Professional Documents
Culture Documents
Keep It Light !!!: Spitfire Mkix
Keep It Light !!!: Spitfire Mkix
F1d
KEEP IT LIGHT !!! All balsa light grade unless stated
F1a F1b F1c R10
R9
R3
R2
R1
F12 F11
T4
T3
T2
T1
C of G
Mould exhaust stubs from plastic PLAN VIEW OMMITING PLANKING & FIN
tubing heated over mandrel
Sanded chamfer TAILPLANE HALF-SHEETED Tailplane sheeting 1mm balsa
True-to-scale
wing root fairing shape
F2c
Motor clamp Sub assemblies:-
(alternative) Exhaust manifold No.1 F3b, F4b, F5b, F6b, F10 & F11(2)
3mm liteply No.2 F1a,b,c, F2a, F3a, F4a, F12(2), F13 & F14
No.3 F6a, F6c, F15 & F16 F6c Tailplane platform
3mm balsa
No.4 F1d, F2c, F3c, F4c & F12c
F6a
F2c F3c
Hole positions to suit
height of servo
F8a F9a
F2a F3a F4a F5a F7a During construction check relative widths
of fuselage & fin which join on this line
F5f
W2
Balsa filler piece Wing washout jig Dihedral jig
3mm balsa
W3
Laminated aileron
Balsa/0.4mm birch ply/balsa
Tack-glue to wing when sanding to shape
IMPORTANT! Accuracy essential.
Remove this area & check for
Chamfer bottom of rib Cut slots for 0.4mm ply trailing e
1.5mm sheeting allowance between using junior hacksaw fitted with
Alignment dowels rib profile and centre section then replace. metal-cutting blade
Remove finally after sheeting
underside of centre panel.
Servo access
Underside only
(Size to suit servo)
W6
W7
Wing centre section assembly jig Cannon from aluminium tube & balsa
2-off 10mm balsa
W12
Use in conjunction with 2 lengths of
3mm dia. piano wire approx. 250 long Alternative shrouded hinge design.
Requires 5mm thick fin post.
Also applicable to tailplane
grain
Wing root fairing base
Add aileron spar Sand slots for hinges before glueing Add one half of ribs. 0.4mm birch ply
Sheet underside centre bay. both halves of spar together Sheet one side whilst maintaining flatness. (True length shown)
Glue L.H. panel to centre section. Add other halves of leading & trailing edges.
Add laminated trailing edge. Add other halves of ribs. Cut centre away after
Add false leading edge. Sheet remaining side. planking wing root fairing
Sheet remainder of underside of wing. R10 Sand to finish
Add wheel-well & reinforcement to W3.
Add cannon support & servo access.
Provide for u/c. air & electrics. Round-off to 'soften' edge
R9
Sheet upper surface of wing with
washout jig under rear spar position.
Add leading edge laminations. T9
Add wingtip core & sheeting. R8
Sand & finish. T8
Repeat for R.H. panel. Rudder trim-tab core
0.4mm ply
R7
T7
Elevator trim-tab core Carburettor air intake
0.4mm ply Hollowed block balsa
R6 Pin jig to wing using balsa
T6 packing such that cowl sides
Radiator cowl assembly jig
will be o
at 90 to cowl bottom.
3mm balsa
Pin cowl sides to jig.
Cyano cowl sides to wing.
Rudder perimeter frame
R5 Remove jig.
0.4mm ply
Sheet underside of cowl
T5
R4
T4
R3 T3
Horn seat
R2
3mm balsa between T1 & T1 T2
Elevator perimeter frame
0.4mm ply
CONSTRUCTION GUIDELINES
FOR ELEVATORS & RUDDER
Wing-tip core
0.4mm ply
SPITFIRE
MkIX
Glue leading & trailing edges to one side
of plywood perimeter frame.
Rudder horn Add notched half of ribs.
R1 T1 Part sheet one side whilst maintaining flatness.
1mm aluminium
Add other halves of leading & trailing edges.
Retract unit mount Seat horn on 3mm balsa above R2 Add other halves of ribs.
2 layers of 3mm liteply then edge with balsa to support covering Part sheet remaining side.
between 0.8mm birch ply
(Total thickness 7.6mm) Rudder post
5mm balsa
Fin & rudder ribs
1.5mm balsa
Tailplane & elevator ribs
1.5mm balsa
Sand to finish
First in a series of 1/9th scale WW
(Two sets required)
Designed by Dave Philpotts
SHEET 2 2000
For 500/600 geared electric motors
F6f F11
F6f F2c
3mm liteply
grain F3c
F1c F6c
F11
F6b
F12a F9
F12a F9b
F12
F6a
F1b F12
F8
F13
F3
F2 F16
F7
F5
F4
F1a
F5f F5f
W1
W4 W5
3mm liteply
2 off each W11 2mm liteply
W2
2 off each
W6 W7
grain
W12 grain
W3
W8 W9 W10
R10 T7 T9
R3 T8
T7
R8
T5
T8
Paste templates onto wood using glue stick
R2
T2
R7
T5
R1 T2
R6
R5
R9
T3
T3
T4
T9
SPITFIRE
MkIX
Fin & rudder ribs
1.5mm balsa T1 T6
R4 T6
Tailplane &
T1 T4 elevator ribs
1.5mm balsa