Professional Documents
Culture Documents
Carboxyimidazole (CDI) discs are used for covalent immobilisation of ligands (e.g. proteins,
peptides and other amine or thiol containing molecules). The covalent nature of the bond
between the ligand and matrix reduces leaching and improves stability and reusability.
Immobilised supports enable a variety of customised analytical affinity chromatography
options with interactions specific to the target molecule. The following information is
provided to ensure proper product care and optimal product performance.
Unpacking
Carefully inspect the product for any damage that may have occurred during shipping. Immediately report any such damage to
your vendor and the courier. The product is shipped in the designated storage solution at room temperature and should be
stored upon arrival as stated in the table Characteristics of the monolith.
Due to low hydrolytic stability of immobilised ligand, the ligand density could decrease by 25% of the initial density after 3
months. Thus CIM® monoliths activated with carbonyl imidazole ligand (CDI monoliths) are only produced on request and after
issued order confirmation by BIA Separations.
It is therefore advisable for the customer to couple the molecule of interest on the CDI monoliths as soon as possible after
receiving the product. Once the ligand of interest is immobilised on the monolithic support, the CDI stability is not a concerning
issue anymore.
WARNING: Do not store the product below 0 °C (32 °F).
General recommendations
Consider the following general guidelines and always operate the column with chemistry-specific limitations in mind.
• Treat loading material appropriately (e.g. pre-treat, filter, concentrate / dilute, etc.). For more details, please refer to the
Guideline ‘Pre-treatment of complex biological samples before column purification and regeneration procedures for columns
with increased back pressure’ (biaseparations.com/en/library/guidelines).
• Always use freshly prepared buffers. Filter buffers and samples through 0.2 μm filter.
• Always ensure buffers are compatible before mixing them or applying consecutively on the column. In particular, wash the
column before and after 1 M NaOH. Examples of in-compatible buffers are: magnesium ion-containing buffers and sodium
hydroxide (forms precipitate), acetonitrile and sodium hydroxide (forms ammonia and acetate), ethanol and sodium
The monolithic column needs to be assembled for use. Follow any instructions on the packaging before proceeding. To assemble
the column:
1. Unscrew the screw cap from the housing and remove the retaining fitting
2. With tweezers, remove the disk from its container and place it gently into the housing cylinder.
Note: Up to four 0.1 mL or two 0.2 mL discs can be inserted into the housing simultaneously.
3. Reinsert the retaining fitting and screw on the screw cap, finger-tight.
Note: Make sure the o-ring is in place on the retaining fitting before inserting it in the housing cylinder. A missing o-ring could
result in leakage from the column.
4. Seal the assembled column with blind fitting.
Ordering information
See overleaf for a selection of products. Additional products are available or can be prepared on-demand. Contact our sales team
for further information.
Scale-up products
Catalog number Product name
311.8000-2 CIMmultus™ CDI 1 mL Monolithic Column (Carbonyldiimidazole) (2 µm channels)
411.8000-2 CIMmultus™ CDI 8 mL Monolithic Column (Carbonyldiimidazole) (2 µm channels)
611.8000-2 CIMmultus™ CDI 80 mL Monolithic Column (Carbonyldiimidazole) (2 µm channels)
811.8000-2 CIMmultus™ CDI 800 mL Monolithic Column (Carbonyldiimidazole) (2 µm channels)
Information and specifications contained here are, to the best of our knowledge, accurate and represented in good faith. They are intended to help you start working with
this new separation technology and are subject to change without notice. BIA Separations shall not be liable for errors contained herein or for incidental or consequential
damages which may occur during use. For more information on our products, visit our home page at: http://www.biaseparations.com or contact your local distributor. We
reserve the right to alter the specification without notice or liability.