Professional Documents
Culture Documents
ABSTRACT • Process engineering professional with over 12+ years of experience in Conceptual
studies, FEED and detailed engineering (EPC) for upstream Oil & Gas facilities (FPSO,
MOPU, Fixed Platform, FLNG), Liquefied Natural Gas (LNG) facilities and refinery unit.
• Extensive experience in design and optimization of Oil & Gas processing facilities.
• Experience of FEED/EPC for LNG facilities and have good knowledge of APCI AP-
C3MR technology.
• Worked as lead/area lead for various projects (LNG/Offshore Projects).
• Exposure to various codes, standards and design engineering practices.
SKILLS & Highly proficient in developing Basic Engineering / FEED package and perform Detailed
ABILITIES Engineering which involves following activities: -
• Process simulation and perform configuration studies
• PFD/P&ID development for large FEED/EPC projects
• Relief load calculation, depressurization calculations, fire survivability analysis and low
temperature study
• Cause & effect matrix, SAFE chart, SAT Tables, Alarm & Trip register
• Equipment sizing and rating (two phase separators, three phase separators,
exchangers)
• Hydraulic calculation for compressor, pumps and non-pump system
• Process datasheets for equipment (separators, pumps, compressors) and instruments
• Participation in HAZOP and SIL studies as design representative
• Participation in design review meetings with client
• Developed many in-house process calculation spreadsheets for SHI and Bechtel
DESIGN TOOLS HYSYS, PRO II, UNISIM, FLARENET, KG TOWER, SMART PLANT REVIEW
EXPERIENCE SENIOR ROCESS ENGINEER, BECHTEL INDIA PVT LTD. (DEC. 2014 – PRESENT)
Port Arthur LNG FEED & Bridging (Port Arthur, Tx)
Port Arthur LNG is based on APCI AP-C3MR liquefaction technology with capacity of 11.68 MMTPA.
As Lead Engineer for the bridging activities, responsibilities for this project were as followings:
• Prepared PFD/UFDs for warm end/Utilities/LNG storage and offloading
• Equipment sizing calculations and preparation of process datasheets for both warm end and
cold end
Page 1 of 3
• Relief load estimation and depressurization calculation for Gas Pretreatment, NGL Section
and Liquefaction area. Performed fire survivability analysis.
• Utility Balances (Fuel gas, Cooling Water, Hot Oil)
• Prepared training manual for quick on-boarding of new engineers
Detailed Engineering for Driftwood LNG (Tellurian Inc.)
Driftwood LNG is based on Chart liquefaction technology with capacity of 25.8 MMTPA. As area lead
for the detailed engineering and responsibilities for this project were as following:
• Development of Piping and Instrumentation Diagram (LNG Storage and offloading, BOG
compression system, Flare system and Refrigerant system)
• Performed DPDT calculation and preparation of DPDT diagram
• Equipment sizing and preparation of datasheet
• Pump, control valve, relief load calculation and lateral sizing
• Prepared design engineering change notice and trends
FEED Verification of RG LNG (NextDecade, LLC)
Rio Grande LNG is based on APCI AP-C3MR liquefaction technology. As area lead for feed
verification, responsibilities were as following:
• Reviewed PFD and P&IDs
• Reviewed of Process Datasheets
• Verified MR compressor/Propane compressor hydraulics
FEED & Detailed Engineering for Exxon Mobil Scanfiner project
Naphtha Hydrotreating Unit (SCANfining technology) is to hydro-desulfurize D-10 bottoms to meet
the stringent product sulfur specification. Acted as responsible engineer for FEED and detailed
engineering. Responsibilities for this project were as following:
• Development of P&IDs from licensor flow scheme
• Perform DPDT calculation and preparation of diagram
• Control valve hydraulic calculation
• Pump, control valve, PSV lateral calculations
• Participated in client model reviews
FEED for Naphtha hydrotreating unit (PT Pertamina Refinery)
RFCC Naphtha Hydrotreating Unit (Axens Prime G+TM unit) is to produce low-sulphur RFCC gasoline.
Acted as responsible engineer for FEED and responsibilities for this project were as following:
• Development of P&IDs from licensor flow scheme and line sizing
• Relief load estimation
• Participation in client model review and HAZOP studies
SENIOR PROCESS ENGINEER, SAMSUNG HEAVY INDUSTRIES LTD. (JUL. 2008 – DEC. 2014)
FEED for Inpex Masela FLNG (INPEX) (On Deputation to SHI-Korea)
Floating LNG is to be located at Abadi gas field in Indonesian offshore with gas liquefaction capacity
of 2.5 MMTPA. Acted as Area Lead for the FEED and responsibilities for this project were as
following:
• Development of conceptual PFDs based on design basis and specification
Worked on several proposal engineering: HRD Platform (ONGC), Sagar Pragati (ONGC), ONGC
cluster-7 FPSO, Knarr FPSO (British Gas) and MHN (ONGC)
EDUCATION • Bachelor of Engineering (2008) from University of Rajasthan, Jaipur (Raj.) with
aggregate of 83%