Professional Documents
Culture Documents
Uses Properties
! Safe to use - water based, containing no harmful solvents. Concure DPM should be well stirred before use. Application
No risk of fire. should be made to the surface of concrete by brush or
squeegee at a rate of 6m2 per litre per coat. Two coats should
! Chemical resistance - resists attack from chlorides and
be applied, allowing the first coat to dry completely before
sulphates in ground water.
applying the second. The second coat should be applied at
right angles to the first. All applications should be continued
Standards compliance
up verticals to existing damp proof course. Ensure that the
Concure DPM complies with the coating ability and water membrane is not punctured or damaged during any
resistance requirements of AASHTO M 140. subsequent operations.
Overcoating
Description
Where slab surface is to receive a render or plaster finish a
Concure DPM is a rubber reinforced bitumen emulsion
keyed surface should be formed by gritting the second coat
based curing compound. When first applied to a fresh
of Concure DPM with clean dry sand. Allow a minimum drying
cementitious surface the product forms a dark brown
period of 48 hours before plastering, rendering or laying of a
continuous non-penetrating coating.
floor screed. Damaged areas of Concure DPM can be readily
This coating dries to form a black flexible continuous film overcoated to restore the continuity of the membrane.
which provides a barrier to moisture loss ensuring more
Cleaning
efficient cement hydration, improved durability and reduced
shrinkage. It then remains in place providing a permanent All equipment should be cleaned immediately after use.
damp proof membrane which resists the passage of Concure DPM can be removed with clean water while wet.
aggressive salts that are present in ground water, providing However, once the material has dried, it can only be removed
lasting protection to the concrete. with Fosroc Solvent 102*.
Concure DPM is designed for application in two coats Fosroc provides a technical advisory service for on-site
to achieve a total dry film thickness of approximately assistance and advice on admixture selection, evaluation
100 microns. trials and dispensing equipment. Technical data and
guidance can be provided for admixtures and other products
for use with fresh and hardened concrete.
Concure DPM
Fosroc Concure DPM
Estimating Precautions
Note: Coverage rates outside this recommended range may Some people are sensitive to resins and solvents. Barrier
be used if necessary and suitable to meet specific creams such as Kerodex Antisolvent or Rozalex Antipaint
requirements. Contact the Fosroc Technical Service provide additional skin protection. Should accidental skin
department for advice in such cases. contact occur remove immediately with a resin removing
cream such as Kerocleanse Standard Grade Skin Cleanser
Storage or Rozaclens Industrial Skin Cleanser, followed by washing
withsoap and water - do not use solvent. In case of contact
Shelf life with eyes rinse immediately with plenty of clean water and
Concure DPM and Fosroc Solvent 102 have a shelf life of 6 seek medical advice. If swallowed seek medical attention
months minimum if kept in a dry store between 5ºC and 30ºC immediately - do not induce vomiting.
in the original, unopened containers. For further information consult the Material Safety Data Sheet
Storage conditions available for this product.
Flash point
Fosroc Solvent 102 : 33ºC
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for
the Supply of Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to
obtain the latest version.
Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
United Arab Emirates Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
www.fosroc.com
Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com
Qatar, Tadmur telephone: 4432365 fax: 4419517 email: qatar@fosroc.com
UAE/0320/08/D