Professional Documents
Culture Documents
Carrier
P.O. Box 4808
Carrier Parkway PH189
A United Technologies Company Syracuse, New York 13221
DATE PAGE OF
Material Specification 05/31/2011 1 3
TITLE: SUPERSEDES DOC. NO. DATED
SCOPE:
This specification establishes the requirements for an air drying finish medium gloss gray water-borne
enamel. This material contains a V.O.C. (Volatile Organic Content) of 1.8 lbs. per gallon at the application
viscosity.
MATERIAL: For Carrier plants to purchase materials covered by this specification, and use in Carrier
products, the material must be approved by Materials and Technical Services and the supplier’s quality
system must be Qualified/Certified by the Carrier user plant.
SUPPLIER APPROVAL: Materials and Technical Services will test, in accordance with the requirements of
this specification, a quantity of material necessary to give valid results. The material must be supplied from a
production run using standard production methods. Only material that has met all requirements will be
classified as “approved”. Approved suppliers are listed on the last page of this specification.
PERFORMANCE REQUIREMENTS:
The following requirements shall be met by all materials covered by this specification:
This document and the information contained therein is proprietary to Carrier Corporation and shall not be used or disclosed to
others, in whole or in part, without the written authorization of Carrier Corporation.
Filename: ph189_Rev.A.docx Savedate: 9/21/2011 2:54:00 PM User: msdt6uc
DOC. NO.
Carrier
P.O. Box 4808
Carrier Parkway PH189
A United Technologies Company Syracuse, New York 13221
DATE PAGE OF
Material Specification 05/31/2011 2 3
TITLE: SUPERSEDES DOC. NO. DATED
GRAY WATERBORNE, LOW VOC, LOW HAPS ENAMEL PH189 06/03/1999
APPROVED BY / DATE M&TS APPROVAL / DATE P. C. A. NUMBER
SPECIAL REQUIREMENTS:
1. Application Air Assisted Airless
2. Surface to be Top Coated The paint shall be applied to
surfaces that have been treated with
Material Specification RW04-11
and primed with PJ104 or PJ106.
3. Reduction None.
4. Dry Film Thickness Recommended 0.003 in. min.
5. Dry to touch, minutes @ 73 F, 55% RH 30
Through dry, hours @ 73 F, 55% RH 24
6. Gloss, per ASTM D523, 60 deg. 60
7. Color Gray, to match Federal Standard
595a, #26231.
8. Adhesion, cross-hatched The finished material shall meet
ASTM D3359 using SCOTCH
brand tape #610 or equivalent. The
tape shall show no paint adhering to
it, except for very light lines of paint
particles remaining from the
brushed scribe lines.
9. Flash Point, SETA FLASH, °F above 200°F.
This document and the information contained therein is proprietary to Carrier Corporation and shall not be used or disclosed to
others, in whole or in part, without the written authorization of Carrier Corporation.
Filename: ph189_Rev.A.docx Savedate: 9/21/2011 2:54:00 PM User: Anthony Molavi
DOC. NO.
Carrier
P.O. Box 4808
Carrier Parkway PH189
A United Technologies Company Syracuse, New York 13221
DATE PAGE OF
Material Specification 05/31/2011 3 3
TITLE: SUPERSEDES DOC. NO. DATED
NOTES:
1. THE INFORMATION ON THIS PAGE IS CONFIDENTIAL TO CARRIER.
2. DO NOT PURCHASE MATERIAL FROM SUPPLIERS WHO ARE NOT APPROVED.
3. THE CARRIER USER PLANT, OR DESIGNATED LEAD PURCHASING PLANT, MUST
QUALIFY/CERTIFY ALL SUPPLIERS OF PRODUCTION MATERIALS IN
ACCORDANCE WITH THE EXISTING CARRIER SUPPLIER QUALITY ASSURANCE
REQUIREMENTS. SUPPLIERS CAN BE QUALIFIED/CERTIFIED ONLY AFTER
THEY HAVE BEEN APPROVED BY MATERIALS AND TECHNICAL SERVICES.
This document and the information contained therein is proprietary to Carrier Corporation and shall not be used or disclosed to
others, in whole or in part, without the written authorization of Carrier Corporation.
Filename: ph189_Rev.A.docx Savedate: 9/21/2011 2:54:00 PM User: Anthony Molavi