Professional Documents
Culture Documents
There are total 65 questions carrying 100 marks: Q.1 to Q.25 (25 questions) will carry
one mark each (sub-total 25 marks). Q.26 to Q.55 (30 questions) will carry two marks each
(sub-total 60 marks).Question pairs (Q.48,Q 49) and (Q. 50, Q 51) are common data questions
and question pairs (Q.52, Q.53) and (Q.54, Q.55) are linked answer questions. The answer to
the second question of the last two pairs will depend on the answer to the first question of the
pair. If the first question in the linked pair is wrongly answered or is un-attempted, then the
answer to the second question in the pair will not be evaluated. Q 56 to Q 60 (5 questions) will
carry one mark each (sub-total 5 marks). Q 61 to Q 65 (5 questions) will carry two marks each
( sub-total 10 marks).
Negative Marking: For Q.1 to Q.25, 1/3 mark will be deducted for each wrong answer. For
Q.26 to Q.55, 2/3 mark will be deducted for each wrong answer. The question pairs (Q.52,
Q.53), and (Q.54, Q.55) are questions with linked answers. There will be negative marks only
for wrong answer to the first question of the linked answer question pair i.e. for Q.52 and
Q.54, 2/3 mark will be deducted for each wrong answer. There is no negative marking for Q.53
and Q.55. For Q.56 to Q.60, 1/3 mark will be deducted for each wrong answer. For Q.61 to
Q.65, 2/3 mark will be deducted for each wrong answer.
Fill Objective Response Sheet (ORS) using a soft HB pencil. Do not use the ORS for any
rough work. You may like to use the Answer Book for any rough work, if needed.
Q.3 Let A be an nxn matrix st. A2 = I and Y be an n- dimensional vector. Then the
linear system of equations Ax = y has
(a) No solutions
(b) Unique sol n s.
(c) More than one but infinity many independent so l n s.
(d) Infinitely many independent solutions.
Q.4 Let X be a Poisson variable st. 2p(x = 0) = p(x = 2) then the mean of the poisson
distribution is
(a) 4 (b) 2 (c) 2 (d) − 2
Q.5 Let X be a non singular matrix. Then the inverse of the matrix AA t is
( )
t
(a) Equals A −1 A −1 (b) Does not exists
Q.14 The number of elements that comprise the signature of a single point lathe
cutting tool is
(a) 4 (b) 5 (c) 6 (d) 7
Q.15 In case of a circular section the relation between maximum shear stress and
average shear stress
(a) τ max = 32 τ mean (b) τ max = τ mean (c) τ max = 32 τ mean (d) τ max = 43 τ mean
Q.17 In a flat belt tension in the tight side (T1) = 250 N, Tension in the slack side
(T2) = 226 N, centrifugal tension (Tc) = 534 N, then what should be the Initial
tension in the belt?
(a) 250 N (b) 772 N (c) 277 N (d) 500 N
W2
W1 + W2 W1 + W2 W1 W2
(a) W1 + W2 (b) (c) (d)
2 W1 W2 W1 + W2
Q.19 There are two bars one prismatic and one conical length and specific weight
of both are same. Ratio of their elongation due to their own weight will be
(a) 0. 5 : 1 (b) 1 : 1 (c) 2 : 1 (d) 3 : 1
Q.20 Value of Wahl stress factor for springs with increase in value of c
(a) Decrease (b) increase
(c) Remain same (d) does not depend upon C
Q.22 A 40 mm thick sheet is rolled with 500 mm diameter rolls to reduce thickness
without any charge in its width. The friction coefficient at the work-roll
interface is 0.2. The minimum possible thickness of the sheet that can be
produced in a single pass is
(a) 30 mm (b) 15 mm (c) 25 mm (d) 37 mm
Q.24 Which flame in oxy – acetylene gas welding has got 3 distinct colour zone?
(a) Carburizing flame (b) Oxidizing flame
(c) Neuter flame (d) No such flame
Q.25 Which inert gas is commonly used for shielding in use of case of thin work
piece and low voltage applied?
(a) Argon (b) Helium (c) CO2 (d) None
3. ⎡⎣ ( 0,1,0 )( 1,0,1)(1,1,0 ) ⎤⎦
Q.28 For a scalar function f (x, y, z) = x2 + 3y2 + 2z2 , the directional derivatives at
G G JG
the point p (1, 2, -1) in the direction of vector i − j + 2k is
y2 x2
The equation y2 uxx − 2xy uxy + x uyy − x ux y uy
2
Q.29 + is
(a) elliptic (b) parabolic (c) hyperbolic (d) None of the above
∫ te
−3t
Q.30 Value of sin dt
0
Q.32 Two shafts are connected by a universal joint. The driving shaft rotator at a
uniform speed 120 rpm. Total fluctuation of speed does not exceed 10 rpm.
Calculate minimum speed of shaft
(a) 511 (b) 105 (c) 115 (d) 15
Q.33 Hitesh products Ltd (HPL) produces an item, which requires shearing
operation first followed by punching operation. There are 5 different jobs to
be processed, the processing times for which are given below:
Job 1 2 3 4 5
Shear Time 4 4 10 6 2
Punch Time 5 1 4 10 3
Q.35 Dry Saturated steam at 5 bar with negligible velocity expands isentropically
in a convergent nozzle to 1 bar dryness fraction 0.94. Determine the velocity
of steam leaving the nozzle.
at P1 = 5 bar , hg = 2747.5 KJ / kg
at P = 1 bar , hf = 417.5 KJ / kg, hg = 2258 KJ / kg
(a) 444 m/s (b) 446 m/s (c) 644 m/s (d) 1000 m/s
Q.36 A geometrically similar open channel model is constructed with 5:1 scale. If
model measure discharge of 0.2 m3/s, the corresponding discharge in
prototype is
(a) 5 m3/s (b) 25 m3/s (c) 1 m3/s (d) 125 m3/s
Q.37 How much heat would be generated in the spot welding of two sheets of 1 mm
thick steel that required a current of 10000 A for 0.1 seconds? An effective
resistance of 100 μΩ is assumed.
(a) 1000 kJ (b) 5 kJ (c) 1 kJ (d) 2 kJ
Q.38 Fig shows a hoisting apparatus in which span AB 5 m long is free to turn in a
vertical plane through A and B and is fastened by a cable BC 3 m long to a
point C, 6 m vertically above. A weight of 1500 kg is supported by a cable at B.
neglecting the weight of space and cable the force along AB and BC will be
C
6
B
5
1500 kg
A
Figure
(a) 1250 and 750 Kgf (b) 1500 and 1000 Kgf
(c) 1000 and 1500 Kgf (d) 1500 and 1250 Kgf
Q.39 An engine with 80% mechanical efficiency develops b.p of 48 kW. Assuming
friction as constant, what will be mechanical efficiency at half load?
(a) 40% (b) 53% (c) 67% (d) 80%
Q.44 A Casting 200 × 200 × 70mm 3 size solidifies in 10 min. Determine the
3
solidification time for 200 × 100 × 10mm under similar conditions.
(a) 0.734 min (b)0.846 min (c) 0.648 min (d) 0.648 min
Q.45 To cut a blank of 25 mm wide and 30 mm long form a 1.5 mm thick metal strip,
if the ultimate shear stress of the material is 450 N/mm2. Determine the work
done if the percentage of penetration is 25% of material thickness.
(a) 75 J (b) 72 J (c) 82 J (d)28 J
Q.53 What are the number of orders per year with overall annual sell of 5200?
(a) 16 (b) 52 (c) 30 (d) cannot be calculated
Q.57 Choose the word which is nearest in meaning to the given word.
AUSTERE
(a) Proud (b) Rigorous (c) Revered (d) Very poor
Q.59 The average age of 10 members of a committee is the same as it was 4 years
ago, because an old member has been replaced by a young member. Find how
much younger is the new member?
(a) 44 (b) 40 (c) 30 (d) 35
Q.60 If n is a natural number greater than 1, then 1075n − 1075n−1 is not divisible by
which of the following
(a) 15 (b) 23 (c) 43 (d) 179
1010
Q.62 Let M = 1010 . If M ends with N zeros and N ends with P zeros, how many
digits are there in P?
(a) 2 (b) 3 (c) 10 (d) 11
Q.63 If a is an integer , then for how many integer values of n can the quadratic
equation x2 − (2a + 3)x + 4n = 0 have real and equal roots for x ?
(a) 0 (b) 1 (c) 2 (d) 3
Q.64 If the arithmetic mean of (39)11 and (62)9 is (144)n , then sum of
(32)4 and (21)5 in a system with radix (base) n is
(a) 140 (b) 110 (c) 100 (d) 50
Q.65 Two fair dice are thrown simultaneously. What is the probability that one die
shown up a number greater then “4” and then other number shown up a
number less than “3”?
(a) 1/9 (b) 4/9 (c) 2/9 (d) 1/18
ME Test-3 Answer
1. Ans. c
Exp. AB ≠ BA in general
2. Ans. a
2 2
⎡ ⎛ dy ⎞2 ⎤ ⎛ d2y ⎞
Exp. ⎢1 + ⎜ ⎟ ⎥ = ⎜ 2 ⎟
⎢⎣ ⎝ dx ⎠ ⎥⎦ ⎝ dx ⎠
Degree – 3
Order – 2
3. Ans. b
Exp. A2 = I
⇒ det ( A.A ) = det I
⇒ ( det A ) . ( det A ) = 1
⇒ (det A)2 = 1
⇒ det A = ±1
By crammer’s rule system of equation has unique solution.
4. Ans. b.
Exp. Here X is Poisson variable
e− m m r
∴ p(x = r) = , where m = means of the distribution. r = 0,1,2,3,……..
r!
∴ 2p ( x = 0 ) = p ( x = 2 )
e− m m 0 e− m m 2
⇒ 2. =
0! 2!
⇒ m2 = 4
⇒ m = ±2
5. Ans. c
Exp. A is non singular ⇒ A is square matrix
Now AA t is define.
( AA ) = ( A )
t t
t t
∴ A t = AA t
6. Ans. (b)
7. Ans. (a)
8. Ans. (b)
Exp. Fettling is cleaning of cast
9. Ans. (b)
Exp. For normal substance; 3 preparers and proper 2 properties.
10. Ans. (b)
11. Ans. (b)
12. Ans. (b)
13. Ans. (b)
14. Ans. (d)
W1
W2
a
Figure
W2
a=
W1 + W2
T = W1a
W1 W2
T=
W1 + W2
19. Ans. (d)
Exp. Elongation of prismatic bar
γl 2
=
2E
γl 2
Elongation of conical bar =
6E
ratio = 3 : 1
20. Ans. (a)
4C − 1 0.615
Exp. Wahl stress correction factor = +
4C − 4 C
21. Ans. (c)
Exp. Max inspection is required on production line is stress linked for man production
22. Ans. (a)
Exp. (∆h)max = µ2R = 0.22x250 = 10 mm
23. Ans. (a)
24. Ans. (a)
25. Ans. (a)
Exp. Argon → thin walled plate, Low voltage
Helium → thick walled plate,High voltage
CO2 → Usedonly with DECP(reversepolarity)
26. Ans. d
Exp. z = 0 is pole of order 2n + 1
( 2n ) ! z→0 ⎩⎪ dz ⎣ ⎦ ⎭⎪
1 d2n
= lim 2n ( cos z )
( 2n ) ! z→0 dz
1
= ( − 1) n
( )
2n !
2πi × ( −1)
n
∴ ∫ f ( z )dz =
c ( 2n ) !
27. Ans. b
28. Ans. b
− − −
Exp. ∇f = 2x i + 6y j+ 4zk
− − −
∇f⎥ p = 2 i + 12 j− 4k
− − −
Now unit vector in the direction of i − j+ 2k is
∧ G G JG 1 G G JJG
n= (i − j + 2k) = (i − j + 2k)
12 + ( −1) + 22
2 6
2 − y2 x2 2
Exp. A = λ , B = −2xy , C = x , D = ,E = , F = 0, G=0
x y
B2 − 4AC = 4x2y2 − 4y2x2 = 0
The given equation represents parabola.
30. Ans. b
∞ ∞
−d ⎛ 1 ⎞
Exp. ∫ te
−3t
dt = ∫ te− st sin tdt = L {t sin t} =
0 0
ds ⎜⎝ s2 + 1 ⎟⎠
= 42 + 4 × 4 × 3 − 0.5
= 16 + 48 − 0.5
= 8 − 0.5 = 7.5cm
32. Ans. (c)
Exp. Let α = greatest permissible angle between the shaft axes then
10 = 120
(1 − cos α ) 2
or α = 16.4o
( cos α )
N
N max = = 125 rpm
cos16.4o
N min = N cos α =120 × cos16.4o = 115 rpm
33. Ans. (c)
34. Ans. (b)
35. Ans. (c)
Exp. h2 = hf2 + X2hg2 = 2540 KJ / kg
V= 2000 ( h1 − h2 )
36. Ans. (b)
Exp. (velocity ratio)
vp Lp/T Lp
= α = = 5 p − prototype
vm Lm /T Lm
Ap L p2
α = 25 m-model
Am Lm 2
Qp Apvp
Disch arg ratio = = 25 × 5 = 125
Qm Am vm
0.2 250
Qp = 125 × Qm = 125 × = = 25m 3 / sec
10 10
37 Ans. (c)
Exp. Q = I 2Rt = (10,000)2 × (100 × 10−6 ) × (0.1)J
38. Ans. (a)
Exp. If we draw force triangle it will be similar to ΔABC
C
Fbc
Fac
B
Fab
A
Figure
From similarly
For any query E-mail: swapan_mondal_01@yahoo.co.in
Last Test Series will be uploaded on 1 feb
GATE-2013 (Full Length)
S K Mondal’s Test Series -2
F AB F BC 1500
= =
5 3 6
1500 × f
⇒ FAB = = 1250Kgf
6
1500 × 3
FBC = = 750Kgf
6
39. Ans. (c)
bp 48
Exp. I.P = = × 10 = 60kW
ηm 0.8
Friction power = I.P – B.P = 12 kW
48
At half load BP = but friction power will be same.
2
24 24
` = = 66.67%
24 + 12 36
40. Ans. (a)
Exp. Where Ta atmospheric temperature
h heat transfer coefficient
Δt Surface heat transfer on one side
1
Q= q AL = hA(Tw − Ta )
2
qL
Tw = Ta +
2h
Tw Tw Ta
⎜ ⎟
⎝ A2 ⎠
45. Ans. (d)
Exp. F = P.t.τ
For any query E-mail: swapan_mondal_01@yahoo.co.in
Last Test Series will be uploaded on 1 feb
GATE-2013 (Full Length)
S K Mondal’s Test Series -2
W= F × punch travel
Punch travel = percentage penetration = 0.25 × t
46. Ans. (a)
E E 2.4 × 106
Exp. K= = = = 2.1 × 106
3 (1 − 2v ) 3 (1 − 2v ) 3(1 − 0.62)
47. Ans. (a)
600
⎛ To ⎞
Exp. Availability = mc p ∫ ⎜ 1 − T ⎟ dT
300 ⎝ ⎠
⎡ 600 ⎤
= 10 × 4.2 × ⎢( 600 − 300 ) − 300ln
⎣ 300 ⎥⎦
= 10 × 4.2 × ( 600 − 210 ) = 3780 kJ
48. Ans. (c)
49. Ans. (b)
50. Ans. (a)
( D − d)
D σ
Exp. Hoopstress ( σ ) = E −1 =⇒
d d E
D 120 d
⇒ = 5
+ 1 = 1.0006 ⇒ d = = 11.993 m
d 2 × 10 1.0006
51. Ans. (a)
D−d 6
Exp. πD = πd(1 + αt) Or αt = = 4
d 10
6 1
t= 4
× −6
= 51.3 0 C
10 11.7 × 10
52. Ans. (a)
2c3R
Exp. Q= c1 → inventary carrying cost
c1
c3 → ordering cost per order
100×5200×2
= =316.2
10.40
53. Ans. (a)
5200
Exp. No. of order per year = = 16.4 = 16
316.2
54. Ans. (a)
Exp. Critical damping coefficient = CC = 2mwn
k C
(As critical damping, ωn2 − a2 = 0 where ωn = , a = C , CC = 2mωn )
m 2m
k
ωn = = 10
m
CC = 2 × 40 × 10 = 800N m
55. Ans. (a)
C F 400
Exp. Damping ratio = C= = = 40,CC = 800
CC v 10