Professional Documents
Culture Documents
5. A commutator is _______.
a. a ditching machine
b. the inter-poles of a generator
c. a device for causing the alternating currents generated in the armature to flow in the same direction in the internal circuit
d. a transformer with a common conductor
7. To fasten a terra cotta wall you should use which of the following?
a. wooden plug b. lag bolt c. expansion bolt d. toggle bolt
8. If a 240 volt heater is used on 120 volt, the amount of heat produced will be _______.
a. twice as great b. four times as great c. ¼ as much d. the same
11. The transferring of electrons from one material to another would be __________.
a. electrochemistry b. static electricity c. solar electricity d. piezoelectricity
12. A minimum thickness of ___________ inch/inches of concrete over conduits and raceways should be used to prevent cracking.
a. 1 b. 2 c. 3 d. 4
15. The usual service conditions under which transformer should be able to carry its rated load are _____.
I. at rated secondary voltage or not in excess of 105% of the rated value
II. at rated frequency
III. temperature of the surrounding cooling air at no time exceeding 40 0 (1400F) and average temperature of the surrounding
cooling air any 24-hour period not exceeding 300C (860F)
HABILIS EE TRAINING CENTER, INC.
61st Isabel Ramiro Road, Purok 6A, Tambo-Hinaplanon,
Iligan City, 9200 Tel No. (063) 2250809 Refresher Day 17
__________________________________________________________________________
a. I only b. II only c. III only d. I, II and III
17. Conductors supplying two or more motors shall have an ampacity equal to the sum of the full-load current rating of all motors plus
_______ % of the highest rated motor in the group.
a. 25 b. 80 c. 100 d. 125
22. Which of the following would cause the most power to be dissipated in the form of heat?
a. XL b. XC c. resonance d. resistance
24. An electrician in the industry would check first the _____ to correct a low power factor.
a. resistance b. hysteresis c. inductive load d. reluctance
25. Single conductor cable runs within a building are generally more common than multicable runs because ________.
a. of conduit fill b. of the temperature
c. the splicing is easier d. the weight is evenly distributed
26. ______ has the highest electrical breakdown strength and the longest life over all other materials used for insulation.
a. rubber insulation b. woven cloth
c. impregnated paper d. thermoplastic
28. To adjust a voltage generated by a constant speed DC generator, you would change the _____.
a. stator b. slip rings c. brushes d. field current
29. The generator which is best suited for electroplating power is a _______ generator.
a. split-phase b. six pole c. separately excited d. compound
34. A motor enclosure designed and constructed to contains sparks or flashes that may ignite surrounding gas or vapor is
called ________.
a. non-ventilated b. encapsulated c. explosion proof d. water cooled
37. The phenomenon whereby a circuit stores electrical energy is called __________.
a. inductance b. capacitance c. resistance d. susceptance
38. A general term including material, fittings, devices, appliances, fixtures, apparatus and the like used as part of, or in
connection with, an electrical installation is __________.
a. premises wiring system b. service equipment
c. utilization equipment d. equipment
39. A switch intended for use in general distribution and branch circuits. It is rated in amperes, and it is capable of
interrupting its rated at its rated voltage, is a __________ switch.
a. bypass isolation b. general use c. isolating d. transfer
40. The permanent of joining metallic parts to form an electrically conductive path that will ensure electrical continuity and
the capacity to conduct safely any current likely to be imposed is known as ________.
a. ordinary tap joint b. scarf joint c. Britannia joint d. bonding
41. An instrument that is used to measure the diameter of a wire or cable to thousands of an inch is a __________.
a. galvanometer b. micrometer c. hydrometer d. ruler
44. Rigid metal conduit is permitted for wiring in hazardous locations if the conduit is threaded and made up wrench tight
with at least _______ full threads.
a. 4 b. 5 c. 7 d. 9
45. A circuit breaker that has purposely introduced into it a delay in the tripping action and which delay decreases as the
magnitude of the current increases is a __________ circuit breaker.
a. inverse time b. adjustable c. control vented d. vented power
46. It is the intent of this code that the factory installed internal wiring or the construction of equipment need not be
inspected at the time of installation of the equipment, except to________.
a. detect alteration
b. detect damage
c. detect insulation type
HABILIS EE TRAINING CENTER, INC.
61st Isabel Ramiro Road, Purok 6A, Tambo-Hinaplanon,
Iligan City, 9200 Tel No. (063) 2250809 Refresher Day 17
__________________________________________________________________________
a. I only b. II only c.I and II only d. I, II & III
47. A premises wiring system whose power is derived from a source such as transformer that has no direct connection to
the supply conductors originating in another system is a/an ______ system.
a. integrated b. separately derived c. interactive d. isolated
48. Listed or labeled equipment shall be installed, used or both, in accordance with any instructions included_________.
a. by the foremen
b. in the listing or labeling
c. with the equipment from the manufacturer
49. Where conductors with an ampacity higher than the ampere rating or setting of the overcurrent device are used, the
______ shall determine the circuit rating.
a. conductor ampacity b. overcurrent device
c. combibed rating d. derated ampacity
50. _________ are permitted to protect motor branch circuit conductors from overload.
I. Thermal relays II. Inverse time circuit breakers III. Time delay fuses
a. I only b. II only c. II & III only d. I, II & III