Professional Documents
Culture Documents
REVISION LOG
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 2 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
Table of Contents
NOTATION .........................................................................................................................................5
2.0 GENERAL...............................................................................................................................9
6.0 CONCLUSIONS....................................................................................................................41
7.0 REFERENCES......................................................................................................................42
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 3 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 4 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
NOTATION
°C Degrees Celsius
CA Corrosion Allowance
CD Chart Datum
°F Degrees Fahrenheit
GL Gas Lift
Km Kilometer
MG Marine Growth
OD Outside Diameter
PL Pipeline
PP Polypropylene
RP Recommended Practice
SF Safety Factor
SG Specific Gravity
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 5 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
STV Su Tu Vang
WD Water Depth
WI Water Injection
WT Wall Thickness
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 6 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
The design of each riser at WHP-B platform derives a proper configuration with respect to
the jacket geometry, pipeline expansions and the applied operational and environmental
load conditions. The design of tie-in spools at STV subsea midline tie-in locations derives a
proper configuration with respect to the STV subsea midline tie-in geometry, pipeline
expansion and the applied operational and environmental load conditions.
The objectives of this ‘Riser and Subsea Tie-in Spool Analysis’ report are:
• To list, or reference, the pipeline and riser design data, environmental data and other
information pertaining to the in-place analysis of the risers and associated expansion
spools, and the tie-in spools at STV subsea midline tie-in to accommodate operational
expansion of the pipelines.
• To assess the in-place strength of the risers and the subsea tie-in spools, and to ensure
no overstress is induced on the riser/tie-in spool throughout their service life due to
combined static, environmental, pressure and thermal loads.
• To determine the maximum restraint forces at the riser hanger clamp and guide clamp
supports, so that the design of the riser supports is adequate to provide sufficient
support to the riser system.
• To ensure that no vortex induced vibrations (VIV) will occur on the risers.
The stress analyses of the risers and tie-in spools have been performed using COADE, Inc.
CAESAR II Version 5.00 software. The riser and expansion spool model includes a segment
of the topside piping and extends up to at least 25m from the first spool bend on the seabed.
The subsea tie-in spool model includes a segment of the pipeline and extends up to at least
25m from the first spool bend on the seabed. The soil spring stiffnesses have been modeled
as vertical supports with stiffness derived from the submerged weight and the expected soil
settlement. For pipelines that have more than one external coating, the combined thickness
of the coatings with an equivalent density has been used.
The submerged weight of the spools/pipeline and the weight of their coatings have been
generated in the CAESAR model. For the stress check for the operating condition only, the
3mm corrosion allowance has been considered to calculate the stresses as per the
applicable codes ASME B31.4 and ASME B31.8.
The integrity of risers and associated expansion spools, and subsea tie-in spools have been
verified for the critical combination of functional and environmental loads, which includes the
maximum pipeline end expansions previously established for the pipelines [Ref. 3]. The
resulting stresses in each riser and associated expansion spool, and subsea tie-in spool are
compared with the allowable stresses given by the design codes of ASME B31.4 and/or
ASME B31.8 [Refs. 5, 6]. The design cases considered in the analyses of the risers and
associated expansion spools, and subsea tie-in spools are:
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 7 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
The riser spans between the riser supports have also been checked in accordance to the
DnV’81 [Ref. 2] code requirements to ensure that no vortex induced vibrations (VIV) can
occur on any segments of the risers. From this assessment, the locations the riser clamp
support are ascertained to ensure that the span lengths between the guides are less than
the calculated allowable span lengths. The VIV dynamic spans have been performed using
in-house MS Excel spreadsheet.
From the results of the analyses performed herewith, it can be concluded that the risers and
associated expansion spools (at WHP-B), and the subsea tie-in spools (at STV subsea
midline tie-in locations) for the various lines are adequate to sustain the maximum combined
environmental and functional loads for both the operating and hydrotest conditions. There is
no overstress throughout the riser and associated expansion spool system, and tie-in spool
system at STV subsea midline tie-in locations. The risers and expansion spools, and subsea
tie-in spools meet the code requirements and hence will be safe throughout their service
lives.
The tie-in flange ratings proposed for the risers and spools are stated in Table 3.2.1. The
proposed tie-in flange ratings shall be verified (based on the maximum forces and moments
acting on the flanges) by the selected flange vendor during detailed engineering phase.
The results of the analyses performed have been summarized in Section 5.0 of this report.
The VIV riser span calculations can be found in Appendix A of this report. Appendix B
presents the CAESAR II input and output files for all the risers and associated expansion
spools, and the subsea tie-in spools analyzed.
From the expansion analysis performed [Ref. 3], it was found that the 10.75-inch and 16-
inch pipeline expansions are minimal and these expansions can be accommodated with
smaller expansion spools at the inlet and outlet ends of the pipelines. However, the tie-in
spools for the 10.75-inch and 16-inch pipelines are recommended to facilitate the tie-in to
the risers (at the WHP-B platform) and the STV subsea midline tie-in arrangement.
The STV 10.75-inch GL and 16-inch WI tie-in spool configurations at STV/STDNE interface
location are being currently modified as part of STV project scope of work in order to
facilitate the pigging operation from CPP platform to WHP-B platform. Accordingly, the
STDNE 10.75-inch GL and 16-inch WI tie-in spool configurations at STV/STDNE interface
location were modified and shown in the drawings (Ref. 11). As per the new tie-in
configuration, the STDNE 16-inch WI straight tie-in spool is directly connected to the STDNE
16-inch pipeline without any expansion loop and therefore no expansion tie-in spool analysis
is required to be performed.
The 24-inch riser and associated expansion loop at WHP-B are designed for the pipeline
end expansions which were computed by considering one mid-line expansion loop to be
located (as remedial measure to prevent pipeline lateral buckling) along the proposed
STDNE 24-inch pipeline route.
The design of the topside piping is beyond the scope of this report. The stress checks of the
risers terminate at the riser battery limits, which is at EL (+) 6.50m.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 8 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
2.0 GENERAL
This Riser and Subsea Tie-in Spool Analysis Report has been prepared for Cuulong Joint
Operating Company (CLJOC) as part of the preliminary engineering for the development of
the Su Tu Den North East (STDNE) field located in Block 15-1 offshore Vietnam,
approximately 7 km North East of the Su Tu Den development phase-1. This document
contains the design data, criteria, Code of practice, assumptions and methodologies to be
used for the preliminary engineering of in-field pipeline and riser system of the Su Tu Den
North East project.
Under current scope of work, CLJOC intends to install a wellhead platform (WHP-B), three
(3) in-field pipelines and a composite power and fiber optic submarine cable for the Su Tu
Den North East field development. WHP-B will receive production from the north east region
of the Su Tu Den reservoir and deliver it via pipeline to the Central Processing Platform
(CPP) installed at Su Tu Vang. Lift gas and injection water shall be delivered to WHP-B via
the infield pipeline networks supplied from the CPP and the Cuu Long MV9 FPSO. The
WHP-B will include the wellhead and utility equipments. It will not be designed with any
processing capability. The unprocessed production will flow from WHP-B to STV CPP
through a 24-inch multiphase pipeline.
This report establishes the riser and expansion spool design at the WHP-B risers including
their allowable spans and stresses, and the tie-in spools (at STV subsea midline tie-in
locations). The stresses were computed for the operational and environmental parameters,
inline with the technical requirements outlined in the ‘Pipeline Design Basis’ [Ref. 1], for the
following risers and associated expansion spools, and subsea tie-in spools. The riser scope
begins at the hanger clamp and ends at the outlet flange of the associated expansion spool.
At the WHP-B:
• A 406.4mm OD (16-inch) subsea tie-in spool at the STV 16-inch seawater injection
pipeline (CPP to midpoint tap) subsea midline tie-in location.
• A 273.1mm OD (10.75-inch) subsea tie-in spool at the STV 10.75-inch gas lift pipeline
(CPP to midpoint tap) subsea midline tie-in location.
• Subsea lateral arrangements on the 10.75-inch Gas Lift and 16-inch Seawater Injection
tie-in spools at WHP-B platform to facilitate the future tie-in to the Su Tu Nau pipelines.
The subsea lateral arrangements are as follows:
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 9 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
- 10.75-inch Gas Lift Tie-in: Tee connection with double-block bleed valves
+ blind flange
- 16-inch Seawater Injection Tie-in: Tee connection with blind flange
The layout of the 16-inch and 10.75-inch subsea tie-in spools at the STV subsea midline tie-
in locations are shown in the drawings [Ref. 11].
The design of the 24-inch expansion loop at the WHP-A PLEM for the STDNE 24-inch
production pipeline was covered in the STV project (Doc No. 2004-6031-2J-0010, Ref. 9).
Therefore, the analysis of the 24-inch expansion spool at WHP-A PLEM is not addressed in
this report. The proposed layout of the 24” expansion loop at the WHP-A PLEM is shown in
the drawing [Ref. 12].
A field layout showing the proposed pipelines and cable is presented in Figure-2.1.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 10 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
SU TU VANG (STV)
CPP
PLEM AT FSO
TEMPORARY FSO
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 11 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
The pipeline dimensional data for the various lines are specified in the following table
[Ref. 1].
NOTE:
[1] Pipe thinning is considered in the riser analysis at all pipe bends, such that the pipe wall thickness reduced to
account for 10% thinning allowance conservatively.
The pipeline operating and hydrotest pressures are used for the operating and
hydrotest cases respectively. These pressures are summarized below. The hydrotest
pressures satisfy the Vietnamese code requirement [Ref. 8] and are equivalent to
1.50 times the pipeline design pressures.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 12 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
The proposed pipeline coating data for the various risers and pipelines are specified
in Table 3.3.1 [Ref. 1].
NOTES:
[1] Average 4LPP density as per Coating Manufacturer recommended.
[2] Applied only to expansion spool and pipeline on the seabed sections only.
[3] For the insulated lines, all risers are to be insulated (4LPP) without concrete coating.
The product densities for the various pipelines have been outlined in Table 3.4.1
[Ref. 1].
This section presents the design environmental and meteorological data for the
pipeline system [Ref. 1].
The parameters in Table 3.5.1.1 define the constants associated with the seawater
environment [Ref. 1].
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 13 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
Parameters Value
The water depths at the platform, PLEM and subsea tie-in locations [Ref. 1] are
given in Table 3.5.2.1 below.
NOTE:
[1] The CD is (-) 2.19m below MSL.
The wave and current parameters considered for the pipeline design are given in the
following table [Ref. 1].
Sig. Wave Height m (ft) 3.5 (11.48) 5.5 (18.04) 8.0 (26.25)
• Mid depth m/s (ft/s) 0.8 (2.63) 1.0 (3.28) 1.2 (3.94)
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 14 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
NOTE:
[1] The current above are the total current assumed to be taken @ 1 m above the seabed.
The following soil parameters were considered in the expansion loops design based
on the soil data summarized in the CLJOC Pipeline Design Basis [Ref. 1].
• Soil Type : Sand
• Angle of internal friction : 25 degree
• Sand density : 1740 - 1860 kg/m3
• Longitudinal coefficient of friction : 0.5
• Lateral coefficient of friction : 0.5 – 0.7
The soil springs are inputted as vertical supports with stiffness derived from the
submerged weight and the expected soil settlement during hydrotest condition.
The minimum seawater temperature is used throughout the design. The seawater
temperatures are summarized below [Ref. 1]:
The marine growth profile [Ref. 1] shown in Table 3.5.6.1 is applied to riser pipe
radius for riser analysis under operating condition. Marine growth has not been
considered for the hydrotest condition. No marine growth is considered for the
pipeline and pipe spool on the seabed.
0 51 1400
Mudline 25 1400
The hydrodynamic coefficients to be considered for pipelines and riser design are
given in Table 3.5.7.1 below [Ref. 1].
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 15 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
The WHP-B platform displacements are considered for the riser flexibility analysis. The
1-year (hydrotest condition) and 100-year (operation condition) platform displacement
values are presented in Tables 3.6.1 to 3.6.3. These platform deflections are extracted
from the WHP-B jacket in-place strength analysis performed by the structural group
using MicroSAS software. These platform deflections shall be verified based on the
final WHP-B jacket in-place strength analysis to be performed during detailed
engineering phase. The platform deflections presented in Tables 3.6.1 to 3.6.3 are
based on the MicroSAS coordinate axis system shown below.
Y
(Vertical)
X (Platform East)
Z (Platform South)
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 16 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
Displacement (mm)
Elevation, MSL (m)
1 Year Storm 100 Year Storm
Loading Direction
X Y Z X Y Z
NOTES:
[1] The directions of x, y and z are defined in Figure 3.6.1.
[2] The platform deflections at the riser clamp locations are linearly interpolated/extrapolated based on
the deflection values presented above.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 17 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
Displacement (mm)
Elevation, MSL (m)
1 Year Storm 100 Year Storm
Loading Direction
X Y Z X Y Z
NOTES:
[1] The directions of x, y and z are defined in Figure 3.6.1.
[2] The platform deflections at the riser clamp locations are linearly interpolated/extrapolated based on
the deflection values presented above.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 18 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
Displacement (mm)
Elevation, MSL (m)
1 Year Storm 100 Year Storm
Loading Direction
X Y Z X Y Z
NOTES:
[1] The directions of x, y and z are defined in Figure 3.6.1.
[2] The platform deflections at the riser clamp locations are linearly interpolated/extrapolated based on
the deflection values presented above.
The platform deflections presented in Tables 3.6.1 to 3.6.3 were inputted in the CAESAR
analysis as per the CAESAR coordinate axis system shown below:
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 19 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
Y
(Vertical)
Z (Platform West)
X (Platform South)
Wind loading is negligible compared to the wave loads up to the wave crest level
acting on the riser above water level. However, wind loading is considered in the
riser analysis.
NOTES:
[1] Referenced to 10 m above MSL.
[2] Due to CAESAR II program ‘Windload Generator’ limitation, the minimum basic wind speed
input shall be not less than 32 m/s. Hence, a wind speed of 32 m/s is conservatively
considered for both operating condition and hydrotest load cases.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 20 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
4.1 General
This section establishes the maximum distances between supports based on the
limiting dynamic spanning criteria (susceptibility to vortex shedding vibration).
Each span is verified by taking into consideration of VIV due to fluid flow. Vortex
shedding generating a riser dynamic response is dependent on:
To avoid the possibility of such dynamic excitation, the maximum permissible free-span
length (i.e. the maximum distance between supports) is determined, based on a
comparison of the frequency of vortex shedding and the natural frequency of the riser
span.
St U c
f n=
Dt
For determination of the velocity ranges where vortex shedding induced oscillations
may occur, a parameter called the reduced velocity (Vr), is used. Vr is defined as:
Uc
Vr=
Dt f n
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 21 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
1/2
C 1 EI
f n=
2π me L4
me = mp + mc + ma
The added mass, ma, corresponds to the mass of water which vibrates with the riser,
and shall be taken as being equal to the mass of water displaced by the volume of the
pipe plus coatings.
Another parameter controlling the response of the riser is the stability parameter, Ks,
defined as:
2 me δ
Ks= 2
Ρ w Dt
Two types of oscillations may occur; oscillations in line with the velocity vector (in-line
motion), and oscillations perpendicular to the velocity vector (cross-flow motion).
The flow velocity for the onset of in-line motion is dependent on Ks.
Cross-flow oscillations may occur for Ks < 16 and values of Vr as determined from the
DnV Rules. The velocity for onset of cross-flow motion is dependent on the Reynolds
Number of the flow across the riser span.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 22 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
The amplitude of the cross-flow motion is dependent on Ks, the stability parameter.
The critical span length, Lcr, for a known set of environmental conditions is calculated
as:
1/2
B Dt V r
Lcr =
Uc
where:
1/2
15.4 E I
B=
2π me
The following load case is considered during the vortex shedding analyses:
Environmental loads are generated by wave and current. Wave and steady current
induced velocities acting on the riser span has been calculated using JP Kenny’s
Pipecalc ‘environmental data module’ and these have been used as input in VIV span
analysis in-house developed Excel spread sheet.
The results of the dynamic span analysis based on vortex shedding analysis for the
proposed riser clamp locations are summarized in Table 4.3.1. In the calculations, the
maximum environmental loads are taken at the mid-span. The detailed calculations are
presented in Appendix A.
The vortex shedding analyses are performed for the operation condition only since
operation is identified as a critical condition for the VIV span check compared to the
installation and hydrotest conditions.
Based on the above analysis, the proposed riser clamp locations are satisfactory for
design of the riser against vortex shedding vibration. Since the riser spans are designed
for no vibrations and the recommended span lengths are well within the true span
lengths, no fatigue analysis is further required.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 23 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 24 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
5.0 Analysis
5.1 General
The design of the risers and associated expansion spools at WHP-B platform, and
subsea tie-in spools at the STV subsea mideline tie-in locations are based on the
requirements of either ASME B31.8 or ASME B31.4 [Refs. 5, 6], as applicable. The
following analyses are performed to demonstrate that the proposed riser and
expansion spools are acceptable:
5.2 Software
The commercially available software CAESAR II version 5.0 [Ref. 7], a pipe stress
analysis and design program has been used to analyze the risers and spool pieces.
CAESAR II uses simple beam elements and defined loading conditions to analyze
complex piping systems subjected to static and dynamic loading. The piping system
may be subjected to operating, buoyancy and wave loading and also has the
capability to model pipe soil interaction. It performs pipe stress analysis based on
parameters such as temperature changes, pressure, system weight, anchor, support
restraint, movements, wave, soil stiffness, flanges and the effect of support
friction/guide support gaps. With this input, CAESAR II produces results in the form
of displacements, loads, and stresses throughout the system. Additionally, CAESAR
II compares these results to limits specified by recognized codes and standards,
including ASME B31.4/B31.8 used herein.
The water particle instantaneous velocities and acceleration are determined using
CAESAR II, Version 5.0, wave generator module, Stoke’s 5th order Wave Theory.
The geometry of the risers and the associated expansion spools, and subsea tie-in
spools modelled in CAESAR II have been based on the latest drawings [Refs. 10,
11].
The risers and the expansion spools are modelled as a system of finite elements
(nodes) supported by a system of anchors, guides, restraints and seabed supports.
The operating pressures, temperatures, end pipeline expansion are specified as
input-data, and the program calculates the resultant stresses and displacement of
the riser. The hydrodynamic loads acting on the risers are internally calculated using
the Morrison equation by CAESAR II, wave generator module based on modified
Stoke’s 5th order wave theory and are directly applied to the riser individual pipe
elements to experience loading due to hydrodynamic effects. The nodal geometry for
the risers and spools are presented with the CAESAR II input/output files in
Appendix B. Nodal points are located at specific riser clamp locations, platform
displacements, changes in material properties, splash zone and marine growth. The
model ends are represented by anchor points. The valves and flanges are modelled
as rigid element and the weight of valves and flanges distributed over the entire
length of the rigid element. The program calculates the resulting load distribution
over the length of the riser. The expansion of the pipeline on the seabed due to
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 25 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
The riser and tie-in spool stresses are calculated under the operational conditions i.e.
functional plus environmental for all possible critical wave directions. Jacket deflections
are applied at riser clamp locations dependent on wave directions. The physical
properties and materials modelled in the analysis are as defined in the riser physical
properties given in Section 3.0 Tables. An equivalent coating/insulation thickness and
density are used for the pipe with 4LPP and concrete coating thicknesses.
The analysis performed under hydrotest condition is based on for the uncorroded
riser with no marine growth, using 1 year storm wave and current condition.
The nodal geometries of the CAESAR II model for each of the riser and associated
expansion spools, and subsea tie-in spool assembly are presented as follow:
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 26 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
CAESAR II MODEL 24” PRODUCTION RISER & ASSOCIATED EXPANSION SPOOL @ WHP-B
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 27 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
CAESAR II MODEL 10.75” GAS LIFT RISER & ASSOCIATED EXPANSION SPOOL @ WHP-B
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 28 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
CAESAR II MODEL 16” SEAWATER INJECTION RISER & ASSOCIATED EXPANSION SPOOL
@ WHP-B
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 29 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
CAESAR II MODEL 10.75” GAS LIFT TIE-IN SPOOL AT STV SUBSEA MIDLINE TIE-IN
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 30 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
At the top end of the riser, sufficient length of topside piping has been modeled to
represent the piping at the cellar deck.
Soil supporting the pipeline and spool piece segments in contact with the seabed are
modelled in CAESAR II using a combination of rigid vertical supports +FY (upward) and
vertical springs. The seabed friction factor of is taken as 0.7. The soil stiffness is
modelled using elastic vertical springs on the seabed.
Ws
K=
d
A 3mm corrosion allowance has been used in the model at the pipeline section for
the operating case only. For hydrotest condition, no corrosion allowance is
necessary and the nominal wall thickness of the riser and expansion spool has been
used. The CAESAR II software calculates the various stresses using the corroded
and uncorroded wall thickness as applicable for the respective codes ASME B31.8
(chapter VIII) and ASME B31.4 (Chapter IX).
The pipeline end expansions under hydrotesting and operating conditions for the
various pipelines due to the combined effect of pressure, temperature and soil
friction forces are summarised in Table 5.6.1 below. These expansions have been
determined in pipeline expansion report [Ref. 3]. In the riser and tie-in spool analysis
undertaken in the present study, the pipeline expansion is modeled as a fixed
displacement of the riser and spool assembly. The displacement is applied in the
direction of the pipeline, heading towards the platform and subsea midline tie-in as
applicable. The stress analyses shall consider the displacements at the
riser/expansion spool bend locations to be at least equivalent to the expansion
values below.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 31 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
10.75-inch Subsea
WHP-B 0.131 0.103 0.246 0.041
Gas Lift Tie-in
NOTE:
[1] The 24-inch riser and associated expansion loop at WHP-B are designed for the pipeline end expansions
which were computed by considering one mid-line expansion loop to be located (as remedial measure to
prevent pipeline lateral buckling) along the proposed STDNE 24-inch pipeline route.
Both the operational and hydrotest cases are analyzed. The operational load case is
the most onerous for riser and tie-in spool design. The hydrotest case is performed
to determine the maximum loads for the hanger and clamp guide supports. Each
riser and expansion spool system is designed for both functional and environmental
loading conditions. These loads used in the analyses are given below:
• The pressure and temperature loads along the length of the pipeline and spool
are input based on the operating temperature and pressure as determined from
the steady state hydraulics analysis.
• The effect of the pipeline end expansion is included in the model by imposition of
displacements at a point on the pipeline section approximately 25m to 50m from
the pipeline tie-in flange.
• The platform deflections are applied in four principal wave directions as defined
in Section 5.7.3 of this document.
• Wind, wave and current generate environmental loads. The riser and tie-in spool
are designed to accommodate the governing combinations of functional loads with
the 100-year return environmental condition, and the hydrostatic test loads with the
1-year return environmental condition.
• The uniform weight due to corrosion and concrete coatings for each spool and
pipeline are input as an equivalent density in the model with a combined
thickness since CAESAR II only allowed for one type of external coating.
Operational and environmental load cases are combined to generate the "worst case"
scenarios as defined by the relevant design codes. The load combinations considered
for the riser and tie-in spool analysis are presented in Table 5.7.1.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 32 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
The maximum 100-year return period wave and current conditions have been
combined to act in the same direction as the platform displacements. The
hydrodynamics coefficients considered for the riser model are as follows:
The water particle instantaneous velocities and acceleration are determined at the
node points using CAESAR II, Version 5.0, “wave generator module”, Stokes 5th
Order Wave Theory and 7th Power Law current profile. The solution subsequently
obtained, provides the horizontal and vertical particle velocities (UX and UY), the
horizontal and vertical particle acceleration (AX and AY), and the surface elevation
above the mean water level. Once these parameters are available, the force on the
element can be computed using Morrison's equation:
F = 1/2 * ñ * Cd * D * U *I U I + π/4 * ñ * CM * D2 * A
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 33 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
The particle velocities and accelerations are vector quantities which include the effects
of any applied waves or currents.
Once the force on a particular element is available, it is placed in the system load vector
just as any other load is. A standard solution is performed on the system of equations
which describe the piping system. The piping system can be described by the standard
finite element equation:
The element loads generated by the hydrodynamic effects are placed in their proper
locations in {f}, similar to weight, pressure, and temperature. Once [K] and {f} are
finalised, a standard finite element solution is performed on this system of equations.
The resulting displacement vector {x} is then used to compute element forces, and
these forces are then used to compute the element stresses.
The wind loads on the segments of the riser above the water level are in the same
direction as the maximum platform deflection. The shape factor is taken as 0.50 for
cylindrical sections.
The riser displacements due to deflection of the jacket at various elevations due to
wave in four principal directions (data furnished by jacket structural group) for both 1
year storm and 100 year storm have been used in CAESAR calculation.
For operating conditions, 100 year storm data and for hydrotest condition 1 year
storm data have been used. For deflections at intermediate levels linear interpolation
has been made.
The load cases and combinations used for both operating and hydrotest conditions
have been selected to include both the environmental and functional loads. Tables
5.7.3.1 and 5.7.3.2 below list the basic load cases and combinations considered
under operating and hydrotest conditions for WHP-B risers and expansion spools.
P1 Pipeline pressure
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 34 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
W+T1+P1+D1+D5+WIN1+WAV1 Operating
W+T1+P1+D2+D5+WIN2+WAV2 Operating
W+T1+P1+D3+D5+WIN3+WAV3 Operating
W+T1+P1+D4+D5+WIN4+WAV4 Operating
W+T1+HP+D1+D5+WIN1+WAV1 Hydrotest
W+T1+HP+D2+D5+WIN2+WAV2 Hydrotest
W+T1+HP+D3+D5+WIN3+WAV3 Hydrotest
W+T1+HP+D4+D5+WIN4+WAV4 Hydrotest
The riser stress analyses have been performed for the operational and
environmental loads in accordance with the allowable stress criteria detailed below.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 35 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
NOTES:
[1] In the setting of design factors for B31.4, due consideration has been given to, and allowance
has been made for, the underthickness tolerance and maximum allowable depth of
imperfections provided for in the specification approved by the Code. Therefore, nominal pipe
wall thickness shall be used in the calculation of the principal stresses i.e. hoop, longitudinal
and combined stresses.
[2] In the wall thickness used in the calculation of combined stress for risers as per B31.8 shall be
based upon specified minimum wall thickness, including manufacturing, corrosion, and erosion
allowances.
[3] Stress is limited to 1.5 times of Operating Design Pressure or a Pressure that will result in a
Hoop Stress (based on specified Minimum Wall Thickness) equal to 90% of SMYS, whichever
is lesser in accordance with Section 12.1 of TCVN 6475.
Code stress equations for the actual and allowable stresses used in CAESAR II in
accordance to ASME B31.8 Chapter VIII and ASME B31.4 Chapter IX are as follows:
Hoop Stress
The hoop stress in accordance with ASME B31.4 shall not exceed the values given
below.
Sh ≤ F1(Sy)
The hoop stress in accordance with ASME B31.8 shall not exceed the values given
below.
Sh ≤ F1(Sy)T
Sh = (Pi - Pe)D/2t
where:
Sh = hoop stress, MPa
Pi = internal pressure, bar
Pe = external pressure, bar
D = nominal outside diameter of pipe, mm
t = nominal wall thickness, mm
T = Temperature Derating Factor from B31.8, Table 841.116A
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 36 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
Longitudinal Stress
|SL| ≤ F2S
Where:
SL = maximum longitudinal stress, MPa (positive tensile or negative
compressive)
F2 = longitudinal stress design factor from Table 5.8.1 for ASME B31.4 or
ASME B31.8, as applicable.
S = specified minimum yield strength (SMYS), MPa
|| = absolute value
Combined Stress
The combined stress can be determined using either the Tresca combined stress or
Von Mises combined stress.
The combined stress shall not exceed the value given by the Maximum Shear Stress
Equation (Tresca Combined Stress):
1/ 2
S − S h 2 2
2 L +S t ≤ F3 S
2
where:
SL = maximum longitudinal stress, MPa (positive tensile or negative
compressive)
Sh = hoop stress, MPa
S = specified minimum yield strength (SMYS), MPa
St torsional stress, MPa
F3 = combined stress design factor from Table 5.8.1 for ASME B31.4 or
ASME B31.8, as applicable
The combined stress shall not exceed the value given by the Maximum Distortional
Energy Theory (Von Mises Combined Stress):
1
[S h
2 2
− S L S h + S L + 3S t
2
]2
≤ F3 S
where:
SL = maximum longitudinal stress, MPa (positive tensile or negative
compressive)
Sh = hoop stress, MPa
S = specified minimum yield strength (SMYS), MPa
St = torsional stress, MPa
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 37 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
F3 = combined stress design factor from Table 5.8.1 for ASME B31.4 or
ASME B31.8, as applicable
Von Mises Combined Stress Criterion is used to determine the combined stress in
the riser and tie-in spools.
Only the governing stress ratios are reported in CAESAR II’s stress output.
The highest code stresses, which comply with the code requirements, are
summarized below and analyses results are presented in Appendix-B.
5.9.2 Results for 10.75-inch Gas Lift Riser & Spool at WHP-B
5.9.3 Results for 16-inch Seawater Injection Riser & Spool at WHP-B
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 38 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
5.9.4 Results for 10.75-inch Gas Lift Pipeline Subsea Tie-in Spool
The maximum reaction forces at the hanger and guide supports for all the risers
analyzed are summarized in the tables below.
The forces are given in the CAESAR II global axis system with the Y axis is being the
vertical and X axis is North-South direction and Z axis is the East-West direction of
the WHP-B Platform.
The maximum of the forces due to four principal directions of wind and wave are
shown in the following tables (Tables 5.10.1 to 5.10.3) for both operating and
hydrotest conditions.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 39 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
The riser clamps should be designed with suitable safety margin to accommodate
the operation plus environmental forces produced by the pipeline system and
hydrodynamic loads. All riser clamps are designed as part of jacket design scope.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 40 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
6.0 CONCLUSIONS
From the analyses and calculations performed, the following conclusions are drawn and
recommendations are forwarded:
• For all the risers and tie-in spools, there is no overstress locations when checked
against the code allowable stresses of ASME B31.4/B31.8. Hence, all the risers and
tie-in spools analyzed satisfy the code requirements and shall be safe throughout their
service lives.
• To satisfy the Vietnamese code requirement [Ref. 16], the hydrotest pressure used for
the riser and tie-in spools analyses shall be 1.50 times the design pressure (for
hydrotest condition). The riser and spool stresses are acceptable for the hydrotest
conditions.
• The riser clamp loads summarized in Tables 5.10.1 to 5.10.3 shall be used for the
design of hanger and guide supports for the risers.
• The spacing and numbers of riser clamps provided are sufficient in hindering in-
line/cross-flow vortex induced vibrations from occurring on the risers. Hence, no VIV
suppression devices are required for any of the risers. Since the riser spans are
designed for no vibrations in accordance with Dnv’81 and also the recommended span
lengths are within the true span lengths and thus justify no fatigue analysis further
required.
• The tie-in flange ratings proposed for the risers and spools are stated in Table 3.2.1.
The proposed tie-in flange ratings shall be verified (based on the maximum forces and
moments acting on the flanges) by the flange vendor during detailed engineering
phase.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 41 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
7.0 REFERENCES
6. ASME B31.4, Pipeline Transportation Systems for Liquid Hydrocarbons and Other
Liquids, 2002.
8. ‘Rules for the Classification and Technical Supervision of Subsea Pipeline Systems’,
Vietnamese code TCVN 6475.
10. Riser and expansion spools related drawings nos. 2005-6031-24-0001 and 2005-
6031-24-0002.
11. Subsea Tie-in Spools related drawings nos. 2005-6031-24-0005 and 2005-6031-24-
0007.
12. 24” Pipeline Expansion Loop Tie-in Details at WHP-A PLEM, Drawing no. 2005-
6031-24-0003.
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 42 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 43 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 44 of 49
J. Ray McDermott Asia Pacific Pte. Ltd.
Project no: R2455A
Client: Cuu Long Joint Operating Company CTR no: PPF-PLE-215
Project Title: Su Tu Field Development - Su Tu Den North East Document no: 2005-6031-2J-0010
Subject: Riser Allowable Span in accordance with DnV 81 Revision: C
By: SV
Checked: PS
4/20/2007 Page 1 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Project no: R2455A
Client: Cuu Long Joint Operating Company CTR no: PPF-PLE-215
Project Title: Su Tu Field Development - Su Tu Den North East Document no: 2005-6031-2J-0010
Subject: Riser Allowable Span in accordance with DnV 81 Revision: C
By: SV
Checked: PS
4/20/2007 Page 2 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
INPUT DATA
Clamp = CL 1
Pipeline Outer Diameter D = 609.6 mm
Nominal Pipeline Wall Thickness tn = 19.1 mm
Internal Corrosion Allowance CA = 3 mm
External Corrosion Coating or Insulation Thickness tcc = 33.5 mm
3
External Corrosion Coating or Insulation Density ρcc = 725 kg/m
Concrete Coating Thickness tconc = 0 mm
3
Concrete Coating Density ρconc = 0 kg/m
Water Absorption Percentage WA% = 0%
Marine Growth Thickness tmar = 153 mm
3
Marine Growth Density ρmar = 1400 kg/m
3
Content Density ρco = 40.8 kg/m
3
Seawater Density ρw = 1025 kg/m
Pipeline Steel Density ρst = 7850 kg/m3
Young's Modulus of Elasticity of Steel E = 207000 MPa
Gravity constant g = 9.805 m2/s
Maximum Wave Height Hw-max = 14.8 m
Wave Period Tp = 12.8 s
2
Wave Acceleration aw = 0 m/s
Wave Induced Velocity Uw = 4.41 m/s
Surface Current Velocity Ur = 1.4 m/s
Steady Current Velocity at Riser Span Uc = 1.4 m/s
2
Seawater Kinematic Viscosity ν = 1.03E-06 m /s
Elevation of Top Clamp ELtop = 5m
Elevation of Bottom Clamp ELbot = -13 m
Velocity Amplification Factor V.A.F. = 1
Jacket Batter (1 in X) X = 10
End Fixity = Pinned - Fixed
OUTPUT DATA
δ = 2 * π * 0.02
= 2 * 3.14 * 0.02
= 0.126
4/20/2007 Page 3 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Moment of Inertia, I
I = (π/64) * (D4 - (D - 2tc)4)
= 3.1416/64 * (609.6^4 - (609.6 - 2 * 16.1)^4)
4
= 1.323E+09 mm
Total Diameter, Dt
Dt = D + 2tcc + 2tconc + 2tmar
= 609.6 + 2 * 33.5 + 2 * 0 + 2 * 153
= 982.60 mm
4/20/2007 Page 4 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Reduced Velocity for Onset of In-Line Oscillation due to Current, (DnV, Figure A.3), VrIL-c
VrIL-c = 1.545 m/s
Ks_1 = 0.400
Ks_2 = 0.450
VrIL-c_1 = 1.490 m/s
VrIL-c_2 = 1.600 m/s
Allowable Span Length for Dynamic In-Line Oscillation due to Current, LIL-c
LIL-c = ((α/2π)VrIL-cDt/Uca(EI/Meff)0.5))0.5
= (15.4/(2 * 3.14) * (1.54 * (982.6/1000)/1.4) * ((207000 * 10^6 * 1322718431/10^12)/1673.2)^0.5)^0.5
= 32.79 m
Reduced Velocity for Onset of Cross-Flow Oscillation due to Current, (DnV, Figure A.5), VrCF-c
VrCF-c = 4.090 m/s
4/20/2007 Page 5 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Reca_1 = 1.00E+06
Reca_2 = 2.00E+06
VrCF-c_1 = 4.160 m/s
VrCF-c_2 = 3.950 m/s
Allowable Span Length for Dynamic Cross Flow Oscillation due to Current, LCF-c
LCF-c = ((α/2π)VrCF-cDt/Uca(EI/Meff)0.5))0.5
= (15.4/(2 * 3.14) * (4.09 * (982.6/1000)/1.4) * ((207000 * 10^6 * 1322718431/10^12)/1673.2)^0.5)^0.5
= 53.35 m
Reduced Velocity for Onset of Cross-Flow Oscillation due to Current + Wave, (DnV, Figure A.5), VrCF-cw
VrCF-cw = 3.855 m/s
Recwa_1 = 5.00E+06
Recwa_2 = 6.00E+06
VrCF-cw_1 = 3.860 m/s
VrCF-cw_2 = 3.850 m/s
Allowable Span Length for Dynamic Cross Flow Oscillation due to Current + Wave, LCF-cw
LCF-cw = ((α/2π)VrCF-cwDt/Ucwa(EI/Meff)0.5))0.5
= (15.4/(2 * 3.14) * (3.85 * (982.6/1000)/5.81) * ((207000 * 10^6 * 1322718431/10^12)/1673.2)^0.5)^0.5
= 25.42 m
Pipe Frequency, f
f = (α/(2πLgov 2))(EI/Meff)0.5
= (15.4/(2 * 3.1416 * 25.42^2)) * (207000 * 10^6 * 1322718431/10^12/1673.2)^0.5
= 1.53 Hz
Status = SAFE
4/20/2007 Page 6 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Project no: R2455A
Client: Cuu Long Joint Operating Company CTR no: PPF-PLE-215
Project Title: Su Tu Field Development - Su Tu Den North East Document no: 2005-6031-2J-0010
Subject: Riser Allowable Span in accordance with DnV 81 Revision: C
By: SV
Checked: PS
4/20/2007 Page 1 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Project no: R2455A
Client: Cuu Long Joint Operating Company CTR no: PPF-PLE-215
Project Title: Su Tu Field Development - Su Tu Den North East Document no: 2005-6031-2J-0010
Subject: Riser Allowable Span in accordance with DnV 81 Revision: C
By: SV
Checked: PS
4/20/2007 Page 2 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
INPUT DATA
Clamp = CL 1
Pipeline Outer Diameter D = 273.1 mm
Nominal Pipeline Wall Thickness tn = 12.7 mm
Internal Corrosion Allowance CA = 3 mm
External Corrosion Coating or Insulation Thickness tcc = 0.75 mm
3
External Corrosion Coating or Insulation Density ρcc = 1440 kg/m
Concrete Coating Thickness tconc = 0 mm
3
Concrete Coating Density ρconc = 0 kg/m
Water Absorption Percentage WA% = 0%
Marine Growth Thickness tmar = 153 mm
3
Marine Growth Density ρmar = 1400 kg/m
3
Content Density ρco = 185 kg/m
3
Seawater Density ρw = 1025 kg/m
Pipeline Steel Density ρst = 7850 kg/m3
Young's Modulus of Elasticity of Steel E = 207000 MPa
Gravity constant g = 9.805 m2/s
Maximum Wave Height Hw-max = 14.8 m
Wave Period Tp = 12.8 s
2
Wave Acceleration aw = 0 m/s
Wave Induced Velocity Uw = 4.4145 m/s
Surface Current Velocity Ur = 1.4 m/s
Steady Current Velocity at Riser Span Uc = 1.4 m/s
2
Seawater Kinematic Viscosity ν = 1.03E-06 m /s
Elevation of Top Clamp ELtop = 5m
Elevation of Bottom Clamp ELbot = -2.895 m
Velocity Amplification Factor V.A.F. = 1
Jacket Batter (1 in X) X = 10
End Fixity = Pinned - Fixed
OUTPUT DATA
δ = 2 * π * 0.02
= 2 * 3.14 * 0.02
= 0.126
4/20/2007 Page 3 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Moment of Inertia, I
I = (π/64) * (D4 - (D - 2tc)4)
= 3.1416/64 * (273.1^4 - (273.1 - 2 * 9.7)^4)
4
= 69705574 mm
Total Diameter, Dt
Dt = D + 2tcc + 2tconc + 2tmar
= 273.1 + 2 * 0.75 + 2 * 0 + 2 * 153
= 580.60 mm
4/20/2007 Page 4 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Reduced Velocity for Onset of In-Line Oscillation due to Current, (DnV, Figure A.3), VrIL-c
VrIL-c = 1.639 m/s
Ks_1 = 0.450
Ks_2 = 0.500
VrIL-c_1 = 1.600 m/s
VrIL-c_2 = 1.685 m/s
Allowable Span Length for Dynamic In-Line Oscillation due to Current, LIL-c
LIL-c = ((α/2π)VrIL-cDt/Uca(EI/Meff)0.5))0.5
= (15.4/(2 * 3.14) * (1.64 * (580.6/1000)/1.4) * ((207000 * 10^6 * 69705573.87/10^12)/650.52)^0.5)^0.5
= 15.75 m
Reduced Velocity for Onset of Cross-Flow Oscillation due to Current, (DnV, Figure A.5), VrCF-c
VrCF-c = 4.245 m/s
4/20/2007 Page 5 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Reca_1 = 7.00E+05
Reca_2 = 8.00E+05
VrCF-c_1 = 4.290 m/s
VrCF-c_2 = 4.240 m/s
Allowable Span Length for Dynamic Cross Flow Oscillation due to Current, LCF-c
LCF-c = ((α/2π)VrCF-cDt/Uca(EI/Meff)0.5))0.5
= (15.4/(2 * 3.14) * (4.25 * (580.6/1000)/1.4) * ((207000 * 10^6 * 69705573.87/10^12)/650.52)^0.5)^0.5
= 25.35 m
Reduced Velocity for Onset of Cross-Flow Oscillation due to Current + Wave, (DnV, Figure A.5), VrCF-cw
VrCF-cw = 3.877 m/s
Recwa_1 = 3.00E+06
Recwa_2 = 4.00E+06
VrCF-cw_1 = 3.880 m/s
VrCF-cw_2 = 3.870 m/s
Allowable Span Length for Dynamic Cross Flow Oscillation due to Current + Wave, LCF-cw
LCF-cw = ((α/2π)VrCF-cwDt/Ucwa(EI/Meff)0.5))0.5
= (15.4/(2 * 3.14) * (3.88 * (580.6/1000)/5.8145) * ((207000 * 10^6 * 69705573.87/10^12)/650.52)^0.5)^0.5
= 11.89 m
Pipe Frequency, f
f = (α/(2πLgov 2))(EI/Meff)0.5
= (15.4/(2 * 3.1416 * 11.89^2)) * (207000 * 10^6 * 69705573.87/10^12/650.52)^0.5
= 2.58 Hz
Status = SAFE
4/20/2007 Page 6 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Project no: R2455A
Client: Cuu Long Joint Operating Company CTR no: PPF-PLE-215
Project Title: Su Tu Field Development - Su Tu Den North East Document no: 2005-6031-2J-0010
Subject: Riser Allowable Span in accordance with DnV 81 Revision: C
By: SV
Checked: PS
4/20/2007 Page 1 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Project no: R2455A
Client: Cuu Long Joint Operating Company CTR no: PPF-PLE-215
Project Title: Su Tu Field Development - Su Tu Den North East Document no: 2005-6031-2J-0010
Subject: Riser Allowable Span in accordance with DnV 81 Revision: C
By: SV
Checked: PS
4/20/2007 Page 2 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
INPUT DATA
Clamp = CL 1
Pipeline Outer Diameter D = 406.4 mm
Nominal Pipeline Wall Thickness tn = 23.8 mm
Internal Corrosion Allowance CA = 3 mm
External Corrosion Coating or Insulation Thickness tcc = 0.45 mm
3
External Corrosion Coating or Insulation Density ρcc = 1440 kg/m
Concrete Coating Thickness tconc = 0 mm
3
Concrete Coating Density ρconc = 0 kg/m
Water Absorption Percentage WA% = 0%
Marine Growth Thickness tmar = 153 mm
3
Marine Growth Density ρmar = 1400 kg/m
3
Content Density ρco = 1025 kg/m
3
Seawater Density ρw = 1025 kg/m
Pipeline Steel Density ρst = 7850 kg/m3
Young's Modulus of Elasticity of Steel E = 207000 MPa
Gravity constant g = 9.805 m2/s
Maximum Wave Height Hw-max = 14.8 m
Wave Period Tp = 12.8 s
2
Wave Acceleration aw = 0 m/s
Wave Induced Velocity Uw = 4.41 m/s
Surface Current Velocity Ur = 1.4 m/s
Steady Current Velocity at Riser Span Uc = 1.4 m/s
2
Seawater Kinematic Viscosity ν = 1.03E-06 m /s
Elevation of Top Clamp ELtop = 5m
Elevation of Bottom Clamp ELbot = -13 m
Velocity Amplification Factor V.A.F. = 1
Jacket Batter (1 in X) X = 10
End Fixity = Pinned - Fixed
OUTPUT DATA
δ = 2 * π * 0.02
= 2 * 3.14 * 0.02
= 0.126
4/20/2007 Page 3 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Moment of Inertia, I
I = (π/64) * (D4 - (D - 2tc)4)
= 3.1416/64 * (406.4^4 - (406.4 - 2 * 20.8)^4)
4
= 469673591 mm
Total Diameter, Dt
Dt = D + 2tcc + 2tconc + 2tmar
= 406.4 + 2 * 0.45 + 2 * 0 + 2 * 153
= 713.30 mm
4/20/2007 Page 4 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Reduced Velocity for Onset of In-Line Oscillation due to Current, (DnV, Figure A.3), VrIL-c
VrIL-c = 1.745 m/s
Ks_1 = 0.500
Ks_2 = 0.550
VrIL-c_1 = 1.685 m/s
VrIL-c_2 = 1.765 m/s
Allowable Span Length for Dynamic In-Line Oscillation due to Current, LIL-c
LIL-c = ((α/2π)VrIL-cDt/Uca(EI/Meff)0.5))0.5
= (15.4/(2 * 3.14) * (1.75 * (713.3/1000)/1.4) * ((207000 * 10^6 * 469673590.7/10^12)/1115.67)^0.5)^0.5
= 25.36 m
Reduced Velocity for Onset of Cross-Flow Oscillation due to Current, (DnV, Figure A.5), VrCF-c
VrCF-c = 4.172 m/s
4/20/2007 Page 5 of 6
J. Ray McDermott Asia Pacific Pte. Ltd.
Reca_1 = 9.00E+05
Reca_2 = 1.00E+06
VrCF-c_1 = 4.200 m/s
VrCF-c_2 = 4.160 m/s
Allowable Span Length for Dynamic Cross Flow Oscillation due to Current, LCF-c
LCF-c = ((α/2π)VrCF-cDt/Uca(EI/Meff)0.5))0.5
= (15.4/(2 * 3.14) * (4.17 * (713.3/1000)/1.4) * ((207000 * 10^6 * 469673590.7/10^12)/1115.67)^0.5)^0.5
= 39.22 m
Reduced Velocity for Onset of Cross-Flow Oscillation due to Current + Wave, (DnV, Figure A.5), VrCF-cw
VrCF-cw = 3.870 m/s
Recwa_1 = 4.00E+06
Recwa_2 = 5.00E+06
VrCF-cw_1 = 3.870 m/s
VrCF-cw_2 = 3.860 m/s
Allowable Span Length for Dynamic Cross Flow Oscillation due to Current + Wave, LCF-cw
LCF-cw = ((α/2π)VrCF-cwDt/Ucwa(EI/Meff)0.5))0.5
= (15.4/(2 * 3.14) * (3.87 * (713.3/1000)/5.81) * ((207000 * 10^6 * 469673590.7/10^12)/1115.67)^0.5)^0.5
= 18.54 m
Pipe Frequency, f
f = (α/(2πLgov 2))(EI/Meff)0.5
= (15.4/(2 * 3.1416 * 18.54^2)) * (207000 * 10^6 * 469673590.7/10^12/1115.67)^0.5
= 2.10 Hz
Status = SAFE
4/20/2007 Page 6 of 6
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 45 of 49
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
CAESAR II
LOAD CONDITION DESCRIPTION
RUN
OPERATION + 100 YEAR
OPERATION 1
ENVIRONMENTAL LOAD
HYDROTEST + 1 YEAR
HYDROTEST 2
ENVIRONMENTAL LOAD
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 46 of 49
1
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
Table of Contents
INPUT LISTING .................................................................................................................................................... 2
MISCELLANEOUS COMPUTED DATA ..................................................................................................................... 16
Displacements 1 (OPE) W+D5+T1+P1....................................................................................................... 23
Displacements 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1............................................................................ 25
Displacements 3 (OPE) W+D2+D5+T1+P1+WIN2+WAV2............................................................................ 27
Displacements 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3............................................................................ 29
Displacements 5 (OPE) W+D4+D5+T1+P1+WIN4+WAV4............................................................................ 31
Restraint Summary 1 (OPE) W+D5+T1+P1 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1 3 (OPE)
W+D2+D5+T1+P1+WIN2+WAV2 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3 5 (OPE)
W+D4+D5+T1+P1+WIN4+WAV4.............................................................................................................................. 33
Stresses 1 (OPE) W+D5+T1+P1................................................................................................................ 38
Stresses 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1..................................................................................... 42
Stresses 3 (OPE) W+D2+D5+T1+P1+WIN2+WAV2..................................................................................... 46
Stresses 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3..................................................................................... 50
Stresses 5 (OPE) W+D4+D5+T1+P1+WIN4+WAV4..................................................................................... 54
Code Compliance Extended 1 (OPE) W+D5+T1+P1 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1 3
(OPE) W+D2+D5+T1+P1+WIN2+WAV2 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3 5 (OPE)
W+D4+D5+T1+P1+WIN4+WAV4 58
2
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
Job Description:
ANALYST: SV
PIPE DATA
-----------------------------------------------------------------------------
-----------------------------------------------------------------------------
From 10 To 20 DX= 4,000.000 mm.
PIPE
Dia= 609.600 mm. Wall= 19.100 mm. Insul= 33.500 mm. Cor= 3.0000 mm.
GENERAL
T1= 115 C P1= 18.6000 bars Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m. Insul= 725.0000 kg/cu.m.
Fluid= 40.7999992 kg/cu.m.
RESTRAINTS
Node 10 ANC Cnode 1000
DISPLACEMENTS
Node 1000 DX1= 32.400 mm. DY1= -33.700 mm. DZ1= 1.000 mm.
DX2= -164.800 mm. DY2= -38.000 mm. DZ2= -3.000 mm. DX3= -25.100 mm.
DY3= -34.600 mm. DZ3= 40.100 mm. DX4= -26.600 mm. DY4= -34.700 mm.
DZ4= -87.200 mm.
WIND
Wind Shape= .500
ALLOWABLE STRESSES
B31.8 VIII(2003) Sh1= 448 N./sq.mm. Sh2= 448 N./sq.mm.
Sh3= 448 N./sq.mm. Sh4= 448 N./sq.mm. Sh5= 448 N./sq.mm.
Sh6= 448 N./sq.mm. Sh7= 448 N./sq.mm. Sh8= 448 N./sq.mm.
Sh9= 448 N./sq.mm. Sy= 448 N./sq.mm. Fac= .5000
-----------------------------------------------------------------------------
From 20 To 30 DX= 3,500.000 mm.
BEND at "TO" end
Radius= 3,048.000 mm. (user) Bend Angle= 90.000
-----------------------------------------------------------------------------
From 30 To 40 DY= -4,500.000 mm.
BEND at "TO" end
Radius= 3,048.000 mm. (user) Bend Angle= 5.711
-----------------------------------------------------------------------------
From 40 To 50 DX= 220.000 mm. DY= -2,200.000 mm.
-----------------------------------------------------------------------------
From 50 To 60 DX= 30.000 mm. DY= -300.000 mm.
RIGID Weight= 3,650.00 N.
-----------------------------------------------------------------------------
From 60 To 70 DX= 30.000 mm. DY= -300.000 mm.
RIGID Weight= 3,650.00 N.
-----------------------------------------------------------------------------
From 70 To 80 DX= 120.000 mm. DY= -1,200.000 mm.
RESTRAINTS
Node 80 X Cnode 800 Dir Vec= .9950 .0995 .0000
Node 80 Z Cnode 800
3
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 144.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 160 To 170 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 139.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 170 To 180 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
Mat= (309)API-5LU U100 E= 203,391 N./sq.mm. v = .292
Density= 7,833.4399 kg/cu.m.
RESTRAINTS
Node 180 X Cnode 1800 Dir Vec= .9950 .0995 .0000
Node 180 Z Cnode 1800
DISPLACEMENTS
Node 1800 DX1= 12.600 mm. DY1= -35.100 mm. DZ1= -.200 mm.
DX2= -115.300 mm. DY2= -32.300 mm. DZ2= -1.800 mm. DX3= -20.500 mm.
DY3= -33.700 mm. DZ3= 24.700 mm. DX4= -25.300 mm. DY4= -34.000 mm.
DZ4= -58.400 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 133.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 180 To 190 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 128.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 190 To 200 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 122.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 200 To 210 DX= 257.300 mm. DY= -2,573.000 mm.
-----------------------------------------------------------------------------
From 210 To 220 DX= 280.900 mm. DY= -2,809.000 mm.
PIPE
Dia= 609.600 mm. Wall= 19.980 mm. Insul= 33.500 mm.
GENERAL
BEND at "TO" end
Radius= 3,048.000 mm. (user) Bend Angle= 84.745
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 117.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 220 To 230 DX= 3,403.100 mm. DZ= 1,444.500 mm.
PIPE
Dia= 609.600 mm. Wall= 19.100 mm. Insul= 33.500 mm.
GENERAL
WAVE
5
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 87.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 230 To 240 DX= 276.200 mm. DZ= 117.200 mm.
GENERAL
RIGID Weight= 3,650.00 N.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 87.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 240 To 250 DX= 276.200 mm. DZ= 117.200 mm.
GENERAL
RIGID Weight= 3,650.00 N.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 87.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 250 To 255 DX= 1,691.000 mm. DZ= 717.800 mm.
PIPE
Dia= 609.600 mm. Wall= 19.980 mm. Insul= 33.500 mm.
GENERAL
BEND at "TO" end
Radius= 3,048.000 mm. (user) Bend Angle= 29.997
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 87.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 255 To 260 DX= 2,896.800 mm. DY= -1,816.700 mm. DZ= 1,229.600 mm.
PIPE
Dia= 609.600 mm. Wall= 19.980 mm. Insul= 33.500 mm.
GENERAL
BEND at "TO" end
Radius= 3,048.000 mm. (user) Bend Angle= 29.997
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 56.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 260 To 270 DX= 2,301.300 mm. DZ= 976.800 mm.
PIPE
Dia= 609.600 mm. Wall= 19.100 mm. Insul= 96.500 mm.
GENERAL
Insul= 2,310.8000 kg/cu.m.
RESTRAINTS
Node 270 +Y K= 350 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 270 To 300 DX= 4,602.500 mm. DZ= 1,953.700 mm.
GENERAL
RESTRAINTS
Node 300 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
6
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
-----------------------------------------------------------------------------
From 300 To 310 DX= 4,602.500 mm. DZ= 1,953.700 mm.
GENERAL
RESTRAINTS
Node 310 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 310 To 320 DX= 4,326.400 mm. DZ= 1,836.400 mm.
GENERAL
RESTRAINTS
Node 320 +Y K= 658 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 320 To 330 DX= 3,221.800 mm. DZ= 1,367.600 mm.
PIPE
Dia= 609.600 mm. Wall= 19.980 mm. Insul= 96.500 mm.
GENERAL
BEND at "TO" end
Radius= 3,048.000 mm. (user) Bend Angle= 90.000
RESTRAINTS
Node 330 +Y K= 490 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 330 To 340 DX= -2,344.400 mm. DZ= 5,523.000 mm.
PIPE
Dia= 609.600 mm. Wall= 19.100 mm. Insul= 96.500 mm.
GENERAL
RESTRAINTS
Node 340 +Y K= 840 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 340 To 341 DX= -2,305.300 mm. DZ= 5,431.000 mm.
GENERAL
RESTRAINTS
Node 341 +Y K= 840 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 341 To 350 DX= -117.200 mm. DZ= 276.200 mm.
GENERAL
RIGID Weight= 3,650.00 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 350 To 360 DX= -117.200 mm. DZ= 276.200 mm.
7
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
GENERAL
RIGID Weight= 3,650.00 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 360 To 370 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 370 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 370 To 380 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 380 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 380 To 390 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 390 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 390 To 400 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 400 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 400 To 410 DX= -1,953.700 mm. DZ= 4,602.500 mm.
PIPE
Dia= 609.600 mm. Wall= 19.910 mm. Insul= 96.500 mm.
GENERAL
RESTRAINTS
Node 410 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 410 To 420 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 420 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
8
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
-----------------------------------------------------------------------------
From 420 To 430 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 430 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 430 To 440 DX= -1,953.700 mm. DZ= 4,602.500 mm.
PIPE
Dia= 609.600 mm. Wall= 19.100 mm. Insul= 96.500 mm.
GENERAL
RESTRAINTS
Node 440 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 440 To 450 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 450 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 450 To 460 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 460 ANC Cnode 4600
DISPLACEMENTS
Node 4600 DX5= 660.300 mm. DY5= .000 mm. DZ5=-1555.700 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
MATERIAL Changes:
10 20 Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m.
170 180 Mat= (309)API-5LU U100
E= 203,391 N./sq.mm. v = .292
Density= 7,833.4399 kg/cu.m.
JOBNAME: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
INPUT LISTING
BEND ELEMENTS
20 30 Radius= 3,048.000 mm. (user)
Bend Angle= 90.000
30 40 Radius= 3,048.000 mm. (user)
Bend Angle= 5.711
210 220 Radius= 3,048.000 mm. (user)
Bend Angle= 84.745
250 255 Radius= 3,048.000 mm. (user)
Bend Angle= 29.997
255 260 Radius= 3,048.000 mm. (user)
Bend Angle= 29.997
320 330 Radius= 3,048.000 mm. (user)
Bend Angle= 90.000
RIGIDS
50 60 RIGID Weight= 3,650.00 N.
60 70 RIGID Weight= 3,650.00 N.
230 240 RIGID Weight= 3,650.00 N.
240 250 RIGID Weight= 3,650.00 N.
341 350 RIGID Weight= 3,650.00 N.
350 360 RIGID Weight= 3,650.00 N.
RESTRAINTS Len MU
GAP YIELD Dir
NODE TYPE CNODE STIF1 STIF2 FORCE Vectors
-------+-------+------+----------+----------+----------+---------------------
10 ANC 1000 .000 .000 .000
80 X 800 .995 .100 .000
80 Z 800 .000 .000 1.000
80 +Y 800 .000 1.000 .000
150 X 1500 .995 .100 .000
150 Z 1500 .000 .000 1.000
180 X 1800 .995 .100 .000
180 Z 1800 .000 .000 1.000
270 +Y 350 .70 .000 1.000 .000
300 +Y 700 .70 .000 1.000 .000
310 +Y 700 .70 .000 1.000 .000
320 +Y 658 .70 .000 1.000 .000
330 +Y 490 .70 .000 1.000 .000
340 +Y 840 .70 .000 1.000 .000
341 +Y 840 .70 .000 1.000 .000
370 +Y 700 .70 .000 1.000 .000
380 +Y 700 .70 .000 1.000 .000
390 +Y 700 .70 .000 1.000 .000
400 +Y 700 .70 .000 1.000 .000
410 +Y 700 .70 .000 1.000 .000
420 +Y 700 .70 .000 1.000 .000
430 +Y 700 .70 .000 1.000 .000
440 +Y 700 .70 .000 1.000 .000
450 +Y 700 .70 .000 1.000 .000
460 ANC 4600 .000 .000 .000
10
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
DISPLACEMENTS
10 20 Node 1000 DX1= 32.400 mm. DY1= -33.700 mm.
DZ1= 1.000 mm. DX2= -164.800 mm.
DY2= -38.000 mm. DZ2= -3.000 mm.
DX3= -25.100 mm. DY3= -34.600 mm.
DZ3= 40.100 mm. DX4= -26.600 mm.
DY4= -34.700 mm. DZ4= -87.200 mm.
70 80 Node 800 DX1= 29.800 mm. DY1= -33.800 mm.
DZ1= 1.000 mm. DX2= -158.500 mm.
DY2= -37.200 mm. DZ2= -1.500 mm.
DX3= -23.800 mm. DY3= -34.400 mm.
DZ3= 38.600 mm. DX4= -27.500 mm.
DY4= -34.700 mm. DZ4= -82.800 mm.
140 150 Node 1500 DX1= 24.200 mm. DY1= -34.100 mm.
DZ1= 1.000 mm. DX2= -144.800 mm.
DY2= -35.500 mm. DZ2= 1.800 mm.
DX3= -21.000 mm. DY3= -33.900 mm.
DZ3= 35.400 mm. DX4= -29.500 mm.
DY4= -34.600 mm. DZ4= -73.200 mm.
170 180 Node 1800 DX1= 12.600 mm. DY1= -35.100 mm.
DZ1= -.200 mm. DX2= -115.300 mm.
DY2= -32.300 mm. DZ2= -1.800 mm.
DX3= -20.500 mm. DY3= -33.700 mm.
DZ3= 24.700 mm. DX4= -25.300 mm.
DY4= -34.000 mm. DZ4= -58.400 mm.
450 460 Node 4600 DX5= 660.300 mm. DY5= .000 mm.
DZ5=-1555.700 mm.
WIND/WAVE
10 20 WIND Wind Shape= .500
90 100 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 74.000
Mar. Growth Dens.= 1,400.000
100 110 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 96.000
Mar. Growth Dens.= 1,400.000
110 120 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 119.000
Mar. Growth Dens.= 1,400.000
120 130 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 153.000
Mar. Growth Dens.= 1,400.000
130 140 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 153.000
Mar. Growth Dens.= 1,400.000
11
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
COORDINATE REPORT
/--------------------(mm.)----------------------/
NODE X Y Z
10 .0000 13500.0000 .0000
20 4000.0000 13500.0000 .0000
30 7500.0000 13500.0000 .0000
40 7500.0000 9000.0000 .0000
50 7720.0000 6800.0000 .0000
60 7750.0000 6500.0000 .0000
70 7780.0000 6200.0000 .0000
80 7900.0000 5000.0000 .0000
90 8400.0000 .0000 .0000
100 8500.0000 -1000.0000 .0000
110 8600.0000 -2000.0000 .0000
120 8700.0000 -3000.0000 .0000
130 8850.0000 -4500.0000 .0000
140 9350.0000 -9500.0000 .0000
150 9700.0000 -13000.0000 .0000
160 10200.0000 -18000.0000 .0000
170 10700.0000 -23000.0000 .0000
180 11200.0000 -28000.0000 .0000
190 11700.0000 -33000.0000 .0000
200 12200.0000 -38000.0000 .0000
210 12457.2998 -40573.0000 .0000
220 12738.2002 -43382.0000 .0000
230 16141.3008 -43382.0000 1444.5000
240 16417.5000 -43382.0000 1561.7000
250 16693.6992 -43382.0000 1678.8999
255 18384.6992 -43382.0000 2396.7000
260 21281.5000 -45198.6992 3626.2998
270 23582.8008 -45198.6992 4603.0996
300 28185.3008 -45198.6992 6556.7998
310 32787.8008 -45198.6992 8510.5000
320 37114.1992 -45198.6992 10346.9004
330 40336.0000 -45198.6992 11714.5000
340 37991.6016 -45198.6992 17237.5000
341 35686.3008 -45198.6992 22668.5000
350 35569.1016 -45198.6992 22944.6992
360 35451.9023 -45198.6992 23220.8984
370 33498.2031 -45198.6992 27823.3984
380 31544.5039 -45198.6992 32425.8984
390 29590.8047 -45198.6992 37028.3984
400 27637.1055 -45198.6992 41630.8984
410 25683.4062 -45198.6992 46233.3984
420 23729.7070 -45198.6992 50835.8984
430 21776.0078 -45198.6992 55438.3984
440 19822.3086 -45198.6992 60040.8984
450 17868.6094 -45198.6992 64643.3984
460 15914.9092 -45198.6992 69245.8984
16
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
BEND DATA:
250. 255. 2.843 0.481 0.102 0.000E+00 0.000E+00 0.000E+00 .000 .000
255. 260. 2.843 0.481 0.102 0.000E+00 0.000E+00 0.000E+00 .000 .000
260. 270. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
270. 300. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
300. 310. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
310. 320. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
320. 330. 2.843 4.851 0.102 0.000E+00 0.000E+00 0.000E+00 .000 .000
330. 340. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
340. 341. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
341. 350. 12.165 8.489 0.103 0.000E+00 0.000E+00 0.000E+00 NA NA
350. 360. 12.165 8.489 0.103 0.000E+00 0.000E+00 0.000E+00 NA NA
360. 370. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
370. 380. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
380. 390. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
390. 400. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
400. 410. 2.833 4.851 0.102 0.000E+00 0.000E+00 0.000E+00 .000 .000
410. 420. 2.833 4.851 0.102 0.000E+00 0.000E+00 0.000E+00 .000 .000
420. 430. 2.833 4.851 0.102 0.000E+00 0.000E+00 0.000E+00 .000 .000
430. 440. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
440. 450. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
450. 460. 2.722 4.851 0.103 0.000E+00 0.000E+00 0.000E+00 .000 .000
10. 20. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
20. 30. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
30. 40. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
40. 50. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
50. 60. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
60. 70. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
70. 80. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
80. 90. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
90. 100. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
100. 110. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
110. 120. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
120. 130. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
130. 140. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
140. 150. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
150. 160. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
160. 170. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
170. 180. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
180. 190. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
190. 200. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
200. 210. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
210. 220. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
220. 230. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
230. 240. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
240. 250. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
250. 255. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
255. 260. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
260. 270. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
18
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
270. 300. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
300. 310. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
310. 320. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
320. 330. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
330. 340. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
340. 341. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
341. 350. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
350. 360. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
360. 370. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
370. 380. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
380. 390. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
390. 400. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
400. 410. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
410. 420. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
420. 430. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
430. 440. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
440. 450. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
450. 460. 0.0011 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
WIND LOADING #: 1
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... 1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 2
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... -1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 3
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... 1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
20
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
WIND LOADING #: 4
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... -1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WAVE VECTOR 1
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and 1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1400.000
2 22800.000 1200.000
3 45600.000 700.000
4 0.000 0.000
5 0.000 0.000
21
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 2
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and -1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: -1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1400.000
2 22800.000 1200.000
3 45600.000 700.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 3
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and 0.000 1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 0.000 1.000
22
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
WAVE VECTOR 4
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and 0.000 -1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 0.000 -1.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1400.000
2 22800.000 1200.000
3 45600.000 700.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
23
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
Rigid X;
80 Rigid Z;
Rigid +Y
1 (OPE) 35425 -115579 -46469 0 0 0
2 (OPE) 121340 -165254 -39477 0 0 0
3 (OPE) -50519 -74550 -50245 0 0 0
4 (OPE) 26547 -111909 -4455 0 0 0
5 (OPE) 37491 -106062 -87525 0 0 0
MAX 121340/ 2 165254/ 2 87525/ 5 0/ 1 0/ 1 0/ 1
Rigid X;
150
Rigid Z
1 (OPE) -3686 -369 42954 0 0 0
2 (OPE) 16674 1667 18459 0 0 0
3 (OPE) -50818 -5082 50638 0 0 0
4 (OPE) 12798 1280 90084 0 0 0
5 (OPE) -21218 -2122 -6942 0 0 0
MAX 50818/ 3 5082/ 3 90084/ 4 0/ 1 0/ 1 0/ 1
Rigid X;
180
Rigid Z
1 (OPE) -12202 -1220 -38816 0 0 0
2 (OPE) 188782 18878 7743 0 0 0
3 (OPE) -172965 -17297 -57356 0 0 0
4 (OPE) -43993 -4399 130102 0 0 0
5 (OPE) 5447 545 -205598 0 0 0
MAX 188782/ 2 18878/ 2 205598/ 5 0/ 1 0/ 1 0/ 1
270 Flex +Y
1 (OPE) 3802 -15316 -10025 0 0 0
2 (OPE) 0 0 0 0 0 0
3 (OPE) 625 -32448 -22705 0 0 0
4 (OPE) 6472 -23972 -15482 0 0 0
34
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
300 Flex +Y
1 (OPE) 5837 -22559 -14673 0 0 0
2 (OPE) 0 0 0 0 0 0
3 (OPE) 4264 -43640 -30249 0 0 0
4 (OPE) 10431 -37808 -24323 0 0 0
5 (OPE) 3237 -14199 -9398 0 0 0
MAX 10431/ 4 43640/ 3 30249/ 3 0/ 1 0/ 1 0/ 1
310 Flex +Y
1 (OPE) 4222 -15959 -10343 0 0 0
2 (OPE) 633 -1567 -896 0 0 0
3 (OPE) 3759 -26834 -18404 0 0 0
4 (OPE) 8763 -31511 -20243 0 0 0
5 (OPE) 0 0 0 0 0 0
MAX 8763/ 4 31511/ 4 20243/ 4 0/ 1 0/ 1 0/ 1
320 Flex +Y
1 (OPE) 2797 -10433 -6746 0 0 0
2 (OPE) 1604 -4165 -2434 0 0 0
3 (OPE) 2416 -14775 -10056 0 0 0
4 (OPE) 7636 -27349 -17556 0 0 0
5 (OPE) 0 0 0 0 0 0
MAX 7636/ 4 27349/ 4 17556/ 4 0/ 1 0/ 1 0/ 1
330 Flex +Y
1 (OPE) 2291 -7316 -4580 0 0 0
2 (OPE) 1861 -4348 -2408 0 0 0
3 (OPE) 2024 -9845 -6588 0 0 0
4 (OPE) 4797 -14083 -8612 0 0 0
5 (OPE) 0 0 0 0 0 0
MAX 4797/ 4 14083/ 4 8612/ 4 0/ 1 0/ 1 0/ 1
340 Flex +Y
1 (OPE) 5067 -14750 -8997 0 0 0
2 (OPE) 3306 -6998 -3614 0 0 0
3 (OPE) 4796 -21932 -14584 0 0 0
4 (OPE) 6986 -18250 -10695 0 0 0
5 (OPE) 1112 -3904 -2496 0 0 0
MAX 6986/ 4 21932/ 3 14584/ 3 0/ 1 0/ 1 0/ 1
341 Flex +Y
1 (OPE) 6769 -17531 -10236 0 0 0
2 (OPE) 2862 -5304 -2365 0 0 0
3 (OPE) 6577 -29578 -19632 0 0 0
4 (OPE) 5716 -12976 -7059 0 0 0
5 (OPE) 6019 -19786 -12474 0 0 0
35
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
370 Flex +Y
1 (OPE) 6158 -15013 -8516 0 0 0
2 (OPE) 1492 -2573 -1009 0 0 0
3 (OPE) 5791 -27531 -18381 0 0 0
4 (OPE) 4568 -9675 -4999 0 0 0
5 (OPE) 6429 -20527 -12850 0 0 0
MAX 6429/ 5 27531/ 3 18381/ 3 0/ 1 0/ 1 0/ 1
380 Flex +Y
1 (OPE) 6142 -14613 -8180 0 0 0
2 (OPE) 756 -1259 -453 0 0 0
3 (OPE) 5457 -28151 -18935 0 0 0
4 (OPE) 4760 -9804 -4943 0 0 0
5 (OPE) 6381 -20240 -12650 0 0 0
MAX 6381/ 5 28151/ 3 18935/ 3 0/ 1 0/ 1 0/ 1
390 Flex +Y
1 (OPE) 6007 -14238 -7953 0 0 0
2 (OPE) 324 -531 -183 0 0 0
3 (OPE) 5004 -28170 -19074 0 0 0
4 (OPE) 5073 -10396 -5218 0 0 0
5 (OPE) 5933 -18931 -11849 0 0 0
MAX 6007/ 1 28170/ 3 19074/ 3 0/ 1 0/ 1 0/ 1
400 Flex +Y
1 (OPE) 5883 -14133 -7953 0 0 0
2 (OPE) 182 -298 -102 0 0 0
3 (OPE) 4676 -28199 -19177 0 0 0
4 (OPE) 5336 -11093 -5641 0 0 0
5 (OPE) 5509 -17829 -11199 0 0 0
MAX 5883/ 1 28199/ 3 19177/ 3 0/ 1 0/ 1 0/ 1
410 Flex +Y
1 (OPE) 5732 -14174 -8099 0 0 0
2 (OPE) 203 -337 -122 0 0 0
3 (OPE) 4553 -28235 -19232 0 0 0
4 (OPE) 5414 -11627 -6077 0 0 0
5 (OPE) 5203 -17165 -10830 0 0 0
MAX 5732/ 1 28235/ 3 19232/ 3 0/ 1 0/ 1 0/ 1
420 Flex +Y
1 (OPE) 5413 -13993 -8164 0 0 0
2 (OPE) 263 -455 -179 0 0 0
3 (OPE) 4597 -27741 -18867 0 0 0
4 (OPE) 5183 -11721 -6360 0 0 0
5 (OPE) 4911 -16552 -10494 0 0 0
MAX 5413/ 1 27741/ 3 18867/ 3 0/ 1 0/ 1 0/ 1
36
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
430 Flex +Y
1 (OPE) 4752 -13049 -7800 0 0 0
2 (OPE) 297 -548 -244 0 0 0
3 (OPE) 4634 -25735 -17408 0 0 0
4 (OPE) 4524 -11012 -6242 0 0 0
5 (OPE) 4433 -15273 -9729 0 0 0
MAX 4752/ 1 25735/ 3 17408/ 3 0/ 1 0/ 1 0/ 1
440 Flex +Y
1 (OPE) 3595 -10663 -6541 0 0 0
2 (OPE) 276 -574 -292 0 0 0
3 (OPE) 4268 -20899 -13993 0 0 0
4 (OPE) 3351 -9021 -5352 0 0 0
5 (OPE) 3532 -12430 -7951 0 0 0
MAX 4268/ 3 20899/ 3 13993/ 3 0/ 1 0/ 1 0/ 1
450 Flex +Y
1 (OPE) 1917 -6256 -3937 0 0 0
2 (OPE) 177 -453 -263 0 0 0
3 (OPE) 2873 -12142 -7999 0 0 0
4 (OPE) 1725 -5306 -3289 0 0 0
5 (OPE) 2026 -7272 -4670 0 0 0
MAX 2873/ 3 12142/ 3 7999/ 3 0/ 1 0/ 1 0/ 1
Displ.
800
Reaction
1 (OPE) 35425 -115579 -46469 0 0 0
2 (OPE) 121340 -165254 -39477 0 0 0
3 (OPE) -50519 -74550 -50245 0 0 0
4 (OPE) 26547 -111908 -4455 0 0 0
5 (OPE) 37491 -106062 -87525 0 0 0
MAX 121340/ 2 165254/ 2 87525/ 5 0/ 1 0/ 1 0/ 1
Displ.
1000
Reaction
1 (OPE) -27519 6823 26444 0 0 0
2 (OPE) -56598 15597 24121 0 0 0
3 (OPE) 3184 -4069 28503 0 0 0
4 (OPE) -23461 5191 26973 0 0 0
5 (OPE) -29389 7807 25594 0 0 0
37
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
Displ.
1500
Reaction
1 (OPE) -3686 -369 42954 0 0 0
2 (OPE) 16674 1667 18459 0 0 0
3 (OPE) -50818 -5082 50638 0 0 0
4 (OPE) 12798 1280 90084 0 0 0
5 (OPE) -21218 -2122 -6942 0 0 0
MAX 50818/ 3 5082/ 3 90084/ 4 0/ 1 0/ 1 0/ 1
Displ.
1800
Reaction
1 (OPE) -12202 -1220 -38816 0 0 0
2 (OPE) 188782 18878 7743 0 0 0
3 (OPE) -172965 -17297 -57356 0 0 0
4 (OPE) -43993 -4399 130102 0 0 0
5 (OPE) 5447 545 -205598 0 0 0
MAX 188782/ 2 18878/ 2 205598/ 5 0/ 1 0/ 1 0/ 1
Displ.
4600
Reaction
1 (OPE) -55472 -13094 152152 0 0 0
2 (OPE) 48929 931 41011 0 0 0
3 (OPE) -150390 -27318 260343 0 0 0
4 (OPE) -66780 -10663 199263 0 0 0
5 (OPE) -49707 -15681 107333 0 0 0
MAX 150390/ 3 27318/ 3 260343/ 3 0/ 1 0/ 1 0/ 1
38
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:24:14
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-OPN
Licensed To: B & W ID: 13709
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 10 29.68 224.07 13.2 20 29.68 224.07 13.2
2 (OPE) 10 29.68 224.07 13.2 20 29.68 224.07 13.2
3 (OPE) 10 29.68 224.07 13.2 20 29.68 224.07 13.2
4 (OPE) 10 29.68 224.07 13.2 20 29.68 224.07 13.2
5 (OPE) 10 29.68 224.07 13.2 20 29.68 224.07 13.2
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (OPE) 20 29.68 224.07 13.2 30 67.03 403.33 16.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 80 88.44 403.33 21.9 90 69.25 403.33 17.2
2 (OPE) 80 107.53 403.33 26.7 90 67.02 403.33 16.6
3 (OPE) 80 97.55 403.33 24.2 90 77.90 403.33 19.3
4 (OPE) 80 81.33 403.33 20.2 90 98.22 403.33 24.4
5 (OPE) 80 93.88 403.33 23.3 90 58.22 403.33 14.4
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 130 85.67 403.33 21.2 140 75.66 403.33 18.8
4 (OPE) 130 96.53 403.33 23.9 140 62.29 403.33 15.4
5 (OPE) 130 74.89 403.33 18.6 140 76.62 403.33 19.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (OPE) 180 266.36 403.33 66.0 190 151.50 403.33 37.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 240 0.00 0.00 0.0 250 0.00 0.00 0.0
2 (OPE) 240 0.00 0.00 0.0 250 0.00 0.00 0.0
3 (OPE) 240 0.00 0.00 0.0 250 0.00 0.00 0.0
4 (OPE) 240 0.00 0.00 0.0 250 0.00 0.00 0.0
5 (OPE) 240 0.00 0.00 0.0 250 0.00 0.00 0.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 300 52.61 403.33 13.0 310 128.21 403.33 31.8
4 (OPE) 300 71.36 403.33 17.7 310 50.68 403.33 12.6
5 (OPE) 300 94.69 403.33 23.5 310 121.08 403.33 30.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (OPE) 341 0.00 0.00 0.0 350 0.00 0.00 0.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 400 74.38 403.33 18.4 410 64.41 403.33 16.0
2 (OPE) 400 242.47 403.33 60.1 410 234.10 403.33 58.0
3 (OPE) 400 76.10 403.33 18.9 410 90.96 403.33 22.6
4 (OPE) 400 109.92 403.33 27.3 410 94.05 403.33 23.3
5 (OPE) 400 30.55 403.33 7.6 410 27.08 403.33 6.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 450 65.07 403.33 16.1 460 29.88 403.33 7.4
4 (OPE) 450 41.22 403.33 10.2 460 28.58 403.33 7.1
5 (OPE) 450 31.97 403.33 7.9 460 27.64 403.33 6.9
1
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
Table of Contents
INPUT LISTING .................................................................................................................................................... 2
MISCELLANEOUS COMPUTED DATA ..................................................................................................................... 15
Displacements 1 (HYD) W+D5+T1+HP....................................................................................................... 22
Displacements 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1............................................................................ 24
Displacements 3 (HYD) W+D2+D5+T1+HP+WIN2+WAV2............................................................................ 26
Displacements 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3............................................................................ 28
Displacements 5 (HYD) W+D4+D5+T1+HP+WIN4+WAV4............................................................................ 30
Restraint Summary 1 (HYD) W+D5+T1+HP 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1 3 (HYD)
W+D2+D5+T1+HP+WIN2+WAV2 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3 5 (HYD)
W+D4+D5+T1+HP+WIN4+WAV4.............................................................................................................................. 32
Stresses 1 (HYD) W+D5+T1+HP................................................................................................................ 37
Stresses 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1..................................................................................... 41
Stresses 3 (HYD) W+D2+D5+T1+HP+WIN2+WAV2..................................................................................... 45
Stresses 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3..................................................................................... 49
Stresses 5 (HYD) W+D4+D5+T1+HP+WIN4+WAV4..................................................................................... 53
Code Compliance Extended 1 (HYD) W+D5+T1+HP 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1 3
(HYD) W+D2+D5+T1+HP+WIN2+WAV2 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3 5 (HYD)
W+D4+D5+T1+HP+WIN4+WAV4 57
2
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
Job Description:
Job Description:
ANALYST: SV
PIPE DATA
-----------------------------------------------------------------------------
-----------------------------------------------------------------------------
From 10 To 20 DX= 4,000.000 mm.
PIPE
Dia= 609.600 mm. Wall= 19.100 mm. Insul= 33.500 mm.
GENERAL
T1= 29 C PHyd= 138.7500 bars Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m. Insul= 725.0000 kg/cu.m.
Fluid=1025.0000000 kg/cu.m.
RESTRAINTS
Node 10 ANC Cnode 1000
DISPLACEMENTS
Node 1000 DX1= 9.200 mm. DY1= -36.800 mm. DZ1= .700 mm.
DX2= -109.000 mm. DY2= -38.700 mm. DZ2= -1.900 mm. DX3= -26.300 mm.
DY3= -37.400 mm. DZ3= 24.600 mm. DX4= -26.400 mm. DY4= -37.000 mm.
DZ4= -47.400 mm.
WIND
Wind Shape= .500
ALLOWABLE STRESSES
B31.8 VIII(2003) Sh1= 448 N./sq.mm. Sh2= 448 N./sq.mm.
Sh3= 448 N./sq.mm. Sh4= 448 N./sq.mm. Sh5= 448 N./sq.mm.
Sh6= 448 N./sq.mm. Sh7= 448 N./sq.mm. Sh8= 448 N./sq.mm.
Sh9= 448 N./sq.mm. Sy= 448 N./sq.mm. Fac= .5000
-----------------------------------------------------------------------------
From 20 To 30 DX= 3,500.000 mm.
BEND at "TO" end
Radius= 3,048.000 mm. (user) Bend Angle= 90.000
-----------------------------------------------------------------------------
From 30 To 40 DY= -4,500.000 mm.
BEND at "TO" end
Radius= 3,048.000 mm. (user) Bend Angle= 5.711
-----------------------------------------------------------------------------
From 40 To 50 DX= 220.000 mm. DY= -2,200.000 mm.
-----------------------------------------------------------------------------
From 50 To 60 DX= 30.000 mm. DY= -300.000 mm.
RIGID Weight= 3,650.00 N.
-----------------------------------------------------------------------------
From 60 To 70 DX= 30.000 mm. DY= -300.000 mm.
RIGID Weight= 3,650.00 N.
-----------------------------------------------------------------------------
From 70 To 80 DX= 120.000 mm. DY= -1,200.000 mm.
RESTRAINTS
3
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 170 To 180 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
Mat= (309)API-5LU U100 E= 203,391 N./sq.mm. v = .300
Density= 7,833.4399 kg/cu.m.
RESTRAINTS
Node 180 X Cnode 1800 Dir Vec= .9950 .0995 .0000
Node 180 Z Cnode 1800
DISPLACEMENTS
Node 1800 DX1= -1.600 mm. DY1= -37.300 mm. DZ1= -.400 mm.
DX2= -73.900 mm. DY2= -34.500 mm. DZ2= -1.300 mm. DX3= -21.700 mm.
DY3= -36.400 mm. DZ3= 14.400 mm. DX4= -24.200 mm. DY4= -36.100 mm.
DZ4= -29.900 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 180 To 190 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 190 To 200 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 200 To 210 DX= 257.300 mm. DY= -2,573.000 mm.
-----------------------------------------------------------------------------
From 210 To 220 DX= 280.900 mm. DY= -2,809.000 mm.
PIPE
Dia= 609.600 mm. Wall= 19.980 mm. Insul= 33.500 mm.
GENERAL
BEND at "TO" end
Radius= 3,048.000 mm. (user) Bend Angle= 84.745
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 220 To 230 DX= 3,403.100 mm. DZ= 1,444.500 mm.
PIPE
Dia= 609.600 mm. Wall= 19.100 mm. Insul= 33.500 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 230 To 240 DX= 276.200 mm. DZ= 117.200 mm.
GENERAL
RIGID Weight= 3,650.00 N.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 240 To 250 DX= 276.200 mm. DZ= 117.200 mm.
GENERAL
5
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 390 To 400 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 400 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 400 To 410 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 410 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 410 To 420 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 420 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 420 To 430 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 430 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 430 To 440 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 440 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 440 To 450 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 450 +Y K= 700 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 450 To 460 DX= -1,953.700 mm. DZ= 4,602.500 mm.
GENERAL
RESTRAINTS
Node 460 ANC Cnode 4600
DISPLACEMENTS
Node 4600 DX5= 47.300 mm. DY5= .000 mm. DZ5= -111.400 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
8
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
MATERIAL Changes:
10 20 Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m.
170 180 Mat= (309)API-5LU U100
E= 203,391 N./sq.mm. v = .300
Density= 7,833.4399 kg/cu.m.
JOBNAME: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
BEND ELEMENTS
20 30 Radius= 3,048.000 mm. (user)
Bend Angle= 90.000
30 40 Radius= 3,048.000 mm. (user)
Bend Angle= 5.711
210 220 Radius= 3,048.000 mm. (user)
Bend Angle= 84.745
250 255 Radius= 3,048.000 mm. (user)
Bend Angle= 29.997
255 260 Radius= 3,048.000 mm. (user)
Bend Angle= 29.997
320 330 Radius= 3,048.000 mm. (user)
Bend Angle= 90.000
RIGIDS
50 60 RIGID Weight= 3,650.00 N.
60 70 RIGID Weight= 3,650.00 N.
230 240 RIGID Weight= 3,650.00 N.
240 250 RIGID Weight= 3,650.00 N.
341 350 RIGID Weight= 3,650.00 N.
350 360 RIGID Weight= 3,650.00 N.
RESTRAINTS Len MU
GAP YIELD Dir
NODE TYPE CNODE STIF1 STIF2 FORCE Vectors
-------+-------+------+----------+----------+----------+---------------------
10 ANC 1000 .000 .000 .000
80 X 800 .995 .100 .000
80 Z 800 .000 .000 1.000
80 +Y 800 .000 1.000 .000
150 X 1500 .995 .100 .000
150 Z 1500 .000 .000 1.000
180 X 1800 .995 .100 .000
180 Z 1800 .000 .000 1.000
9
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
DISPLACEMENTS
10 20 Node 1000 DX1= 9.200 mm. DY1= -36.800 mm.
DZ1= .700 mm. DX2= -109.000 mm.
DY2= -38.700 mm. DZ2= -1.900 mm.
DX3= -26.300 mm. DY3= -37.400 mm.
DZ3= 24.600 mm. DX4= -26.400 mm.
DY4= -37.000 mm. DZ4= -47.400 mm.
70 80 Node 800 DX1= 7.600 mm. DY1= -36.800 mm.
DZ1= .900 mm. DX2= -104.500 mm.
DY2= -38.100 mm. DZ2= -.700 mm.
DX3= -25.200 mm. DY3= -37.200 mm.
DZ3= 23.800 mm. DX4= -26.800 mm.
DY4= -36.900 mm. DZ4= -44.500 mm.
140 150 Node 1500 DX1= 4.200 mm. DY1= -36.900 mm.
DZ1= 1.400 mm. DX2= -94.800 mm.
DY2= -36.800 mm. DZ2= 1.800 mm.
DX3= -22.900 mm. DY3= -36.700 mm.
DZ3= 22.000 mm. DX4= -27.600 mm.
DY4= -36.700 mm. DZ4= -38.300 mm.
170 180 Node 1800 DX1= -1.600 mm. DY1= -37.300 mm.
DZ1= -.400 mm. DX2= -73.900 mm.
DY2= -34.500 mm. DZ2= -1.300 mm.
DX3= -21.700 mm. DY3= -36.400 mm.
DZ3= 14.400 mm. DX4= -24.200 mm.
DY4= -36.100 mm. DZ4= -29.900 mm.
450 460 Node 4600 DX5= 47.300 mm. DY5= .000 mm.
DZ5= -111.400 mm.
WIND/WAVE
10 20 WIND Wind Shape= .500
90 100 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
100 110 WAVE Drag Coef= .700
10
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
COORDINATE REPORT
/--------------------(mm.)----------------------/
NODE X Y Z
10 .0000 13500.0000 .0000
20 4000.0000 13500.0000 .0000
30 7500.0000 13500.0000 .0000
40 7500.0000 9000.0000 .0000
50 7720.0000 6800.0000 .0000
60 7750.0000 6500.0000 .0000
70 7780.0000 6200.0000 .0000
80 7900.0000 5000.0000 .0000
90 8400.0000 .0000 .0000
100 8500.0000 -1000.0000 .0000
110 8600.0000 -2000.0000 .0000
120 8700.0000 -3000.0000 .0000
130 8850.0000 -4500.0000 .0000
140 9350.0000 -9500.0000 .0000
150 9700.0000 -13000.0000 .0000
160 10200.0000 -18000.0000 .0000
170 10700.0000 -23000.0000 .0000
180 11200.0000 -28000.0000 .0000
190 11700.0000 -33000.0000 .0000
200 12200.0000 -38000.0000 .0000
210 12457.2998 -40573.0000 .0000
220 12738.2002 -43382.0000 .0000
230 16141.3008 -43382.0000 1444.5000
240 16417.5000 -43382.0000 1561.7000
250 16693.6992 -43382.0000 1678.8999
255 18384.6992 -43382.0000 2396.7000
260 21281.5000 -45198.6992 3626.2998
270 23582.8008 -45198.6992 4603.0996
280 28185.3008 -45198.6992 6556.7998
290 32787.8008 -45198.6992 8510.5000
14
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
BEND DATA:
10. 20. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
20. 30. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
30. 40. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
40. 50. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
50. 60. 12.106 0.842 2.577 0.000E+00 0.000E+00 0.000E+00 NA NA
60. 70. 12.106 0.842 2.577 0.000E+00 0.000E+00 0.000E+00 NA NA
70. 80. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
80. 90. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
90. 100. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
100. 110. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
110. 120. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
120. 130. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
130. 140. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
140. 150. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
150. 160. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
160. 170. 2.728 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
170. 180. 2.722 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
180. 190. 2.722 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
190. 200. 2.722 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
200. 210. 2.722 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
210. 220. 2.843 0.481 2.562 0.000E+00 0.000E+00 0.000E+00 .000 .000
220. 230. 2.722 0.481 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
230. 240. 12.165 0.842 2.577 0.000E+00 0.000E+00 0.000E+00 NA NA
240. 250. 12.165 0.842 2.577 0.000E+00 0.000E+00 0.000E+00 NA NA
16
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
250. 255. 2.843 0.481 2.562 0.000E+00 0.000E+00 0.000E+00 .000 .000
255. 260. 2.843 0.481 2.562 0.000E+00 0.000E+00 0.000E+00 .000 .000
260. 270. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
270. 280. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
280. 290. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
290. 320. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
320. 330. 2.843 4.851 2.562 0.000E+00 0.000E+00 0.000E+00 .000 .000
330. 340. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
340. 341. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
341. 350. 12.165 8.489 2.577 0.000E+00 0.000E+00 0.000E+00 NA NA
350. 360. 12.165 8.489 2.577 0.000E+00 0.000E+00 0.000E+00 NA NA
360. 370. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
370. 380. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
380. 390. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
390. 400. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
400. 410. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
410. 420. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
420. 430. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
430. 440. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
440. 450. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
450. 460. 2.722 4.851 2.577 0.000E+00 0.000E+00 0.000E+00 .000 .000
10. 20. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
20. 30. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
30. 40. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
40. 50. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
50. 60. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
60. 70. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
70. 80. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
80. 90. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
90. 100. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
100. 110. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
110. 120. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
120. 130. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
130. 140. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
140. 150. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
150. 160. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
160. 170. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
170. 180. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
180. 190. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
190. 200. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
200. 210. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
210. 220. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
220. 230. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
230. 240. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
240. 250. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
250. 255. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
255. 260. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
260. 270. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
17
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
270. 280. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
280. 290. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
290. 320. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
320. 330. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
330. 340. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
340. 341. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
341. 350. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
350. 360. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
360. 370. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
370. 380. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
380. 390. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
390. 400. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
400. 410. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
410. 420. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
420. 430. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
430. 440. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
440. 450. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
450. 460. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
WIND LOADING #: 1
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... 1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 2
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... -1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 3
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... 1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
19
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
WIND LOADING #: 4
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... -1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WAVE VECTOR 1
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and 1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1100.000
2 22800.000 800.000
3 45600.000 300.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
20
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 2
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and -1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: -1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1100.000
2 22800.000 800.000
3 45600.000 300.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 3
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and 0.000 1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 0.000 1.000
Phase Specified at Origin
21
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
WAVE VECTOR 4
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and 0.000 -1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 0.000 -1.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1100.000
2 22800.000 800.000
3 45600.000 300.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
22
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
Rigid X;
80 Rigid Z;
Rigid +Y
1 (HYD) 19473 -227297 -1005 0 0 0
2 (HYD) 36233 -220731 -658 0 0 0
3 (HYD) -1169 -228106 -465 0 0 0
4 (HYD) 18162 -221638 12761 0 0 0
5 (HYD) 19135 -225003 -14063 0 0 0
MAX 36233/ 2 228106/ 3 14063/ 5 0/ 1 0/ 1 0/ 1
Rigid X;
150
Rigid Z
1 (HYD) -1372 -137 -7036 0 0 0
2 (HYD) 12157 1216 -7259 0 0 0
3 (HYD) -23918 -2392 -10934 0 0 0
4 (HYD) -5127 -513 9229 0 0 0
5 (HYD) -5734 -573 -26271 0 0 0
MAX 23918/ 3 2392/ 3 26271/ 5 0/ 1 0/ 1 0/ 1
Rigid X;
180
Rigid Z
1 (HYD) -2929 -293 15534 0 0 0
2 (HYD) -1477 -148 14059 0 0 0
3 (HYD) 7884 788 21728 0 0 0
4 (HYD) -1391 -139 19344 0 0 0
5 (HYD) 2155 216 14917 0 0 0
MAX 7884/ 3 788/ 3 21728/ 3 0/ 1 0/ 1 0/ 1
270 Flex +Y
1 (HYD) -8645 -12371 -505 0 0 0
2 (HYD) -12276 -17576 824 0 0 0
3 (HYD) -9384 -13422 -460 0 0 0
4 (HYD) -11305 -16845 3351 0 0 0
33
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
280 Flex +Y
1 (HYD) -1947 -27229 -18960 0 0 0
2 (HYD) 2053 -31936 -22260 0 0 0
3 (HYD) -6750 -27020 -17668 0 0 0
4 (HYD) -1571 -31271 -21833 0 0 0
5 (HYD) -1881 -29368 -20472 0 0 0
MAX 6750/ 3 31936/ 2 22260/ 2 0/ 1 0/ 1 0/ 1
290 Flex +Y
1 (HYD) 3775 -27940 -19190 0 0 0
2 (HYD) 5641 -28848 -19390 0 0 0
3 (HYD) 1170 -26892 -18788 0 0 0
4 (HYD) 4566 -28826 -19654 0 0 0
5 (HYD) 3565 -27705 -19063 0 0 0
MAX 5641/ 2 28848/ 2 19654/ 4 0/ 1 0/ 1 0/ 1
320 Flex +Y
1 (HYD) 5088 -26481 -17825 0 0 0
2 (HYD) 5759 -25138 -16627 0 0 0
3 (HYD) 3440 -25333 -17397 0 0 0
4 (HYD) 5306 -25522 -17059 0 0 0
5 (HYD) 4703 -25158 -16971 0 0 0
MAX 5759/ 2 26481/ 1 17825/ 1 0/ 1 0/ 1 0/ 1
330 Flex +Y
1 (HYD) 5520 -18628 -11813 0 0 0
2 (HYD) 5562 -17235 -10706 0 0 0
3 (HYD) 4665 -18250 -11893 0 0 0
4 (HYD) 5458 -17680 -11107 0 0 0
5 (HYD) 5128 -17631 -11226 0 0 0
MAX 5562/ 2 18628/ 1 11893/ 3 0/ 1 0/ 1 0/ 1
340 Flex +Y
1 (HYD) 10446 -31027 -19042 0 0 0
2 (HYD) 10553 -29404 -17672 0 0 0
3 (HYD) 9315 -30918 -19535 0 0 0
4 (HYD) 10433 -30082 -18291 0 0 0
5 (HYD) 9899 -29913 -18452 0 0 0
MAX 10553/ 2 31027/ 1 19535/ 3 0/ 1 0/ 1 0/ 1
341 Flex +Y
1 (HYD) 11414 -31067 -18511 0 0 0
2 (HYD) 11637 -30408 -17823 0 0 0
3 (HYD) 10750 -31561 -19301 0 0 0
4 (HYD) 11529 -30924 -18321 0 0 0
5 (HYD) 11138 -30802 -18462 0 0 0
34
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
370 Flex +Y
1 (HYD) 9478 -26021 -15554 0 0 0
2 (HYD) 9671 -25794 -15247 0 0 0
3 (HYD) 9125 -26598 -16229 0 0 0
4 (HYD) 9566 -26143 -15601 0 0 0
5 (HYD) 9379 -26143 -15714 0 0 0
MAX 9671/ 2 26598/ 3 16229/ 3 0/ 1 0/ 1 0/ 1
380 Flex +Y
1 (HYD) 9058 -26026 -15806 0 0 0
2 (HYD) 9210 -25856 -15580 0 0 0
3 (HYD) 8785 -26607 -16423 0 0 0
4 (HYD) 9092 -26172 -15905 0 0 0
5 (HYD) 9004 -26250 -16017 0 0 0
MAX 9210/ 2 26607/ 3 16423/ 3 0/ 1 0/ 1 0/ 1
390 Flex +Y
1 (HYD) 8585 -26192 -16200 0 0 0
2 (HYD) 8698 -25981 -15972 0 0 0
3 (HYD) 8341 -26731 -16750 0 0 0
4 (HYD) 8568 -26290 -16287 0 0 0
5 (HYD) 8545 -26417 -16399 0 0 0
MAX 8698/ 2 26731/ 3 16750/ 3 0/ 1 0/ 1 0/ 1
400 Flex +Y
1 (HYD) 8198 -26568 -16693 0 0 0
2 (HYD) 8293 -26292 -16430 0 0 0
3 (HYD) 7961 -27066 -17192 0 0 0
4 (HYD) 8154 -26608 -16746 0 0 0
5 (HYD) 8167 -26759 -16857 0 0 0
MAX 8293/ 2 27066/ 3 17192/ 3 0/ 1 0/ 1 0/ 1
410 Flex +Y
1 (HYD) 7904 -26953 -17132 0 0 0
2 (HYD) 7997 -26624 -16834 0 0 0
3 (HYD) 7665 -27423 -17599 0 0 0
4 (HYD) 7855 -26949 -17152 0 0 0
5 (HYD) 7882 -27109 -17262 0 0 0
MAX 7997/ 2 27423/ 3 17599/ 3 0/ 1 0/ 1 0/ 1
420 Flex +Y
1 (HYD) 7574 -26800 -17163 0 0 0
2 (HYD) 7667 -26446 -16850 0 0 0
3 (HYD) 7345 -27246 -17602 0 0 0
4 (HYD) 7534 -26772 -17159 0 0 0
5 (HYD) 7564 -26928 -17266 0 0 0
MAX 7667/ 2 27246/ 3 17602/ 3 0/ 1 0/ 1 0/ 1
35
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
430 Flex +Y
1 (HYD) 6946 -25132 -16163 0 0 0
2 (HYD) 7022 -24790 -15869 0 0 0
3 (HYD) 6758 -25539 -16551 0 0 0
4 (HYD) 6919 -25096 -16147 0 0 0
5 (HYD) 6943 -25238 -16245 0 0 0
MAX 7022/ 2 25539/ 3 16551/ 3 0/ 1 0/ 1 0/ 1
440 Flex +Y
1 (HYD) 5641 -20624 -13289 0 0 0
2 (HYD) 5678 -20344 -13060 0 0 0
3 (HYD) 5539 -20952 -13581 0 0 0
4 (HYD) 5627 -20593 -13271 0 0 0
5 (HYD) 5645 -20706 -13350 0 0 0
MAX 5678/ 2 20952/ 3 13581/ 3 0/ 1 0/ 1 0/ 1
450 Flex +Y
1 (HYD) 3312 -12134 -7822 0 0 0
2 (HYD) 3306 -11973 -7701 0 0 0
3 (HYD) 3301 -12323 -7970 0 0 0
4 (HYD) 3307 -12116 -7810 0 0 0
5 (HYD) 3319 -12181 -7854 0 0 0
MAX 3319/ 5 12323/ 3 7970/ 3 0/ 1 0/ 1 0/ 1
Displ.
800
Reaction
1 (HYD) 19473 -227297 -1005 0 0 0
2 (HYD) 36233 -220730 -658 0 0 0
3 (HYD) -1169 -228106 -465 0 0 0
4 (HYD) 18162 -221638 12761 0 0 0
5 (HYD) 19135 -225004 -14063 0 0 0
MAX 36233/ 2 228106/ 3 14063/ 5 0/ 1 0/ 1 0/ 1
Displ.
1000
Reaction
1 (HYD) -7729 -16540 1261 0 0 0
2 (HYD) -12336 -14374 1171 0 0 0
3 (HYD) -775 -20523 1491 0 0 0
4 (HYD) -7049 -17195 2587 0 0 0
5 (HYD) -8021 -16188 -128 0 0 0
36
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
Displ.
1500
Reaction
1 (HYD) -1372 -137 -7036 0 0 0
2 (HYD) 12157 1216 -7259 0 0 0
3 (HYD) -23918 -2392 -10934 0 0 0
4 (HYD) -5127 -513 9229 0 0 0
5 (HYD) -5734 -573 -26271 0 0 0
MAX 23918/ 3 2392/ 3 26271/ 5 0/ 1 0/ 1 0/ 1
Displ.
1800
Reaction
1 (HYD) -2929 -293 15534 0 0 0
2 (HYD) -1477 -148 14059 0 0 0
3 (HYD) 7884 788 21728 0 0 0
4 (HYD) -1391 -139 19344 0 0 0
5 (HYD) 2155 216 14917 0 0 0
MAX 7884/ 3 788/ 3 21728/ 3 0/ 1 0/ 1 0/ 1
Displ.
4600
Reaction
1 (HYD) -92579 -25727 216698 0 0 0
2 (HYD) -95668 -25341 225372 0 0 0
3 (HYD) -96182 -26190 223511 0 0 0
4 (HYD) -97084 -25689 227573 0 0 0
5 (HYD) -94064 -25839 220030 0 0 0
MAX 97084/ 4 26190/ 3 227573/ 4 0/ 1 0/ 1 0/ 1
37
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:25:40
Jobname: D:\SAKTHI\CAESAR\STD\24LINE\3 BEND CONFN\RISER24-HYD
Licensed To: B & W ID: 13709
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 10 221.42 448.15 49.4 20 221.42 448.15 49.4
2 (HYD) 10 221.42 448.15 49.4 20 221.42 448.15 49.4
3 (HYD) 10 221.42 448.15 49.4 20 221.42 448.15 49.4
4 (HYD) 10 221.42 448.15 49.4 20 221.42 448.15 49.4
5 (HYD) 10 221.42 448.15 49.4 20 221.42 448.15 49.4
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (HYD) 20 221.42 448.15 49.4 30 221.42 448.15 49.4
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 80 221.42 448.15 49.4 90 221.42 448.15 49.4
2 (HYD) 80 221.42 448.15 49.4 90 221.42 448.15 49.4
3 (HYD) 80 221.42 448.15 49.4 90 221.42 448.15 49.4
4 (HYD) 80 221.42 448.15 49.4 90 221.42 448.15 49.4
5 (HYD) 80 221.42 448.15 49.4 90 221.42 448.15 49.4
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 130 220.70 448.15 49.2 140 219.89 448.15 49.1
4 (HYD) 130 220.70 448.15 49.2 140 219.89 448.15 49.1
5 (HYD) 130 220.70 448.15 49.2 140 219.89 448.15 49.1
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (HYD) 180 216.85 448.15 48.4 190 214.97 448.15 48.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 240 0.00 0.00 0.0 250 0.00 0.00 0.0
2 (HYD) 240 0.00 0.00 0.0 250 0.00 0.00 0.0
3 (HYD) 240 0.00 0.00 0.0 250 0.00 0.00 0.0
4 (HYD) 240 0.00 0.00 0.0 250 0.00 0.00 0.0
5 (HYD) 240 0.00 0.00 0.0 250 0.00 0.00 0.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 280 214.42 448.15 47.8 290 213.52 448.15 47.6
4 (HYD) 280 215.03 448.15 48.0 290 213.77 448.15 47.7
5 (HYD) 280 215.45 448.15 48.1 290 213.93 448.15 47.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (HYD) 341 0.00 0.00 0.0 350 0.00 0.00 0.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 400 212.80 448.15 47.5 410 212.73 448.15 47.5
2 (HYD) 400 212.76 448.15 47.5 410 212.79 448.15 47.5
3 (HYD) 400 212.79 448.15 47.5 410 212.73 448.15 47.5
4 (HYD) 400 212.86 448.15 47.5 410 212.77 448.15 47.5
5 (HYD) 400 212.80 448.15 47.5 410 212.72 448.15 47.5
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 450 214.47 448.15 47.9 460 212.72 448.15 47.5
4 (HYD) 450 214.44 448.15 47.9 460 212.73 448.15 47.5
5 (HYD) 450 214.42 448.15 47.8 460 212.71 448.15 47.5
Cuu Long Joint Operating Company
Su Tu Field Development – Su Tu Den North East
Preliminary Engineering
Document No. : 2005-6031-2J-0010
Riser and Subsea Tie-in Spool Analysis Report
Revision: C
CAESAR II
LOAD CONDITION DESCRIPTION
RUN
OPERATION + 100 YEAR
OPERATION 1
ENVIRONMENTAL LOAD
HYDROTEST + 1 YEAR
HYDROTEST 2
ENVIRONMENTAL LOAD
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 47 of 49
1
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
Table of Contents
INPUT LISTING .................................................................................................................................................... 2
MISCELLANEOUS COMPUTED DATA ..................................................................................................................... 20
Displacements 1 (OPE) W+D5+T1+P1....................................................................................................... 28
Displacements 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1............................................................................ 30
Displacements 3 (OPE) W+D2+D5+T1+P1+WIN2+WAV2............................................................................ 32
Displacements 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3............................................................................ 34
Displacements 5 (OPE) W+D4+D5+T1+P1+WIN4+WAV4............................................................................ 36
Restraint Summary 1 (OPE) W+D5+T1+P1 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1 3 (OPE)
W+D2+D5+T1+P1+WIN2+WAV2 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3 5 (OPE)
W+D4+D5+T1+P1+WIN4+WAV4.............................................................................................................................. 38
Stresses 1 (OPE) W+D5+T1+P1................................................................................................................ 45
Stresses 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1..................................................................................... 50
Stresses 3 (OPE) W+D2+D5+T1+P1+WIN2+WAV2..................................................................................... 55
Stresses 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3..................................................................................... 60
Stresses 5 (OPE) W+D4+D5+T1+P1+WIN4+WAV4..................................................................................... 65
Code Compliance Extended 1 (OPE) W+D5+T1+P1 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1 3
(OPE) W+D2+D5+T1+P1+WIN2+WAV2 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3 5 (OPE)
W+D4+D5+T1+P1+WIN4+WAV4 70
2
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
Job Description:
ANALYST: SV
PIPE DATA
-----------------------------------------------------------------------------
-----------------------------------------------------------------------------
From 10 To 20 DX= 5,000.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= .750 mm. Cor= 3.0000 mm.
GENERAL
T1= 22 C P1= 128.9000 bars Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m. Insul= 1,440.0000 kg/cu.m.
Fluid= 185.0000000 kg/cu.m.
RESTRAINTS
Node 10 ANC Cnode 1000
DISPLACEMENTS
Node 1000 DX1= 33.800 mm. DY1= -28.500 mm. DZ1= 2.100 mm.
DX2= -167.800 mm. DY2= -33.000 mm. DZ2= -1.900 mm. DX3= -25.300 mm.
DY3= -29.300 mm. DZ3= 40.700 mm. DX4= -25.700 mm. DY4= -29.600 mm.
DZ4= -84.300 mm.
WIND
Wind Shape= .500
ALLOWABLE STRESSES
B31.8 VIII(2003) Sh1= 448 N./sq.mm. Sh2= 448 N./sq.mm.
Sh3= 448 N./sq.mm. Sh4= 448 N./sq.mm. Sh5= 448 N./sq.mm.
Sh6= 448 N./sq.mm. Sh7= 448 N./sq.mm. Sh8= 448 N./sq.mm.
Sh9= 448 N./sq.mm. Sy= 448 N./sq.mm. Fac= .5000
-----------------------------------------------------------------------------
From 20 To 30 DX= 3,500.000 mm.
BEND at "TO" end
Radius= 1,365.500 mm. (user) Bend Angle= 90.000
-----------------------------------------------------------------------------
From 30 To 40 DY= -4,500.000 mm.
BEND at "TO" end
Radius= 1,365.500 mm. (user) Bend Angle= 5.711
-----------------------------------------------------------------------------
From 40 To 50 DX= 230.700 mm. DY= -2,307.000 mm.
-----------------------------------------------------------------------------
From 50 To 60 DX= 19.300 mm. DY= -193.000 mm.
RIGID Weight= 1,196.51 N.
-----------------------------------------------------------------------------
From 60 To 70 DX= 19.300 mm. DY= -193.000 mm.
RIGID Weight= 1,196.51 N.
-----------------------------------------------------------------------------
From 70 To 80 DX= 130.700 mm. DY= -1,307.000 mm.
RESTRAINTS
Node 80 X Cnode 800 Dir Vec= .9950 .0995 .0000
Node 80 Z Cnode 800
3
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
DY3= -30.500 mm. DZ3= 36.000 mm. DX4= -29.800 mm. DY4= -31.200 mm.
DZ4= -73.700 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 148.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 150 To 160 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 144.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 160 To 170 DX= 230.000 mm. DY= -2,300.000 mm.
GENERAL
RESTRAINTS
Node 170 X Cnode 1700 Dir Vec= .9950 .0995 .0000
Node 170 Z Cnode 1700
DISPLACEMENTS
Node 1700 DX1= 17.300 mm. DY1= -31.200 mm. DZ1= .400 mm.
DX2= -128.500 mm. DY2= -31.200 mm. DZ2= .400 mm. DX3= -20.900 mm.
DY3= -30.500 mm. DZ3= 30.600 mm. DX4= -27.500 mm. DY4= -31.200 mm.
DZ4= -66.300 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 139.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 170 To 180 DX= 270.000 mm. DY= -2,700.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 139.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 180 To 190 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
RESTRAINTS
Node 190 X Cnode 1900 Dir Vec= .9950 .0995 .0000
Node 190 Z Cnode 1900
DISPLACEMENTS
Node 1900 DX1= 12.100 mm. DY1= -31.900 mm. DZ1= -.100 mm.
DX2= -113.100 mm. DY2= -29.700 mm. DZ2= -1.400 mm. DX3= -20.100 mm.
DY3= -30.500 mm. DZ3= 25.000 mm. DX4= -25.100 mm. DY4= -31.200 mm.
DZ4= -58.600 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 133.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 190 To 200 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 123.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 200 To 210 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
RESTRAINTS
5
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 330 To 340 DX= 4,602.500 mm. DZ= 1,953.700 mm.
GENERAL
RESTRAINTS
Node 340 +Y K= 310 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 340 To 341 DX= 3,682.000 mm. DZ= 1,562.900 mm.
GENERAL
RESTRAINTS
Node 341 +Y K= 248 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 341 To 350 DX= 1,380.800 mm. DZ= 586.100 mm.
GENERAL
RESTRAINTS
Node 350 +Y K= 93 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 350 To 360 DX= 3,221.800 mm. DZ= 1,367.600 mm.
PIPE
Dia= 273.100 mm. Wall= 12.870 mm. Insul= 35.750 mm.
GENERAL
BEND at "TO" end
Radius= 1,365.500 mm. (user) Bend Angle= 84.500
RESTRAINTS
Node 360 +Y K= 217 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 360 To 370 DX= -1,444.900 mm. DZ= 4,582.600 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= 35.750 mm.
GENERAL
RESTRAINTS
Node 370 +Y K= 310 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 370 To 371 DX= -1,503.500 mm. DZ= 4,768.600 mm.
GENERAL
RESTRAINTS
Node 371 +Y K= 310 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 371 To 380 DX= -58.600 mm. DZ= 186.000 mm.
GENERAL
RIGID Weight= 1,196.51 N.
WAVE
8
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 380 To 390 DX= -58.600 mm. DZ= 186.000 mm.
GENERAL
RIGID Weight= 1,196.51 N.
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 390 To 391 DX= -601.400 mm. DZ= 1,907.400 mm.
GENERAL
RESTRAINTS
Node 391 +Y K= 124 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 391 To 392 DX= -949.300 mm. DZ= 3,010.900 mm.
GENERAL
RESTRAINTS
Node 392 +Y K= 186 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 392 To 393 DX= -655.800 mm. DZ= 2,080.100 mm.
GENERAL
RESTRAINTS
Node 393 +Y K= 136 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 393 To 394 DX= -620.100 mm. DZ= 1,966.600 mm.
GENERAL
RESTRAINTS
Node 394 +Y K= 130 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
SIF's & TEE's
Node 394 Welding Tee
-----------------------------------------------------------------------------
From 394 To 511 DY= 847.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= .750 mm.
GENERAL
Insul= 1,440.0000 kg/cu.m.
BEND at "TO" end
Radius= 381.000 mm. (LONG) Bend Angle= 90.000
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 511 To 512 DX= 115.800 mm. DZ= -367.200 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 512 To 513 DX= 56.800 mm. DZ= -180.300 mm.
GENERAL
9
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 603 To 604 DX= 60.100 mm. DZ= -190.700 mm.
GENERAL
RIGID Weight= 1,196.50 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 394 To 395 DX= -842.000 mm. DZ= 2,670.400 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= 35.750 mm.
GENERAL
Insul= 3,014.2000 kg/cu.m.
RESTRAINTS
Node 395 +Y K= 186 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 395 To 396 DX= -60.100 mm. DZ= 190.700 mm.
GENERAL
RIGID Weight= 1,196.51 N.
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 396 To 397 DX= -60.100 mm. DZ= 190.700 mm.
GENERAL
RIGID Weight= 1,196.50 N.
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 397 To 400 DX= -1,503.500 mm. DZ= 4,768.600 mm.
GENERAL
RESTRAINTS
Node 400 +Y K= 310 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 400 To 410 DX= -1,503.500 mm. DZ= 4,768.600 mm.
GENERAL
RESTRAINTS
Node 410 +Y K= 310 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 410 To 460 DX= -1,503.500 mm. DZ= 4,768.600 mm.
RESTRAINTS
Node 460 ANC Cnode 4600
DISPLACEMENTS
Node 4600 DX5= 30.100 mm. DY5= .000 mm. DZ5= -95.400 mm.
MATERIAL Changes:
10 20 Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
11
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
BEND ELEMENTS
20 30 Radius= 1,365.500 mm. (user)
Bend Angle= 90.000
30 40 Radius= 1,365.500 mm. (user)
Bend Angle= 5.711
230 240 Radius= 1,365.500 mm. (user)
Bend Angle= 84.745
270 275 Radius= 1,365.000 mm. (user)
Bend Angle= 29.993
275 280 Radius= 1,365.500 mm. (user)
Bend Angle= 29.993
350 360 Radius= 1,365.500 mm. (user)
Bend Angle= 84.500
394 511 Radius= 381.000 mm. (LONG)
Bend Angle= 90.000
RIGIDS
50 60 RIGID Weight= 1,196.51 N.
60 70 RIGID Weight= 1,196.51 N.
250 260 RIGID Weight= 1,196.51 N.
260 270 RIGID Weight= 1,196.51 N.
371 380 RIGID Weight= 1,196.51 N.
380 390 RIGID Weight= 1,196.51 N.
512 513 RIGID Weight= 1,196.50 N.
513 514 RIGID Weight=11,631.50 N.
514 515 RIGID Weight= 1,196.50 N.
517 518 RIGID Weight= 1,196.50 N.
518 519 RIGID Weight=11,631.50 N.
519 601 RIGID Weight= 1,196.50 N.
603 604 RIGID Weight= 1,196.50 N.
395 396 RIGID Weight= 1,196.51 N.
396 397 RIGID Weight= 1,196.50 N.
RESTRAINTS Len MU
GAP YIELD Dir
12
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
DISPLACEMENTS
10 20 Node 1000 DX1= 33.800 mm. DY1= -28.500 mm.
DZ1= 2.100 mm. DX2= -167.800 mm.
DY2= -33.000 mm. DZ2= -1.900 mm.
DX3= -25.300 mm. DY3= -29.300 mm.
DZ3= 40.700 mm. DX4= -25.700 mm.
DY4= -29.600 mm. DZ4= -84.300 mm.
70 80 Node 800 DX1= 30.100 mm. DY1= -29.200 mm.
DZ1= 1.700 mm. DX2= -159.900 mm.
DY2= -32.900 mm. DZ2= -.600 mm.
DX3= -24.100 mm. DY3= -29.700 mm.
DZ3= 39.200 mm. DX4= -27.000 mm.
DY4= -30.100 mm. DZ4= -80.900 mm.
110 120 Node 1200 DX1= 26.700 mm. DY1= -29.800 mm.
DZ1= 1.300 mm. DX2= -152.500 mm.
13
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
WIND/WAVE
10 20 WIND Wind Shape= .500
90 100 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 74.000
Mar. Growth Dens.= 1,400.000
100 110 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 96.000
Mar. Growth Dens.= 1,400.000
110 120 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 119.000
Mar. Growth Dens.= 1,400.000
120 130 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 153.000
Mar. Growth Dens.= 1,400.000
130 140 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 153.000
Mar. Growth Dens.= 1,400.000
14
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
COORDINATE REPORT
/--------------------(mm.)----------------------/
NODE X Y Z
10 .0000 13500.0000 .0000
20 5000.0000 13500.0000 .0000
30 8500.0000 13500.0000 .0000
40 8500.0000 9000.0000 .0000
50 8730.7002 6693.0000 .0000
60 8750.0000 6500.0000 .0000
70 8769.2998 6307.0000 .0000
80 8900.0000 5000.0000 .0000
90 9400.0000 .0000 .0000
100 9500.0000 -1000.0000 .0000
110 9600.0000 -2000.0000 .0000
120 9690.0000 -2900.0000 .0000
130 9850.0000 -4500.0000 .0000
140 10350.0000 -9500.0000 .0000
150 10700.0000 -13000.0000 .0000
160 11200.0000 -18000.0000 .0000
170 11430.0000 -20300.0000 .0000
180 11700.0000 -23000.0000 .0000
190 12200.0000 -28000.0000 .0000
200 12700.0000 -33000.0000 .0000
210 13200.0000 -38000.0000 .0000
220 13340.0000 -39400.0000 .0000
230 13626.5000 -42265.0000 .0000
240 13831.2002 -44312.0000 .0000
19
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
BEND DATA:
TYPE KEY:
3 - Welding Tee
4 - Sweepolet
5 - Weldolet
10. 20. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
20. 30. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
30. 40. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
40. 50. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
50. 60. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
60. 70. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
70. 80. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
80. 90. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
90. 100. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
100. 110. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
110. 120. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
120. 130. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
130. 140. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
140. 150. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
150. 160. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
160. 170. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
170. 180. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
180. 190. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
190. 200. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
200. 210. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
210. 220. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
220. 230. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
230. 240. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
240. 250. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
250. 260. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
260. 270. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
270. 275. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
275. 280. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
280. 290. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
290. 300. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
300. 310. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
310. 320. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
320. 330. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
330. 340. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
340. 341. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
341. 350. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
350. 360. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
360. 370. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
370. 371. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
371. 380. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
23
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
380. 390. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
390. 391. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
391. 392. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
392. 393. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
393. 394. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
394. 511. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
511. 512. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
512. 513. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
513. 514. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
514. 515. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
515. 516. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
516. 517. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
517. 518. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
518. 519. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
519. 601. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
601. 602. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
602. 603. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
603. 604. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
394. 395. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
395. 396. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
396. 397. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
397. 400. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
400. 410. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
410. 460. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
WIND LOADING #: 1
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... 1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 2
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... -1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 3
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... 1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
25
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
WIND LOADING #: 4
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... -1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WAVE VECTOR 1
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and 1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1400.000
2 22800.000 1200.000
3 45600.000 700.000
4 0.000 0.000
26
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 2
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and -1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: -1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1400.000
2 22800.000 1200.000
3 45600.000 700.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 3
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and 0.000 1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
27
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
WAVE VECTOR 4
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and 0.000 -1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 0.000 -1.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1400.000
2 22800.000 1200.000
3 45600.000 700.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
28
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
Rigid X;
80 Rigid Z;
Rigid +Y
1 (OPE) 6186 -65411 -6 0 0 0
2 (OPE) 6192 -60704 107 0 0 0
3 (OPE) 6022 -70321 -210 0 0 0
4 (OPE) 6138 -66068 1772 0 0 0
5 (OPE) 6263 -65152 -7026 0 0 0
MAX 6263/ 5 70321/ 3 7026/ 5 0/ 1 0/ 1 0/ 1
Rigid X;
120
Rigid Z
1 (OPE) -1015 -101 10 0 0 0
2 (OPE) 32990 3299 -26 0 0 0
3 (OPE) -36573 -3657 347 0 0 0
4 (OPE) -1619 -162 33844 0 0 0
5 (OPE) -1619 -162 -30275 0 0 0
MAX 36573/ 3 3657/ 3 33844/ 4 0/ 1 0/ 1 0/ 1
Rigid X;
150
Rigid Z
1 (OPE) -974 -97 -38 0 0 0
2 (OPE) 30654 3065 142 0 0 0
3 (OPE) -33193 -3319 -865 0 0 0
4 (OPE) -1519 -152 34489 0 0 0
5 (OPE) -2277 -228 -34482 0 0 0
MAX 33193/ 3 3319/ 3 34489/ 4 0/ 1 0/ 1 0/ 1
Rigid X;
170
Rigid Z
1 (OPE) -390 -39 148 0 0 0
2 (OPE) 19094 1909 -402 0 0 0
3 (OPE) -19760 -1976 1801 0 0 0
39
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
Rigid X;
190
Rigid Z
1 (OPE) -1505 -151 -422 0 0 0
2 (OPE) 18300 1830 1301 0 0 0
3 (OPE) -25108 -2511 -4492 0 0 0
4 (OPE) -329 -33 14309 0 0 0
5 (OPE) -16278 -1628 -5168 0 0 0
MAX 25108/ 3 2511/ 3 14309/ 4 0/ 1 0/ 1 0/ 1
Rigid X;
210
Rigid Z
1 (OPE) 2551 255 1683 0 0 0
2 (OPE) 14978 1498 -2444 0 0 0
3 (OPE) -3754 -375 9886 0 0 0
4 (OPE) 468 47 29581 0 0 0
5 (OPE) 25868 2587 -41064 0 0 0
MAX 25868/ 5 2587/ 5 41064/ 5 0/ 1 0/ 1 0/ 1
290 Flex +Y
1 (OPE) -1678 -2423 -248 0 0 0
2 (OPE) 1612 -4425 -2645 0 0 0
3 (OPE) -1092 -1651 380 0 0 0
4 (OPE) -1650 -5878 3769 0 0 0
5 (OPE) 0 0 0 0 0 0
MAX 1678/ 1 5878/ 4 3769/ 4 0/ 1 0/ 1 0/ 1
300 Flex +Y
1 (OPE) -3230 -5437 -2014 0 0 0
2 (OPE) 3823 -5759 1279 0 0 0
3 (OPE) -3352 -4826 420 0 0 0
4 (OPE) -3253 -11121 7073 0 0 0
5 (OPE) 0 0 0 0 0 0
MAX 3823/ 2 11121/ 4 7073/ 4 0/ 1 0/ 1 0/ 1
310 Flex +Y
1 (OPE) -3565 -5204 -748 0 0 0
2 (OPE) 2803 -4104 630 0 0 0
3 (OPE) -3987 -5700 -164 0 0 0
4 (OPE) -6349 -10379 3531 0 0 0
5 (OPE) 0 0 0 0 0 0
MAX 6349/ 4 10379/ 4 3531/ 4 0/ 1 0/ 1 0/ 1
320 Flex +Y
1 (OPE) -1521 -4943 3108 0 0 0
2 (OPE) 1316 -3812 2321 0 0 0
40
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
330 Flex +Y
1 (OPE) 1287 -4764 -3076 0 0 0
2 (OPE) 2774 -3993 345 0 0 0
3 (OPE) -3489 -5558 -1722 0 0 0
4 (OPE) -2909 -9675 6116 0 0 0
5 (OPE) 0 0 0 0 0 0
MAX 3489/ 3 9675/ 4 6116/ 4 0/ 1 0/ 1 0/ 1
340 Flex +Y
1 (OPE) 1263 -4605 -2966 0 0 0
2 (OPE) 1167 -3867 -2443 0 0 0
3 (OPE) -1962 -5509 -3320 0 0 0
4 (OPE) -764 -9390 -6529 0 0 0
5 (OPE) 0 0 0 0 0 0
MAX 1962/ 3 9390/ 4 6529/ 4 0/ 1 0/ 1 0/ 1
341 Flex +Y
1 (OPE) 1009 -3680 -2370 0 0 0
2 (OPE) 695 -2454 -1570 0 0 0
3 (OPE) -549 -5019 -3470 0 0 0
4 (OPE) 2043 -7599 -4911 0 0 0
5 (OPE) 0 0 0 0 0 0
MAX 2043/ 4 7599/ 4 4911/ 4 0/ 1 0/ 1 0/ 1
350 Flex +Y
1 (OPE) 382 -1392 -897 0 0 0
2 (OPE) 212 -753 -483 0 0 0
3 (OPE) -103 -2052 -1432 0 0 0
4 (OPE) 781 -2887 -1864 0 0 0
5 (OPE) 0 0 0 0 0 0
MAX 781/ 4 2887/ 4 1864/ 4 0/ 1 0/ 1 0/ 1
360 Flex +Y
1 (OPE) 1021 -3221 -2010 0 0 0
2 (OPE) 137 -357 -209 0 0 0
3 (OPE) 341 -5890 -4109 0 0 0
4 (OPE) 2008 -5818 -3543 0 0 0
5 (OPE) 0 0 0 0 0 0
MAX 2008/ 4 5890/ 3 4109/ 3 0/ 1 0/ 1 0/ 1
370 Flex +Y
1 (OPE) 1775 -4890 -2927 0 0 0
2 (OPE) 459 -783 -299 0 0 0
3 (OPE) 613 -8914 -6210 0 0 0
41
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
371 Flex +Y
1 (OPE) 2195 -6536 -4015 0 0 0
2 (OPE) 1456 -2174 -444 0 0 0
3 (OPE) 59 -10989 -7692 0 0 0
4 (OPE) 2481 -5906 -3307 0 0 0
5 (OPE) -1915 -7528 -4910 0 0 0
MAX 2481/ 4 10989/ 3 7692/ 3 0/ 1 0/ 1 0/ 1
391 Flex +Y
1 (OPE) 969 -3153 -1983 0 0 0
2 (OPE) 917 -1346 -215 0 0 0
3 (OPE) -145 -5014 -3507 0 0 0
4 (OPE) 1105 -2830 -1644 0 0 0
5 (OPE) -787 -3695 -2464 0 0 0
MAX 1105/ 4 5014/ 3 3507/ 3 0/ 1 0/ 1 0/ 1
392 Flex +Y
1 (OPE) 1643 -6137 -3969 0 0 0
2 (OPE) 2312 -3355 -414 0 0 0
3 (OPE) -610 -8996 -6268 0 0 0
4 (OPE) 1950 -5678 -3464 0 0 0
5 (OPE) -795 -6862 -4737 0 0 0
MAX 2312/ 2 8996/ 3 6268/ 3 0/ 1 0/ 1 0/ 1
393 Flex +Y
1 (OPE) 1279 -5239 -3437 0 0 0
2 (OPE) 2135 -3086 -330 0 0 0
3 (OPE) -673 -7418 -5149 0 0 0
4 (OPE) 1546 -4938 -3092 0 0 0
5 (OPE) -212 -5669 -3963 0 0 0
MAX 2135/ 2 7418/ 3 5149/ 3 0/ 1 0/ 1 0/ 1
394 Flex +Y
1 (OPE) 1235 -5428 -3593 0 0 0
2 (OPE) 2159 -3114 -297 0 0 0
3 (OPE) -852 -7702 -5324 0 0 0
4 (OPE) 1502 -5154 -3280 0 0 0
5 (OPE) 159 -5770 -4036 0 0 0
MAX 2159/ 2 7702/ 3 5324/ 3 0/ 1 0/ 1 0/ 1
395 Flex +Y
1 (OPE) 1582 -7419 -4947 0 0 0
2 (OPE) 2506 -3609 -321 0 0 0
3 (OPE) -1429 -11084 -7626 0 0 0
4 (OPE) 1912 -7025 -4530 0 0 0
42
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
400 Flex +Y
1 (OPE) 1673 -8299 -5563 0 0 0
2 (OPE) 1504 -2183 -271 0 0 0
3 (OPE) -1608 -14236 -9835 0 0 0
4 (OPE) 1920 -7720 -5052 0 0 0
5 (OPE) 1487 -8850 -6013 0 0 0
MAX 1920/ 4 14236/ 3 9835/ 3 0/ 1 0/ 1 0/ 1
410 Flex +Y
1 (OPE) 875 -4302 -2881 0 0 0
2 (OPE) 279 -436 -123 0 0 0
3 (OPE) -50 -8108 -5675 0 0 0
4 (OPE) 913 -3939 -2601 0 0 0
5 (OPE) 911 -4647 -3123 0 0 0
MAX 913/ 4 8108/ 3 5675/ 3 0/ 1 0/ 1 0/ 1
516 Flex +Y
1 (OPE) 1406 -6010 -3965 0 0 0
2 (OPE) 3030 -4400 -555 0 0 0
3 (OPE) -597 -7680 -5343 0 0 0
4 (OPE) 1716 -5793 -3675 0 0 0
5 (OPE) 367 -6322 -4410 0 0 0
MAX 3030/ 2 7680/ 3 5343/ 3 0/ 1 0/ 1 0/ 1
602 Flex +Y
1 (OPE) 2128 -8708 -5713 0 0 0
2 (OPE) 5302 -7756 -1166 0 0 0
3 (OPE) -450 -9881 -6902 0 0 0
4 (OPE) 2608 -8528 -5370 0 0 0
5 (OPE) 155 -9046 -6331 0 0 0
MAX 5302/ 2 9881/ 3 6902/ 3 0/ 1 0/ 1 0/ 1
Displ.
800
Reaction
1 (OPE) 6186 -65411 -6 0 0 0
2 (OPE) 6192 -60704 107 0 0 0
3 (OPE) 6022 -70320 -210 0 0 0
4 (OPE) 6138 -66068 1772 0 0 0
43
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
Displ.
1000
Reaction
1 (OPE) -1187 -3179 2 0 0 0
2 (OPE) -666 -3112 -46 0 0 0
3 (OPE) -1427 -3482 61 0 0 0
4 (OPE) -1080 -3260 744 0 0 0
5 (OPE) -1249 -3135 1412 0 0 0
MAX 1427/ 3 3482/ 3 1412/ 5 0/ 1 0/ 1 0/ 1
Displ.
1200
Reaction
1 (OPE) -1015 -101 10 0 0 0
2 (OPE) 32990 3299 -26 0 0 0
3 (OPE) -36573 -3657 347 0 0 0
4 (OPE) -1619 -162 33844 0 0 0
5 (OPE) -1619 -162 -30275 0 0 0
MAX 36573/ 3 3657/ 3 33844/ 4 0/ 1 0/ 1 0/ 1
Displ.
1500
Reaction
1 (OPE) -974 -97 -38 0 0 0
2 (OPE) 30654 3065 142 0 0 0
3 (OPE) -33193 -3319 -865 0 0 0
4 (OPE) -1519 -152 34489 0 0 0
5 (OPE) -2277 -228 -34482 0 0 0
MAX 33193/ 3 3319/ 3 34489/ 4 0/ 1 0/ 1 0/ 1
Displ.
1700
Reaction
1 (OPE) -390 -39 148 0 0 0
2 (OPE) 19094 1909 -402 0 0 0
3 (OPE) -19760 -1976 1801 0 0 0
4 (OPE) -1157 -116 20328 0 0 0
5 (OPE) 4143 414 -23272 0 0 0
MAX 19760/ 3 1976/ 3 23272/ 5 0/ 1 0/ 1 0/ 1
Displ.
1900
Reaction
1 (OPE) -1505 -151 -422 0 0 0
2 (OPE) 18300 1830 1301 0 0 0
3 (OPE) -25108 -2511 -4492 0 0 0
4 (OPE) -329 -33 14309 0 0 0
5 (OPE) -16278 -1628 -5168 0 0 0
MAX 25108/ 3 2511/ 3 14309/ 4 0/ 1 0/ 1 0/ 1
2100 Displ.
44
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
Displ.
4600
Reaction
1 (OPE) -16615 -2269 52334 0 0 0
2 (OPE) 3964 2037 13731 0 0 0
3 (OPE) -26457 -6624 69451 0 0 0
4 (OPE) -18829 -1849 60794 0 0 0
5 (OPE) -6308 -2700 20169 0 0 0
MAX 26457/ 3 6624/ 3 69451/ 3 0/ 1 0/ 1 0/ 1
45
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:22: 0
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-OP-L
Licensed To: B & W ID: 13709
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 10 138.59 224.07 61.9 20 138.59 224.07 61.9
2 (OPE) 10 138.59 224.07 61.9 20 138.59 224.07 61.9
3 (OPE) 10 138.59 224.07 61.9 20 138.59 224.07 61.9
4 (OPE) 10 138.59 224.07 61.9 20 138.59 224.07 61.9
5 (OPE) 10 138.59 224.07 61.9 20 138.59 224.07 61.9
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (OPE) 20 138.59 224.07 61.9 30 138.59 224.07 61.9
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 80 138.59 224.07 61.9 90 138.59 224.07 61.9
2 (OPE) 80 138.59 224.07 61.9 90 138.59 224.07 61.9
3 (OPE) 80 138.59 224.07 61.9 90 138.59 224.07 61.9
4 (OPE) 80 138.59 224.07 61.9 90 138.59 224.07 61.9
5 (OPE) 80 138.59 224.07 61.9 90 138.59 224.07 61.9
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 130 138.11 224.07 61.6 140 137.57 224.07 61.4
4 (OPE) 130 138.11 224.07 61.6 140 137.57 224.07 61.4
5 (OPE) 130 138.11 224.07 61.6 140 137.57 224.07 61.4
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (OPE) 180 136.11 224.07 60.7 190 135.57 224.07 60.5
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 240 133.80 224.07 59.7 250 133.80 224.07 59.7
2 (OPE) 240 133.80 224.07 59.7 250 133.80 224.07 59.7
3 (OPE) 240 133.80 224.07 59.7 250 133.80 224.07 59.7
4 (OPE) 240 133.80 224.07 59.7 250 133.80 224.07 59.7
5 (OPE) 240 133.80 224.07 59.7 250 133.80 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 280 133.68 224.07 59.7 290 133.68 224.07 59.7
4 (OPE) 280 133.68 224.07 59.7 290 133.68 224.07 59.7
5 (OPE) 280 133.68 224.07 59.7 290 268.21 403.33 66.5
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (OPE) 330 250.59 403.33 62.1 340 133.68 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 371 0.00 0.00 0.0 380 0.00 0.00 0.0
2 (OPE) 371 0.00 0.00 0.0 380 0.00 0.00 0.0
3 (OPE) 371 0.00 0.00 0.0 380 0.00 0.00 0.0
4 (OPE) 371 0.00 0.00 0.0 380 0.00 0.00 0.0
5 (OPE) 371 0.00 0.00 0.0 380 0.00 0.00 0.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 393 133.68 224.07 59.7 394 133.68 224.07 59.7
4 (OPE) 393 133.68 224.07 59.7 394 133.68 224.07 59.7
5 (OPE) 393 133.68 224.07 59.7 394 133.68 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (OPE) 514 0.00 0.00 0.0 515 0.00 0.00 0.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 601 133.77 224.07 59.7 602 133.77 224.07 59.7
2 (OPE) 601 133.77 224.07 59.7 602 133.77 224.07 59.7
3 (OPE) 601 133.77 224.07 59.7 602 133.77 224.07 59.7
4 (OPE) 601 133.77 224.07 59.7 602 133.77 224.07 59.7
5 (OPE) 601 133.77 224.07 59.7 602 133.77 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 396 0.00 0.00 0.0 397 0.00 0.00 0.0
4 (OPE) 396 0.00 0.00 0.0 397 0.00 0.00 0.0
5 (OPE) 396 0.00 0.00 0.0 397 0.00 0.00 0.0
Table of Contents
INPUT LISTING .................................................................................................................................................... 2
MISCELLANEOUS COMPUTED DATA ..................................................................................................................... 19
Displacements 1 (HYD) W+D5+T1+HP....................................................................................................... 27
Displacements 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1............................................................................ 29
Displacements 3 (HYD) W+D2+D5+T1+HP+WIN2+WAV2............................................................................ 31
Displacements 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3............................................................................ 33
Displacements 5 (HYD) W+D4+D5+T1+HP+WIN4+WAV4............................................................................ 35
Restraint Summary 1 (HYD) W+D5+T1+HP 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1 3 (HYD)
W+D2+D5+T1+HP+WIN2+WAV2 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3 5 (HYD)
W+D4+D5+T1+HP+WIN4+WAV4.............................................................................................................................. 37
Stresses 1 (HYD) W+D5+T1+HP................................................................................................................ 44
Stresses 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1..................................................................................... 49
Stresses 3 (HYD) W+D2+D5+T1+HP+WIN2+WAV2..................................................................................... 54
Stresses 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3..................................................................................... 59
Stresses 5 (HYD) W+D4+D5+T1+HP+WIN4+WAV4..................................................................................... 64
Code Compliance Extended 1 (HYD) W+D5+T1+HP 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1 3
(HYD) W+D2+D5+T1+HP+WIN2+WAV2 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3 5 (HYD)
W+D4+D5+T1+HP+WIN4+WAV4 69
2
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
INPUT LISTING
Job Description:
ANALYST: SV
PIPE DATA
-----------------------------------------------------------------------------
-----------------------------------------------------------------------------
From 10 To 20 DX= 5,000.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= .750 mm.
GENERAL
T1= 29 C PHyd= 219.4500 bars Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m. Insul= 1,440.0000 kg/cu.m.
Fluid=1025.0000000 kg/cu.m.
RESTRAINTS
Node 10 ANC Cnode 1000
DISPLACEMENTS
Node 1000 DX1= 9.900 mm. DY1= -31.100 mm. DZ1= 1.900 mm.
DX2= -110.700 mm. DY2= -33.400 mm. DZ2= -.500 mm. DX3= -26.100 mm.
DY3= -31.300 mm. DZ3= 25.700 mm. DX4= -25.900 mm. DY4= -31.900 mm.
DZ4= -45.000 mm.
WIND
Wind Shape= .500
ALLOWABLE STRESSES
B31.8 VIII(2003) Sh1= 448 N./sq.mm. Sh2= 448 N./sq.mm.
Sh3= 448 N./sq.mm. Sh4= 448 N./sq.mm. Sh5= 448 N./sq.mm.
Sh6= 448 N./sq.mm. Sh7= 448 N./sq.mm. Sh8= 448 N./sq.mm.
Sh9= 448 N./sq.mm. Sy= 448 N./sq.mm. Fac= .5000
-----------------------------------------------------------------------------
From 20 To 30 DX= 3,500.000 mm.
BEND at "TO" end
Radius= 1,365.500 mm. (user) Bend Angle= 90.000
-----------------------------------------------------------------------------
From 30 To 40 DY= -4,500.000 mm.
BEND at "TO" end
Radius= 1,365.500 mm. (user) Bend Angle= 5.711
-----------------------------------------------------------------------------
From 40 To 50 DX= 230.700 mm. DY= -2,307.000 mm.
-----------------------------------------------------------------------------
From 50 To 60 DX= 19.300 mm. DY= -193.000 mm.
RIGID Weight= 1,196.51 N.
-----------------------------------------------------------------------------
From 60 To 70 DX= 19.300 mm. DY= -193.000 mm.
RIGID Weight= 1,196.51 N.
-----------------------------------------------------------------------------
From 70 To 80 DX= 130.700 mm. DY= -1,307.000 mm.
RESTRAINTS
Node 80 X Cnode 800 Dir Vec= .9950 .0995 .0000
Node 80 Z Cnode 800
3
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 220 To 230 DX= 286.500 mm. DY= -2,865.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 230 To 240 DX= 204.700 mm. DY= -2,047.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.870 mm. Insul= .750 mm.
GENERAL
BEND at "TO" end
Radius= 1,365.500 mm. (user) Bend Angle= 84.745
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 240 To 250 DX= 2,065.600 mm. DZ= 876.800 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= .750 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 250 To 260 DX= 178.600 mm. DZ= 75.800 mm.
GENERAL
RIGID Weight= 1,196.51 N.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 260 To 270 DX= 178.600 mm. DZ= 75.800 mm.
GENERAL
RIGID Weight= 1,196.51 N.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 270 To 275 DX= 1,289.600 mm. DZ= 547.400 mm.
PIPE
Dia= 273.100 mm. Wall= 12.870 mm. Insul= .750 mm.
GENERAL
BEND at "TO" end
Radius= 1,365.000 mm. (user) Bend Angle= 29.993
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 275 To 280 DX= 1,779.300 mm. DY= -1,115.700 mm. DZ= 755.300 mm.
PIPE
Dia= 273.100 mm. Wall= 12.870 mm. Insul= .750 mm.
GENERAL
BEND at "TO" end
Radius= 1,365.500 mm. (user) Bend Angle= 29.993
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
6
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 392 To 393 DX= -655.800 mm. DZ= 2,080.100 mm.
GENERAL
RESTRAINTS
Node 393 +Y K= 136 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 393 To 394 DX= -620.100 mm. DZ= 1,966.600 mm.
GENERAL
RESTRAINTS
Node 394 +Y K= 130 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
SIF's & TEE's
Node 394 Welding Tee
-----------------------------------------------------------------------------
From 394 To 511 DY= 847.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= .750 mm.
GENERAL
Insul= 1,440.0000 kg/cu.m.
BEND at "TO" end
Radius= 381.000 mm. (LONG) Bend Angle= 90.000
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 511 To 512 DX= 115.800 mm. DZ= -367.200 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 512 To 513 DX= 56.800 mm. DZ= -180.300 mm.
GENERAL
RIGID Weight= 1,196.50 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 513 To 514 DX= 252.000 mm. DZ= -799.200 mm.
GENERAL
RIGID Weight=11,631.50 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 514 To 515 DX= 60.100 mm. DZ= -190.700 mm.
GENERAL
RIGID Weight= 1,196.50 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 515 To 516 DX= 135.300 mm. DZ= -429.200 mm.
GENERAL
RESTRAINTS
Node 516 +Y K= 136 N./mm. Mu = .70
9
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
INPUT LISTING
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 516 To 517 DX= 135.300 mm. DZ= -429.200 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 517 To 518 DX= 60.100 mm. DZ= -190.700 mm.
GENERAL
RIGID Weight= 1,196.50 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 518 To 519 DX= 252.000 mm. DZ= -799.200 mm.
GENERAL
RIGID Weight=11,631.50 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 519 To 601 DX= 60.100 mm. DZ= -190.700 mm.
GENERAL
RIGID Weight= 1,196.50 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 601 To 602 DX= 148.200 mm. DZ= -470.200 mm.
GENERAL
RESTRAINTS
Node 602 +Y K= 186 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 602 To 603 DX= 147.300 mm. DZ= -467.300 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 603 To 604 DX= 60.100 mm. DZ= -190.700 mm.
GENERAL
RIGID Weight= 1,196.50 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 394 To 395 DX= -842.000 mm. DZ= 2,670.400 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= 35.750 mm.
GENERAL
Insul= 3,014.2000 kg/cu.m.
RESTRAINTS
Node 395 +Y K= 186 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 395 To 396 DX= -60.100 mm. DZ= 190.700 mm.
10
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
INPUT LISTING
GENERAL
RIGID Weight= 1,196.51 N.
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 396 To 397 DX= -60.100 mm. DZ= 190.700 mm.
GENERAL
RIGID Weight= 1,196.50 N.
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 397 To 400 DX= -1,503.500 mm. DZ= 4,768.600 mm.
GENERAL
RESTRAINTS
Node 400 +Y K= 310 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 400 To 410 DX= -1,503.500 mm. DZ= 4,768.600 mm.
GENERAL
RESTRAINTS
Node 410 +Y K= 310 N./mm. Mu = .70
WAVE
Drag Coef= .650 Added Mass Coef= 2.100 Lift Coef= .850
-----------------------------------------------------------------------------
From 410 To 460 DX= -1,503.500 mm. DZ= 4,768.600 mm.
RESTRAINTS
Node 460 ANC Cnode 4600
DISPLACEMENTS
Node 4600 DX5= 31.000 mm. DY5= .000 mm. DZ5= -98.200 mm.
MATERIAL Changes:
10 20 Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m.
JOBNAME: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
BEND ELEMENTS
20 30 Radius= 1,365.500 mm. (user)
Bend Angle= 90.000
30 40 Radius= 1,365.500 mm. (user)
Bend Angle= 5.711
230 240 Radius= 1,365.500 mm. (user)
Bend Angle= 84.745
11
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
INPUT LISTING
RIGIDS
50 60 RIGID Weight= 1,196.51 N.
60 70 RIGID Weight= 1,196.51 N.
250 260 RIGID Weight= 1,196.51 N.
260 270 RIGID Weight= 1,196.51 N.
371 380 RIGID Weight= 1,196.51 N.
380 390 RIGID Weight= 1,196.51 N.
512 513 RIGID Weight= 1,196.50 N.
513 514 RIGID Weight=11,631.50 N.
514 515 RIGID Weight= 1,196.50 N.
517 518 RIGID Weight= 1,196.50 N.
518 519 RIGID Weight=11,631.50 N.
519 601 RIGID Weight= 1,196.50 N.
603 604 RIGID Weight= 1,196.50 N.
395 396 RIGID Weight= 1,196.51 N.
396 397 RIGID Weight= 1,196.50 N.
RESTRAINTS Len MU
GAP YIELD Dir
NODE TYPE CNODE STIF1 STIF2 FORCE Vectors
-------+-------+------+----------+----------+----------+---------------------
10 ANC 1000 .000 .000 .000
80 X 800 .995 .100 .000
80 Z 800 .000 .000 1.000
80 +Y 800 .000 1.000 .000
120 X 1200 .995 .100 .000
120 Z 1200 .000 .000 1.000
150 X 1500 .995 .100 .000
150 Z 1500 .000 .000 1.000
170 X 1700 .995 .100 .000
170 Z 1700 .000 .000 1.000
190 X 1900 .995 .100 .000
190 Z 1900 .000 .000 1.000
210 X 2100 .995 .100 .000
210 Z 2100 .000 .000 1.000
290 +Y 155 .70 .000 1.000 .000
300 +Y 310 .70 .000 1.000 .000
310 +Y 310 .70 .000 1.000 .000
320 +Y 310 .70 .000 1.000 .000
12
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
INPUT LISTING
DISPLACEMENTS
10 20 Node 1000 DX1= 9.900 mm. DY1= -31.100 mm.
DZ1= 1.900 mm. DX2= -110.700 mm.
DY2= -33.400 mm. DZ2= -.500 mm.
DX3= -26.100 mm. DY3= -31.300 mm.
DZ3= 25.700 mm. DX4= -25.900 mm.
DY4= -31.900 mm. DZ4= -45.000 mm.
70 80 Node 800 DX1= 7.600 mm. DY1= -31.700 mm.
DZ1= 1.700 mm. DX2= -105.200 mm.
DY2= -33.500 mm. DZ2= .300 mm.
DX3= -25.200 mm. DY3= -31.700 mm.
DZ3= 24.700 mm. DX4= -26.500 mm.
DY4= -32.300 mm. DZ4= -42.900 mm.
110 120 Node 1200 DX1= 5.500 mm. DY1= -32.300 mm.
DZ1= 1.500 mm. DX2= -100.100 mm.
DY2= -33.600 mm. DZ2= 1.000 mm.
DX3= -24.400 mm. DY3= -32.100 mm.
DZ3= 23.800 mm. DX4= -27.000 mm.
DY4= -32.700 mm. DZ4= -41.000 mm.
140 150 Node 1500 DX1= 2.700 mm. DY1= -33.000 mm.
DZ1= 1.300 mm. DX2= -93.600 mm.
DY2= -33.700 mm. DZ2= 2.000 mm.
DX3= -23.300 mm. DY3= -32.600 mm.
DZ3= 22.600 mm. DX4= -27.700 mm.
DY4= -33.200 mm. DZ4= -38.500 mm.
160 170 Node 1700 DX1= .200 mm. DY1= -33.200 mm.
DZ1= .500 mm. DX2= -83.400 mm.
DY2= -32.800 mm. DZ2= .500 mm.
DX3= -22.400 mm. DY3= -32.600 mm.
DZ3= 18.700 mm. DX4= -25.800 mm.
DY4= -33.200 mm. DZ4= -34.400 mm.
180 190 Node 1900 DX1= -2.500 mm. DY1= -33.500 mm.
DZ1= -.300 mm. DX2= -72.700 mm.
DY2= -31.900 mm. DZ2= -1.100 mm.
DX3= -21.400 mm. DY3= -32.700 mm.
13
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
INPUT LISTING
WIND/WAVE
10 20 WIND Wind Shape= .500
90 100 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
100 110 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
110 120 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
120 130 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
130 140 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
140 150 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
150 160 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
160 170 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
170 180 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
180 190 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
190 200 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
200 210 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
210 220 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
220 230 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
230 240 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
240 250 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
250 260 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
260 270 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
270 275 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
275 280 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
14
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
COORDINATE REPORT
/--------------------(mm.)----------------------/
NODE X Y Z
10 .0000 13500.0000 .0000
20 5000.0000 13500.0000 .0000
30 8500.0000 13500.0000 .0000
40 8500.0000 9000.0000 .0000
50 8730.7002 6693.0000 .0000
60 8750.0000 6500.0000 .0000
70 8769.2998 6307.0000 .0000
80 8900.0000 5000.0000 .0000
90 9400.0000 .0000 .0000
100 9500.0000 -1000.0000 .0000
110 9600.0000 -2000.0000 .0000
120 9690.0000 -2900.0000 .0000
130 9850.0000 -4500.0000 .0000
140 10350.0000 -9500.0000 .0000
150 10700.0000 -13000.0000 .0000
160 11200.0000 -18000.0000 .0000
170 11430.0000 -20300.0000 .0000
180 11700.0000 -23000.0000 .0000
190 12200.0000 -28000.0000 .0000
200 12700.0000 -33000.0000 .0000
210 13200.0000 -38000.0000 .0000
220 13340.0000 -39400.0000 .0000
230 13626.5000 -42265.0000 .0000
240 13831.2002 -44312.0000 .0000
250 15896.8008 -44312.0000 876.8000
260 16075.4004 -44312.0000 952.6000
270 16254.0000 -44312.0000 1028.4000
275 17543.5996 -44312.0000 1575.8000
280 19322.9004 -45427.6992 2331.1001
18
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
INPUT LISTING
BEND DATA:
TYPE KEY:
3 - Welding Tee
4 - Sweepolet
5 - Weldolet
10. 20. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
20
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
20. 30. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
30. 40. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
40. 50. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
50. 60. 6.169 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
60. 70. 6.169 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
70. 80. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
80. 90. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
90. 100. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
100. 110. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
110. 120. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
120. 130. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
130. 140. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
140. 150. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
150. 160. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
160. 170. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
170. 180. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
180. 190. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
190. 200. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
200. 210. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
210. 220. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
220. 230. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
230. 240. 0.810 0.009 0.483 0.000E+00 0.000E+00 0.000E+00 .000 .000
240. 250. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
250. 260. 6.167 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
260. 270. 6.167 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
270. 275. 0.810 0.009 0.483 0.000E+00 0.000E+00 0.000E+00 .000 .000
275. 280. 0.810 0.009 0.483 0.000E+00 0.000E+00 0.000E+00 .000 .000
280. 290. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
290. 300. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
300. 310. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
310. 320. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
320. 330. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
330. 340. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
340. 341. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
341. 350. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
350. 360. 0.810 1.025 0.483 0.000E+00 0.000E+00 0.000E+00 .000 .000
360. 370. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
370. 371. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
371. 380. 6.136 1.794 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
380. 390. 6.136 1.794 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
390. 391. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
391. 392. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
392. 393. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
393. 394. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
394. 511. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
511. 512. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
512. 513. 6.330 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
513. 514. 13.880 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
514. 515. 5.984 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
515. 516. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
516. 517. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
517. 518. 5.984 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
518. 519. 13.880 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
519. 601. 5.984 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
601. 602. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
21
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
602. 603. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
603. 604. 5.984 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
394. 395. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
395. 396. 5.984 1.794 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
396. 397. 5.984 1.794 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
397. 400. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
400. 410. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
410. 460. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
10. 20. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
20. 30. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
30. 40. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
40. 50. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
50. 60. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
60. 70. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
70. 80. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
80. 90. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
90. 100. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
100. 110. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
110. 120. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
120. 130. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
130. 140. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
140. 150. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
150. 160. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
160. 170. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
170. 180. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
180. 190. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
190. 200. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
200. 210. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
210. 220. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
220. 230. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
230. 240. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
240. 250. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
250. 260. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
260. 270. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
270. 275. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
275. 280. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
280. 290. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
290. 300. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
300. 310. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
310. 320. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
320. 330. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
330. 340. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
340. 341. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
341. 350. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
350. 360. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
360. 370. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
370. 371. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
371. 380. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
22
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
380. 390. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
390. 391. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
391. 392. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
392. 393. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
393. 394. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
394. 511. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
511. 512. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
512. 513. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
513. 514. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
514. 515. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
515. 516. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
516. 517. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
517. 518. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
518. 519. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
519. 601. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
601. 602. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
602. 603. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
603. 604. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
394. 395. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
395. 396. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
396. 397. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
397. 400. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
400. 410. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
410. 460. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
WIND LOADING #: 1
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... 1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 2
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... -1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 3
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... 1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
24
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
WIND LOADING #: 4
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... -1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WAVE VECTOR 1
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and 1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1100.000
2 22800.000 800.000
3 45600.000 300.000
4 0.000 0.000
25
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 2
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and -1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: -1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1100.000
2 22800.000 800.000
3 45600.000 300.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 3
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and 0.000 1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
26
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
WAVE VECTOR 4
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and 0.000 -1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 0.000 -1.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1100.000
2 22800.000 800.000
3 45600.000 300.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
27
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
Rigid X;
80 Rigid Z;
Rigid +Y
1 (HYD) 6036 -63966 -7 0 0 0
2 (HYD) 7290 -61963 -32 0 0 0
3 (HYD) 4733 -67359 -151 0 0 0
4 (HYD) 5833 -63172 3351 0 0 0
5 (HYD) 6166 -64475 -3408 0 0 0
MAX 7290/ 2 67359/ 3 3408/ 5 0/ 1 0/ 1 0/ 1
Rigid X;
120
Rigid Z
1 (HYD) -1003 -100 11 0 0 0
2 (HYD) 4484 448 84 0 0 0
3 (HYD) -7073 -707 284 0 0 0
4 (HYD) -1114 -111 4610 0 0 0
5 (HYD) -1335 -134 -4484 0 0 0
MAX 7073/ 3 707/ 3 4610/ 4 0/ 1 0/ 1 0/ 1
Rigid X;
150
Rigid Z
1 (HYD) -613 -61 -39 0 0 0
2 (HYD) 2605 261 -135 0 0 0
3 (HYD) -3794 -379 -546 0 0 0
4 (HYD) -836 -84 3505 0 0 0
5 (HYD) -552 -55 -3846 0 0 0
MAX 3794/ 3 379/ 3 3846/ 5 0/ 1 0/ 1 0/ 1
Rigid X;
170
Rigid Z
1 (HYD) -271 -27 153 0 0 0
2 (HYD) 979 98 211 0 0 0
3 (HYD) -172 -17 1006 0 0 0
38
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
Rigid X;
190
Rigid Z
1 (HYD) -1226 -123 -437 0 0 0
2 (HYD) -465 -46 -409 0 0 0
3 (HYD) -7430 -743 -2282 0 0 0
4 (HYD) -2517 -252 543 0 0 0
5 (HYD) -3524 -352 -2882 0 0 0
MAX 7430/ 3 743/ 3 2882/ 5 0/ 1 0/ 1 0/ 1
Rigid X;
210
Rigid Z
1 (HYD) 2790 279 1807 0 0 0
2 (HYD) 2247 225 1200 0 0 0
3 (HYD) 13813 1381 6071 0 0 0
4 (HYD) 4411 441 2188 0 0 0
5 (HYD) 7223 722 3864 0 0 0
MAX 13813/ 3 1381/ 3 6071/ 3 0/ 1 0/ 1 0/ 1
290 Flex +Y
1 (HYD) -2537 -3752 -679 0 0 0
2 (HYD) -3657 -5480 -1159 0 0 0
3 (HYD) -1907 -2760 310 0 0 0
4 (HYD) -3451 -4973 452 0 0 0
5 (HYD) -2242 -4185 -1885 0 0 0
MAX 3657/ 2 5480/ 2 1885/ 5 0/ 1 0/ 1 0/ 1
300 Flex +Y
1 (HYD) -4961 -7850 -2363 0 0 0
2 (HYD) -5285 -8486 -2711 0 0 0
3 (HYD) -4109 -6475 -1913 0 0 0
4 (HYD) -4941 -8256 -2997 0 0 0
5 (HYD) -4845 -7401 -1835 0 0 0
MAX 5285/ 2 8486/ 2 2997/ 4 0/ 1 0/ 1 0/ 1
310 Flex +Y
1 (HYD) -4589 -7307 -2260 0 0 0
2 (HYD) -3422 -7022 -1446 0 0 0
3 (HYD) -4581 -6915 -1565 0 0 0
4 (HYD) -4609 -7189 -2021 0 0 0
5 (HYD) -4196 -6804 -2253 0 0 0
MAX 4609/ 4 7307/ 1 2260/ 1 0/ 1 0/ 1 0/ 1
320 Flex +Y
1 (HYD) -1938 -6901 4425 0 0 0
2 (HYD) -67 -6613 4628 0 0 0
39
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
330 Flex +Y
1 (HYD) 4276 -6659 -1857 0 0 0
2 (HYD) 4438 -6540 -1124 0 0 0
3 (HYD) -2852 -6777 -3791 0 0 0
4 (HYD) 4564 -6753 -1231 0 0 0
5 (HYD) 2922 -6493 -3482 0 0 0
MAX 4564/ 4 6777/ 3 3791/ 3 0/ 1 0/ 1 0/ 1
340 Flex +Y
1 (HYD) 1927 -6469 -4098 0 0 0
2 (HYD) 1984 -6438 -4046 0 0 0
3 (HYD) 1514 -6543 -4323 0 0 0
4 (HYD) 1944 -6614 -4202 0 0 0
5 (HYD) 1854 -6346 -4036 0 0 0
MAX 1984/ 2 6614/ 4 4323/ 3 0/ 1 0/ 1 0/ 1
341 Flex +Y
1 (HYD) 1500 -5232 -3341 0 0 0
2 (HYD) 1514 -5207 -3316 0 0 0
3 (HYD) 1372 -5264 -3420 0 0 0
4 (HYD) 1521 -5336 -3411 0 0 0
5 (HYD) 1466 -5149 -3293 0 0 0
MAX 1521/ 4 5336/ 4 3420/ 3 0/ 1 0/ 1 0/ 1
350 Flex +Y
1 (HYD) 568 -1995 -1275 0 0 0
2 (HYD) 571 -1981 -1264 0 0 0
3 (HYD) 530 -2004 -1299 0 0 0
4 (HYD) 575 -2028 -1298 0 0 0
5 (HYD) 558 -1967 -1259 0 0 0
MAX 575/ 4 2028/ 4 1299/ 3 0/ 1 0/ 1 0/ 1
360 Flex +Y
1 (HYD) 1528 -4658 -2881 0 0 0
2 (HYD) 1518 -4589 -2831 0 0 0
3 (HYD) 1470 -4697 -2941 0 0 0
4 (HYD) 1540 -4701 -2908 0 0 0
5 (HYD) 1506 -4620 -2862 0 0 0
MAX 1540/ 4 4701/ 4 2941/ 3 0/ 1 0/ 1 0/ 1
370 Flex +Y
1 (HYD) 2496 -6741 -4005 0 0 0
2 (HYD) 2484 -6625 -3916 0 0 0
3 (HYD) 2435 -6869 -4145 0 0 0
40
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
371 Flex +Y
1 (HYD) 2814 -8322 -5100 0 0 0
2 (HYD) 2826 -8179 -4979 0 0 0
3 (HYD) 2733 -8467 -5259 0 0 0
4 (HYD) 2829 -8336 -5103 0 0 0
5 (HYD) 2784 -8318 -5114 0 0 0
MAX 2829/ 4 8467/ 3 5259/ 3 0/ 1 0/ 1 0/ 1
391 Flex +Y
1 (HYD) 1198 -3890 -2445 0 0 0
2 (HYD) 1210 -3829 -2391 0 0 0
3 (HYD) 1159 -3947 -2508 0 0 0
4 (HYD) 1204 -3890 -2443 0 0 0
5 (HYD) 1187 -3893 -2453 0 0 0
MAX 1210/ 2 3947/ 3 2508/ 3 0/ 1 0/ 1 0/ 1
392 Flex +Y
1 (HYD) 1960 -7339 -4748 0 0 0
2 (HYD) 1999 -7246 -4662 0 0 0
3 (HYD) 1888 -7422 -4840 0 0 0
4 (HYD) 1971 -7334 -4740 0 0 0
5 (HYD) 1944 -7349 -4763 0 0 0
MAX 1999/ 2 7422/ 3 4840/ 3 0/ 1 0/ 1 0/ 1
393 Flex +Y
1 (HYD) 1506 -6193 -4065 0 0 0
2 (HYD) 1546 -6129 -4002 0 0 0
3 (HYD) 1450 -6260 -4135 0 0 0
4 (HYD) 1515 -6188 -4058 0 0 0
5 (HYD) 1495 -6203 -4077 0 0 0
MAX 1546/ 2 6260/ 3 4135/ 3 0/ 1 0/ 1 0/ 1
394 Flex +Y
1 (HYD) 1454 -6426 -4257 0 0 0
2 (HYD) 1504 -6371 -4199 0 0 0
3 (HYD) 1401 -6505 -4332 0 0 0
4 (HYD) 1464 -6420 -4249 0 0 0
5 (HYD) 1445 -6437 -4268 0 0 0
MAX 1504/ 2 6505/ 3 4332/ 3 0/ 1 0/ 1 0/ 1
395 Flex +Y
1 (HYD) 1902 -8968 -5982 0 0 0
2 (HYD) 1980 -8893 -5902 0 0 0
3 (HYD) 1834 -9105 -6104 0 0 0
4 (HYD) 1914 -8956 -5970 0 0 0
41
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
400 Flex +Y
1 (HYD) 2149 -10688 -7166 0 0 0
2 (HYD) 2232 -10554 -7043 0 0 0
3 (HYD) 2088 -10897 -7336 0 0 0
4 (HYD) 2159 -10671 -7150 0 0 0
5 (HYD) 2142 -10712 -7186 0 0 0
MAX 2232/ 2 10897/ 3 7336/ 3 0/ 1 0/ 1 0/ 1
410 Flex +Y
1 (HYD) 1191 -5857 -3923 0 0 0
2 (HYD) 1211 -5761 -3846 0 0 0
3 (HYD) 1180 -5982 -4017 0 0 0
4 (HYD) 1194 -5847 -3915 0 0 0
5 (HYD) 1191 -5871 -3934 0 0 0
MAX 1211/ 2 5982/ 3 4017/ 3 0/ 1 0/ 1 0/ 1
516 Flex +Y
1 (HYD) 1615 -6917 -4564 0 0 0
2 (HYD) 1657 -6862 -4509 0 0 0
3 (HYD) 1549 -6961 -4620 0 0 0
4 (HYD) 1622 -6914 -4560 0 0 0
5 (HYD) 1605 -6924 -4573 0 0 0
MAX 1657/ 2 6961/ 3 4620/ 3 0/ 1 0/ 1 0/ 1
602 Flex +Y
1 (HYD) 2377 -9747 -6396 0 0 0
2 (HYD) 2425 -9682 -6329 0 0 0
3 (HYD) 2272 -9753 -6438 0 0 0
4 (HYD) 2388 -9749 -6393 0 0 0
5 (HYD) 2361 -9753 -6406 0 0 0
MAX 2425/ 2 9753/ 3 6438/ 3 0/ 1 0/ 1 0/ 1
Displ.
800
Reaction
1 (HYD) 6036 -63966 -7 0 0 0
2 (HYD) 7290 -61963 -32 0 0 0
3 (HYD) 4733 -67359 -151 0 0 0
4 (HYD) 5833 -63172 3351 0 0 0
42
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
Displ.
1000
Reaction
1 (HYD) -1762 -4562 2 0 0 0
2 (HYD) -1386 -4521 7 0 0 0
3 (HYD) -1912 -4784 41 0 0 0
4 (HYD) -1672 -4625 625 0 0 0
5 (HYD) -1789 -4550 -611 0 0 0
MAX 1912/ 3 4784/ 3 625/ 4 0/ 1 0/ 1 0/ 1
Displ.
1200
Reaction
1 (HYD) -1003 -100 11 0 0 0
2 (HYD) 4484 448 84 0 0 0
3 (HYD) -7073 -707 284 0 0 0
4 (HYD) -1114 -111 4610 0 0 0
5 (HYD) -1335 -134 -4484 0 0 0
MAX 7073/ 3 707/ 3 4610/ 4 0/ 1 0/ 1 0/ 1
Displ.
1500
Reaction
1 (HYD) -613 -61 -39 0 0 0
2 (HYD) 2605 261 -135 0 0 0
3 (HYD) -3794 -379 -546 0 0 0
4 (HYD) -836 -84 3505 0 0 0
5 (HYD) -552 -55 -3846 0 0 0
MAX 3794/ 3 379/ 3 3846/ 5 0/ 1 0/ 1 0/ 1
Displ.
1700
Reaction
1 (HYD) -271 -27 153 0 0 0
2 (HYD) 979 98 211 0 0 0
3 (HYD) -172 -17 1006 0 0 0
4 (HYD) 129 13 1367 0 0 0
5 (HYD) 243 24 -439 0 0 0
MAX 979/ 2 98/ 2 1367/ 4 0/ 1 0/ 1 0/ 1
Displ.
1900
Reaction
1 (HYD) -1226 -123 -437 0 0 0
2 (HYD) -465 -46 -409 0 0 0
3 (HYD) -7430 -743 -2282 0 0 0
4 (HYD) -2517 -252 543 0 0 0
5 (HYD) -3524 -352 -2882 0 0 0
MAX 7430/ 3 743/ 3 2882/ 5 0/ 1 0/ 1 0/ 1
2100 Displ.
43
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
Displ.
4600
Reaction
1 (HYD) -19465 -3508 61387 0 0 0
2 (HYD) -19774 -3375 62826 0 0 0
3 (HYD) -20609 -3631 64593 0 0 0
4 (HYD) -19440 -3498 61348 0 0 0
5 (HYD) -19447 -3522 61294 0 0 0
MAX 20609/ 3 3631/ 3 64593/ 3 0/ 1 0/ 1 0/ 1
44
C A E S A R I I VER.5.00.7, (Build 070122) APR 13,2007 18:20:28
Jobname: D:\SAKTHI\CAESAR\STD\10LINE\LATERAL\3 BENDS CONN\RISER10-HY-L
Licensed To: B & W ID: 13709
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 10 235.95 448.15 52.6 20 235.95 448.15 52.6
2 (HYD) 10 235.95 448.15 52.6 20 235.95 448.15 52.6
3 (HYD) 10 235.95 448.15 52.6 20 235.95 448.15 52.6
4 (HYD) 10 235.95 448.15 52.6 20 235.95 448.15 52.6
5 (HYD) 10 235.95 448.15 52.6 20 235.95 448.15 52.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (HYD) 20 235.95 448.15 52.6 30 235.95 448.15 52.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 80 235.95 448.15 52.6 90 235.95 448.15 52.6
2 (HYD) 80 235.95 448.15 52.6 90 235.95 448.15 52.6
3 (HYD) 80 235.95 448.15 52.6 90 235.95 448.15 52.6
4 (HYD) 80 235.95 448.15 52.6 90 235.95 448.15 52.6
5 (HYD) 80 235.95 448.15 52.6 90 235.95 448.15 52.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 130 235.46 448.15 52.5 140 234.92 448.15 52.4
4 (HYD) 130 235.46 448.15 52.5 140 234.92 448.15 52.4
5 (HYD) 130 235.46 448.15 52.5 140 234.92 448.15 52.4
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (HYD) 180 233.46 448.15 52.1 190 232.93 448.15 52.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 240 231.16 448.15 51.6 250 231.16 448.15 51.6
2 (HYD) 240 231.16 448.15 51.6 250 231.16 448.15 51.6
3 (HYD) 240 231.16 448.15 51.6 250 231.16 448.15 51.6
4 (HYD) 240 231.16 448.15 51.6 250 231.16 448.15 51.6
5 (HYD) 240 231.16 448.15 51.6 250 231.16 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 280 231.04 448.15 51.6 290 231.04 448.15 51.6
4 (HYD) 280 231.04 448.15 51.6 290 231.04 448.15 51.6
5 (HYD) 280 231.04 448.15 51.6 290 231.04 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (HYD) 330 231.04 448.15 51.6 340 231.04 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 371 0.00 0.00 0.0 380 0.00 0.00 0.0
2 (HYD) 371 0.00 0.00 0.0 380 0.00 0.00 0.0
3 (HYD) 371 0.00 0.00 0.0 380 0.00 0.00 0.0
4 (HYD) 371 0.00 0.00 0.0 380 0.00 0.00 0.0
5 (HYD) 371 0.00 0.00 0.0 380 0.00 0.00 0.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 393 231.04 448.15 51.6 394 231.04 448.15 51.6
4 (HYD) 393 231.04 448.15 51.6 394 231.04 448.15 51.6
5 (HYD) 393 231.04 448.15 51.6 394 231.04 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (HYD) 514 0.00 0.00 0.0 515 0.00 0.00 0.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 601 231.13 448.15 51.6 602 231.13 448.15 51.6
2 (HYD) 601 231.13 448.15 51.6 602 231.13 448.15 51.6
3 (HYD) 601 231.13 448.15 51.6 602 231.13 448.15 51.6
4 (HYD) 601 231.13 448.15 51.6 602 231.13 448.15 51.6
5 (HYD) 601 231.13 448.15 51.6 602 231.13 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 396 0.00 0.00 0.0 397 0.00 0.00 0.0
4 (HYD) 396 0.00 0.00 0.0 397 0.00 0.00 0.0
5 (HYD) 396 0.00 0.00 0.0 397 0.00 0.00 0.0
CAESAR II
LOAD CONDITION DESCRIPTION
RUN
OPERATION + 100 YEAR
OPERATION 1
ENVIRONMENTAL LOAD
HYDROTEST + 1 YEAR
HYDROTEST 2
ENVIRONMENTAL LOAD
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 48 of 49
1
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
Table of Contents
INPUT LISTING .................................................................................................................................................... 2
MISCELLANEOUS COMPUTED DATA ..................................................................................................................... 19
Displacements 1 (OPE) W+D5+T1+P1....................................................................................................... 27
Displacements 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1............................................................................ 29
Displacements 3 (OPE) W+D2+D5+T1+P1+WIN2+WAV2............................................................................ 31
Displacements 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3............................................................................ 33
Displacements 5 (OPE) W+D4+D5+T1+P1+WIN4+WAV4............................................................................ 35
Restraint Summary 1 (OPE) W+D5+T1+P1 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1 3 (OPE)
W+D2+D5+T1+P1+WIN2+WAV2 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3 5 (OPE)
W+D4+D5+T1+P1+WIN4+WAV4.............................................................................................................................. 37
Stresses 1 (OPE) W+D5+T1+P1................................................................................................................ 43
Stresses 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1..................................................................................... 47
Stresses 3 (OPE) W+D2+D5+T1+P1+WIN2+WAV2..................................................................................... 51
Stresses 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3..................................................................................... 55
Stresses 5 (OPE) W+D4+D5+T1+P1+WIN4+WAV4..................................................................................... 59
Code Compliance Extended 1 (OPE) W+D5+T1+P1 2 (OPE) W+D1+D5+T1+P1+WIN1+WAV1 3
(OPE) W+D2+D5+T1+P1+WIN2+WAV2 4 (OPE) W+D3+D5+T1+P1+WIN3+WAV3 5 (OPE)
W+D4+D5+T1+P1+WIN4+WAV4 63
2
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
Job Description:
ANALYST: SV
PIPE DATA
-----------------------------------------------------------------------------
-----------------------------------------------------------------------------
From 10 To 20 DX= 5,000.000 mm.
PIPE
Dia= 406.400 mm. Wall= 23.800 mm. Insul= .450 mm. Cor= 3.0000 mm.
GENERAL
T1= 22 C P1= 186.6000 bars Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m. Insul= 1,440.0000 kg/cu.m.
Fluid=1025.0000000 kg/cu.m.
RESTRAINTS
Node 10 ANC Cnode 1000
DISPLACEMENTS
Node 1000 DX1= 34.700 mm. DY1= -27.900 mm. DZ1= 2.000 mm.
DX2= -169.700 mm. DY2= -32.200 mm. DZ2= -2.000 mm. DX3= -24.600 mm.
DY3= -28.700 mm. DZ3= 41.100 mm. DX4= -26.300 mm. DY4= -28.600 mm.
DZ4= -85.300 mm.
WIND
Wind Shape= .500
ALLOWABLE STRESSES
B31.4 IX (2002) Sy= 448 N./sq.mm. Fac= .6000
-----------------------------------------------------------------------------
From 20 To 30 DX= 3,500.000 mm.
BEND at "TO" end
Radius= 2,032.000 mm. (user) Bend Angle= 90.000
-----------------------------------------------------------------------------
From 30 To 40 DY= -4,500.000 mm.
BEND at "TO" end
Radius= 2,032.000 mm. (user) Bend Angle= 5.711
-----------------------------------------------------------------------------
From 40 To 50 DX= 218.100 mm. DY= -2,181.000 mm.
-----------------------------------------------------------------------------
From 50 To 60 DX= 31.900 mm. DY= -319.000 mm.
RIGID Weight= 5,564.45 N.
-----------------------------------------------------------------------------
From 60 To 70 DX= 31.900 mm. DY= -319.000 mm.
RIGID Weight= 5,564.45 N.
-----------------------------------------------------------------------------
From 70 To 80 DX= 118.100 mm. DY= -1,181.000 mm.
RESTRAINTS
Node 80 X Cnode 800 Dir Vec= .9950 .0995 .0000
Node 80 Z Cnode 800
Node 80 +Y Cnode 800
DISPLACEMENTS
Node 800 DX1= 31.500 mm. DY1= -28.300 mm. DZ1= 1.600 mm.
3
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
DX2= -163.100 mm. DY2= -31.700 mm. DZ2= -.400 mm. DX3= -24.000 mm.
DY3= -28.700 mm. DZ3= 39.500 mm. DX4= -26.800 mm. DY4= -28.800 mm.
DZ4= -81.600 mm.
-----------------------------------------------------------------------------
From 80 To 90 DX= 500.000 mm. DY= -5,000.000 mm.
-----------------------------------------------------------------------------
From 90 To 100 DX= 100.000 mm. DY= -1,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 74.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 100 To 110 DX= 100.000 mm. DY= -1,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 96.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 110 To 120 DX= 90.000 mm. DY= -900.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 119.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 120 To 130 DX= 160.000 mm. DY= -1,600.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 153.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 130 To 140 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 153.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 140 To 150 DX= 350.000 mm. DY= -3,500.000 mm.
GENERAL
RESTRAINTS
Node 150 X Cnode 1500 Dir Vec= .9950 .0995 .0000
Node 150 Z Cnode 1500
DISPLACEMENTS
Node 1500 DX1= 24.700 mm. DY1= -29.200 mm. DZ1= .700 mm.
DX2= -149.200 mm. DY2= -30.600 mm. DZ2= 2.900 mm. DX3= -22.700 mm.
DY3= -28.800 mm. DZ3= 36.100 mm. DX4= -27.900 mm. DY4= -29.200 mm.
DZ4= -73.700 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 148.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 150 To 160 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 144.000 Mar. Growth Dens.= 1,400.000
4
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
-----------------------------------------------------------------------------
From 160 To 170 DX= 230.000 mm. DY= -2,300.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 139.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 170 To 180 DX= 270.000 mm. DY= -2,700.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 139.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 180 To 190 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
RESTRAINTS
Node 190 X Cnode 1900 Dir Vec= .9950 .0995 .0000
Node 190 Z Cnode 1900
DISPLACEMENTS
Node 1900 DX1= 12.800 mm. DY1= -30.500 mm. DZ1= .000 mm.
DX2= -117.000 mm. DY2= -27.500 mm. DZ2= -1.100 mm. DX3= -20.700 mm.
DY3= -28.700 mm. DZ3= 25.200 mm. DX4= -24.300 mm. DY4= -28.900 mm.
DZ4= -58.900 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 133.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 190 To 200 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 128.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 200 To 210 DX= 350.000 mm. DY= -3,500.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 122.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 210 To 220 DX= 190.000 mm. DY= -1,900.000 mm.
GENERAL
RESTRAINTS
Node 220 X Cnode 2200 Dir Vec= .9950 .0995 .0000
Node 220 Z Cnode 2200
DISPLACEMENTS
Node 2200 DX1= 4.600 mm. DY1= -31.400 mm. DZ1= -.500 mm.
DX2= -94.700 mm. DY2= -25.400 mm. DZ2= -3.900 mm. DX3= -19.300 mm.
DY3= -28.600 mm. DZ3= 17.700 mm. DX4= -21.800 mm. DY4= -28.700 mm.
DZ4= -48.600 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 119.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 220 To 230 DX= 336.400 mm. DY= -3,364.000 mm.
GENERAL
5
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 119.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 230 To 240 DX= 208.800 mm. DY= -2,088.000 mm.
PIPE
Dia= 406.400 mm. Wall= 22.860 mm. Insul= .450 mm.
GENERAL
BEND at "TO" end
Radius= 2,032.000 mm. (user) Bend Angle= 84.745
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 112.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 240 To 250 DX= 2,635.400 mm. DZ= 1,118.700 mm.
PIPE
Dia= 406.400 mm. Wall= 23.800 mm. Insul= .450 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 85.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 250 To 260 DX= 295.500 mm. DZ= 125.400 mm.
PIPE
Dia= 406.400 mm. Wall= 23.800 mm. Insul= .450 mm.
GENERAL
RIGID Weight= 5,564.45 N.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 85.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 260 To 270 DX= 295.500 mm. DZ= 125.400 mm.
GENERAL
RIGID Weight= 5,564.45 N.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 75.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 270 To 271 DX= 1,531.700 mm. DZ= 650.200 mm.
PIPE
Dia= 406.400 mm. Wall= 22.860 mm. Insul= .450 mm.
GENERAL
BEND at "TO" end
Radius= 2,032.000 mm. (user) Bend Angle= 29.999
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 75.000 Mar. Growth Dens.= 1,400.000
-----------------------------------------------------------------------------
From 271 To 280 DX= 2,462.400 mm. DY= -1,544.400 mm. DZ= 1,045.200 mm.
GENERAL
BEND at "TO" end
Radius= 2,032.000 mm. (user) Bend Angle= 29.999
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 75.000 Mar. Growth Dens.= 1,400.000
6
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
-----------------------------------------------------------------------------
From 280 To 290 DX= 2,301.300 mm. DZ= 976.800 mm.
PIPE
Dia= 406.400 mm. Wall= 23.800 mm. Insul= .450 mm.
GENERAL
RESTRAINTS
Node 290 +Y K= 183 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 290 To 300 DX= 4,602.500 mm. DZ= 1,953.700 mm.
GENERAL
RESTRAINTS
Node 300 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 300 To 310 DX= 4,602.500 mm. DZ= 1,953.700 mm.
GENERAL
RESTRAINTS
Node 310 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 310 To 320 DX= 4,602.500 mm. DZ= 1,953.700 mm.
GENERAL
RESTRAINTS
Node 320 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 320 To 330 DX= 4,602.500 mm. DZ= 1,953.700 mm.
GENERAL
RESTRAINTS
Node 330 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 330 To 340 DX= 4,602.500 mm. DZ= 1,953.700 mm.
GENERAL
RESTRAINTS
Node 340 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 340 To 341 DX= 1,288.700 mm. DZ= 547.000 mm.
GENERAL
RESTRAINTS
Node 341 +Y K= 102 N./mm. Mu = .70
7
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 341 To 350 DX= 4,602.500 mm. DZ= 1,953.700 mm.
GENERAL
RESTRAINTS
Node 350 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 350 To 360 DX= 3,682.000 mm. DZ= 1,562.900 mm.
RESTRAINTS
Node 360 +Y K= 292 N./mm. Mu = .70
-----------------------------------------------------------------------------
From 360 To 370 DX= 2,301.300 mm. DZ= 976.800 mm.
PIPE
Dia= 406.400 mm. Wall= 22.860 mm. Insul= .450 mm.
GENERAL
BEND at "TO" end
Radius= 2,032.000 mm. (user) Bend Angle= 80.501
RESTRAINTS
Node 370 +Y K= 183 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 370 To 380 DX= -1,167.200 mm. DZ= 4,861.800 mm.
PIPE
Dia= 406.400 mm. Wall= 23.800 mm. Insul= .450 mm.
GENERAL
RESTRAINTS
Node 380 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 380 To 381 DX= -466.900 mm. DZ= 1,944.700 mm.
GENERAL
RESTRAINTS
Node 381 +Y K= 146 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
SIF's & TEE's
Node 381 Welding Tee
-----------------------------------------------------------------------------
From 381 To 505 DX= 782.800 mm. DZ= 187.900 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 505 To 506 DX= 311.818 mm. DZ= 74.848 mm.
8
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
GENERAL
RIGID Weight= 5,564.45 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 381 To 382 DX= -1,139.000 mm. DZ= 4,744.200 mm.
GENERAL
RESTRAINTS
Node 382 +Y K= 380 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 382 To 390 DX= -74.805 mm. DZ= 311.828 mm.
GENERAL
RIGID Weight= 5,564.45 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 390 To 400 DX= -74.805 mm. DZ= 311.828 mm.
GENERAL
RIGID Weight= 5,564.45 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 400 To 410 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
Node 410 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 410 To 420 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
Node 420 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 420 To 430 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
Node 430 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
Marine Growth= .000
-----------------------------------------------------------------------------
From 430 To 440 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
9
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
MATERIAL Changes:
10 20 Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
10
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
BEND ELEMENTS
20 30 Radius= 2,032.000 mm. (user)
Bend Angle= 90.000
30 40 Radius= 2,032.000 mm. (user)
Bend Angle= 5.711
230 240 Radius= 2,032.000 mm. (user)
Bend Angle= 84.745
270 271 Radius= 2,032.000 mm. (user)
Bend Angle= 29.999
271 280 Radius= 2,032.000 mm. (user)
Bend Angle= 29.999
360 370 Radius= 2,032.000 mm. (user)
Bend Angle= 80.501
RIGIDS
50 60 RIGID Weight= 5,564.45 N.
60 70 RIGID Weight= 5,564.45 N.
250 260 RIGID Weight= 5,564.45 N.
260 270 RIGID Weight= 5,564.45 N.
505 506 RIGID Weight= 5,564.45 N.
382 390 RIGID Weight= 5,564.45 N.
390 400 RIGID Weight= 5,564.45 N.
RESTRAINTS Len MU
GAP YIELD Dir
NODE TYPE CNODE STIF1 STIF2 FORCE Vectors
-------+-------+------+----------+----------+----------+---------------------
10 ANC 1000 .000 .000 .000
80 X 800 .995 .100 .000
80 Z 800 .000 .000 1.000
80 +Y 800 .000 1.000 .000
150 X 1500 .995 .100 .000
150 Z 1500 .000 .000 1.000
190 X 1900 .995 .100 .000
190 Z 1900 .000 .000 1.000
220 X 2200 .995 .100 .000
220 Z 2200 .000 .000 1.000
290 +Y 183 .70 .000 1.000 .000
300 +Y 365 .70 .000 1.000 .000
11
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
DISPLACEMENTS
10 20 Node 1000 DX1= 34.700 mm. DY1= -27.900 mm.
DZ1= 2.000 mm. DX2= -169.700 mm.
DY2= -32.200 mm. DZ2= -2.000 mm.
DX3= -24.600 mm. DY3= -28.700 mm.
DZ3= 41.100 mm. DX4= -26.300 mm.
DY4= -28.600 mm. DZ4= -85.300 mm.
70 80 Node 800 DX1= 31.500 mm. DY1= -28.300 mm.
DZ1= 1.600 mm. DX2= -163.100 mm.
DY2= -31.700 mm. DZ2= -.400 mm.
DX3= -24.000 mm. DY3= -28.700 mm.
DZ3= 39.500 mm. DX4= -26.800 mm.
DY4= -28.800 mm. DZ4= -81.600 mm.
140 150 Node 1500 DX1= 24.700 mm. DY1= -29.200 mm.
DZ1= .700 mm. DX2= -149.200 mm.
DY2= -30.600 mm. DZ2= 2.900 mm.
DX3= -22.700 mm. DY3= -28.800 mm.
DZ3= 36.100 mm. DX4= -27.900 mm.
DY4= -29.200 mm. DZ4= -73.700 mm.
180 190 Node 1900 DX1= 12.800 mm. DY1= -30.500 mm.
DZ1= .000 mm. DX2= -117.000 mm.
DY2= -27.500 mm. DZ2= -1.100 mm.
DX3= -20.700 mm. DY3= -28.700 mm.
DZ3= 25.200 mm. DX4= -24.300 mm.
DY4= -28.900 mm. DZ4= -58.900 mm.
210 220 Node 2200 DX1= 4.600 mm. DY1= -31.400 mm.
DZ1= -.500 mm. DX2= -94.700 mm.
DY2= -25.400 mm. DZ2= -3.900 mm.
DX3= -19.300 mm. DY3= -28.600 mm.
DZ3= 17.700 mm. DX4= -21.800 mm.
DY4= -28.700 mm. DZ4= -48.600 mm.
12
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
490 500 Node 5000 DX5= 23.300 mm. DY5= .000 mm.
DZ5= -97.200 mm.
WIND/WAVE
10 20 WIND Wind Shape= .500
90 100 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 74.000
Mar. Growth Dens.= 1,400.000
100 110 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 96.000
Mar. Growth Dens.= 1,400.000
110 120 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 119.000
Mar. Growth Dens.= 1,400.000
120 130 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 153.000
Mar. Growth Dens.= 1,400.000
130 140 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 153.000
Mar. Growth Dens.= 1,400.000
140 150 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 148.000
Mar. Growth Dens.= 1,400.000
150 160 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 144.000
Mar. Growth Dens.= 1,400.000
160 170 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 139.000
Mar. Growth Dens.= 1,400.000
170 180 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 139.000
Mar. Growth Dens.= 1,400.000
180 190 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 133.000
Mar. Growth Dens.= 1,400.000
190 200 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 128.000
Mar. Growth Dens.= 1,400.000
200 210 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
Marine Growth= 122.000
Mar. Growth Dens.= 1,400.000
13
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
COORDINATE REPORT
/--------------------(mm.)----------------------/
NODE X Y Z
10 .0000 13500.0000 .0000
20 5000.0000 13500.0000 .0000
30 8500.0000 13500.0000 .0000
40 8500.0000 9000.0000 .0000
50 8718.0996 6819.0000 .0000
60 8750.0000 6500.0000 .0000
70 8781.9004 6181.0000 .0000
80 8900.0000 5000.0000 .0000
90 9400.0000 .0000 .0000
100 9500.0000 -1000.0000 .0000
110 9600.0000 -2000.0000 .0000
120 9690.0000 -2900.0000 .0000
130 9850.0000 -4500.0000 .0000
140 10350.0000 -9500.0000 .0000
150 10700.0000 -13000.0000 .0000
160 11200.0000 -18000.0000 .0000
170 11430.0000 -20300.0000 .0000
180 11700.0000 -23000.0000 .0000
190 12200.0000 -28000.0000 .0000
200 12700.0000 -33000.0000 .0000
210 13050.0000 -36500.0000 .0000
220 13240.0000 -38400.0000 .0000
230 13576.4004 -41764.0000 .0000
240 13785.2002 -43852.0000 .0000
250 16420.5996 -43852.0000 1118.7000
260 16716.0996 -43852.0000 1244.1000
270 17011.5996 -43852.0000 1369.5000
271 18543.2988 -43852.0000 2019.7000
280 21005.6992 -45396.3984 3064.8999
290 23307.0000 -45396.3984 4041.7000
300 27909.5000 -45396.3984 5995.3999
310 32512.0000 -45396.3984 7949.0996
320 37114.5000 -45396.3984 9902.7998
330 41717.0000 -45396.3984 11856.5000
340 46319.5000 -45396.3984 13810.2002
341 47608.1992 -45396.3984 14357.2002
350 52210.6992 -45396.3984 16310.9004
360 55892.6992 -45396.3984 17873.8008
370 58194.0000 -45396.3984 18850.6016
380 57026.8008 -45396.3984 23712.4023
381 56559.9023 -45396.3984 25657.1016
505 57342.7031 -45396.3984 25845.0020
506 57654.5195 -45396.3984 25919.8496
381 56559.9023 -45396.3984 25657.1016
382 55420.9023 -45396.3984 30401.3008
390 55346.0977 -45396.3984 30713.1289
400 55271.2930 -45396.3984 31024.9570
18
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
INPUT LISTING
BEND DATA:
10 20
TYPE KEY:
3 - Welding Tee
4 - Sweepolet
5 - Weldolet
10. 20. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
20. 30. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
30. 40. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
40. 50. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
50. 60. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
60. 70. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
70. 80. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
80. 90. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
90. 100. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
100. 110. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
110. 120. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
120. 130. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
130. 140. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
140. 150. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
150. 160. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
160. 170. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
170. 180. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
180. 190. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
190. 200. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
200. 210. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
210. 220. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
220. 230. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
230. 240. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
240. 250. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
250. 260. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
260. 270. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
270. 271. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
271. 280. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
280. 290. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
290. 300. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
300. 310. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
310. 320. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
320. 330. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
330. 340. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
340. 341. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
341. 350. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
350. 360. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
360. 370. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
370. 380. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
380. 381. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
381. 505. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
505. 506. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
381. 382. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
382. 390. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
390. 400. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
400. 410. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
410. 420. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
420. 430. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
430. 440. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
440. 450. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
450. 460. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
22
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
460. 470. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
470. 480. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
480. 490. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
490. 500. 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
WIND LOADING #: 1
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... 1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 2
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... -1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 3
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... 1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 4
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... -1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
24
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
WAVE VECTOR 1
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and 1.000 0.000
Wave Theory STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1400.000
2 22800.000 1200.000
3 45600.000 700.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 2
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and -1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
25
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
WAVE VECTOR 3
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and 0.000 1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 0.000 1.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1400.000
2 22800.000 1200.000
3 45600.000 700.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 4
Velocity Units : mm./sec.
26
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
Rigid X;
80 Rigid Z;
Rigid +Y
1 (OPE) 18145 -218195 48 0 0 0
2 (OPE) 65394 -211400 98 0 0 0
3 (OPE) -24348 -224648 156 0 0 0
4 (OPE) 17162 -220469 22901 0 0 0
5 (OPE) 16228 -213312 -26292 0 0 0
MAX 65394/ 2 224648/ 3 26292/ 5 0/ 1 0/ 1 0/ 1
Rigid X;
150
Rigid Z
1 (OPE) -5243 -524 6 0 0 0
2 (OPE) 81804 8180 76 0 0 0
3 (OPE) -78304 -7830 79 0 0 0
4 (OPE) -6633 -663 84345 0 0 0
5 (OPE) -5010 -501 -83042 0 0 0
MAX 81804/ 2 8180/ 2 84345/ 4 0/ 1 0/ 1 0/ 1
Rigid X;
190
Rigid Z
1 (OPE) -2991 -299 -219 0 0 0
2 (OPE) 31411 3141 321 0 0 0
3 (OPE) -46279 -4628 -5300 0 0 0
4 (OPE) -4499 -450 24607 0 0 0
5 (OPE) -10639 -1064 -21489 0 0 0
MAX 46279/ 3 4628/ 3 24607/ 4 0/ 1 0/ 1 0/ 1
Rigid X;
220
Rigid Z
1 (OPE) 10914 1091 6894 0 0 0
2 (OPE) 25628 2563 2082 0 0 0
3 (OPE) 15128 1513 22990 0 0 0
38
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
290 Flex +Y
1 (OPE) -3010 -4439 -772 0 0 0
2 (OPE) 1373 -6936 -3840 0 0 0
3 (OPE) -2973 -4247 -9 0 0 0
4 (OPE) -3808 -8013 4119 0 0 0
5 (OPE) 632 -4127 -2819 0 0 0
MAX 3808/ 4 8013/ 4 4119/ 4 0/ 1 0/ 1 0/ 1
300 Flex +Y
1 (OPE) -7010 -10162 -1213 0 0 0
2 (OPE) 7461 -11851 3626 0 0 0
3 (OPE) -6553 -9382 -430 0 0 0
4 (OPE) -8877 -16718 7626 0 0 0
5 (OPE) 1007 -5797 -3931 0 0 0
MAX 8877/ 4 16718/ 4 7626/ 4 0/ 1 0/ 1 0/ 1
310 Flex +Y
1 (OPE) -7180 -10290 -573 0 0 0
2 (OPE) 6889 -9947 -1013 0 0 0
3 (OPE) -6943 -10033 -1060 0 0 0
4 (OPE) -9746 -16649 6392 0 0 0
5 (OPE) 719 -3951 -2671 0 0 0
MAX 9746/ 4 16649/ 4 6392/ 4 0/ 1 0/ 1 0/ 1
320 Flex +Y
1 (OPE) -6798 -9927 -1440 0 0 0
2 (OPE) -711 -8722 6064 0 0 0
3 (OPE) -6926 -10276 -1942 0 0 0
4 (OPE) -10076 -16249 5278 0 0 0
5 (OPE) 536 -2943 -1989 0 0 0
MAX 10076/ 4 16249/ 4 6064/ 2 0/ 1 0/ 1 0/ 1
330 Flex +Y
1 (OPE) -3373 -9505 -5736 0 0 0
2 (OPE) -1817 -8090 5364 0 0 0
3 (OPE) -6471 -10300 -3180 0 0 0
4 (OPE) -10686 -15794 2835 0 0 0
5 (OPE) 453 -2594 -1758 0 0 0
MAX 10686/ 4 15794/ 4 5736/ 1 0/ 1 0/ 1 0/ 1
340 Flex +Y
1 (OPE) 611 -9315 -6492 0 0 0
2 (OPE) -1680 -7801 5196 0 0 0
3 (OPE) -5568 -10519 -4818 0 0 0
4 (OPE) -6730 -15510 -8519 0 0 0
39
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
341 Flex +Y
1 (OPE) 299 -2613 -1805 0 0 0
2 (OPE) -327 -2170 1484 0 0 0
3 (OPE) -1468 -2990 -1492 0 0 0
4 (OPE) -889 -4332 -2899 0 0 0
5 (OPE) 120 -804 -550 0 0 0
MAX 1468/ 3 4332/ 4 2899/ 4 0/ 1 0/ 1 0/ 1
350 Flex +Y
1 (OPE) 1913 -9751 -6552 0 0 0
2 (OPE) 2191 -7631 -4871 0 0 0
3 (OPE) -4007 -11845 -7259 0 0 0
4 (OPE) 1978 -15587 -10730 0 0 0
5 (OPE) 414 -3724 -2574 0 0 0
MAX 4007/ 3 15587/ 4 10730/ 4 0/ 1 0/ 1 0/ 1
360 Flex +Y
1 (OPE) 1855 -8424 -5598 0 0 0
2 (OPE) 1685 -6056 -3890 0 0 0
3 (OPE) -2526 -10870 -7177 0 0 0
4 (OPE) 2432 -12845 -8656 0 0 0
5 (OPE) 253 -3854 -2686 0 0 0
MAX 2526/ 3 12845/ 4 8656/ 4 0/ 1 0/ 1 0/ 1
370 Flex +Y
1 (OPE) 1631 -5947 -3830 0 0 0
2 (OPE) 1740 -3827 -2037 0 0 0
3 (OPE) -1219 -8134 -5562 0 0 0
4 (OPE) 2225 -8108 -5222 0 0 0
5 (OPE) -56 -3744 -2620 0 0 0
MAX 2225/ 4 8134/ 3 5562/ 3 0/ 1 0/ 1 0/ 1
380 Flex +Y
1 (OPE) 4147 -12999 -8099 0 0 0
2 (OPE) 4909 -7663 -2163 0 0 0
3 (OPE) -1904 -18417 -12750 0 0 0
4 (OPE) 5377 -15580 -9488 0 0 0
5 (OPE) -651 -10494 -7317 0 0 0
MAX 5377/ 4 18417/ 3 12750/ 3 0/ 1 0/ 1 0/ 1
381 Flex +Y
1 (OPE) 1795 -5459 -3374 0 0 0
2 (OPE) 2089 -3083 -544 0 0 0
3 (OPE) -694 -7859 -5457 0 0 0
4 (OPE) 2242 -6150 -3675 0 0 0
5 (OPE) -340 -4819 -3356 0 0 0
40
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
382 Flex +Y
1 (OPE) 4697 -14730 -9179 0 0 0
2 (OPE) 5217 -7464 -281 0 0 0
3 (OPE) -1849 -22023 -15305 0 0 0
4 (OPE) 5528 -15012 -8936 0 0 0
5 (OPE) -761 -14604 -10194 0 0 0
MAX 5528/ 4 22023/ 3 15305/ 3 0/ 1 0/ 1 0/ 1
410 Flex +Y
1 (OPE) 3611 -12878 -8260 0 0 0
2 (OPE) 3740 -5347 155 0 0 0
3 (OPE) -2257 -20423 -14117 0 0 0
4 (OPE) 4156 -12335 -7569 0 0 0
5 (OPE) -17 -13530 -9471 0 0 0
MAX 4156/ 4 20423/ 3 14117/ 3 0/ 1 0/ 1 0/ 1
420 Flex +Y
1 (OPE) 2720 -11310 -7435 0 0 0
2 (OPE) 2584 -3704 210 0 0 0
3 (OPE) -2764 -18933 -12962 0 0 0
4 (OPE) 3151 -10599 -6717 0 0 0
5 (OPE) 574 -12089 -8443 0 0 0
MAX 3151/ 4 18933/ 3 12962/ 3 0/ 1 0/ 1 0/ 1
430 Flex +Y
1 (OPE) 2116 -10272 -6872 0 0 0
2 (OPE) 1872 -2687 190 0 0 0
3 (OPE) -3227 -17878 -12091 0 0 0
4 (OPE) 2493 -9613 -6250 0 0 0
5 (OPE) 956 -10968 -7618 0 0 0
MAX 3227/ 3 17878/ 3 12091/ 3 0/ 1 0/ 1 0/ 1
440 Flex +Y
1 (OPE) 1789 -9883 -6683 0 0 0
2 (OPE) 1582 -2274 174 0 0 0
3 (OPE) -3622 -17517 -11715 0 0 0
4 (OPE) 2139 -9325 -6167 0 0 0
5 (OPE) 1197 -10465 -7227 0 0 0
MAX 3622/ 3 17517/ 3 11715/ 3 0/ 1 0/ 1 0/ 1
450 Flex +Y
1 (OPE) 1644 -9929 -6753 0 0 0
2 (OPE) 1559 -2241 170 0 0 0
3 (OPE) -3883 -17645 -11726 0 0 0
4 (OPE) 1970 -9448 -6313 0 0 0
5 (OPE) 1365 -10431 -7173 0 0 0
MAX 3883/ 3 17645/ 3 11726/ 3 0/ 1 0/ 1 0/ 1
41
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
460 Flex +Y
1 (OPE) 1585 -10044 -6850 0 0 0
2 (OPE) 1643 -2358 162 0 0 0
3 (OPE) -3838 -17758 -11823 0 0 0
4 (OPE) 1875 -9607 -6458 0 0 0
5 (OPE) 1469 -10501 -7203 0 0 0
MAX 3838/ 3 17758/ 3 11823/ 3 0/ 1 0/ 1 0/ 1
470 Flex +Y
1 (OPE) 1508 -9708 -6626 0 0 0
2 (OPE) 1687 -2416 121 0 0 0
3 (OPE) -3200 -17028 -11482 0 0 0
4 (OPE) 1737 -9310 -6282 0 0 0
5 (OPE) 1470 -10128 -6936 0 0 0
MAX 3200/ 3 17028/ 3 11482/ 3 0/ 1 0/ 1 0/ 1
480 Flex +Y
1 (OPE) 1289 -8245 -5626 0 0 0
2 (OPE) 1534 -2192 15 0 0 0
3 (OPE) -1759 -14321 -9869 0 0 0
4 (OPE) 1422 -7918 -5357 0 0 0
5 (OPE) 1287 -8591 -5875 0 0 0
MAX 1759/ 3 14321/ 3 9869/ 3 0/ 1 0/ 1 0/ 1
490 Flex +Y
1 (OPE) 796 -4999 -3407 0 0 0
2 (OPE) 992 -1439 -178 0 0 0
3 (OPE) -39 -8572 -6000 0 0 0
4 (OPE) 827 -4806 -3261 0 0 0
5 (OPE) 810 -5203 -3551 0 0 0
MAX 992/ 2 8572/ 3 6000/ 3 0/ 1 0/ 1 0/ 1
Displ.
800
Reaction
1 (OPE) 18145 -218194 48 0 0 0
2 (OPE) 65394 -211401 98 0 0 0
3 (OPE) -24348 -224647 156 0 0 0
4 (OPE) 17162 -220468 22901 0 0 0
5 (OPE) 16228 -213313 -26292 0 0 0
MAX 65394/ 2 224647/ 3 26292/ 5 0/ 1 0/ 1 0/ 1
42
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
Displ.
1000
Reaction
1 (OPE) -3834 -11296 -32 0 0 0
2 (OPE) -19676 -7090 -38 0 0 0
3 (OPE) 11468 -16235 -23 0 0 0
4 (OPE) -3239 -11577 9 0 0 0
5 (OPE) -3352 -11320 2068 0 0 0
MAX 19676/ 2 16235/ 3 2068/ 5 0/ 1 0/ 1 0/ 1
Displ.
1500
Reaction
1 (OPE) -5243 -524 6 0 0 0
2 (OPE) 81804 8180 76 0 0 0
3 (OPE) -78304 -7830 79 0 0 0
4 (OPE) -6633 -663 84345 0 0 0
5 (OPE) -5010 -501 -83042 0 0 0
MAX 81804/ 2 8180/ 2 84345/ 4 0/ 1 0/ 1 0/ 1
Displ.
1900
Reaction
1 (OPE) -2991 -299 -219 0 0 0
2 (OPE) 31411 3141 321 0 0 0
3 (OPE) -46279 -4628 -5300 0 0 0
4 (OPE) -4499 -450 24607 0 0 0
5 (OPE) -10639 -1064 -21489 0 0 0
MAX 46279/ 3 4628/ 3 24607/ 4 0/ 1 0/ 1 0/ 1
Displ.
2200
Reaction
1 (OPE) 10914 1091 6894 0 0 0
2 (OPE) 25628 2563 2082 0 0 0
3 (OPE) 15128 1513 22990 0 0 0
4 (OPE) 15107 1511 47920 0 0 0
5 (OPE) 20452 2045 -42856 0 0 0
MAX 25628/ 2 2563/ 2 47920/ 4 0/ 1 0/ 1 0/ 1
Displ.
5000
Reaction
1 (OPE) -25254 -8919 104668 0 0 0
2 (OPE) 21653 -1533 3494 0 0 0
3 (OPE) -39937 -16333 132016 0 0 0
4 (OPE) -28476 -8508 120084 0 0 0
5 (OPE) -16421 -9356 66718 0 0 0
MAX 39937/ 3 16333/ 3 132016/ 3 0/ 1 0/ 1 0/ 1
43
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:32: 2
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-OP-L
Licensed To: B & W ID: 13709
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 10 159.32 268.89 59.2 20 159.32 268.89 59.2
2 (OPE) 10 159.32 268.89 59.2 20 159.32 268.89 59.2
3 (OPE) 10 159.32 268.89 59.2 20 159.32 268.89 59.2
4 (OPE) 10 159.32 268.89 59.2 20 159.32 268.89 59.2
5 (OPE) 10 159.32 268.89 59.2 20 159.32 268.89 59.2
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (OPE) 20 159.32 268.89 59.2 30 159.32 268.89 59.2
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 80 159.32 268.89 59.2 90 159.32 268.89 59.2
2 (OPE) 80 159.32 268.89 59.2 90 159.32 268.89 59.2
3 (OPE) 80 159.32 268.89 59.2 90 159.32 268.89 59.2
4 (OPE) 80 159.32 268.89 59.2 90 159.32 268.89 59.2
5 (OPE) 80 159.32 268.89 59.2 90 159.32 268.89 59.2
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 130 158.93 268.89 59.1 140 158.50 268.89 58.9
4 (OPE) 130 158.93 268.89 59.1 140 158.50 268.89 58.9
5 (OPE) 130 158.93 268.89 59.1 140 158.50 268.89 58.9
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (OPE) 180 157.34 268.89 58.5 190 156.91 268.89 58.4
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 240 155.55 268.89 57.8 250 155.55 268.89 57.8
2 (OPE) 240 155.55 268.89 57.8 250 155.55 268.89 57.8
3 (OPE) 240 155.55 268.89 57.8 250 155.55 268.89 57.8
4 (OPE) 240 155.55 268.89 57.8 250 155.55 268.89 57.8
5 (OPE) 240 155.55 268.89 57.8 250 155.55 268.89 57.8
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 280 155.42 268.89 57.8 290 155.42 268.89 57.8
4 (OPE) 280 155.42 268.89 57.8 290 155.42 268.89 57.8
5 (OPE) 280 155.42 268.89 57.8 290 155.42 268.89 57.8
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (OPE) 330 155.42 268.89 57.8 340 155.42 268.89 57.8
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 380 155.42 268.89 57.8 381 155.42 268.89 57.8
2 (OPE) 380 155.42 268.89 57.8 381 155.42 268.89 57.8
3 (OPE) 380 155.42 268.89 57.8 381 155.42 268.89 57.8
4 (OPE) 380 155.42 268.89 57.8 381 155.42 268.89 57.8
5 (OPE) 380 155.42 268.89 57.8 381 155.42 268.89 57.8
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 390 0.00 0.00 0.0 400 0.00 0.00 0.0
4 (OPE) 390 0.00 0.00 0.0 400 0.00 0.00 0.0
5 (OPE) 390 0.00 0.00 0.0 400 0.00 0.00 0.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (OPE) 440 155.42 268.89 57.8 450 155.42 268.89 57.8
Table of Contents
INPUT LISTING .................................................................................................................................................... 2
MISCELLANEOUS COMPUTED DATA ..................................................................................................................... 17
Displacements 1 (HYD) W+D5+T1+HP....................................................................................................... 25
Displacements 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1............................................................................ 27
Displacements 3 (HYD) W+D2+D5+T1+HP+WIN2+WAV2............................................................................ 29
Displacements 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3............................................................................ 31
Displacements 5 (HYD) W+D4+D5+T1+HP+WIN4+WAV4............................................................................ 33
Restraint Summary 1 (HYD) W+D5+T1+HP 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1 3 (HYD)
W+D2+D5+T1+HP+WIN2+WAV2 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3 5 (HYD)
W+D4+D5+T1+HP+WIN4+WAV4.............................................................................................................................. 35
Stresses 1 (HYD) W+D5+T1+HP................................................................................................................ 41
Stresses 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1..................................................................................... 45
Stresses 3 (HYD) W+D2+D5+T1+HP+WIN2+WAV2..................................................................................... 49
Stresses 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3..................................................................................... 53
Stresses 5 (HYD) W+D4+D5+T1+HP+WIN4+WAV4..................................................................................... 57
Code Compliance Extended 1 (HYD) W+D5+T1+HP 2 (HYD) W+D1+D5+T1+HP+WIN1+WAV1 3
(HYD) W+D2+D5+T1+HP+WIN2+WAV2 4 (HYD) W+D3+D5+T1+HP+WIN3+WAV3 5 (HYD)
W+D4+D5+T1+HP+WIN4+WAV4 61
2
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
Job Description:
ANALYST: SV
PIPE DATA
-----------------------------------------------------------------------------
-----------------------------------------------------------------------------
From 10 To 20 DX= 5,000.000 mm.
PIPE
Dia= 406.400 mm. Wall= 23.800 mm. Insul= .450 mm.
GENERAL
T1= 29 C PHyd= 382.8000 bars Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m. Insul= 1,440.0000 kg/cu.m.
Fluid=1025.0000000 kg/cu.m.
RESTRAINTS
Node 10 ANC Cnode 1000
DISPLACEMENTS
Node 1000 DX1= 10.300 mm. DY1= -30.300 mm. DZ1= 1.800 mm.
DX2= -111.700 mm. DY2= -32.500 mm. DZ2= -.600 mm. DX3= -25.500 mm.
DY3= -30.400 mm. DZ3= 25.900 mm. DX4= -26.100 mm. DY4= -30.900 mm.
DZ4= -45.600 mm.
WIND
Wind Shape= .500
ALLOWABLE STRESSES
B31.4 IX (2002) Sy= 448 N./sq.mm. Fac= .6000
-----------------------------------------------------------------------------
From 20 To 30 DX= 3,500.000 mm.
BEND at "TO" end
Radius= 2,032.000 mm. (user) Bend Angle= 90.000
-----------------------------------------------------------------------------
From 30 To 40 DY= -4,500.000 mm.
BEND at "TO" end
Radius= 2,032.000 mm. (user) Bend Angle= 5.711
-----------------------------------------------------------------------------
From 40 To 50 DX= 218.100 mm. DY= -2,181.000 mm.
-----------------------------------------------------------------------------
From 50 To 60 DX= 31.900 mm. DY= -319.000 mm.
RIGID Weight= 5,564.45 N.
-----------------------------------------------------------------------------
From 60 To 70 DX= 31.900 mm. DY= -319.000 mm.
RIGID Weight= 5,564.45 N.
-----------------------------------------------------------------------------
From 70 To 80 DX= 118.100 mm. DY= -1,181.000 mm.
RESTRAINTS
Node 80 X Cnode 800 Dir Vec= .9950 .0995 .0000
Node 80 Z Cnode 800
Node 80 +Y Cnode 800
DISPLACEMENTS
Node 800 DX1= 8.300 mm. DY1= -30.600 mm. DZ1= 1.600 mm.
3
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
DX2= -107.100 mm. DY2= -32.200 mm. DZ2= .400 mm. DX3= -25.000 mm.
DY3= -30.500 mm. DZ3= 24.900 mm. DX4= -26.200 mm. DY4= -31.100 mm.
DZ4= -43.300 mm.
-----------------------------------------------------------------------------
From 80 To 90 DX= 500.000 mm. DY= -5,000.000 mm.
-----------------------------------------------------------------------------
From 90 To 100 DX= 100.000 mm. DY= -1,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 100 To 110 DX= 100.000 mm. DY= -1,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 110 To 120 DX= 90.000 mm. DY= -900.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 120 To 130 DX= 160.000 mm. DY= -1,600.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 130 To 140 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 140 To 150 DX= 350.000 mm. DY= -3,500.000 mm.
GENERAL
RESTRAINTS
Node 150 X Cnode 1500 Dir Vec= .9950 .0995 .0000
Node 150 Z Cnode 1500
DISPLACEMENTS
Node 1500 DX1= 4.000 mm. DY1= -31.300 mm. DZ1= 1.200 mm.
DX2= -97.400 mm. DY2= -31.500 mm. DZ2= 2.600 mm. DX3= -23.900 mm.
DY3= -30.700 mm. DZ3= 22.700 mm. DX4= -26.400 mm. DY4= -31.500 mm.
DZ4= -38.500 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 150 To 160 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 160 To 170 DX= 230.000 mm. DY= -2,300.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 170 To 180 DX= 270.000 mm. DY= -2,700.000 mm.
4
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 180 To 190 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
RESTRAINTS
Node 190 X Cnode 1900 Dir Vec= .9950 .0995 .0000
Node 190 Z Cnode 1900
DISPLACEMENTS
Node 1900 DX1= -2.400 mm. DY1= -31.700 mm. DZ1= -.200 mm.
DX2= -74.100 mm. DY2= -29.300 mm. DZ2= -1.000 mm. DX3= -21.600 mm.
DY3= -30.600 mm. DZ3= 14.800 mm. DX4= -23.600 mm. DY4= -31.300 mm.
DZ4= -30.000 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 190 To 200 DX= 500.000 mm. DY= -5,000.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 200 To 210 DX= 350.000 mm. DY= -3,500.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 210 To 220 DX= 190.000 mm. DY= -1,900.000 mm.
GENERAL
RESTRAINTS
Node 220 X Cnode 2200 Dir Vec= .9950 .0995 .0000
Node 220 Z Cnode 2200
DISPLACEMENTS
Node 2200 DX1= -6.800 mm. DY1= -32.000 mm. DZ1= -1.200 mm.
DX2= -58.000 mm. DY2= -27.800 mm. DZ2= -3.500 mm. DX3= -20.000 mm.
DY3= -30.500 mm. DZ3= 9.300 mm. DX4= -21.700 mm. DY4= -31.200 mm.
DZ4= -24.100 mm.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 220 To 230 DX= 336.400 mm. DY= -3,364.000 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 230 To 240 DX= 208.800 mm. DY= -2,088.000 mm.
PIPE
Dia= 406.400 mm. Wall= 22.860 mm. Insul= .450 mm.
GENERAL
BEND at "TO" end
Radius= 2,032.000 mm. (user) Bend Angle= 84.745
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 240 To 250 DX= 2,635.400 mm. DZ= 1,118.700 mm.
5
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
PIPE
Dia= 406.400 mm. Wall= 23.800 mm. Insul= .450 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 250 To 260 DX= 295.500 mm. DZ= 125.400 mm.
PIPE
Dia= 406.400 mm. Wall= 23.800 mm. Insul= .450 mm.
GENERAL
RIGID Weight= 5,564.45 N.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 260 To 270 DX= 295.500 mm. DZ= 125.400 mm.
GENERAL
RIGID Weight= 5,564.45 N.
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 270 To 271 DX= 1,531.700 mm. DZ= 650.200 mm.
PIPE
Dia= 406.400 mm. Wall= 22.860 mm. Insul= .450 mm.
GENERAL
BEND at "TO" end
Radius= 2,032.000 mm. (user) Bend Angle= 29.999
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 271 To 280 DX= 2,462.400 mm. DY= -1,544.400 mm. DZ= 1,045.200 mm.
GENERAL
BEND at "TO" end
Radius= 2,032.000 mm. (user) Bend Angle= 29.999
WAVE
Drag Coef= .700 Added Mass Coef= 1.290 Lift Coef= .001
-----------------------------------------------------------------------------
From 280 To 290 DX= 2,301.300 mm. DZ= 976.800 mm.
PIPE
Dia= 406.400 mm. Wall= 23.800 mm. Insul= .450 mm.
GENERAL
RESTRAINTS
Node 290 +Y K= 183 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 290 To 300 DX= 4,602.500 mm. DZ= 1,953.700 mm.
GENERAL
RESTRAINTS
Node 300 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 300 To 310 DX= 4,602.500 mm. DZ= 1,953.700 mm.
GENERAL
RESTRAINTS
6
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
PIPE
Dia= 406.400 mm. Wall= 23.800 mm. Insul= .450 mm.
GENERAL
RESTRAINTS
Node 380 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 380 To 381 DX= -466.900 mm. DZ= 1,944.700 mm.
GENERAL
RESTRAINTS
Node 381 +Y K= 146 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
SIF's & TEE's
Node 381 Welding Tee
-----------------------------------------------------------------------------
From 381 To 505 DX= 782.800 mm. DZ= 187.900 mm.
GENERAL
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 505 To 506 DX= 311.818 mm. DZ= 74.848 mm.
GENERAL
RIGID Weight= 5,564.45 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 381 To 382 DX= -1,139.000 mm. DZ= 4,744.200 mm.
GENERAL
RESTRAINTS
Node 382 +Y K= 380 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 382 To 390 DX= -74.805 mm. DZ= 311.828 mm.
GENERAL
RIGID Weight= 5,564.45 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 390 To 400 DX= -74.805 mm. DZ= 311.828 mm.
GENERAL
RIGID Weight= 5,564.45 N.
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 400 To 410 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
Node 410 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 410 To 420 DX= -1,167.200 mm. DZ= 4,861.800 mm.
8
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
GENERAL
RESTRAINTS
Node 420 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 420 To 430 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
Node 430 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 430 To 440 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
Node 440 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 440 To 450 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
Node 450 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 450 To 460 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
Node 460 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 460 To 470 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
Node 470 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 470 To 480 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
Node 480 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 480 To 490 DX= -1,167.200 mm. DZ= 4,861.800 mm.
GENERAL
RESTRAINTS
Node 490 +Y K= 365 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
9
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
MATERIAL Changes:
10 20 Mat= (306)API-5L X65 E= 207,000 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m.
JOBNAME: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
BEND ELEMENTS
20 30 Radius= 2,032.000 mm. (user)
Bend Angle= 90.000
30 40 Radius= 2,032.000 mm. (user)
Bend Angle= 5.711
230 240 Radius= 2,032.000 mm. (user)
Bend Angle= 84.745
270 271 Radius= 2,032.000 mm. (user)
Bend Angle= 29.999
271 280 Radius= 2,032.000 mm. (user)
Bend Angle= 29.999
360 370 Radius= 2,032.000 mm. (user)
Bend Angle= 80.501
RIGIDS
50 60 RIGID Weight= 5,564.45 N.
60 70 RIGID Weight= 5,564.45 N.
250 260 RIGID Weight= 5,564.45 N.
260 270 RIGID Weight= 5,564.45 N.
505 506 RIGID Weight= 5,564.45 N.
382 390 RIGID Weight= 5,564.45 N.
390 400 RIGID Weight= 5,564.45 N.
RESTRAINTS Len MU
GAP YIELD Dir
NODE TYPE CNODE STIF1 STIF2 FORCE Vectors
-------+-------+------+----------+----------+----------+---------------------
10 ANC 1000 .000 .000 .000
80 X 800 .995 .100 .000
10
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
DISPLACEMENTS
10 20 Node 1000 DX1= 10.300 mm. DY1= -30.300 mm.
DZ1= 1.800 mm. DX2= -111.700 mm.
DY2= -32.500 mm. DZ2= -.600 mm.
DX3= -25.500 mm. DY3= -30.400 mm.
DZ3= 25.900 mm. DX4= -26.100 mm.
DY4= -30.900 mm. DZ4= -45.600 mm.
70 80 Node 800 DX1= 8.300 mm. DY1= -30.600 mm.
DZ1= 1.600 mm. DX2= -107.100 mm.
DY2= -32.200 mm. DZ2= .400 mm.
DX3= -25.000 mm. DY3= -30.500 mm.
DZ3= 24.900 mm. DX4= -26.200 mm.
DY4= -31.100 mm. DZ4= -43.300 mm.
140 150 Node 1500 DX1= 4.000 mm. DY1= -31.300 mm.
DZ1= 1.200 mm. DX2= -97.400 mm.
DY2= -31.500 mm. DZ2= 2.600 mm.
DX3= -23.900 mm. DY3= -30.700 mm.
DZ3= 22.700 mm. DX4= -26.400 mm.
DY4= -31.500 mm. DZ4= -38.500 mm.
180 190 Node 1900 DX1= -2.400 mm. DY1= -31.700 mm.
DZ1= -.200 mm. DX2= -74.100 mm.
11
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
WIND/WAVE
10 20 WIND Wind Shape= .500
90 100 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
100 110 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
110 120 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
120 130 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
130 140 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
140 150 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
150 160 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
160 170 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
170 180 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
180 190 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
190 200 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
200 210 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
210 220 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
220 230 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
230 240 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
240 250 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
250 260 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
260 270 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
270 271 WAVE Drag Coef= .700
Added Mass Coef= 1.290 Lift Coef= .001
12
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
COORDINATE REPORT
/--------------------(mm.)----------------------/
NODE X Y Z
10 .0000 13500.0000 .0000
20 5000.0000 13500.0000 .0000
30 8500.0000 13500.0000 .0000
40 8500.0000 9000.0000 .0000
50 8718.0996 6819.0000 .0000
60 8750.0000 6500.0000 .0000
70 8781.9004 6181.0000 .0000
80 8900.0000 5000.0000 .0000
90 9400.0000 .0000 .0000
100 9500.0000 -1000.0000 .0000
110 9600.0000 -2000.0000 .0000
120 9690.0000 -2900.0000 .0000
130 9850.0000 -4500.0000 .0000
140 10350.0000 -9500.0000 .0000
150 10700.0000 -13000.0000 .0000
160 11200.0000 -18000.0000 .0000
170 11430.0000 -20300.0000 .0000
180 11700.0000 -23000.0000 .0000
190 12200.0000 -28000.0000 .0000
200 12700.0000 -33000.0000 .0000
210 13050.0000 -36500.0000 .0000
220 13240.0000 -38400.0000 .0000
230 13576.4004 -41764.0000 .0000
240 13785.2002 -43852.0000 .0000
250 16420.5996 -43852.0000 1118.7000
260 16716.0996 -43852.0000 1244.1000
270 17011.5996 -43852.0000 1369.5000
271 18543.2988 -43852.0000 2019.7000
280 21005.6992 -45396.3984 3064.8999
290 23307.0000 -45396.3984 4041.7000
300 27909.5000 -45396.3984 5995.3999
310 32512.0000 -45396.3984 7949.0996
320 37114.5000 -45396.3984 9902.7998
330 41717.0000 -45396.3984 11856.5000
340 46319.5000 -45396.3984 13810.2002
341 47608.1992 -45396.3984 14357.2002
350 52210.6992 -45396.3984 16310.9004
360 55892.6992 -45396.3984 17873.8008
370 58194.0000 -45396.3984 18850.6016
380 57026.8008 -45396.3984 23712.4023
381 56559.9023 -45396.3984 25657.1016
505 57342.7031 -45396.3984 25845.0020
506 57654.5195 -45396.3984 25919.8496
381 56559.9023 -45396.3984 25657.1016
382 55420.9023 -45396.3984 30401.3008
390 55346.0977 -45396.3984 30713.1289
400 55271.2930 -45396.3984 31024.9570
16
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
BEND DATA:
10 20
TYPE KEY:
3 - Welding Tee
4 - Sweepolet
5 - Weldolet
10. 20. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
20. 30. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
30. 40. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
18
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
40. 50. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
50. 60. 17.357 0.014 1.016 0.000E+00 0.000E+00 0.000E+00 NA NA
60. 70. 17.357 0.014 1.016 0.000E+00 0.000E+00 0.000E+00 NA NA
70. 80. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
80. 90. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
90. 100. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
100. 110. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
110. 120. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
120. 130. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
130. 140. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
140. 150. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
150. 160. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
160. 170. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
170. 180. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
180. 190. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
190. 200. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
200. 210. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
210. 220. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
220. 230. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
230. 240. 2.120 0.008 1.027 0.000E+00 0.000E+00 0.000E+00 .000 .000
240. 250. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
250. 260. 17.334 0.014 1.016 0.000E+00 0.000E+00 0.000E+00 NA NA
260. 270. 17.334 0.014 1.016 0.000E+00 0.000E+00 0.000E+00 NA NA
270. 271. 2.120 0.008 1.027 0.000E+00 0.000E+00 0.000E+00 .000 .000
271. 280. 2.120 0.008 1.027 0.000E+00 0.000E+00 0.000E+00 .000 .000
280. 290. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
290. 300. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
300. 310. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
310. 320. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
320. 330. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
330. 340. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
340. 341. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
341. 350. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
350. 360. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
360. 370. 2.120 0.008 1.027 0.000E+00 0.000E+00 0.000E+00 .000 .000
370. 380. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
380. 381. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
381. 505. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
505. 506. 17.352 0.014 1.016 0.000E+00 0.000E+00 0.000E+00 NA NA
381. 382. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
382. 390. 17.352 0.014 1.016 0.000E+00 0.000E+00 0.000E+00 NA NA
390. 400. 17.352 0.014 1.016 0.000E+00 0.000E+00 0.000E+00 NA NA
400. 410. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
410. 420. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
420. 430. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
430. 440. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
440. 450. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
450. 460. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
460. 470. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
470. 480. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
480. 490. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
490. 500. 2.202 0.008 1.016 0.000E+00 0.000E+00 0.000E+00 .000 .000
10. 20. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
20. 30. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
30. 40. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
40. 50. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
50. 60. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
60. 70. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
70. 80. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
80. 90. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
90. 100. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
100. 110. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
110. 120. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
120. 130. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
130. 140. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
140. 150. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
150. 160. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
160. 170. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
170. 180. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
180. 190. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
190. 200. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
200. 210. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
210. 220. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
220. 230. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
230. 240. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
240. 250. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
250. 260. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
260. 270. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
270. 271. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
271. 280. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
280. 290. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
290. 300. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
300. 310. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
310. 320. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
320. 330. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
330. 340. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
340. 341. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
341. 350. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
350. 360. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
360. 370. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
370. 380. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
380. 381. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
381. 505. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
505. 506. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
381. 382. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
382. 390. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
390. 400. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
400. 410. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
410. 420. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
420. 430. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
430. 440. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
440. 450. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
450. 460. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
20
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
460. 470. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
470. 480. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
480. 490. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
490. 500. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
WIND LOADING #: 1
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... 1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 2
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ........... -1.0000
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ...........
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 3
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... 1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
Structure Natural Frequency ................(Hz.) 0.0000
----/ ASCE#7 TOPOGRAPHIC FACTOR PARAMETERS /-----
Height of Hill or Escarpment .................... 0.0000 mm.
Crest Distance .................................. 0.0000 mm.
Distance from Crest to Site...................... 0.0000 mm.
HILL TYPE (0,1,2 or 3) .......................... 0
WIND LOADING #: 4
ASCE#7-95 STANDARD FOR WIND LOADING
-----/ WIND DIRECTION SPECIFICATION /------------
X WIND Direction cosine (or vector) ...........
Y WIND Direction cosine (or vector) ...........
Z WIND Direction cosine (or vector) ........... -1.0000
---------/ ASCE#7 WIND LOAD PARAMETERS /---------
Basic Wind Speed ................................ 32000.0000 mm./sec.
Wind Exposure (1,2,3 or 4) ...................... 3
Structural Damping Coef. (TYP=0.03) ............. 0.0300
Structural Classification (1,2,3 or 4) .......... 2
(or) Importance Factor........................... 1.0000
22
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
WAVE VECTOR 1
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and 1.000 0.000
Wave Theory STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1100.000
2 22800.000 800.000
3 45600.000 300.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 2
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and -1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
23
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
WAVE VECTOR 3
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and 0.000 1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45600.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 0.000 1.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1100.000
2 22800.000 800.000
3 45600.000 300.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 4
Velocity Units : mm./sec.
24
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
Rigid X;
80 Rigid Z;
Rigid +Y
1 (HYD) 15178 -174206 223 0 0 0
2 (HYD) 27800 -172352 150 0 0 0
3 (HYD) 2028 -176957 254 0 0 0
4 (HYD) 14128 -172798 8498 0 0 0
5 (HYD) 14294 -174604 -8116 0 0 0
MAX 27800/ 2 176957/ 3 8498/ 4 0/ 1 0/ 1 0/ 1
Rigid X;
150
Rigid Z
1 (HYD) -4577 -458 -189 0 0 0
2 (HYD) 8308 831 -31 0 0 0
3 (HYD) -12103 -1210 -208 0 0 0
4 (HYD) -4223 -422 10557 0 0 0
5 (HYD) -3805 -381 -10446 0 0 0
MAX 12103/ 3 1210/ 3 10557/ 4 0/ 1 0/ 1 0/ 1
Rigid X;
190
Rigid Z
1 (HYD) 2447 245 523 0 0 0
2 (HYD) -262 -26 -623 0 0 0
3 (HYD) -6778 -678 -2174 0 0 0
4 (HYD) -1568 -157 719 0 0 0
5 (HYD) -2920 -292 -3623 0 0 0
MAX 6778/ 3 678/ 3 3623/ 5 0/ 1 0/ 1 0/ 1
Rigid X;
220
Rigid Z
1 (HYD) -4167 -417 2420 0 0 0
2 (HYD) 2927 293 4037 0 0 0
3 (HYD) 14336 1434 11124 0 0 0
36
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
290 Flex +Y
1 (HYD) -3919 -5687 701 0 0 0
2 (HYD) -5298 -7718 1057 0 0 0
3 (HYD) -4056 -5797 -116 0 0 0
4 (HYD) -5064 -7443 1226 0 0 0
5 (HYD) -4725 -6834 -745 0 0 0
MAX 5298/ 2 7718/ 2 1226/ 4 0/ 1 0/ 1 0/ 1
300 Flex +Y
1 (HYD) -8126 -11681 912 0 0 0
2 (HYD) -9109 -13115 1143 0 0 0
3 (HYD) -7504 -10810 -974 0 0 0
4 (HYD) -9025 -12946 814 0 0 0
5 (HYD) -8235 -11929 -1385 0 0 0
MAX 9109/ 2 13115/ 2 1385/ 5 0/ 1 0/ 1 0/ 1
310 Flex +Y
1 (HYD) -6729 -10938 -3654 0 0 0
2 (HYD) -6376 -11000 -4316 0 0 0
3 (HYD) -6514 -10051 -2659 0 0 0
4 (HYD) -7060 -11096 -3239 0 0 0
5 (HYD) -6323 -10371 -3567 0 0 0
MAX 7060/ 4 11096/ 4 4316/ 2 0/ 1 0/ 1 0/ 1
320 Flex +Y
1 (HYD) -451 -10056 -7025 0 0 0
2 (HYD) 245 -9646 -6748 0 0 0
3 (HYD) -4206 -9502 -5153 0 0 0
4 (HYD) -1450 -9874 -6758 0 0 0
5 (HYD) -2340 -9362 -6121 0 0 0
MAX 4206/ 3 10056/ 1 7025/ 1 0/ 1 0/ 1 0/ 1
330 Flex +Y
1 (HYD) 1509 -9416 -6417 0 0 0
2 (HYD) 1692 -8995 -6065 0 0 0
3 (HYD) -1262 -9187 -6306 0 0 0
4 (HYD) 1060 -9263 -6397 0 0 0
5 (HYD) 326 -8865 -6197 0 0 0
MAX 1692/ 2 9416/ 1 6417/ 1 0/ 1 0/ 1 0/ 1
340 Flex +Y
1 (HYD) 2006 -9190 -6112 0 0 0
2 (HYD) 2070 -8902 -5878 0 0 0
3 (HYD) 406 -9164 -6402 0 0 0
4 (HYD) 1787 -9165 -6161 0 0 0
37
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
341 Flex +Y
1 (HYD) 584 -2580 -1709 0 0 0
2 (HYD) 600 -2511 -1652 0 0 0
3 (HYD) 194 -2583 -1798 0 0 0
4 (HYD) 533 -2583 -1727 0 0 0
5 (HYD) 414 -2491 -1694 0 0 0
MAX 600/ 2 2583/ 3 1798/ 3 0/ 1 0/ 1 0/ 1
350 Flex +Y
1 (HYD) 2366 -9696 -6362 0 0 0
2 (HYD) 2410 -9558 -6242 0 0 0
3 (HYD) 1407 -9776 -6697 0 0 0
4 (HYD) 2263 -9787 -6467 0 0 0
5 (HYD) 1942 -9529 -6381 0 0 0
MAX 2410/ 2 9787/ 4 6697/ 3 0/ 1 0/ 1 0/ 1
360 Flex +Y
1 (HYD) 2119 -8441 -5516 0 0 0
2 (HYD) 2155 -8373 -5450 0 0 0
3 (HYD) 1467 -8519 -5780 0 0 0
4 (HYD) 2057 -8534 -5609 0 0 0
5 (HYD) 1840 -8398 -5583 0 0 0
MAX 2155/ 2 8534/ 4 5780/ 3 0/ 1 0/ 1 0/ 1
370 Flex +Y
1 (HYD) 1712 -5968 -3811 0 0 0
2 (HYD) 1740 -5927 -3767 0 0 0
3 (HYD) 1325 -6039 -4014 0 0 0
4 (HYD) 1681 -6030 -3872 0 0 0
5 (HYD) 1548 -5963 -3877 0 0 0
MAX 1740/ 2 6039/ 3 4014/ 3 0/ 1 0/ 1 0/ 1
380 Flex +Y
1 (HYD) 4202 -13000 -8072 0 0 0
2 (HYD) 4274 -12876 -7936 0 0 0
3 (HYD) 3471 -13192 -8558 0 0 0
4 (HYD) 4153 -13107 -8181 0 0 0
5 (HYD) 3889 -12960 -8196 0 0 0
MAX 4274/ 2 13192/ 3 8558/ 3 0/ 1 0/ 1 0/ 1
381 Flex +Y
1 (HYD) 1825 -5454 -3353 0 0 0
2 (HYD) 1857 -5395 -3288 0 0 0
3 (HYD) 1543 -5540 -3558 0 0 0
4 (HYD) 1807 -5490 -3392 0 0 0
5 (HYD) 1706 -5436 -3401 0 0 0
38
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
382 Flex +Y
1 (HYD) 4981 -14704 -9007 0 0 0
2 (HYD) 5085 -14506 -8789 0 0 0
3 (HYD) 4349 -14953 -9521 0 0 0
4 (HYD) 4944 -14754 -9068 0 0 0
5 (HYD) 4738 -14668 -9109 0 0 0
MAX 5085/ 2 14953/ 3 9521/ 3 0/ 1 0/ 1 0/ 1
410 Flex +Y
1 (HYD) 4124 -12858 -8000 0 0 0
2 (HYD) 4233 -12644 -7773 0 0 0
3 (HYD) 3672 -13101 -8404 0 0 0
4 (HYD) 4103 -12869 -8020 0 0 0
5 (HYD) 3982 -12849 -8065 0 0 0
MAX 4233/ 2 13101/ 3 8404/ 3 0/ 1 0/ 1 0/ 1
420 Flex +Y
1 (HYD) 3317 -11300 -7181 0 0 0
2 (HYD) 3431 -11080 -6956 0 0 0
3 (HYD) 2983 -11535 -7504 0 0 0
4 (HYD) 3308 -11293 -7180 0 0 0
5 (HYD) 3238 -11307 -7222 0 0 0
MAX 3431/ 2 11535/ 3 7504/ 3 0/ 1 0/ 1 0/ 1
430 Flex +Y
1 (HYD) 2703 -10268 -6660 0 0 0
2 (HYD) 2826 -10049 -6441 0 0 0
3 (HYD) 2447 -10498 -6929 0 0 0
4 (HYD) 2703 -10256 -6651 0 0 0
5 (HYD) 2665 -10285 -6688 0 0 0
MAX 2826/ 2 10498/ 3 6929/ 3 0/ 1 0/ 1 0/ 1
440 Flex +Y
1 (HYD) 2319 -9883 -6518 0 0 0
2 (HYD) 2456 -9663 -6302 0 0 0
3 (HYD) 2112 -10111 -6755 0 0 0
4 (HYD) 2327 -9870 -6506 0 0 0
5 (HYD) 2304 -9903 -6538 0 0 0
MAX 2456/ 2 10111/ 3 6755/ 3 0/ 1 0/ 1 0/ 1
450 Flex +Y
1 (HYD) 2092 -9930 -6629 0 0 0
2 (HYD) 2241 -9709 -6416 0 0 0
3 (HYD) 1918 -10161 -6849 0 0 0
4 (HYD) 2104 -9919 -6617 0 0 0
5 (HYD) 2091 -9951 -6645 0 0 0
MAX 2241/ 2 10161/ 3 6849/ 3 0/ 1 0/ 1 0/ 1
39
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
460 Flex +Y
1 (HYD) 1933 -10045 -6760 0 0 0
2 (HYD) 2083 -9824 -6553 0 0 0
3 (HYD) 1791 -10276 -6967 0 0 0
4 (HYD) 1947 -10035 -6750 0 0 0
5 (HYD) 1938 -10065 -6773 0 0 0
MAX 2083/ 2 10276/ 3 6967/ 3 0/ 1 0/ 1 0/ 1
470 Flex +Y
1 (HYD) 1745 -9709 -6568 0 0 0
2 (HYD) 1873 -9500 -6380 0 0 0
3 (HYD) 1642 -9929 -6753 0 0 0
4 (HYD) 1757 -9702 -6560 0 0 0
5 (HYD) 1753 -9727 -6580 0 0 0
MAX 1873/ 2 9929/ 3 6753/ 3 0/ 1 0/ 1 0/ 1
480 Flex +Y
1 (HYD) 1416 -8245 -5595 0 0 0
2 (HYD) 1493 -8072 -5449 0 0 0
3 (HYD) 1361 -8428 -5740 0 0 0
4 (HYD) 1423 -8239 -5589 0 0 0
5 (HYD) 1422 -8260 -5605 0 0 0
MAX 1493/ 2 8428/ 3 5740/ 3 0/ 1 0/ 1 0/ 1
490 Flex +Y
1 (HYD) 834 -4999 -3399 0 0 0
2 (HYD) 852 -4897 -3320 0 0 0
3 (HYD) 824 -5107 -3478 0 0 0
4 (HYD) 836 -4996 -3396 0 0 0
5 (HYD) 836 -5008 -3404 0 0 0
MAX 852/ 2 5107/ 3 3478/ 3 0/ 1 0/ 1 0/ 1
Displ.
800
Reaction
1 (HYD) 15178 -174206 223 0 0 0
2 (HYD) 27800 -172352 150 0 0 0
3 (HYD) 2028 -176956 254 0 0 0
4 (HYD) 14128 -172797 8498 0 0 0
5 (HYD) 14294 -174604 -8116 0 0 0
MAX 27800/ 2 176956/ 3 8498/ 4 0/ 1 0/ 1 0/ 1
40
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
Displ.
1000
Reaction
1 (HYD) -4719 -10858 -128 0 0 0
2 (HYD) -8112 -9657 -70 0 0 0
3 (HYD) -254 -12908 -61 0 0 0
4 (HYD) -4228 -11104 718 0 0 0
5 (HYD) -4331 -10961 -949 0 0 0
MAX 8112/ 2 12908/ 3 949/ 5 0/ 1 0/ 1 0/ 1
Displ.
1500
Reaction
1 (HYD) -4577 -458 -189 0 0 0
2 (HYD) 8308 831 -31 0 0 0
3 (HYD) -12103 -1210 -208 0 0 0
4 (HYD) -4223 -422 10557 0 0 0
5 (HYD) -3805 -381 -10446 0 0 0
MAX 12103/ 3 1210/ 3 10557/ 4 0/ 1 0/ 1 0/ 1
Displ.
1900
Reaction
1 (HYD) 2447 245 523 0 0 0
2 (HYD) -262 -26 -623 0 0 0
3 (HYD) -6778 -678 -2174 0 0 0
4 (HYD) -1568 -157 719 0 0 0
5 (HYD) -2920 -292 -3623 0 0 0
MAX 6778/ 3 678/ 3 3623/ 5 0/ 1 0/ 1 0/ 1
Displ.
2200
Reaction
1 (HYD) -4167 -417 2420 0 0 0
2 (HYD) 2927 293 4037 0 0 0
3 (HYD) 14336 1434 11124 0 0 0
4 (HYD) 2898 290 5549 0 0 0
5 (HYD) 7611 761 7904 0 0 0
MAX 14336/ 3 1434/ 3 11124/ 3 0/ 1 0/ 1 0/ 1
Displ.
5000
Reaction
1 (HYD) -26188 -8919 106445 0 0 0
2 (HYD) -25942 -8707 107627 0 0 0
3 (HYD) -27624 -9142 111207 0 0 0
4 (HYD) -26266 -8912 106931 0 0 0
5 (HYD) -25807 -8937 104964 0 0 0
MAX 27624/ 3 9142/ 3 111207/ 3 0/ 1 0/ 1 0/ 1
41
C A E S A R I I VER.5.00.7, (Build 070122) APR 18,2007 17:51:16
Jobname: D:\SAKTHI\CAESAR\STD\16LINE\LATERAL\3 BEND CONFN\RISER16-HYD
Licensed To: B & W ID: 13709
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 10 326.83 403.33 81.0 20 326.83 403.33 81.0
2 (HYD) 10 326.83 403.33 81.0 20 326.83 403.33 81.0
3 (HYD) 10 326.83 403.33 81.0 20 326.83 403.33 81.0
4 (HYD) 10 326.83 403.33 81.0 20 326.83 403.33 81.0
5 (HYD) 10 326.83 403.33 81.0 20 326.83 403.33 81.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (HYD) 20 326.83 403.33 81.0 30 326.83 403.33 81.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 80 326.83 403.33 81.0 90 326.83 403.33 81.0
2 (HYD) 80 326.83 403.33 81.0 90 326.83 403.33 81.0
3 (HYD) 80 326.83 403.33 81.0 90 326.83 403.33 81.0
4 (HYD) 80 326.83 403.33 81.0 90 326.83 403.33 81.0
5 (HYD) 80 326.83 403.33 81.0 90 326.83 403.33 81.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 130 326.44 403.33 80.9 140 326.01 403.33 80.8
4 (HYD) 130 326.44 403.33 80.9 140 326.01 403.33 80.8
5 (HYD) 130 326.44 403.33 80.9 140 326.01 403.33 80.8
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (HYD) 180 324.85 403.33 80.5 190 324.42 403.33 80.4
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 240 323.06 403.33 80.1 250 323.06 403.33 80.1
2 (HYD) 240 323.06 403.33 80.1 250 323.06 403.33 80.1
3 (HYD) 240 323.06 403.33 80.1 250 323.06 403.33 80.1
4 (HYD) 240 323.06 403.33 80.1 250 323.06 403.33 80.1
5 (HYD) 240 323.06 403.33 80.1 250 323.06 403.33 80.1
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 280 322.93 403.33 80.1 290 322.93 403.33 80.1
4 (HYD) 280 322.93 403.33 80.1 290 322.93 403.33 80.1
5 (HYD) 280 322.93 403.33 80.1 290 322.93 403.33 80.1
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (HYD) 330 322.93 403.33 80.1 340 322.93 403.33 80.1
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 380 322.93 403.33 80.1 381 322.93 403.33 80.1
2 (HYD) 380 322.93 403.33 80.1 381 322.93 403.33 80.1
3 (HYD) 380 322.93 403.33 80.1 381 322.93 403.33 80.1
4 (HYD) 380 322.93 403.33 80.1 381 322.93 403.33 80.1
5 (HYD) 380 322.93 403.33 80.1 381 322.93 403.33 80.1
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 390 0.00 0.00 0.0 400 0.00 0.00 0.0
4 (HYD) 390 0.00 0.00 0.0 400 0.00 0.00 0.0
5 (HYD) 390 0.00 0.00 0.0 400 0.00 0.00 0.0
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
5 (HYD) 440 322.93 403.33 80.1 450 322.93 403.33 80.1
CAESAR II
LOAD CONDITION DESCRIPTION
RUN
OPERATION + 100 YEAR
OPERATION 1
ENVIRONMENTAL LOAD
HYDROTEST + 1 YEAR
HYDROTEST 2
ENVIRONMENTAL LOAD
2005-6031-2J-0010 Rev.C – Riser and Subsea Tie-in Spool Analysis Report Page 49 of 49
1
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
Table of Contents
INPUT LISTING .................................................................................................................................................... 2
MISCELLANEOUS COMPUTED DATA ..................................................................................................................... 18
Displacements 1 (OPE) W+D1+T1+P1....................................................................................................... 25
Displacements 2 (OPE) W+D1+T1+P1+WAV1 ............................................................................................ 27
Displacements 3 (OPE) W+D1+T1+P1+WAV2 ............................................................................................ 29
Displacements 4 (OPE) W+D1+T1+P1+WAV3 ............................................................................................ 31
Stresses 1 (OPE) W+D1+T1+P1................................................................................................................ 33
Stresses 2 (OPE) W+D1+T1+P1+WAV1 ..................................................................................................... 38
Stresses 3 (OPE) W+D1+T1+P1+WAV2 ..................................................................................................... 43
Stresses 4 (OPE) W+D1+T1+P1+WAV3 ..................................................................................................... 48
Code Compliance Extended 1 (OPE) W+D1+T1+P1 2 (OPE) W+D1+T1+P1+WAV1 3 (OPE)
W+D1+T1+P1+WAV2 4 (OPE) W+D1+T1+P1+WAV3 .......................................................................................... 53
2
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
Job Description:
ANALYST: SV
PIPE DATA
-----------------------------------------------------------------------------
-----------------------------------------------------------------------------
From 10 To 20 DX= -5,000.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= 30.750 mm. Cor= 3.0000 mm.
GENERAL
T1= 44 C P1= 128.9000 bars Mat= (306)API-5L X65 E= 203,391 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m. Insul= 3,008.7000 kg/cu.m.
Fluid= 185.0000000 kg/cu.m.
RESTRAINTS
Node 10 ANC
Node 20 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
ALLOWABLE STRESSES
B31.8 VIII(2003) Sh1= 448 N./sq.mm. Sh2= 448 N./sq.mm.
Sh3= 448 N./sq.mm. Sh4= 448 N./sq.mm. Sh5= 448 N./sq.mm.
Sh6= 448 N./sq.mm. Sh7= 448 N./sq.mm. Sh8= 448 N./sq.mm.
Sh9= 448 N./sq.mm. Sy= 448 N./sq.mm. Fac= .5000
-----------------------------------------------------------------------------
From 20 To 30 DX= -5,000.000 mm.
GENERAL
RESTRAINTS
Node 30 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 30 To 40 DX= -5,000.000 mm.
GENERAL
RESTRAINTS
Node 40 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 40 To 50 DX= -5,000.000 mm.
GENERAL
RESTRAINTS
Node 50 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 50 To 60 DX= -5,000.000 mm.
GENERAL
RESTRAINTS
3
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
PIPE
Dia= 273.100 mm. Wall= 12.870 mm. Insul= 35.750 mm.
GENERAL
BEND at "TO" end
Radius= 1,365.000 mm. (user) Bend Angle= 90.000
RESTRAINTS
Node 370 +Y K= 114 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 370 To 380 DZ= 5,000.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= 35.750 mm.
GENERAL
RESTRAINTS
Node 380 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 380 To 390 DZ= 5,000.000 mm.
GENERAL
RESTRAINTS
Node 390 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 390 To 400 DZ= 3,930.000 mm.
GENERAL
RESTRAINTS
Node 400 +Y K= 236 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 400 To 410 DZ= 2,000.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.870 mm. Insul= 35.750 mm.
GENERAL
BEND at "TO" end
Radius= 1,365.000 mm. (user) Bend Angle= 90.000
RESTRAINTS
Node 410 +Y K= 120 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 410 To 420 DX= -4,800.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= 35.750 mm.
GENERAL
RESTRAINTS
Node 420 +Y K= 288 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 420 To 430 DX= -200.000 mm.
GENERAL
8
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
RESTRAINTS
Node 580 +Y K= 240 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 580 To 590 DX= -967.500 mm. DZ= 1,975.800 mm.
GENERAL
RESTRAINTS
Node 590 ANC
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
MATERIAL Changes:
10 20 Mat= (306)API-5L X65 E= 203,391 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m.
JOBNAME: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
BEND ELEMENTS
130 140 Radius= 1,365.000 mm. (user)
Bend Angle= 90.000
150 160 Radius= 381.000 mm. (user)
Bend Angle= 90.000
250 260 Radius= 381.000 mm. (user)
Bend Angle= 90.000
260 270 Radius= 381.000 mm. (user)
Bend Angle= 45.000
270 280 Radius= 381.000 mm. (user)
Bend Angle= 45.000
360 370 Radius= 1,365.000 mm. (user)
Bend Angle= 90.000
400 410 Radius= 1,365.000 mm. (user)
Bend Angle= 90.000
570 580 Radius= 1,365.000 mm. (user)
Bend Angle= 26.090
RIGIDS
180 190 RIGID Weight= 1,196.51 N.
190 200 RIGID Weight=11,631.52 N.
200 210 RIGID Weight= 1,196.51 N.
230 240 RIGID Weight= 1,196.50 N.
240 250 RIGID Weight= 1,196.50 N.
11
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
RESTRAINTS Len MU
GAP YIELD Dir
NODE TYPE CNODE STIF1 STIF2 FORCE Vectors
-------+-------+------+----------+----------+----------+---------------------
10 ANC .000 .000 .000
20 +Y 300 .70 .000 1.000 .000
30 +Y 300 .70 .000 1.000 .000
40 +Y 300 .70 .000 1.000 .000
50 +Y 300 .70 .000 1.000 .000
60 +Y 300 .70 .000 1.000 .000
70 +Y 300 .70 .000 1.000 .000
80 +Y 300 .70 .000 1.000 .000
90 +Y 300 .70 .000 1.000 .000
100 +Y 300 .70 .000 1.000 .000
110 +Y 300 .70 .000 1.000 .000
120 +Y 300 .70 .000 1.000 .000
130 +Y 300 .70 .000 1.000 .000
140 +Y 300 .70 .000 1.000 .000
150 +Y 180 .70 .000 1.000 .000
170 X 1.000 .000 .000
170 +Y .000 1.000 .000
220 X 1.000 .000 .000
220 +Y .000 1.000 .000
290 +Y 60 .70 .000 1.000 .000
320 +Y 300 .70 .000 1.000 .000
330 +Y 300 .70 .000 1.000 .000
340 +Y 300 .70 .000 1.000 .000
350 +Y 300 .70 .000 1.000 .000
360 +Y 264 .70 .000 1.000 .000
370 +Y 114 .70 .000 1.000 .000
380 +Y 300 .70 .000 1.000 .000
390 +Y 300 .70 .000 1.000 .000
400 +Y 236 .70 .000 1.000 .000
410 +Y 120 .70 .000 1.000 .000
420 +Y 288 .70 .000 1.000 .000
450 +Y 300 .70 .000 1.000 .000
460 +Y 300 .70 .000 1.000 .000
470 +Y 300 .70 .000 1.000 .000
480 +Y 300 .70 .000 1.000 .000
490 +Y 300 .70 .000 1.000 .000
500 +Y 300 .70 .000 1.000 .000
510 +Y 300 .70 .000 1.000 .000
520 +Y 300 .70 .000 1.000 .000
530 +Y 300 .70 .000 1.000 .000
540 ANC 5400 .000 .000 .000
12
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
DISPLACEMENTS
530 540 Node 5400 DX1= 246.000 mm. DY1= .000 mm.
DZ1= .000 mm.
WIND/WAVE
10 20 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
20 30 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
30 40 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
40 50 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
50 60 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
60 70 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
70 80 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
80 90 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
90 100 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
100 110 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
110 120 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
120 130 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
130 140 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
140 150 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
150 160 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
160 170 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
170 180 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
180 190 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
190 200 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
200 210 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
13
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
COORDINATE REPORT
/--------------------(mm.)----------------------/
NODE X Y Z
10 .0000 -45127.6992 .0000
20 -5000.0000 -45127.6992 .0000
30 -10000.0000 -45127.6992 .0000
40 -15000.0000 -45127.6992 .0000
50 -20000.0000 -45127.6992 .0000
60 -25000.0000 -45127.6992 .0000
70 -30000.0000 -45127.6992 .0000
80 -35000.0000 -45127.6992 .0000
90 -40000.0000 -45127.6992 .0000
100 -45000.0000 -45127.6992 .0000
110 -50000.0000 -45127.6992 .0000
120 -55000.0000 -45127.6992 .0000
130 -60000.0000 -45127.6992 .0000
140 -65000.0000 -45127.6992 .0000
150 -65000.0000 -45127.6992 3000.0000
160 -65000.0000 -44280.6992 3000.0000
170 -65000.0000 -44280.6992 3750.0000
180 -65000.0000 -44280.6992 4288.0000
190 -65000.0000 -44280.6992 4488.0000
200 -65000.0000 -44280.6992 5326.0000
210 -65000.0000 -44280.6992 5526.0000
220 -65000.0000 -44280.6992 6019.0000
230 -65000.0000 -44280.6992 6509.0000
17
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
INPUT LISTING
BEND DATA:
TYPE KEY:
3 - Welding Tee
4 - Sweepolet
5 - Weldolet
10. 20. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
20. 30. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
30. 40. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
40. 50. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
50. 60. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
60. 70. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
70. 80. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
80. 90. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
90. 100. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
100. 110. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
110. 120. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
120. 130. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
130. 140. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
140. 150. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
150. 160. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
160. 170. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
170. 180. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
180. 190. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
190. 200. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
200. 210. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
210. 220. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
220. 230. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
230. 240. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
240. 250. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
250. 260. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
260. 270. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
270. 280. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
280. 290. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
290. 300. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
300. 310. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
310. 320. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
320. 330. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
330. 340. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
340. 350. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
350. 360. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
360. 370. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
370. 380. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
380. 390. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
390. 400. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
400. 410. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
410. 420. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
420. 430. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
430. 440. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
440. 450. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
450. 460. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
21
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
460. 470. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
470. 480. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
480. 490. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
490. 500. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
500. 510. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
510. 520. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
520. 530. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
530. 540. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
150. 550. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
550. 560. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
560. 570. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
570. 580. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
580. 590. 0.0003 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
WAVE VECTOR 1
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and 1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45300.000
Wave Height: 14800.000
Wave Period: 12.800
22
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
WAVE VECTOR 2
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and -1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45300.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: -1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1400.000
2 22500.000 1200.000
3 45300.000 700.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 3
23
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
WAVE VECTOR 4
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1400.000
Z: ection cosines --X: and 0.000 -1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45300.000
Wave Height: 14800.000
Wave Period: 12.800
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 0.000 -1.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1400.000
2 22500.000 1200.000
3 45300.000 700.000
24
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
25
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:49:30
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-OPN
Licensed To: B & W ID: 13709
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 10 133.72 224.07 59.7 20 133.72 224.07 59.7
2 (OPE) 10 133.72 224.07 59.7 20 133.72 224.07 59.7
3 (OPE) 10 133.72 224.07 59.7 20 133.72 224.07 59.7
4 (OPE) 10 133.72 224.07 59.7 20 133.72 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
2 (OPE) 30 133.72 224.07 59.7 40 133.72 224.07 59.7
3 (OPE) 30 133.72 224.07 59.7 40 133.72 224.07 59.7
4 (OPE) 30 133.72 224.07 59.7 40 133.72 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
4 (OPE) 90 133.72 224.07 59.7 100 133.72 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 160 133.81 224.07 59.7 170 133.81 224.07 59.7
2 (OPE) 160 133.81 224.07 59.7 170 133.81 224.07 59.7
3 (OPE) 160 133.81 224.07 59.7 170 133.81 224.07 59.7
4 (OPE) 160 133.81 224.07 59.7 170 133.81 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 220 133.81 224.07 59.7 230 133.81 224.07 59.7
4 (OPE) 220 133.81 224.07 59.7 230 133.81 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
2 (OPE) 350 133.72 224.07 59.7 360 133.72 224.07 59.7
3 (OPE) 350 133.72 224.07 59.7 360 133.72 224.07 59.7
4 (OPE) 350 133.72 224.07 59.7 360 133.72 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
4 (OPE) 410 241.59 403.33 59.9 420 133.72 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (OPE) 480 133.72 224.07 59.7 490 133.72 224.07 59.7
2 (OPE) 480 133.72 224.07 59.7 490 133.72 224.07 59.7
3 (OPE) 480 133.72 224.07 59.7 490 133.72 224.07 59.7
4 (OPE) 480 133.72 224.07 59.7 490 133.72 224.07 59.7
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (OPE) 150 133.72 224.07 59.7 550 133.72 224.07 59.7
4 (OPE) 150 133.72 224.07 59.7 550 133.72 224.07 59.7
Table of Contents
INPUT LISTING .................................................................................................................................................... 2
MISCELLANEOUS COMPUTED DATA ..................................................................................................................... 18
Displacements 1 (HYD) W+D1+T1+HP....................................................................................................... 25
Displacements 2 (HYD) W+D1+T1+HP+WAV1 ............................................................................................ 27
Displacements 3 (HYD) W+D1+T1+HP+WAV2 ............................................................................................ 29
Displacements 4 (HYD) W+D1+T1+HP+WAV3 ............................................................................................ 31
Stresses 1 (HYD) W+D1+T1+HP................................................................................................................ 33
Stresses 2 (HYD) W+D1+T1+HP+WAV1 ..................................................................................................... 38
Stresses 3 (HYD) W+D1+T1+HP+WAV2 ..................................................................................................... 43
Stresses 4 (HYD) W+D1+T1+HP+WAV3 ..................................................................................................... 48
Code Compliance Extended 1 (HYD) W+D1+T1+HP 2 (HYD) W+D1+T1+HP+WAV1 3 (HYD)
W+D1+T1+HP+WAV2 4 (HYD) W+D1+T1+HP+WAV3 .......................................................................................... 53
2
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
Job Description:
ANALYST: SV
PIPE DATA
-----------------------------------------------------------------------------
-----------------------------------------------------------------------------
From 10 To 20 DX= -5,000.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= 30.750 mm.
GENERAL
T1= 29 C PHyd= 219.4500 bars Mat= (306)API-5L X65 E= 203,391 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m. Insul= 3,008.7000 kg/cu.m.
Fluid=1025.0000000 kg/cu.m.
RESTRAINTS
Node 10 ANC
Node 20 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
ALLOWABLE STRESSES
B31.8 VIII(2003) Sh1= 448 N./sq.mm. Sh2= 448 N./sq.mm.
Sh3= 448 N./sq.mm. Sh4= 448 N./sq.mm. Sh5= 448 N./sq.mm.
Sh6= 448 N./sq.mm. Sh7= 448 N./sq.mm. Sh8= 448 N./sq.mm.
Sh9= 448 N./sq.mm. Sy= 448 N./sq.mm. Fac= .5000
-----------------------------------------------------------------------------
From 20 To 30 DX= -5,000.000 mm.
GENERAL
RESTRAINTS
Node 30 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 30 To 40 DX= -5,000.000 mm.
GENERAL
RESTRAINTS
Node 40 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 40 To 50 DX= -5,000.000 mm.
GENERAL
RESTRAINTS
Node 50 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 50 To 60 DX= -5,000.000 mm.
GENERAL
RESTRAINTS
3
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
PIPE
Dia= 273.100 mm. Wall= 12.870 mm. Insul= 35.750 mm.
GENERAL
BEND at "TO" end
Radius= 1,365.000 mm. (user) Bend Angle= 90.000
RESTRAINTS
Node 370 +Y K= 114 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 370 To 380 DZ= 5,000.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= 35.750 mm.
GENERAL
RESTRAINTS
Node 380 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 380 To 390 DZ= 5,000.000 mm.
GENERAL
RESTRAINTS
Node 390 +Y K= 300 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 390 To 400 DZ= 3,930.000 mm.
GENERAL
RESTRAINTS
Node 400 +Y K= 236 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 400 To 410 DZ= 2,000.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.870 mm. Insul= 35.750 mm.
GENERAL
BEND at "TO" end
Radius= 1,365.000 mm. (user) Bend Angle= 90.000
RESTRAINTS
Node 410 +Y K= 120 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 410 To 420 DX= -4,800.000 mm.
PIPE
Dia= 273.100 mm. Wall= 12.700 mm. Insul= 35.750 mm.
GENERAL
RESTRAINTS
Node 420 +Y K= 288 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 420 To 430 DX= -200.000 mm.
GENERAL
8
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
RESTRAINTS
Node 580 +Y K= 240 N./mm. Mu = .70
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
-----------------------------------------------------------------------------
From 580 To 590 DX= -967.500 mm. DZ= 1,975.800 mm.
GENERAL
RESTRAINTS
Node 590 ANC
WAVE
Drag Coef= .700 Added Mass Coef= 2.290 Lift Coef= .900
MATERIAL Changes:
10 20 Mat= (306)API-5L X65 E= 203,391 N./sq.mm.
v = .300 Density= 7,850.0000 kg/cu.m.
JOBNAME: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
BEND ELEMENTS
130 140 Radius= 1,365.000 mm. (user)
Bend Angle= 90.000
150 160 Radius= 381.000 mm. (user)
Bend Angle= 90.000
250 260 Radius= 381.000 mm. (user)
Bend Angle= 90.000
260 270 Radius= 381.000 mm. (user)
Bend Angle= 45.000
270 280 Radius= 381.000 mm. (user)
Bend Angle= 45.000
360 370 Radius= 1,365.000 mm. (user)
Bend Angle= 90.000
400 410 Radius= 1,365.000 mm. (user)
Bend Angle= 90.000
570 580 Radius= 1,365.000 mm. (user)
Bend Angle= 26.090
RIGIDS
180 190 RIGID Weight= 1,196.51 N.
190 200 RIGID Weight=11,631.52 N.
200 210 RIGID Weight= 1,196.51 N.
230 240 RIGID Weight= 1,196.50 N.
240 250 RIGID Weight= 1,196.50 N.
11
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
RESTRAINTS Len MU
GAP YIELD Dir
NODE TYPE CNODE STIF1 STIF2 FORCE Vectors
-------+-------+------+----------+----------+----------+---------------------
10 ANC .000 .000 .000
20 +Y 300 .70 .000 1.000 .000
30 +Y 300 .70 .000 1.000 .000
40 +Y 300 .70 .000 1.000 .000
50 +Y 300 .70 .000 1.000 .000
60 +Y 300 .70 .000 1.000 .000
70 +Y 300 .70 .000 1.000 .000
80 +Y 300 .70 .000 1.000 .000
90 +Y 300 .70 .000 1.000 .000
100 +Y 300 .70 .000 1.000 .000
110 +Y 300 .70 .000 1.000 .000
120 +Y 300 .70 .000 1.000 .000
130 +Y 300 .70 .000 1.000 .000
140 +Y 300 .70 .000 1.000 .000
150 +Y 180 .70 .000 1.000 .000
170 X 1.000 .000 .000
170 +Y .000 1.000 .000
220 X 1.000 .000 .000
220 +Y .000 1.000 .000
290 +Y 60 .70 .000 1.000 .000
320 +Y 300 .70 .000 1.000 .000
330 +Y 300 .70 .000 1.000 .000
340 +Y 300 .70 .000 1.000 .000
350 +Y 300 .70 .000 1.000 .000
360 +Y 264 .70 .000 1.000 .000
370 +Y 114 .70 .000 1.000 .000
380 +Y 300 .70 .000 1.000 .000
390 +Y 300 .70 .000 1.000 .000
400 +Y 236 .70 .000 1.000 .000
410 +Y 120 .70 .000 1.000 .000
420 +Y 288 .70 .000 1.000 .000
450 +Y 300 .70 .000 1.000 .000
460 +Y 300 .70 .000 1.000 .000
470 +Y 300 .70 .000 1.000 .000
480 +Y 300 .70 .000 1.000 .000
490 +Y 300 .70 .000 1.000 .000
500 +Y 300 .70 .000 1.000 .000
510 +Y 300 .70 .000 1.000 .000
520 +Y 300 .70 .000 1.000 .000
530 +Y 300 .70 .000 1.000 .000
540 ANC 5400 .000 .000 .000
12
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
DISPLACEMENTS
530 540 Node 5400 DX1= 131.000 mm. DY1= .000 mm.
DZ1= .000 mm.
WIND/WAVE
10 20 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
20 30 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
30 40 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
40 50 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
50 60 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
60 70 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
70 80 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
80 90 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
90 100 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
100 110 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
110 120 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
120 130 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
130 140 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
140 150 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
150 160 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
160 170 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
170 180 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
180 190 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
190 200 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
200 210 WAVE Drag Coef= .700
Added Mass Coef= 2.290 Lift Coef= .900
13
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
INPUT LISTING
INPUT LISTING
INPUT LISTING
COORDINATE REPORT
/--------------------(mm.)----------------------/
NODE X Y Z
10 .0000 -45127.6992 .0000
20 -5000.0000 -45127.6992 .0000
30 -10000.0000 -45127.6992 .0000
40 -15000.0000 -45127.6992 .0000
50 -20000.0000 -45127.6992 .0000
60 -25000.0000 -45127.6992 .0000
70 -30000.0000 -45127.6992 .0000
80 -35000.0000 -45127.6992 .0000
90 -40000.0000 -45127.6992 .0000
100 -45000.0000 -45127.6992 .0000
110 -50000.0000 -45127.6992 .0000
120 -55000.0000 -45127.6992 .0000
130 -60000.0000 -45127.6992 .0000
140 -65000.0000 -45127.6992 .0000
150 -65000.0000 -45127.6992 3000.0000
160 -65000.0000 -44280.6992 3000.0000
170 -65000.0000 -44280.6992 3750.0000
180 -65000.0000 -44280.6992 4288.0000
190 -65000.0000 -44280.6992 4488.0000
200 -65000.0000 -44280.6992 5326.0000
210 -65000.0000 -44280.6992 5526.0000
220 -65000.0000 -44280.6992 6019.0000
230 -65000.0000 -44280.6992 6509.0000
17
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
INPUT LISTING
BEND DATA:
TYPE KEY:
3 - Welding Tee
4 - Sweepolet
5 - Weldolet
10. 20. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
20. 30. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
30. 40. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
40. 50. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
50. 60. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
60. 70. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
70. 80. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
80. 90. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
90. 100. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
100. 110. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
110. 120. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
120. 130. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
130. 140. 0.810 0.866 0.483 0.000E+00 0.000E+00 0.000E+00 .000 .000
140. 150. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
150. 160. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
160. 170. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
170. 180. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
180. 190. 5.983 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
190. 200. 13.880 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
200. 210. 5.983 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
210. 220. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
220. 230. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
230. 240. 5.983 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
240. 250. 5.983 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
250. 260. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
260. 270. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
270. 280. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
280. 290. 0.800 0.009 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
290. 300. 5.983 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
300. 310. 5.983 0.016 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
310. 320. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
320. 330. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
330. 340. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
340. 350. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
350. 360. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
360. 370. 0.810 1.025 0.483 0.000E+00 0.000E+00 0.000E+00 .000 .000
370. 380. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
380. 390. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
390. 400. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
400. 410. 0.810 1.025 0.483 0.000E+00 0.000E+00 0.000E+00 .000 .000
410. 420. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
420. 430. 5.983 1.794 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
430. 440. 5.983 1.794 0.484 0.000E+00 0.000E+00 0.000E+00 NA NA
440. 450. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
450. 460. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
460. 470. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
470. 480. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
480. 490. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
490. 500. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
500. 510. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
510. 520. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
520. 530. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
530. 540. 0.800 1.025 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
150. 550. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
550. 560. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
20
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
560. 570. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
570. 580. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
580. 590. 0.800 0.866 0.484 0.000E+00 0.000E+00 0.000E+00 .000 .000
10. 20. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
20. 30. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
30. 40. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
40. 50. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
50. 60. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
60. 70. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
70. 80. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
80. 90. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
90. 100. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
100. 110. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
110. 120. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
120. 130. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
130. 140. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
140. 150. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
150. 160. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
160. 170. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
170. 180. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
180. 190. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
190. 200. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
200. 210. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
210. 220. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
220. 230. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
230. 240. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
240. 250. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
250. 260. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
260. 270. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
270. 280. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
280. 290. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
290. 300. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
300. 310. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
310. 320. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
320. 330. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
330. 340. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
340. 350. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
350. 360. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
360. 370. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
370. 380. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
380. 390. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
390. 400. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
400. 410. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
410. 420. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
420. 430. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
430. 440. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
440. 450. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
450. 460. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
21
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
460. 470. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
470. 480. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
480. 490. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
490. 500. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
500. 510. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
510. 520. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
520. 530. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
530. 540. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
150. 550. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
550. 560. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
560. 570. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
570. 580. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
580. 590. 0.0001 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
WAVE VECTOR 1
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and 1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45300.000
Wave Height: 6900.000
Wave Period: 7.100
22
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
WAVE VECTOR 2
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and -1.000 0.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45300.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: -1.000 0.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1100.000
2 22500.000 800.000
3 45300.000 300.000
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
WAVE VECTOR 3
23
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
WAVE VECTOR 4
Velocity Units : mm./sec.
Elevation / Height Units: mm.
Density Units : kg/cu.m.
Current Profile Type: LINEAR TABLE
Surface Velocity: 1100.000
Z: ection cosines --X: and 0.000 -1.000
Wave Theory MODIFIED STOKES 5TH
Stream Function Order: 11.000
Water Depth: 45300.000
Wave Height: 6900.000
Wave Period: 7.100
Wave Kinematics Factor: 1.000
Direction cosines --X: and Z: 0.000 -1.000
Phase Specified at Origin
Phase Angle: 0.000
Free Surface Elevation: 0.000
Kinematic Viscosity: 1.030
Density: 1025.000
Veloci and
1 0.000 1100.000
2 22500.000 800.000
3 45300.000 300.000
24
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
4 0.000 0.000
5 0.000 0.000
6 0.000 0.000
7 0.000 0.000
8 0.000 0.000
9 0.000 0.000
10 0.000 0.000
25
C A E S A R I I VER.5.00.7, (Build 070122) FEB 22,2007 10:55:36
Jobname: D:\SAKTHI\CAESAR\STD\TIE-IN10\LOOP\TIEIN10-HYD
Licensed To: B & W ID: 13709
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 10 231.07 448.15 51.6 20 231.07 448.15 51.6
2 (HYD) 10 231.07 448.15 51.6 20 231.07 448.15 51.6
3 (HYD) 10 231.07 448.15 51.6 20 231.07 448.15 51.6
4 (HYD) 10 231.07 448.15 51.6 20 231.07 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
2 (HYD) 30 231.07 448.15 51.6 40 231.07 448.15 51.6
3 (HYD) 30 231.07 448.15 51.6 40 231.07 448.15 51.6
4 (HYD) 30 231.07 448.15 51.6 40 231.07 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
4 (HYD) 90 231.07 448.15 51.6 100 231.07 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 160 231.17 448.15 51.6 170 231.17 448.15 51.6
2 (HYD) 160 231.17 448.15 51.6 170 231.17 448.15 51.6
3 (HYD) 160 231.17 448.15 51.6 170 231.17 448.15 51.6
4 (HYD) 160 231.17 448.15 51.6 170 231.17 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 220 231.17 448.15 51.6 230 231.17 448.15 51.6
4 (HYD) 220 231.17 448.15 51.6 230 231.17 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
2 (HYD) 350 231.07 448.15 51.6 360 231.07 448.15 51.6
3 (HYD) 350 231.07 448.15 51.6 360 231.07 448.15 51.6
4 (HYD) 350 231.07 448.15 51.6 360 231.07 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
4 (HYD) 410 231.07 448.15 51.6 420 231.07 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
1 (HYD) 480 231.07 448.15 51.6 490 231.07 448.15 51.6
2 (HYD) 480 231.07 448.15 51.6 490 231.07 448.15 51.6
3 (HYD) 480 231.07 448.15 51.6 490 231.07 448.15 51.6
4 (HYD) 480 231.07 448.15 51.6 490 231.07 448.15 51.6
Allowable Allowable
Code Stress Code Stress
Load Case From Node Stress Ratio % To Node Stress Ratio %
N./sq.mm. N./sq.mm.
N./sq.mm. N./sq.mm.
3 (HYD) 150 231.07 448.15 51.6 550 231.07 448.15 51.6
4 (HYD) 150 231.07 448.15 51.6 550 231.07 448.15 51.6