.9 72 6.5 74 6.9
14.0 36 6.0 36 8.0 56 7.1 56 6.2 66 7.4 66 4.9 69 5.5 72 6.0
16.0 23 4.2 23 6.2 51 5.3 51 5.4 62 5.7 62 4.2 65 4.7 69 5.2
18.0 45 3.9 45 4.8 58 4.3 58 3.6 62 4.1 66 4.5
20.0 38 2.9 38 4.2 54 3.3 54 3.2 59 3.6 63 3.7
22.0 29 2.1 30 3.4 49 2.5 49 2.8 55 3.1 59 2.9
24.0 17 1.5 18 2.8 44 1.9 44 2.5 51 2.6 56 2.2
26.0 39 1.4 39 2.2 47 2.0 52 1.7
28.0 33 0.9 33 1.9 42 1.6 48 1.3
30.0 25 0.6 26 1.5 37 1.2 44 0.9
32.0 15 1.2 31 0.9 40 0.6
34.0 24 0.6
36.0 13 0.4
D 0 37
Rated Lifting
Capacities 14.8 6.9 3.3 5.3 1.2 2.5 1.2
B 9.5 13.4 17.2 17.2 25.0 25.0 32.7 32.7 36.5 33.0
Telescoping Mode , ,
UNIT: x1,000kg
Outriggers extended to middle (6.0m)
A 11.1 15.0 18.8 26.6 34.3 38.1 42.0
B C C C C C C C C C C
2.5 72 60.0
3.0 69 56.9 75 40.0 78 28.0 78 20.0
3.5 66 50.1 73 40.0 77 28.0 76 20.0
4.0 63 44.5 71 40.0 75 28.0 75 20.0
4.5 60 39.9 69 39.6 74 28.0 73 20.0 79 20.0 79 14.0
5.0 57 36.0 66 35.8 72 28.0 72 19.3 78 20.0 78 14.0
5.5 53 32.7 64 32.4 70 27.5 70 18.5 77 20.0 77 14.0
6.0 50 29.4 62 28.4 69 25.6 68 17.8 76 20.0 75 13.2 80 14.0 79 8.5
6.5 46 24.5 60 23.7 67 23.2 67 17.2 75 19.3 74 12.4 79 14.0 79 8.5
7.0 42 20.8 57 20.1 65 19.7 65 16.5 74 18.1 73 11.7 78 13.7 78 8.5 79 8.5
7.5 38 18.0 55 17.4 63 16.9 63 16.0 72 17.0 72 11.1 77 13.0 77 8.5 79 8.5
8.0 33 15.7 53 15.2 62 14.8 62 15.5 71 16.0 71 10.5 76 12.5 76 8.5 78 8.5 79 8.5
9.0 21 12.3 47 11.8 58 11.5 58 13.8 69 12.7 69 9.5 75 11.4 74 7.7 77 8.4 78 8.5
10.0 42 9.4 54 9.1 54 11.4 66 10.3 66 8.7 73 10.5 73 7.0 75 7.6 77 8.1
11.0 35 7.6 50 7.3 50 9.5 64 8.4 64 7.9 71 9.0 71 6.4 73 7.0 76 7.5
12.0 27 6.2 46 5.9 46 8.0 61 7.0 61 7.3 69 7.6 69 5.9 72 6.5 74 6.9
14.0 36 3.9 36 5.9 56 5.0 56 6.2 65 5.5 65 4.9 69 5.5 71 5.8
16.0 23 2.5 23 4.4 50 3.6 51 4.9 61 4.1 62 4.2 65 4.7 68 4.4
18.0 44 2.5 45 3.8 57 3.0 58 3.6 62 3.6 65 3.3
20.0 37 1.7 38 3.0 53 2.2 54 3.2 58 2.8 62 2.5
22.0 29 1.1 29 2.3 49 1.6 49 2.5 54 2.2 58 1.8
24.0 17 0.6 17 1.8 44 1.0 44 2.0 50 1.6 55 1.3
26.0 38 0.6 39 1.6 46 1.2 51 0.9
28.0 33 1.2 42 0.8
30.0 25 0.9 36 0.5
32.0 14 0.6
D 0 35 0 32 50
Rated Lifting
Capacities 10.6 4.0 1.9 3.6 0.4 1.5 0.4 0.4 0.4 0.4
B 9.5 13.4 17.2 17.2 25.0 25.0 27.3 32.7 31.6 26.9
Telescoping Mode , ,
UNIT: x1,000kg
Outriggers extended to minimum (5.1m)
A 11.1 15.0 18.8 26.6 34.3 38.1 42.0
B C C C C C C C C C C
2.5 71 60.0
3.0 69 53.5 75 40.0 78 28.0 78 20.0
3.5 66 46.9 73 40.0 77 28.0 76 20.0
4.0 63 41.6 71 40.0 75 28.0 75 20.0
4.5 60 37.1 68 36.8 73 28.0 73 20.0 79 20.0 79 14.0
5.0 57 32.3 66 31.3 72 28.0 72 19.3 78 20.0 78 14.0
5.5 53 26.0 64 25.2 70 24.7 70 18.5 77 20.0 77 14.0
6.0 50 21.6 62 20.8 69 20.4 68 17.8 76 20.0 75 13.2 80 14.0 79 8.5
6.5 46 18.2 60 17.6 67 17.2 67 17.2 75 18.5 74 12.4 79 14.0 79 8.5
7.0 42 15.6 57 15.1 65 14.7 65 16.5 73 16.0 73 11.7 78 13.7 78 8.5 79 8.5
7.5 38 13.5 55 13.0 63 12.7 63 15.1 72 13.9 72 11.1 77 13.0 77 8.5 79 8.5
8.0 33 11.9 53 11.4 62 11.0 62 13.4 71 12.3 71 10.5 76 12.5 76 8.5 78 8.5 79 8.5
9.0 21 9.3 47 8.8 58 8.5 58 10.8 69 9.7 69 9.5 75 10.3 74 7.7 77 8.4 78 8.5
10.0 42 6.9 54 6.7 54 8.8 66 7.8 66 8.7 73 8.4 73 7.0 75 7.6 77 8.1
11.0 35 5.5 50 5.3 50 7.3 64 6.4 64 7.8 71 6.9 71 6.4 73 7.0 75 7.2
12.0 27 4.4 46 4.2 46 6.2 61 5.3 61 6.7 69 5.8 69 5.9 72 6.5 74 6.1
14.0 36 2.5 36 4.4 56 3.6 56 4.9 65 4.1 65 4.9 68 4.7 71 4.4
16.0 23 1.4 23 3.2 50 2.4 51 3.7 61 2.9 62 3.9 65 3.5 68 3.2
18.0 44 1.5 44 2.8 57 2.1 58 3.0 62 2.6 65 2.3
20.0 37 0.8 38 2.1 53 1.4 53 2.3 58 2.0 61 1.6
22.0 29 1.5 48 0.8 49 1.8 54 1.4 58 1.1
24.0 17 1.1 44 1.3 50 1.0
26.0 39 0.9
28.0 33 0.6
D 0 29 0 48 14 46 58
Rated Lifting
Capacities 8.2 3.0 0.8 2.6 0.4 0.9 0.4 0.4 0.4 0.4
B 9.5 13.4 17.2 17.2 22.2 25.0 22.5 32.0 25.9 22.3
Telescoping Mode , ,
-6-
RATED LIFTING CAPACITIES (JIB)
SPEC. SHEET NO. GS-600E-1-90101/SP-01
ISO 4305
ON OUTRIGGERS
Outriggers fully extended (7.0m)
(Unit: ×1000kg)
42.0m Boom + 8.8m Jib 42.0m BOOM + 15.2m JIB
C 5˚Tilt 25˚Tilt 45˚Tilt C 5˚Tilt 25˚Tilt 45˚Tilt
R W R W R W R W R W R W
80 10.1 4.5 13.1 2.7 15.1 1.9 80 12.7 2.7 17.4 1.3 20.9 0.9
79 11.1 4.5 14.1 2.7 16.1 1.9 79 13.9 2.7 18.5 1.3 22.0 0.9
78 12.2 4.5 15.1 2.6 17.0 1.9 78 15.1 2.6 19.6 1.3 23.0 0.9
77 13.2 4.4 16.0 2.6 17.9 1.9 77 16.2 2.5 20.7 1.2 24.0 0.8
76 14.1 4.2 17.0 2.5 18.8 1.8 76 17.3 2.4 21.8 1.2 25.0 0.8
75 15.0 4.0 17.9 2.5 19.7 1.8 75 18.4 2.3 22.9 1.2 26.0 0.8
73 16.8 3.6 19.8 2.4 21.5 1.8 73 20.6 2.1 25.0 1.1 28.0 0.8
70 19.5 3.2 22.5 2.3 24.1 1.7 70 23.7 1.8 28.0 1.0 30.8 0.8
68 21.2 2.9 24.3 2.2 25.8 1.7 68 25.8 1.7 30.0 1.0 32.7 0.8
65 23.7 2.5 26.8 2.0 28.2 1.7 65 28.7 1.5 32.8 0.9 35.3 0.7
63 25.3 2.3 28.4 1.9 29.8 1.6 63 30.6 1.4 34.7 0.9 37.0 0.7
60 27.7 1.8 30.7 1.6 32.0 1.5 60 33.4 1.2 37.3 0.9 39.4 0.7
58 29.1 1.5 32.0 1.3 33.4 1.2 58 35.1 1.0 39.0 0.9 41.0 0.7
55 31.1 1.1 33.9 0.9 35.1 0.9 55 37.4 0.7 41.3 0.5 43.1 0.5
53 32.4 0.8 35.1 0.7 36.1 0.7
50 34.3 0.5 36.8 0.5 37.7 0.5
ON OUTRIGGERS
Outriggers extended to middle (6.0m)
(Unit: ×1000kg)
42.0m Boom + 8.8m JIB 42.0m Boom + 15.2m JIB
C 5˚Tilt 25˚Tilt 45˚Tilt C 5˚Tilt 25˚Tilt 45˚Tilt
R W R W R W R W R W R W
80 9.9 4.5 12.9 2.7 14.9 1.9 80 12.5 2.7 17.0 1.3 20.6 0.9
79 10.9 4.5 13.9 2.7 15.8 1.9 79 13.6 2.7 18.1 1.3 21.6 0.9
78 12.0 4.5 14.8 2.6 16.8 1.9 78 14.8 2.6 19.2 1.3 22.6 0.9
77 12.9 4.4 15.8 2.6 17.7 1.9 77 15.9 2.5 20.3 1.2 23.6 0.8
76 13.9 4.2 16.7 2.5 18.6 1.8 76 17.0 2.4 21.3 1.2 24.6 0.8
75 14.8 4.0 17.7 2.5 19.5 1.8 75 18.1 2.3 22.4 1.2 25.6 0.8
73 16.6 3.6 19.5 2.4 21.2 1.8 73 20.2 2.1 24.4 1.1 27.5 0.8
70 19.2 3.2 22.2 2.3 23.8 1.7 70 23.3 1.8 27.4 1.0 30.3 0.8
68 20.9 2.8 24.0 2.2 25.4 1.7 68 25.3 1.7 29.4 1.0 32.1 0.8
65 23.2 2.1 26.3 1.8 27.9 1.7 65 28.2 1.5 32.2 0.9 34.7 0.7
63 24.7 1.7 27.7 1.5 29.2 1.4 63 29.9 1.2 34.0 0.9 36.4 0.7
60 26.9 1.2 29.7 1.0 31.0 1.0 60 32.3 0.8
58 28.3 0.9 31.0 0.8 32.2 0.8
-8-
RATED LIFTING CAPACITIES (JIB)
SPEC. SHEET NO. GS-600E-1-90101/SP-01
ISO 4305
ON OUTRIGGERS
Outriggers extended to minimum (5.1m)
(Unit: ×1000kg)
42.0m Boom + 8.8m JIB 42.0m Boom + 15.2m JIB
C 5˚Tilt 25˚Tilt 45˚Tilt C 5˚Tilt 25˚Tilt 45˚Tilt
R W R W R W R W R W R W
80 9.8 4.5 12.7 2.7 14.9 1.9 80 12.2 2.7 16.8 1.3 20.4 0.9
79 10.8 4.5 13.7 2.7 15.9 1.9 79 13.4 2.7 17.8 1.3 21.4 0.9
78 11.8 4.5 14.6 2.6 16.8 1.9 78 14.5 2.6 18.9 1.3 22.4 0.9
77 12.8 4.4 15.5 2.6 17.7 1.9 77 15.6 2.5 19.9 1.2 23.4 0.8
76 13.7 4.2 16.5 2.5 18.6 1.8 76 16.7 2.4 21.0 1.2 24.4 0.8
75 14.6 4.0 17.4 2.5 19.5 1.8 75 17.8 2.3 22.0 1.2 25.4 0.8
73 16.4 3.6 19.2 2.4 21.2 1.8 73 19.9 2.1 24.1 1.1 27.3 0.8
70 18.8 2.5 21.8 2.1 23.8 1.7 70 22.9 1.8 27.0 1.0 30.1 0.8
68 20.4 2.0 23.3 1.7 25.3 1.5 68 24.7 1.4 28.9 1.0 31.8 0.8
65 22.7 1.3 25.5 1.2 27.3 1.1
63 24.2 1.0 26.9 0.9
-9-
RATED LIFTING CAPACITIES ISO 4305
SPEC. SHEET NO. GS-600E-1-90101/SP-01
NOTES :
1. Rated lifting capacities shown in the table are based on condition that crane is set on firm level surface. Those above thick lines are
based on crane strength and those below, on its stability.
3. The mass of the hook (570kg for *60 t capacity, 450 kg for *35t capacity, 150kg for 5.6t capacity), slings and all similarly used load
handling devices must be considered as part of the load and must be deducted from the lifting capacities. (* Optional)
4. For rated lifting capacity of single top, reduce the rated lifting capacities of relevant boom according to a weight reduction for auxiliary
load handling equipment. Capacities of single top shall not exceed 5,600 kg including main boom hook mass and the net capacity
must be so reduced.
5. Standard number of parts of line for each boom length is as shown below. Load per line should not surpass 54.9 kN {5,600 kgf} for
main winch and auxiliary winch.
Boom length 11.1m 15.0m 18.8m 26.6m 34.3m to 42.0m Single top
Jib
Number of model I 8∼6
12 10∼8 6∼4 4 1
parts of line model II 6∼4
The lifting capacity data stowed in the AUTOMATIC MOMENT LIMITER (AML) is based on the standard number of parts of line listed
in the chart.
Maximum lifting capacity is restricted by the number of parts of line of AUTOMATIC MOMENT LIMITER (AML).
-10-
DIMENSION
SPEC. SHEET NO. GS-600E-1-90101/SP-01
50
,6
R3
I NG
W
ILS
TA
2,590
MIN. 5,155
MIN. 5,100
1,475
2,745
MID. 6,000
310
MAX. 7,000
0 φ
40 6,521.5 40
φ 0
6,738
6,995
22°
Ý
500
1,590 1,940 3,760 1,445 2,175
2,315 10,910 255
13,480
-11 -
Specifications are subject to change without notice.
(International Division)
4-12, Kamezawa 2-chome,
Sumida-ku, Tokyo 130-0014, Japan
Tel : +81-(0)3-3621-7750
Fax : +81-(0)3-3621-7785
URL http : // www.tadano.com/
E-mail info@tadano.com
Printed in Japan
GS-600EX-2014-06-01