Professional Documents
Culture Documents
The versatility of the SPIROL® Coiled Pin makes it the ideal fastener to meet
the specific engineering and economic objectives of pinning applications.
Our broad range of standard pins is designed to meet most requirements.
If a special diameter, length, duty, material, tolerance or pin configuration is
needed, we are ready to assist you.
Challenge us!
EXTRA
HEAVY DUTY
LARGE
LIGHT
METRIC DUTY
SIZES
SPECIAL
LENGTHS
STANDARD
DUTY
NICKEL
STAINLESS
EXTRA
LIGHT
DUTY
HEAVY FLARED
CARBON DUTY
STEEL
HEADED
CHROME STAINLESS
SPECIAL
DIAMETERS
SPECIAL LONG CHAMFER
MATERIALS
MINIATURE
SPECIAL SHAPES
2
What Differentiates A Coiled Pin?
PRIOR TO INSTALLATION
FLEXIBILITY
UNDER LOAD
UNDER APPLIED LOADS
1
Unique Features
Only Coiled Pins utilize the spiral spring concept…a contracts and expands in unison. Application of an
recognized superior spring design. It imparts to excessive load compresses the pin into a solid tube.
SPIROL® Coiled Pins unique features not found in Further loading causes shear failure. In properly
other spring pins. More than fasteners, SPIROL® engineered applications, this condition should not
Coiled Pins are also shock absorbing elements which occur.
are integral, active components of a total assembly.
EQUAL STRESS DISTRIBUTION
ABSORBS SHOCK AND VIBRATIONS Stresses imparted to the pin during installation
The spiral spring concept represents broad design compression, as well as stresses resulting from
latitude in the control and development of pin flexibility. applied loads, shock and vibration, are distributed
The engineered flexibility of SPIROL® Coiled Pins equally throughout the SPIROL® Coiled Pin cross
provides for compression of the pin into the hole and section. This concept and uniform flexing and strength
for continued flexibility after insertion. Without this are related and inherent features of the spiral design.
flexibility, the total load applied to the pin would be Stress concentration results in a weak point where
transmitted to the hole wall without dampening the progressive shear failure starts and premature fatigue
impact. Since the hole material is normally softer occurs. SPIROL® Coiled Pins have no weak points
than the pin, elongation or enlargement of the hole of stress concentration.
would result. The fit between the hole and the pin
would become loose, increasing the impact force and DUTIES
accelerating the rate of hole damage. The inevitable Flexibility, strength, and diameter must be in the
result would be premature failure of the assembly. proper relationship to each other and to the mating
In properly engineered applications, the flexibility of host materials to maximize the unique features of the
SPIROL® Coiled Pins dampens shock and vibration, SPIROL® Coiled Pin. Strength and flexibility must be
thus eliminating hole damage on all the components balanced. A pin too strong for the applied load would
of the assembly resulting in maximum product life. not flex, causing damage to the hole. A pin not strong
enough would flex too much and fatigue. Balanced
UNIFORM STRENGTH AND FLEXIBILITY strength and flexibility must be combined with a large
Force direction does not affect the flexibility and shear enough pin diameter to transmit applied loads without
strength of the SPIROL® Coiled Pin. Compression damaging the hole wall. That is why SPIROL® Coiled
causes the pin to coil from the outer edge inwardly Pins are offered in different duties...to provide a variety
towards the center. When loads are applied and of strength, flexibility and diameter combinations to
relieved, as happens in shock and vibration, the pin suit different mating host materials.
2
…and Other Advantages
REUSABLE
When driven from a hole, the SPIROL® Coiled Pin
INCREASED HOLE
TOLERANCE
expands to its original diameter. The same pin may
RANGES REDUCE be reused in the same hole.
MANUFACTURING COST
3
STANDARD COILED PINS
Specifications and Technical Data
Identification Code
Coiled Pin 8 mm dia. x 32 mm length standard duty/carbon steel/plain finish
CLDP 8 x 32 M B K
Third letter specifies finish
Second letter specifies material
First letter specifies duty of pin
Second figure specifies length
First figure specifies nominal diameter
Prefix specifies pin type
90˚
MEASURE
PIN O.D.
BETWEEN
POINTS
NOTES
• Standard specifications apply except where otherwise specified.
• The standard finish for stainless steel pins is plain. Passivated pins are available at an additional cost.
• Zinc plating is not available for alloy steel pins.
• Special sizes, duties, materials and finishes, including oil-free pins, are available upon request.
4
Standard Duty Coiled Pins – Inch
ASME B18.8.2
L ØD
ØB ØD
.031 .047 .062 .078 .094 .125 .156 .187 .250 .312 .375 .500 .625 .750
NOMINAL DIAMETER ➤ 1/32 3/64 1/16 5/64 3/32 1/8 5/32 3/16 1/4 5/16 3/8 1/2 5/8 3/4
MAX. .035 .052 .072 .088 .105 .138 .171 .205 .271 .337 .403 .535 .661 .787
DIAMETER ØD
MIN. .033 .049 .067 .083 .099 .131 .163 .196 .260 .324 .388 .516 .642 .768
B DIAMETER MAX. .029 .045 .059 .075 .091 .121 .152 .182 .243 .304 .366 .488 .613 .738
CHAMFER C LENGTH REF. .024 .024 .028 .032 .038 .044 .048 .055 .065 .080 .095 .110 .125 .150
RECOMMENDED MAX. .032 .048 .065 .081 .097 .129 .160 .192 .256 .319 .383 .510 .635 .760
HOLE SIZE MIN. .031 .047 .061 .077 .093 .124 .155 .185 .247 .308 .370 .493 .618 .743
STANDARD LENGTHS
.031 .047 .062 .078 .094 .125 .156 .187 .250 .312 .375 .500 .625 .750
NOMINAL DIAMETER ➤ 1/32 3/64 1/16 5/64 3/32 1/8 5/32 3/16 1/4 5/16 3/8 1/2 5/8 3/4
.125 1/8 Interchangeable
Inch and mm Pins
.187 3/16 Inch mm
.250 1/4 Diameter Diameter
.312 5/16 .031 1/32 0.8
.047 3/64 1.2
.375 3/8 .078 5/64 2.0
.437 7/16 .156 5/32 4.0
.500 1/2 .312 5/16 8.0
.625 5/8 16.0
.562 9/16
.625 5/8
.750 3/4
LENGTHS
.875 7/8
1.000 1
1.250 1-1/4
1.500 1-1/2
1.750 1-3/4
2.000 2
Nominal Pin Length Length Tolerance
2.250 2-1/4 Nominal Pin Size ø1/32 - 3/8 ø1/2 - 3/4
2.500 2-1/2 L ≤ 2.000 ±0.010 ±0.025
2.750 2-3/4 2.000 < L ≤ 3.000 ±0.015 ±0.025
3.000 < L ±0.025 ±0.025
3.000 3
Nominal ✝ Pin Straightness Gage Length
3.250 3-1/4 Pin Length Tolerance ±0.005
3.500 3-1/2 L ≤ 1.000 .007 1.000
3.750 3-3/4 1.000 < L ≤ 2.000 .010 2.000
2.000 < L .013 3.000
4.000 4
Only available in chrome and nickel stainless steel Only available in alloy steel
ØB ØD
.062 .078 .094 .125 .156 .187 .250 .312 .375 .500
NOMINAL DIAMETER ➤ 1/16 5/64 3/32 1/8 5/32 3/16 1/4 5/16 3/8 1/2
MAX. .070 .086 .103 .136 .168 .202 .268 .334 .400 .532
DIAMETER ØD
MIN. .066 .082 .098 .130 .161 .194 .258 .322 .386 .514
B DIAMETER MAX. .059 .075 .091 .121 .152 .182 .243 .304 .366 .488
CHAMFER C LENGTH REF. .028 .032 .038 .044 .048 .055 .065 .080 .095 .110
RECOMMENDED MAX. .065 .081 .097 .129 .160 .192 .256 .319 .383 .510
HOLE SIZE MIN. .061 .077 .093 .124 .155 .185 .247 .308 .370 .493
STANDARD LENGTHS
.062 .078 .094 .125 .156 .187 .250 .312 .375 .500
NOMINAL DIAMETER ➤ 1/16 5/64 3/32 1/8 5/32 3/16 1/4 5/16 3/8 1/2
.187 3/16 Interchangeable
.250 1/4 Inch and mm Pins
Inch mm
.312 5/16 Diameter Diameter
.375 3/8 .078 5/64 2.0
.437 7/16 .156 5/32 4.0
.312 5/16 8.0
.500 1/2
.562 9/16
.625 5/8
.750 3/4
.875 7/8
LENGTHS
1.000 1
1.250 1-1/4
1.500 1-1/2
1.750 1-3/4
2.000 2 Nominal Pin Length Length Tolerance
2.250 2-1/4 Nominal Pin Size ø1/16 - 3/8 ø1/2
2.500 2-1/2 L ≤ 2.000 ±0.010 ±0.025
2.000 < L ≤ 3.000 ±0.015 ±0.025
2.750 2-3/4 3.000 < L ±0.025 ±0.025
3.000 3 Nominal ✝ Pin Straightness Gage Length
3.250 3-1/4 Pin Length Tolerance ±0.005
3.500 3-1/2 L ≤ 1.000 .007 1.000
1.000 < L ≤ 2.000 .010 2.000
3.750 3-3/4 2.000 < L .013 3.000
4.000 4
ØB ØD
STANDARD LENGTHS
.062 .078 .094 .125 .156 .187 .250
NOMINAL DIAMETER ➤ 1/16 5/64 3/32 1/8 5/32 3/16 1/4
.250 1/4 Interchangeable
Inch and mm Pins
.312 5/16 Inch mm
Diameter Diameter
.375 3/8 .078 5/64 2.0
.156 5/32 4.0
.437 7/16
.500 1/2
.562 9/16
.625 5/8
LENGTHS
.750 3/4
.875 7/8
1.000 1
1.250 1-1/4 Nominal Pin Length Length Tolerance
Nominal Pin Size ø1/16 - 1/4
1.500 1-1/2 L ≤ 2.000 ±0.010
2.000 < L ±0.015
1.750 1-3/4
Nominal ✝ Pin Straightness Gage Length
2.000 2 Pin Length Tolerance ±0.005
L ≤ 1.000 .007 1.000
2.250 2-1/4 1.000 < L ≤ 2.000 .010 2.000
2.000 < L .013 3.000
2.500 2-1/2
Only available in chrome and nickel stainless steel Available in all materials – except alloy steel
Special sizes, duties, materials and finishes, including oil-free pins, are available upon request.
✝ Pin must fall through a hole gauge in length equal to the next one-inch increment over the pin length with a hole equal to the maximum
specified pin diameter plus the straightness tolerance by its own weight.
7
Standard Duty Coiled Pins – Metric
ISO 8750 • ASME B18.8.3M
L ØD
ØB ØD
MAX. 0.91 1.15 1.35 1.73 2.25 2.78 3.30 4.40 5.50 6.50 8.63 10.80 12.85 17.00 21.10
DIAMETER ØD
MIN. 0.85 1.05 1.25 1.62 2.13 2.65 3.15 4.20 5.25 6.25 8.30 10.35 12.40 16.45 20.40
B DIAMETER MAX. 0.75 0.95 1.15 1.40 1.90 2.40 2.90 3.90 4.85 5.85 7.80 9.75 11.70 15.60 19.60
CHAMFER C LENGTH REF.
0.30 0.30 0.40 0.50 0.70 0.70 0.90 1.10 1.30 1.50 2.00 2.50 3.00 4.00 4.50
RECOMMENDED MAX. 0.84 1.04 1.24 1.60 2.10 2.60 3.10 4.12 5.12 6.15 8.15 10.15 12.18 16.18 20.21
HOLE SIZE MIN. 0.80 1.00 1.20 1.50 2.00 2.50 3.00 4.00 5.00 6.00 8.00 10.00 12.00 16.00 20.00
STANDARD LENGTHS
NOMINAL DIAMETER ➤ 0.8 1 1.2 1.5 2 2.5 3 4 5 6 8 10 12 16 20
5 Interchangeable
6 mm and Inch Pins
8 mm Inch
Diameter Diameter
10 0.8 .031 1/32
12 1.0 .039
14 1.2 .047 3/64
2.0 .078 5/64
16 4.0 .156 5/32
18 8.0 .312 5/16
20 16.0 .625 5/8
22
24
26
LENGTHS
28
30
35
40
45
50 Nominal Pin Length Length Tolerance
55 Nominal Pin Size ø0.8 - 10 ø12 - 20
60 L ≤ 10 ±0.25 N/A
65 10 < L ≤ 50 ±0.5 ±0.5
50 < L ±0.75 ±0.75
70
✝ Gage Hole Diameter
75 Specified Maximum
80 Nominal Pin Diameter Plus Gage Length
85 Pin Length Min. Max. ±0.15
90 L ≤ 24 0.18 0.2 25
95 24 < L ≤ 50 0.3 0.34 50
50 < L 0.42 0.48 75
100
Only available in chrome and nickel stainless steel Only available in alloy steel
ØB ØD
MAX. 1.71 2.21 2.73 3.25 4.30 5.35 6.40 8.55 10.65 12.75
DIAMETER ØD
MIN. 1.61 2.11 2.62 3.12 4.15 5.15 6.18 8.25 10.30 12.35
B DIAMETER MAX. 1.40 1.90 2.40 2.90 3.90 4.85 5.85 7.80 9.75 11.70
CHAMFER
C LENGTH REF. 0.50 0.70 0.70 0.90 1.10 1.30 1.50 2.00 2.50 3.00
RECOMMENDED MAX. 1.60 2.10 2.60 3.10 4.12 5.12 6.15 8.15 10.15 12.18
HOLE SIZE MIN. 1.50 2.00 2.50 3.00 4.00 5.00 6.00 8.00 10.00 12.00
STANDARD LENGTHS
NOMINAL DIAMETER ➤ 1.5 2 2.5 3 4 5 6 8 10 12
4 Interchangeable
5 mm and Inch Pins
6 mm Inch
8 Diameter Diameter
2.0 .078 5/64
10 4.0 .156 5/32
12 8.0 .312 5/16
14
16
18
20
22
24
LENGTHS
26
28
30
35
40
45
50 Nominal Pin Length Length Tolerance
55 Nominal Pin Size ø1.5 - 10 ø12
60 L ≤ 10 ±0.25 N/A
10 < L ≤ 50 ±0.5 ±0.5
65 50 < L ±0.75 ±0.75
70 ✝ Gage Hole Diameter
75 Specified Maximum
80 Nominal Pin Diameter Plus Gage Length
Pin Length Min. Max. ±0.15
85
L ≤ 24 0.18 0.2 25
90
24 < L ≤ 50 0.3 0.34 50
95 50 < L 0.42 0.48 75
100
Special sizes, duties, materials and finishes, including oil-free pins, are available upon request.
✝ Pin must fall through a hole gauge in length equal to the next 25mm increment over the pin length with a hole equal to the maximum
specified pin diameter plus the straightness tolerance by its own weight.
9
Light Duty Coiled Pins – Metric
ISO 8751 • ASME B18.8.3M
L ØD
ØB ØD
STANDARD LENGTHS
NOMINAL DIAMETER ➤ 1.5 2 2.5 3 4 5 6
10 Interchangeable
mm and Inch Pins
12 mm Inch
Diameter Diameter
14 2.0 .078 5/64
4.0 .156 5/32
16
18
20
22
LENGTHS
24
26
28
Nominal Pin Length Length Tolerance
30 Nominal Pin Size ø1.5 - 6
L ≤ 10 ±0.25
35 10 < L ≤ 50 ±0.5
50 < L ±0.75
40 ✝ Gage Hole Diameter
Specified Maximum
45 Nominal Pin Diameter Plus Gage Length
50 Pin Length Min. Max. ±0.15
L ≤ 24 0.18 0.2 25
55 24 < L ≤ 50 0.3 0.34 50
50 < L 0.42 0.48 75
60
Only available in chrome and nickel stainless steel Available in all materials – except alloy steel
Special sizes, duties, materials and finishes, including oil-free pins, are available upon request.
✝ Pin must fall through a hole gauge in length equal to the next 25mm increment over the pin length with a hole equal to the maximum
specified pin diameter plus the straightness tolerance by its own weight.
10
SPECIAL COILED PINS
11
SERIES 400 HEADED PINS
Specifications and Technical Data
SECTION A•A
SWAGED CHAMFER
When a design calls for the head of the pin to be driven down flush, the radius under the head must be given
clearance. To provide this clearance, either countersink the hole or enlarge the hole in the component adjacent to
the head as shown above by 0.15 mm or .006" over the maximum hole sizes in the specifications.
R Phosphate coated
T Zinc Plated
DIMENSIONAL DATA —
METRIC
PIN DIAMETER HEAD DIMENSIONS CHAMFER LENGTHS
D H E B C L
NOMINAL RECOMMENDED
PIN SIZE THICK- HOLE SIZE
STANDARD DUTY DIAMETER DIA. LENGTH TOLERANCE
NESS
± 0.50
MAX. MIN. MAX. MIN. REF. MAX. REF. MAX. MIN.
1.5 1.73 1.62 2.4 2 0.4 1.4 0.5 1.6 1.5 5 to 18
2 2.25 2.13 3.1 2.6 0.5 1.9 0.7 2.1 2 6 to 22
2.5 2.78 2.65 3.8 3.2 0.7 2.4 0.7 2.6 2.5 8 to 28
3 3.3 3.15 4.6 3.9 0.8 2.9 0.9 3.1 3 10 to 25
3.5 3.84 3.67 5.2 4.6 0.9 3.4 1 3.62 3.5 10 to 45
4 4.4 4.2 6 5.2 1.2 3.9 1.1 4.12 4 12 to 40
5 5.5 5.25 7.4 6.5 1.5 4.85 1.3 5.12 5 14 to 50
Specifications on other metric and inch diameters and lengths are available on request.
The shear strength is the same as that of standard Coiled Pins of equivalent size, material and duty.
12
SERIES 410 FLARED PINS
Specifications and Technical Data
SECTION A•A
SWAGED CHAMFER
When a design calls for the flare of the pin to be driven down flush, the radius under the flare must be given
clearance. To provide this clearance, countersink the hole in the component adjacent to the flare.
Specifications on other metric and inch diameters and lengths are available on request.
The shear strength is the same as that of standard Coiled Pins of equivalent size, material and duty.
13
SERIES 500 EXTRA LIGHT PINS
Specifications and Technical Data
Specifications on other metric and inch diameters and lengths are available on request.
14
SERIES 600 SUPERFLEX PINS
Specifications and Technical Data
H Heavy C Chrome Stainless Steel AISI 420, ISO X30Cr13 (1.4028) HV 460 to 560 P Passivated, oiled
R Phosphate coated
T Zinc plated
D1 D2 B C L
NOMINAL RECOMMENDED
PIN SIZE STANDARD HEAVY STANDARD HEAVY HOLE SIZE TOLERANCES
DIA. LENGTH L ≤ 2.000 ± .010
DUTY DUTY DUTY DUTY 2.000 < L ≤ 3.000 ± .015
3.000 < L ± .025
MAX. MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. REF. MAX. MIN.
.062 1/16 .072 .067 .070 .066 .065 .062 .065 .062 .059 .028 .065 .061 .250 to .625
.078 5/64 .088 .083 .086 .082 .081 .078 .081 .078 .075 .032 .081 .077 .312 to .750
.094 3/32 .105 .099 .103 .098 .097 .094 .097 .094 .091 .038 .097 .093 .375 to 1.000
.125 1/8 .138 .131 .136 .130 .129 .125 .129 .125 .121 .044 .129 .124 .500 to 1.250
.156 5/32 .171 .163 .168 .161 .160 .156 .160 .156 .152 .048 .160 .155 .625 to 1.750
.187 3/16 .205 .196 .202 .194 .192 .187 .192 .187 .182 .055 .192 .185 .750 to 1.750
.250 1/4 .271 .260 .268 .258 .256 .249 .256 .249 .243 .065 .256 .247 1.000 to 2.250
.312 5/16 .337 .324 .334 .322 .319 .311 .319 .311 .304 .080 .319 .308 1.250 to 3.000
.375 3/8 .403 .388 .400 .386 .383 .373 .383 .373 .366 .095 .383 .370 1.500 to 3.500
1.5 1.73 1.62 1.71 1.61 1.63 1.5 1.63 1.5 1.4 0.5 1.6 1.5 6 to 16
2 2.25 2.13 2.21 2.11 2.13 2 2.13 2 1.9 0.7 2.1 1.99 8 to 20
2.5 2.78 2.65 2.73 2.62 2.64 2.5 2.64 2.5 2.4 0.7 2.6 2.49 10 to 24
3 3.3 3.15 3.25 3.12 3.14 3 3.14 3 2.9 0.9 3.1 2.99 12 to 30
3.5 3.84 3.67 3.79 3.64 3.66 3.5 3.66 3.5 3.4 1 3.62 3.48 14 to 35
4 4.4 4.2 4.3 4.15 4.17 4 4.17 4 3.9 1.1 4.12 3.98 16 to 40
5 5.5 5.25 5.35 5.15 5.18 5 5.18 5 4.85 1.3 5.12 4.95 20 to 45
6 6.5 6.25 6.4 6.18 6.21 6 6.21 6 5.85 1.5 6.13 5.95 24 to 55
8 8.63 8.3 8.55 8.25 8.29 8 8.29 8 7.8 2 8.17 7.93 30 to 75
10 10.75 10.35 10.65 10.3 10.34 10 10.34 10 9.75 2.5 10.2 9.93 40 to 85
Specifications on other metric and inch diameters and lengths are available on request.
The shear strength is the same as that of standard Coiled Pins of equivalent size, material and duty.
15
Design Guidelines
16
Installation and Automatic Assembly
CHALLENGE US!
17
Innovative fastening solutions. Technical Centers
Lower assembly costs. Americas SPIROL International Corporation
30 Rock Avenue
Danielson, Connecticut 06239 U.S.A.
Tel. +1 860 774 8571
Fax. +1 860 774 2048
SPIROL Shim Division
321 Remington Road
Stow, Ohio 44224 U.S.A.
Tel. +1 330 920 3655
Fax. +1 330 920 3659
Slotted Spring Pins
SPIROL West
1950 Compton Avenue, Unit 111
Corona, California 92881 U.S.A.
Tel. +1 951 273 5900
Solid Pins & Drive Fax. +1 951 273 5907
Coiled Spring Pins Studs SPIROL Canada
3103 St. Etienne Boulevard
Ground Hollow Windsor, Ontario N8W 5B1 Canada
Dowels Tel. +1 519 974 3334
Fax. +1 519 974 6550
SPIROL Mexico
Carretera a Laredo KM 16.5 Interior E
Col. Moisés Saenz
Rolled Tubular Apodaca, N.L. 66613 Mexico
Components Dowel Bushings / Tel. +52 81 8385 4390
Spring Dowels Fax. +52 81 8385 4391
SPIROL Brazil
Rua Mafalda Barnabé Soliani, 134
Compression Comercial Vitória Martini, Distrito Industrial
Limiters CEP 13347-610, Indaiatuba, SP, Brazil
Inserts for Plastics Tel. +55 19 3936 2701
Fax. +55 19 3936 7121
Spacers
Europe SPIROL France
Cité de l’Automobile ZAC Croix Blandin
18 Rue Léna Bernstein
51100 Reims, France
Tel. +33 3 26 36 31 42
Precision Washers Fax. +33 3 26 09 19 76
Precision Shims & SPIROL United Kingdom
Precision Machined
Nuts Thin Metal Stampings 17 Princewood Road
Corby, Northants
NN17 4ET United Kingdom
Tel. +44 1536 444800
Fax. +44 1536 203415
SPIROL Germany
Brienner Strasse 9
80333 Munich, Germany
Tel. +49 931 454 670 74
Disc Springs Fax. +49 931 454 670 75
SPIROL Spain
08940 Cornellà de Llobregat
Barcelona, Spain
Tel. +34 93 193 05 32
Fax. +34 93 193 25 43
SPIROL Czech Republic
Insert Installation Sokola Tůmy 743/16
Technology Ostrava-Mariánské Hory 70900
Pin Installation Parts Feeding Czech Republic
Technology Technology Tel/Fax. +420 417 537 979
Asia SPIROL Asia Headquarters
Please refer to www.SPIROL.com for the most current specifications and standard offering. Pacific 1st Floor, Building 22, Plot D9, District D
Printed materials may be out of date. No. 122 HeDan Road
Wai Gao Qiao Free Trade Zone
SPIROL Application Engineers will review your application needs and work with Shanghai, China 200131
your design team to recommend the best solution. One way to start the process Tel. +86 21 5046 1451
Fax. +86 21 5046 1540
is to visit our Optimal Application Engineering portal at www.SPIROL.com.
SPIROL Korea
ISO/TS 16949 Certified
ISO 9001 Certified e-mail: info@spirol.com 160-5 Seokchon-Dong
Songpa-gu, Seoul, 138-844, Korea
Tel. +86 (0) 21 5046-1451
4 © 2014 SPIROL International Corporation 03/14
SPIROL.com Fax. +86 (0) 21 5046-1540