Professional Documents
Culture Documents
CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
Concrete Beam Design, for New or Existing, Based on ACI 318-19
ANALYSIS
CHECK FLEXURAL CAPACITY emax = 0.003 0.85 f c'
A s' f s'
(
2 0.85 f C' )
e o e max or , E c 57 f C , E s 29000ksi
'
Ec Fc
e e 2
0.85 f C 2
' c c ,
for 0 e c e o Parabolic
fC e o e o
0.85 f C , for e c e o
'
Asfy
e s E s , for e s e t
fS
f , for e s e t
y
Cover = 1.5 in, (ACI 318 20.6.1) rprov'd = 0.0055 < rmax = 0.0119 , (ACI 318 9.3.3.1)
d= 45.44 in > rmin = 0.0033 , (ACI 318 9.6.1)
d' = 2.44 in [Satisfactory]
f= 0.90 , (ACI 318-19 21.2) c= 5.39 in, by pure math method
ec,max = 0.0006 Fc = 334.34 kips
es,max = 0.0050 , (ACI 318-19 21.2.2) dc = 1.85 in
V u 10f b wd f
'
V C 2b wd fc
'
c 137.93 kips
230.0 < 517.3 kips [Satisfactory]
f=
where 0.75
(1.9 A 2500r wB) b wd
V C + 144.10 kips ,<== applicable
Check shear reinforcement (ACI 22.5)
f
0 , for V u V c where A MIN ( f
'
c , 100 ) 63.25
2
50b w V d
Av 0.75 f 'c b w fV c B MIN u , 1.0
s MAX , , for V u fV c M u 0.871
Re qD fy f 2
y
f
V u V c , for fV c V u
f df y
Av
= 0.716 in2 / ft < s 0.800 in2 / ft [Satisfactory]
Pr ovD
Check spacing limits for shear reinforcement (ACI 22.6.9.5)
V u fV c
Vs 0.00 kips, (ACI 22.5.1.1)
f
d
, 24) for V s 4b wd
'
MIN ( f
2 c
S max, shear = 22 > S= 12 in
MIN ( d , 12) for V s 4b wd f
'
[Satisfactory]
4 c
(cont'd)
CHECK TORSION CAPACITY
Check section limitation (ACI 22.7.7.1)
2
T u Ph
2
Vu where f= 0.75 (ACI 21.2)
+ f V C + 8 f 'c
2 Ph = 258 in, (perimeter of centerline of outermost closed
b wd 1.7 Aoh b
w
d
transverse torsional reinforcement.)
Aoh = 1,287 in2 (area enclosed by centerline of the outermost
0.215 < 0.474 [Satisfactory] closed transverse torsional reinforcement.)
' Acp
2 where be = MIN(h-hf , 4hf) = 32 in, (one side, ACI 9.2.4.4)
Tu f f c Pcp = 160 in, (outside perimeter of the concrete cross
P cp section.)
36.5 < 36.5 ft-k Acp = 1,216 in2 (area enclosed by outside perimeter of
Torsional reinforcement NOT reqD. concrete cross section.)
T u 4f f c
P cp
36.5 < 146.1
Reduction of the torsional moment can occur.
Determine the corresponding area of longitudinal reinforcement (derived from ACI 22.7.6.1 & 9.6.4.3)
25b w
'
At f 5 Acp f c f
A L MAX P h Ph MAX At ,
yv yv
, in2
s f f yL f s f yv
0.00
yL yL
Determine minimum combined area of longitudinal reinforcement
AL, top = As' +0.5AL = 0.00 in2 < actual [Satisfactory]
AL, bot = As +0.5AL = 5.06 in2 < actual [Satisfactory]