Professional Documents
Culture Documents
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this
information by clicking on the below link for the most accurate information:
http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=02460&Standard=061&
NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects
NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact
Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click
here for the definitions of Water Contact Temperatures denoted in these Listings.
Facility : Alexander, AR
Water Water
Water Contact Contact Contact
Trade Designation Size Restriction Temp Material
Coatings - Fittings
Amercoat 133[1] >= 4" CLD 23 EPOXY
Amercoat 133/Amercoat 333[2] >= 4" CLD 23 EPOXY
info.nsf.org/Certified/PwsComponents/Listings.asp?Company=02460&Standard=061 1/9
4/5/2020 Listing Category Search Page | NSF International
Coatings - Pipe
Amercoat 133[1] >= 30" CLD 23 EPOXY
Amercoat 133/Amercoat 333[2] >= 12" CLD 23 EPOXY
Amerlock 2[3] >= 48" CLD 23 EPOXY
Novaguard 810[4] [5] CLD 23 EPOXY
Novaguard 810ER[4] [5] CLD 23 EPOXY
Novaguard 840[13] >= 36" CLD 23 EPOXY
Novaguard 840 Filler[14] [15] CLD 23 EPOXY
[15] Certified for a maximum of 25% of the surface area of a 500 gallon tank and greater and
12" pipe and greater.
info.nsf.org/Certified/PwsComponents/Listings.asp?Company=02460&Standard=061 3/9
4/5/2020 Listing Category Search Page | NSF International
Coatings - Pump
Amerlock 2[3] >= 4" CLD 23 EPOXY
[3] Colors: Ivory, medium gray, oxide red, RT 1805 blue, white, black
Number of Coats: 2-4
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 8 per coat; 18 total
Maximum Thinner: 12% Amercoat #65 by volume; 12% Amercoat #8 by volume (alternate)
Recoat Cure Time and Temperature: 24 hours at 72ºF
Final Cure Time and Temperature: 10 days at 72°F for all end uses except tank >= 250,000
gallons which has a final cure of 7 days at 72ºF
Special Comments: Use of Amercoat #8 thinner is limited to tanks of 250,000 gallons of
greater.Mix ratio of base:cure is 1:1 by volume or 1.1:1 by weight.
Coatings - Tank
Novaguard 840 Filler[14] [15] CLD 23 EPOXY
Amercoat 133[1] >= 50 gal. CLD 23 EPOXY
Amercoat 133/Amercoat 333[2] >= 500 gal. CLD 23 EPOXY
Amercoat 133 + 884 Additive[6] [7] CLD 23 EPOXY
Amerlock 2[3] >= 2000 gal. CLD 23 EPOXY
Amercoat 68HS[8] >= 5,000 gal CLD 23 EPOXY
Amercoat 68PW[8] >= 5,000 gal CLD 23 EPOXY
Novaguard 810[4] [5] CLD 23 EPOXY
Novaguard 810ER[4] [5] CLD 23 EPOXY
Novaguard 840[13] >= 1500 gal. CLD 23 EPOXY
info.nsf.org/Certified/PwsComponents/Listings.asp?Company=02460&Standard=061 4/9
4/5/2020 Listing Category Search Page | NSF International
minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape
the sides of the can while mixing.
[3] Colors: Ivory, medium gray, oxide red, RT 1805 blue, white, black
Number of Coats: 2-4
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 8 per coat; 18 total
Maximum Thinner: 12% Amercoat #65 by volume; 12% Amercoat #8 by volume (alternate)
Recoat Cure Time and Temperature: 24 hours at 72ºF
Final Cure Time and Temperature: 10 days at 72°F for all end uses except tank >= 250,000
gallons which has a final cure of 7 days at 72ºF
Special Comments: Use of Amercoat #8 thinner is limited to tanks of 250,000 gallons of
greater.Mix ratio of base:cure is 1:1 by volume or 1.1:1 by weight.
[4] Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 30
Recoat Cure Time and Temperature: 24 hours at 70°F
Final Cure Time and Temperature: See Listing Note.
[5] Certified for tanks >= 500 gallons, pipe >=22", and valves >=2" with a final cure of 72
hours @ 77º F and tanks >= 250,000 gallons and valves >= 3/4" with a final cure of 10
days at 40º F.
[6] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 10 dry film thickness in a skim coat
over pitted steel
Maximum Thinner: None
Final Cure Time and Temperature: 7 days at 70ºF (>=250,000 gallon tank), 10 days at 70ºF
(< 250,000 gallons)
Special Comments: Amercoat 133: Mix ratio of resin to cure is 4:1 by volume. Mix for 5
minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape
the sides of the can while mixing. After mixing Amercoat 133, add Amercoat 884 at up to
0.5 lb. per gallon.
[7] Certified for a maximum of 10% of the surface area of a 500 gallon tank.
[8] Colors: Reddish Gray, Green
Number of coats: 1
Sequence of coats: Primer
Maximum field use dry film thickness: 4 mils
Maximum thinner: 6% Amercoat 65
Final Cure Time and temperature: 8 hours at 75°F
Special comments: Mix ratio is 3.02:1.00:13.01 (Part A:PartB:Powder) by weight. Any
certified PPG top coat may be used provided both primer and top
coat meet their individual Certified end uses.
[13] Colors: Cream, Green
Number of Coats: 1-2
Maximum field use dry film thickness (in mils): 30
Recoat cure time and temperature: 24 hours at 70°F
Final cure time and temperature: 72 hours at 70°F
Special Comments: Mix ratio of base to hardener is 4:1 by volume
info.nsf.org/Certified/PwsComponents/Listings.asp?Company=02460&Standard=061 5/9
4/5/2020 Listing Category Search Page | NSF International
[15] Certified for a maximum of 25% of the surface area of a 500 gallon tank and greater and
12" pipe and greater.
Coatings - Valve
Amercoat 133[1] >= 4" CLD 23 EPOXY
Amercoat 133/Amercoat 333[2] >= 4" CLD 23 EPOXY
Amerlock 2[3] >= 6" CLD 23 EPOXY
Amercoat 370[9] >= 4" CLD 23 EPOXY
Amerlock 400[10] >= 6" CLD 23 EPOXY
Novaguard 810[4] [5] CLD 23 EPOXY
Novaguard 810ER[4] [5] CLD 23 EPOXY
Novaguard 840[13] >= 4" CLD 23 EPOXY
minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape
the sides of the can while mixing.
[3] Colors: Ivory, medium gray, oxide red, RT 1805 blue, white, black
Number of Coats: 2-4
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 8 per coat; 18 total
Maximum Thinner: 12% Amercoat #65 by volume; 12% Amercoat #8 by volume (alternate)
Recoat Cure Time and Temperature: 24 hours at 72ºF
Final Cure Time and Temperature: 10 days at 72°F for all end uses except tank >= 250,000
gallons which has a final cure of 7 days at 72ºF
Special Comments: Use of Amercoat #8 thinner is limited to tanks of 250,000 gallons of
greater.Mix ratio of base:cure is 1:1 by volume or 1.1:1 by weight.
[4] Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 30
Recoat Cure Time and Temperature: 24 hours at 70°F
Final Cure Time and Temperature: See Listing Note.
[5] Certified for tanks >= 500 gallons, pipe >=22", and valves >=2" with a final cure of 72
hours @ 77º F and tanks >= 250,000 gallons and valves >= 3/4" with a final cure of 10
days at 40º F.
[9] Colors: Black, light buff, oxide red, milliken blue, white
Number of Coats: 2-4
Maximum Field Use Dry Film Thickness (in mils): 24
Maximum Thinner: 12.5% Amercoat #65 Thinner
Recoat Cure Time and Temperature: 0.5 hours at 23°C
Final Cure Time and Temperature: 7 days at 23°C
Special Comments: Mix ratio of base:cure is 4:1 by volume.
[10] Colors: Ivory, medium gray, oxide red, RT-1805, white
Number of Coats: 2-4
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 18 total
Maximum Thinner: 12.5% Amercoat #65 by volume
Recoat Cure Time and Temperature: 24 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Mix ratio of base:cure is 1:1 by volume.
[13] Colors: Cream, Green
Number of Coats: 1-2
Maximum field use dry film thickness (in mils): 30
Recoat cure time and temperature: 24 hours at 70°F
Final cure time and temperature: 72 hours at 70°F
Special Comments: Mix ratio of base to hardener is 4:1 by volume
Primers[11] [12]
Sigmaweld 199 US >= 900 gal. CLD 23 ZINC
info.nsf.org/Certified/PwsComponents/Listings.asp?Company=02460&Standard=061 7/9
4/5/2020 Listing Category Search Page | NSF International
[11] This primer may be used with any Certified PPG topcoat provided both primer and topcoat
meet their individual Certified end uses.
[12] Colors: Green
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 1
Maximum Thinner: None
Recoat Cure Time and Temperature: Not Applicable
Final Cure Time and Temperature: Primer (cure before application of topcoat) - 7 days at
ambient temperature (20°C)
Special Comments: Mix ratio of binder:paste is 2:1 by volume. Apply to steel substrate.
Facility : Waller, TX
Water Water
Water Contact Contact Contact
Trade Designation Size Restriction Temp Material
info.nsf.org/Certified/PwsComponents/Listings.asp?Company=02460&Standard=061 9/9