Professional Documents
Culture Documents
Explanation of symbols
Throughout this Operation Manual the following symbols are used:
C Important information or useful hints about usage.
A Warning for hazardous situations with regard to life and property.
B Warning for supply voltage.
4
1
4 - EN
Specifications
Width (cm) 60 60
Depth (cm) 59 59
Specifications of this appliance may change without notice to improve the quality of
the product. Figures in this manual are schematic and may not match your product
exactly.
Values stated on the machine labels or in the documentation accompanying it are
obtained in laboratory in accordance with the relevant standards. Depending on
operational and environmental conditions of the appliance, values may vary.
5 - EN
2 Warnings
Please read the following information. for 3 seconds to cancel the program
Otherwise, there may be the risk of set in your machine before calling
personal injury or material damage. the authorized service.
Moreover, any warranty and reliability
commitment will become void. First Use
• To prepare your machine for
General Safety washing, carry out your first washing
• Never place your machine on a process without loading your
carpet covered floor. Otherwise, machine and with detergent under
lack of airflow from below of your “Cottons 90°C” program.
machine may cause electrical • Ensure that the cold and hot water
parts to overheat. This may cause connections has been made
problems with your washing correctly when installing your
machine. machine. Otherwise, your laundry
• If the power cable or mains plug is may come out hot at the end of the
damaged you must call Authorized washing process and may wear out.
Service for repair. • If the current fuse or circuit breaker
• Check water hoses for wear. Do is less than 16 Amperes, please
not use old/used water inlet hoses. have a qualified electrician install a
These may cause stains on your 16 Ampere fuse or circuit breaker.
laundry. • While using with or without a
• Fit the drain hose into the discharge transformer, do not neglect to have
housing securely to prevent any the grounding installation laid by a
water leakage and to allow machine qualified electrician. Our company
to take in and discharge water as shall not be liable for any damages
required. It is very important that the that may arise when the machine is
water intake and drain hoses are not used on a line without grounding.
folded, squeezed, or broken when • To make your machine ready for
the appliance is pushed into place use, please be sure that the tap
after it is installed or cleaned. water supply and water drainage
• Your washing machine is designed systems are appropriate before
to continue operating in the event calling the authorized service. If they
of a power interruption. You cannot are not, call a qualified plumber to
cancel any program by pressing the have any necessary arrangements
“On/Off button.” Your machine will carried out.
not resume its program when the
power restores. Press the “Start/ Intended use
Pause/Cancel” button for 3 seconds • This product has been designed for
to cancel the program (See, home use.
Cancelling a Program) • The appliance may only be used for
• There may be some water in your washing and rinsing of textiles that
machine when you receive it. This is are marked accordingly.
from the quality control process and • Only detergents, softeners and
is normal. It is not harmful to your supplements suitable for washing
machine. machines may be used.
• Some problems you may encounter • Observe the care instructions
may be caused by the software. labelled on textile products and
Press “Start/Pause/Cancel” button any other instructions given by
6 - EN
companies that produce detergents be solved by information in the
for your machine. operating manual:
• This appliance is not intended for Turn off the machine, unplug it, turn
use by persons (including children) off the water tap and contact an
with reduced physical, sensory authorized service agent.
or mental capabilities, or lack of
experience and knowledge, unless If there are children in your
they have been given supervision house...
or instruction concerning use of the • Electrical appliances may be
appliance by a person responsible dangerous for the children. Keep
for their safety. children away from the machine
when it is operating. Do not let them
Safety instructions tamper with the machine.
• This appliance must be connected • Close the door when you leave the
to an earthed outlet protected by a area where the machine is located.
fuse of suitable capacity. • Store all detergents in a safe place
• The supply and draining hoses must out of reach of the children.
always be securely fastened and
remain in an undamaged state.
• Fit the draining hose to a washbasin
or bathtub securely before starting
up your machine. There may be a
risk of being scalded due to high
washing temperatures!
• Never open the door or remove the
filter while there is still water in the
drum. Otherwise, there may be the
risk of flooding and possible injury
due to the hot water.
• Never force open the locked door!
The door will be ready to open just a
few minutes after the washing cycle
comes to an end.
• Unplug the machine when it is not in
use.
• Never wash down the appliance
with a water hose! There is the risk
of electric shock! Always disconnect
from the mains by unplugging before
cleaning.
• Never touch the plug with wet
hands. Never unplug by pulling
on the cable, always pull out from
the plug only. Do not operate the
machine if the power cord or plug is
damaged.
• Never attempt to repair the machine
yourself. Otherwise, you may be
putting yours and other’s lives in
danger.
• For malfunctions that cannot
7 - EN
3 Installation
Removing packaging bolts in a safe place to reuse when
reinforcement the washing machine needs to be
Tilt the machine to remove the moved again in the future.
packaging reinforcement. Remove the C Never move the appliance without
packaging reinforcement by pulling the the transportation safety bolts
ribbon. properly fixed in place!
Appropriate installation
location
Install the appliance in environments
which have no risk of freezing, in a
stable and level position.
C The floor must be capable of
carrying the load on it!
C If the washing machine and a drier
are placed on top of each other,
their approximate weight together
may reach 180 kg when they are
full.
Important:
Opening the transportation • Do not place the appliance on top of
locks the power cable.
C Transportation safety bolts must • Keep at least 1cm distance from the
be removed before operating the edges of other furniture.
washing machine! Otherwise, the • Place the machine on a firm surface;
machine will be damaged! do not position it on a long pile rug
or such like surfaces.
1. Loosen all the bolts with a spanner
until they rotate freely (“C”) Adjusting the feet
C Do not use any tools to loosen the
lock nuts. Otherwise, they can be
damaged.
1. Manually (by hand) loosen the lock
2. Remove transportation safety bolts nuts on the feet.
by turning them gently. 2. Adjust them until the machine
stands level and firm.
3. Important: Tighten all lock nuts up
again.
9 - EN
• In case the hose is elevated B The appliance must not be operated
after laying it on the floor level or unless it is repaired! There is the risk
close to the ground (less than of electric shock!
40 cm above the ground), water
discharge becomes more difficult Destroying the packaging
and the laundry may come out wet.
Therefore, the heights described in material
the figure should be followed. Packaging material can be dangerous to
• To prevent dirty water refilling the children. Keep the packaging materials
machine, and to allow for easy out of reach of children or dispose
discharge, the end of the hose them by classifying according to
must not be submerged in the drain waste directives. Do not dispose them
water. The end of the hose must be together with normal domestic waste.
able to take in air. The hose should Packaging materials of your machine are
be pushed into the drainage for manufactured from recyclable materials.
more than 15 cm. If it is too long
you may have it shortened. Disposing of the old machine
• The end of the hose should not be Dispose of your old appliance in an
bent, it should not be stepped on environmental friendly manner.
and it must not be folded between • You may refer to your local agent or
the drain and the machine. solid waste collection center in your
• The length of the hose is too short, municipality to learn how to dispose
you may add an extension hose of your machine.
to the original section. The length Before disposing of your old washing
of the hose must not be longer machine, cut off the mains plug and
than 3.2 m after coming out of the make the door lock unusable.
machine. To avoid water leakage
failures, the connection between the
extension hose and the drain hose
of the product must be fitted well
with an appropriate clamp as not to
come off and leak.
Electrical connection
Connect the machine to an earthed
outlet protected by a fuse of suitable
capacity.
Important:
• Connection should comply with
national regulations.
• Power cord plug must be within
easy reach after installation.
• The voltage and the allowed fuse
protection are specified in the
section “Technical Specifications”.
• The specified voltage must be equal
to your mains voltage.
• Connection via extension cords or
multi-plugs should not be made.
B A damaged power cable must be
replaced by a qualified electrician.
10 - EN
4 Initial preparations for washing
Sorting the laundry • Empty pockets and remove all
• Sort the laundry according to type foreign objects such as coins, pens
of fabric, color, and degree of soiling and paper clips. If possible, turn
and permissible water temperature. pockets out and brush.
Always follow the advice on the • Place small items like infants’
garment labels. socks and nylon stockings, etc.
in a laundry bag, pillow case or
something similar. This will also save
your laundry from getting lost.
• Place curtains in the machine with
Washing water Wash with Non machine Do not wash care. Remove curtain rails and
temperature sensitive, short washable
programmes. pullers.
• Fasten zippers, sew loose buttons
and mend rips and tears.
• Wash “machine washable” or “hand
washable” labelled products only
Bleach can be Do not use Dry-cleanable Do not
used bleach dry-clean with an appropriate programme.
• Do not wash colours and whites
together. New, dark coloured
cottons may release a lot of dye.
Wash them separately.
Suitable for Do not dry Dry Dry on a
• Tough stains must be treated
drier with drier horizontally hanger properly before washing. If you are
not sure, check with a dry cleaner.
• Use only dyes/colour changers and
lime removers suitable for machine
wash. Always follow the instructions
Hang without Can be ironed Can be Do not iron
on the packaging.
spinning with hot iron ironed with • Wash trousers and delicate clothes
warm iron
turned inside out.
Preparing clothes for washing • Keep laundry items made of Angora
Laundry items with metal attachments wool in the freezer for a few hours
such as, bras, belt buckles and metal before washing. This will reduce
buttons will damage the machine. pilling.
Remove metal attachments or place the
items in a clothing bag, pillow case, or Correct load capacity
something similar. • The maximum load capacity
depends on the type of laundry, the
degree of soiling and the washing
programme you wish to use.
C The machine adjusts the amount of
water according to the amount of
laundry placed inside.
C Please follow the information in
the "Programme Selection Table".
Washing results will degrade when
the machine is overloaded.
11 - EN
Following weights are given as Detergent, softener and other clean-
examples. ing agents
Laundry type Weight (gr.) Add detergent and softener before
starting the washing programme.
Bathrobe 1200 Never open the detergent dispenser
Napkin 100 drawer while the washing programme is
Duvet cover 700 running!
Bed Sheet 500 When using a programme without
Pillowcase 200 pre-wash, no detergent should be
put into the pre-wash compartment
Tablecloth 250 (Compartment no. I).
Towel 200 A programme without pre-wash should
Evening gown 200 be selected if a detergent bag or a
Underclothing 100 dispensing ball is going to be used.
You can place the detergent bag or
Men’s overalls 600 the dispensing ball directly among the
Men’s shirt 200 laundry in your machine.
Men’s pyjamas 500
Blouse 100 Choosing the detergent type
The type of detergent to be used
Loading door depends on the type and colour of
The door is locked during programme fabric.
operation. The door can be opened after • Use different detergents for coloured
some time following the programme and white clothes.
end. • Wash woolens with a special
• Open the door. detergent specifically for woolens.
• Place laundry items loosely in the • Use only detergents manufactured
machine. specifically for automatic washing
• Push the door until it clicks into machines.
place tightly. Ensure that no items
are caught in the door. Detergent quantity
The amount of washing detergent to
be used depends on the amount of
Detergents and softeners laundry, the degree of soiling and water
Detergent drawer hardness.
The detergent drawer is composed of
three compartments: • Do not use amounts exceeding
The detergent dispenser may be in two the quantities recommended on
different types according to the model of the package to avoid problems
your machine. of excessive foam, poor rinsing,
- (I) for prewash financial savings and finally,
- (II) for main wash environmental protection.
- (III) siphon • Use small amounts of detergent at a
– ( ) for softener suitable measure for small amounts
of laundry or for only slightly soiled
laundry.
• Use exact measures for highly
concentrated detergents.
12 - EN
Detergent Eliminating lime formation
quantity • When required, use only appropriate
for prewashing 1/2 measure lime removers developed specifically
for main washing 1 measure for washing machines and always
an additional 1/2 follow the instructions on the
with hard water package.
measure
Softener
Put the softener into the softener
compartment of the detergent
dispenser.
• Use the proportions recommended
on the packet.
• Never exceed the (> max <) level
marking; otherwise, the softener will
be wasted without being used.
• If the softener has lost its fluidity,
dilute dense softener with water
before placing it in the detergent
drawer.
Liquid detergent
When using liquid or gel washing
detergents, please note the following:
• The liquid detergent may leave
stains on your laundry if time delay
feature is selected.
• Do not use liquid detergent if you
want to wash using the time delay
feature.
• Do not use liquid detergent for the
main wash in a cycle with pre-wash.
• Use the detergent manufacturer’s
measuring cup and follow the
instructions on the package.
Starch
• Add liquid starch, powder starch
or the fabric dye into the softener
compartment as instructed on the
package.
• Never use fabric softener and starch
together in the same washing cycle.
• Wipe the inside of the drum after
using starch.
13 - EN
5 Selecting a Program and Operating Your Machine
Control panel
Figure 2
7 13 9 12 14
8 11 10
14 - EN
Display symbols appear. Press "Start/Pause/Cancel"
Figure 3 button (Figure 2-10) to start the
program.
Main programs
Depending on the type of textile, the
following main programs are available:
Each of these main programs comprise
13.a - Spin Speed Indicator of a complete washing process,
13.b - Temperature Indicator including washing, rinsing and, if
13.c - Spin Symbol required, spin cycles.
13.d - Temperature Symbol A When selecting the program you are
13.e - Remaining Time and going to use, always consider type
Delaying Time Indicator of fabric, color, degree of soiling and
13.f - Program Indicator permissible water temperature.
Symbols (pre-wash/main wash/ A Always select the lowest required
rinse/softener/spin) temperature. Higher temperature
13.g - Economy Symbol means higher power consumption.
13.h - Time Delaying Symbol C For further program details, see
13.i - Door Locked Symbol "Program Selection Table"
13.j - Start Symbol
13.k - Standby Symbol • Pamuklu (Cottons)
13.l - Auxiliary Function You can wash your durable clothes
Symbols with this program. Your laundry will
be washed with vigorous washing
Turning the machine on movements during a longer washing
Plug in your machine. Turn the tap on cycle. It is recommended for your
completely. Check if the hoses are cotton items (such as bed sheets,
connected tightly. Place the laundry duvet and pillowcase sets, bathrobes,
in the machine. Add detergent and underclothing, etc.).
softener. Press the “On/Off” button • Sentetik (Synthetics)
(Figure 2-14). You can wash your less durable clothes
on this program. Gentler washing
movements and a shorter washing cycle
Program selection is used compared to the “Cottons”
Select the appropriate program from program. It is recommended for your
the program table according to type, synthetic clothes (such as shirts,
amount and degree of soiling of the blouses, synthetic/cotton blended
laundry and washing temperatures. garments, etc.). For curtains and
Turn the Program Selection Knob (Figure lace, the “Synthetic 40” program with
2-12) to the program mode that you pre-wash and anti-creasing functions
wish to wash your laundry. selected is recommended. Detergent
The recommended temperature and should not be put in the pre-wash
spin speed for the selected program compartment. Less detergent should be
15 - EN
put in the main wash compartment as • Mix 40
loose knit fabrics (lace) foam too much You can use this program to wash
due to its meshed structure. cottons and synthetics together. There
• Yünlü (Woollens) is no need to sort them.
You can wash your machine-washable • Intensive
woolen garments on this program. Wash You can wash your durable and heavily
by selecting the proper temperature soiled clothes on this program. In this
according to the labels of your clothes. program, your clothes will be washed
It is recommended to use appropriate for a longer time and an extra rinse cycle
detergents for woolens. will be made compared to the “Cottons”
program. You can use it for your heavily
Additional programs soiled clothes that you wish to be rinsed
For special cases, there are also extra gently.
programs available: • Shirts
C Additional programs may differ You can use this program to wash the
according to the model of your shirts made of cotton, synthetic and
machine. synthetic blended fabrics.
• Bebek • Perde (Curtain)
Increased hygiene is provided by a You can use this program to wash
longer heating period and an additional your lace and curtains. It provides less
rinse cycle. It is recommended for baby creasing on lace and curtains thanks to
clothes and clothes worn by allergic the special spin profile of the program.
people. Less detergent should be put in the
• Elde Yıkama (Hand wash) main wash compartment as loose knit
You can wash your woolen/delicate fabrics (lace) foam too much due to its
clothes that bear “not machine- meshed structure.
washable” labels for which hand wash Never put detergent in the prewash
is recommended on this program. It compartment. Prewash is applied to
washes the laundry with very tender remove the particles (such as dust or
washing movements without damaging soot) on the lace/curtains, which can be
your clothes. removed easily.
• Express C It is recommended to use special
This program is used to wash lightly detergents for curtains in this
soiled and unstained cotton garments in program.
a short time.
• Express 14 Special programs
You can use this program to quickly For specific applications, select any of
wash a small number of lightly soiled the following programs:
and unstained cotton garments. E.g.: • Durulama (Rinse)
bathrobes, duvet covers, sport wear, This program is used when you want to
daily clothes and etc. used only once. rinse or starch separately.
• Darkcare • Sıkma+Pompa (Spin + Drain)
Use this programme to wash your This program spins with maximum
dark coloured laundry, or the coloured possible rpm in the default setting after
laundry that you do not want them get the water drains from the machine.
faded. This programme washes your C Use a lower spin speed for delicate
laundry with low mechanical movements laundries.
and at low temperature. We recommend
you to use liquid detergent or woolen Temperature selection
shampoo for dark coloured laundry. Whenever a new program is selected,
the temperature anticipated for that
16 - EN
program appears on the temperature
indicator (13b). Economy Symbol
To change the temperature, press Shows energy saving programs and
the temperature button (Figure temperature selections.
2-9). Temperature decreases in 10° As "Intensive" and "Hygiene" programs
increments. are long programs with higher
Cold selection is shown with “-” symbol. temperature selections to ensure
hygiene, “Economy” Symbol (Figure
3-13g) will not light up.
17 - EN
Program and consumption table
EN Auxiliary functions
Selectable temperature
Water Consumption (l)
Energy Consumption
Kırışık Azaltma
Max. Load (kg)
Max. Speed***
Programme (°C)
Hızlı Yıkama
Ön Yıkama
Rinse Hold
Rinse Plus
range °C
İlave Su
(kWh)
Pamuklu 90 8 61 2.70 1600 • • • • • • 90-Cold
Pamuklu 60** 8 59 1.36 1600 • • • • • • 90-Cold
Pamuklu 40 8 72 0.75 1600 • • • • • • 90-Cold
Yorgan 40 - 60 0.60 1000 60-40
Bebek 90 8 73 2.70 1600 * • 90-30
Sentetik 60 4 55 1.00 1000 • • • • • • 60-Cold
Sentetik 40 4 55 0.52 1000 • • • • • • 60-Cold
Mix 40 40 4 55 0.62 1000 • • • • • • 40-Cold
Yünlü 40 2 56 0.30 1000 • • • 40-Cold
Perde 40 2 67 0.50 800 * * * • 40-Cold
Elde Yıkama 30 1.5 40 0.25 1000 30-Cold
Express 90 8 70 2.00 1400 • • 90-Cold
Express 60 8 70 1.15 1400 • • 90-Cold
Express 30 8 80 0.20 1400 • • 90-Cold
Express 14 30 2 35 0.10 1400 • • 30-Cold
• : Selectable
* : Automatically selected, not cancellable.
** : Energy Label program (EN 60456)
*** If maximum spin speed of your machine is lower, selection may be made until
maximum spin speed.
- : See program description for maximum load.
C The auxiliary functions in the table vary according to the model of your machine.
C Water and power consumption and program duration differ from the table
subject to changes in water pressure, water hardness and temperature, ambient
temperature, type and amount of laundry, selection of auxiliary functions, and
changes in supply voltage.
C Program duration will be displayed on the screen of your machine according to
your selection.
18 - EN
• Hızlı Yıkama (Quick Wash)
Auxiliary functions With this function (11b), the wash time is
Auxiliary Function Selection Buttons shortened. "F2” symbol lights up on the
display.
• Use this function for smaller
amounts or slightly soiled laundries.
• Rinse Plus
When this function (11c) is selected,
washing and rinsing is performed with
plenty of water. "F3” symbol lights up on
the display.
• İlave Su (Plus water)
��� ��� ��� ��� When this function is selected, washing
• Depending on the program, you can and rinsing is made with plenty of water
select the desired auxiliary function in “Cottons”, “Synthetics”, “Delicates”
by pressing the buttons 11a, 11b, and “Woolens” programs.
11c,11d. C Use this function for delicate
• Select the required auxiliary laundries that crease easily.
functions before starting the C Whenever you select this auxiliary
program. function, load your machine with half
• Some combinations cannot be of the maximum laundry specified in
selected together. Ex.: Pre-wash the program table.
(Figure 2-11a) and Quick Wash • Kırışık Azaltma (Anti-Creasing)
(Figure 2-11b). With this function (11d), drum
• Symbol of the selected auxiliary movement will be lessened to prevent
function (Figure 3-13l) will light up. creasing and spinning speed is limited.
In addition, washing is carried out at a
Auxiliary function selection higher water level. "F4” symbol lights up
If an auxiliary function that should not on the display.
be selected together with a previously • Use this function for delicate
selected function is chosen, the first laundries that crease easily.
selected function will be cancelled and C Whenever you select this auxiliary
the last auxiliary function selection will function, load your machine with half
remain active. of the maximum laundry specified in
Ex.: If you want to select pre-wash first the program table.
and then quick wash, pre-wash will be
cancelled and quick wash will remain Time display
active. The display shows the time remaining
Auxiliary function that is not compatible for the program to complete while a
with the program cannot be selected. program is running. Time is displayed in
(see, “Program Selection Table”) hours and minutes as “01:30”.
• Ön Yıkama (Prewash)
When you select this function (11a), the
display will indicate "F1" symbol.
• A pre-wash is only worthwhile for
heavily soiled laundry. Without
pre-wash you save energy, water,
detergent and time.
• Pre-wash without detergent is
recommended for lace and curtains.
19 - EN
Time delay will fade. The Start symbol (Figure
With the “Time delay” function you can 3-13j) will light up.
delay the program start up to 24 hours. 4. The “:” in the middle of the displayed
Setting can be made in intervals of 30 time delay will start to flash.
minutes.
1. Open the loading door, place the Canceling the time delay
laundry inside and fill detergent If you want to cancel the time delay
drawer. countdown and start the program
2. Set the washing program, immediately:
temperature, spin speed and, 1. Press “Start/Pause/Cancel” button
if required, select the auxiliary (Figure 2-10). The “:” in the middle
functions. of the displayed time delay will stop
3. Press “Time delaying” buttons flashing.
“+” and “-” (Figure 2-8) to set 2. Start symbol (Figure 3-13j) will fade.
your desired time delay. The Time The standby symbol (Figure 3-13k)
delaying symbol (Figure 3-13h) will and the time delaying symbol (Figure
flash. 3-13h) will flash.
4. Press “Start/Pause/Cancel” button 3. Press time delaying button “-”
(Figure 2-10). Then the time delay (Figure 2-8) to decrease the desired
starts to count down. The Time time delay. Program duration after
delaying symbol (Figure 3-13h) will 30 minutes shall be displayed.
light up. The Start symbol (Figure 4. Press Start/Pause/Cancel Button
3-13j) will light up. (Figure 2-10) to start the program.
The “:” in the middle of the displayed
time delay will start to flash. Starting the Program
• More laundry may be loaded or 1. Press Start/Pause/Cancel button
taken out during the time delay (Figure 2-10) to start the program.
period. At the end of the time delay 2. The start symbol (Figure 3-13j)
countdown process, time delaying which indicates that the program
symbol (Figure 3-13h) fades and has started will light up.
the washing starts as the program 3. The door locks and the door locked
duration is displayed. symbol (Figure 3-13i) will light up.
4. The Symbol of the relevant step
Changing the delay time (prewash, main wash, rinse, softener
If you want to change the time during and spin) that the program has
the countdown: started from will light up (Figure
1. Press “Start/Pause/Cancel” button 3-13f).
(Figure 2-10). “ : “ in the middle of
the screen will stop flashing. The Progress of program
Standby symbol (Figure 3-13k) will The progress of a running program is
light up. The Time delaying symbol shown through a number of symbols on
(Figure 3-13h) will flash. The Start the screen.
Symbol (Figure 3-13j) will fade. • At the beginning of each program
2. Press “Time delaying” buttons “+” or step, the relevant symbol in the
“-” (Figure 2-8) to set your desired series of symbols will light up and
time delay. thus, at the end of the program,
3. Press “Start/Pause/Cancel” button all symbols will remain lit up. The
(Figure 2-10). The Time delaying symbol that lights up at the far right
symbol (Figure 3-13h) will light up. of the series of symbols indicates
The Standby symbol (Figure 3-13k) the step that is being carried out.
20 - EN
Pre-wash
When "prewash" auxiliary function is
selected, prewash symbol will light up to
indicate the beginning of prewash step.
Main wash
Main wash symbol will light up to
indicate that the main wash cycle has Selecting or canceling an auxiliary
started. function in pause mode
Rinse Auxiliary functions can be cancelled or
Rinse symbol lights up at the beginning selected in accordance with the step the
of the rinse step. program is at.
Softener
Softener symbol lights up at the Adding/removing laundry in pause
beginning of softener step. mode
Spin The door can be opened if the water
Spin symbol will light up at the level is suitable. The door locked symbol
beginning of the final spin, during “Spin” (Figure 3-13i) will light up until the door
and “Pump” special programs. is suitable for opening. This symbol will
• If the machine is not spinning, the fade out as soon as the door is allowed
program may be in rinse hold mode to open. Laundry may be added / taken
or the automatic spin correction out by opening the door.
system has been activated due
to an excessive unbalanced Door lock
distribution of laundry in the The Door Locked Symbol (Figure 3-13i)
machine. lights up when the loading door is
locked. This symbol will flash until the
Changing the selections after door is allowed to open. Do not force
the program has started the door at this stage. This symbol will
The selected spin speed and program fade out as soon as the door is allowed
temperature fade out. An empty frame to open. You may open the door after
appears. the symbol fades out.
When the “Program selection” button is
brought to the appropriate position, rpm Child-proof lock
and temperature data reappear. Protect the appliance from being
tampered by children by means of the
Switching the machine to child-proof lock. In this case, no change
standby mode can be made in the running program.
The machine is switched to standby C Your machine can be turned on
mode by pressing “Start/Pause/Cancel” and off with On/Off button while
button (Figure 2-10) momentarily. The the child-proof lock is activated. In
Standby symbol (Figure 3-13k) which this case, your machine will resume
indicates the machine is in standby its program with child-proof lock
mode lights up and the start symbol activated.
(Figure 3-13j) that shows the program The machine is switched to child-lock
has started and is still continuing fades by pressing the 2nd and 4th auxiliary
out. functions for 3 sec. “C:on” (Child-proof
lock is activated) label appears on the
display.
21 - EN
If you wish to spin when the machine is
in this mode:
Adjust the spin speed. Press “Start/
Pause/Cancel” button (Figure 2-10).
The program continues, pumps out the
water and spins. The Standby Symbol
The same symbol will also be displayed (Figure 3-13k) fades out and Start
whenever any button is pressed while Symbol (Figure 3-13j) lights up.
the machine is child-locked. If you want to discharge the water only
To deactivate the child-proof lock, without spinning:
press the 2nd and 4th auxiliary function Press “Start/Pause/Cancel” button
buttons for 3 sec. (Figure 2-10). The Standby symbol
“C:OFF” (Child-proof lock is deactivated) (Figure 3-13k) will fade. The Start
label appears on the screen. symbol (Figure 3-13j) will light up. The
program continues and only drains the
water.
End of program
When the program is finished, the
symbols of the relevant steps will remain
lit up and the auxiliary function, spin and
Ending the program through temperature data selected at the start-
canceling up of the program will remain selected.
“Start/Pause/Cancel” button (Figure “End” will appear on the display.
2-10) is pressed for 3 seconds to cancel
the program. Start symbol (Figure
3-13j) will flash during cancellation.
After cancellation, the symbol of the
corresponding step at which the
cancellation was made will remain lit and
“End” will appear on the screen.
22 - EN
6 Quick instructions for daily use
Preparation adding more laundry during a future
1. Turn the tap on completely. Check step only if the water level is low
that the hose is connected tightly. enough to open the loading door or
2. Place the laundry in the machine. if the temperature in the machine is
3. Add detergent and softener. low).
In order to add laundry after the
Starting start-up of the programme:
1. Press the “On/Off” button. 1. Press “Start/Pause/Cancel” button.
2. Select the programme and the 2. Open the loading door and put in
temperature. more laundry.
3. If desired (according to your 3. Close the loading door.
machine’s model): 4. Press “Start/Pause/Cancel” button.
– select any auxiliary function,
– adjust the spin speed, Programme is in rinse hold mode
– set the time delay, C This process is shown with the
4. Close the loading door. flashing spin symbol and the
5. Press “Start/Pause/Cancel” button. standby symbol which is lit up.
The display shows the time remaining If you wish to spin when the machine is
for the programme to complete if time in this mode:
delay is not set. 1. Adjust the spin speed.
The display shows the time remaining 2. Press “Start/Pause/Cancel” button.
for the programme to start if the time The programme continues, pumps
delay is set. out the water and spins.
6. Check if the Door Locked Symbol 3. The standby symbol fades out and
lights up on the screen. the start symbol lights up.
The Door Locked Symbol (Figure 3-2i) If you want to discharge the water
will light up if time delay is not set. without spinning:
The Door Locked Symbol (Figure 3-2i) 1. Press “Start/Pause/Cancel” button.
will fade if time delay is set. 2. The standby symbol fades out and
the start symbol lights up.
Cancelling a programme 3. The programme continues and only
1. Press and hold the “Start/Pause/ pumps out the water.
Cancel” button for about 3 seconds;
the Start symbol will start flashing. Re-spinning the laundry
2. The machine can discharge all The control system for an unbalanced
the water or can take in water for load can pause the spinning in cases
3 times at most to cool down the when the distribution of the laundry in
clothes and complete discharging the drum is not balanced.
process. If you want to re-spin the clothes:
1. Distribute the laundry in your
Adding more laundry machine for a balanced load.
• This is only possible under the 2. Select the spin programme.
following conditions: 3. Adjust the spin speed.
– during time delay,
C You may add or remove laundry After the programme is finished
during the time delay (until the Programme indicator symbols on
programme starts). At the beginning the screen will remain lit after the
of a washing cycle (machine allows programme is finished. “End” will appear
23 - EN
on the screen.
1. Open the loading door and take out
the laundry when the door locked
symbol on the display fades out.
2. Press the “On/Off” button.
3. Turn the water tap off.
4. Remove any folds in the rubber seal
on the loading door and check for
debris.
5. Leave the loading door and
detergent drawer open to dry.
24 - EN
7 Cleaning and care
Detergent drawer machine can cause rust stains. In
Remove any powder residue buildup in such cases:
the drawer. To do this; Clean the drum with a stainless steel
1. Press the dotted point on the cleaning agent. Never use steel wool
siphon in the softener compartment or wire wool.
and pull towards you until the
compartment is removed from the Outer cabinet and control
machine. panel
When necessary:
• Wipe the exterior panels of your
machine with soapy water or mild
detergent. Dry it with a soft cloth.
• Use only a soft and damp cloth to
clean the control panel.
C Never use a sponge or scrubbing
material. These will damage the
C If more than a normal amount of painted and plastic parts.
water and softener mixture starts to
gather in the softener compartment, Inlet water filters
the siphon must be cleaned. There is a filter at the end of each
2. Wash the dispenser drawer water intake valve at the back side of
and the siphon with plenty of the machine and also at the end of
lukewarm water in a washbasin. each water intake hose where they
Wear protective gloves or use an are connected to the tap. These filters
appropriate brush to avoid touching prevent the foreign substances and dirt
the residues in the drawer when in the water to enter into the machine.
cleaning. Filters should be cleaned as they get
3. Replace the drawer into its housing dirty.
after cleaning. Check if the siphon
is in its original location.
26 - EN
then resume the draining process.
• After draining process is completed,
replace the plug into the end of the
hose and fit the hose back into its
place.
27 - EN
8 Solution suggestions for problems
Cause Explanation / Suggestion
Programme cannot be started or selected.
Machine may have switched to Bring your machine to factory settings by turning
self protection mode due to an the programme selection knob. (see, Ending the
infrastructure problem (such as line programme through Cancelling)
voltage, water pressure, etc.).
Water in the machine.
There may be some water in your
machine when you receive it. This is
from the quality control process and is It is not harmful to your machine.
normal.
There is water coming from the bottom of the machine.
- Make sure that the seals of the water inlet hoses
There might be problems with hoses or are securely fitted.
- Tightly attach the drain hose to the tap.
the pump filter. - Make sure that the pump filter is completely
closed.
Machine does not fill with water
- Tap may be turned off. - Open the inlet water taps fully.
- Water inlet hose might be bent. - Flatten the water intake hose.
- Water inlet filter might be clogged. - Clean the water intake filter.
- The loading door may be ajar. - Close the loading door.
Machine does not discharge water.
- Water outlet hose might be clogged - Clean or flatten the hose.
or twisted. - Clean the pump filter.
- Pump filter may be clogged.
Machine vibrates or shakes.
- Machine feet might not be adjusted.
- Transportation safety bolts might have
not been removed. - Adjust the machine feet.
- There may be a small amount of - Remove the transportation safety bolts.
laundry in the machine. - Add more laundry to the machine.
- The machine may be overloaded - Reduce the amount of laundry in the machine or
or the clothes may be distributed balance the load by hand.
unevenly. - Ensure that nothing touches the machine.
- There machine might be touching a
solid surface.
Machine stops shortly after the programme starts.
Machine can stop temporarily due to It will resume operating when the voltage is back to
low voltage. the normal level.
The water being taken in is directly discharged.
Connect the water draining hose as described in
Improper position of the drain hose. the operation manual.
No water can be seen in the machine during washing.
This is not a problem. The water level
is not visible from the outside of the
machine.
28 - EN
The door is jammed.
- Water level might be above the lower
level of the door.
- Machine might be heating up the
water or it may be at the spinning - Run either the “Pump” or “Spin” programme.
cycle. - Wait until the process is over.
- Due to an electrical mechanism, - Wait until the process is over.
the door can only be opened a few
minutes after the programme has
stopped.
Machine fills with water when a process is cancelled.
It continuously spins. Remaining time does not count down. (On models with display)
- The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
- The laundry in the drum may be clustered
There may be an imbalance of laundry (bundled laundry in a bag). Laundry should be
in the machine. rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
Washing time takes longer than the time specified in the manual
29 - EN
It continuously washes. Remaining time does not count down.
In the case of a paused countdown - The machine will wait until there is sufficient
while taking in water: amount of water to avoid poor washing results due
- Timer will not countdown until the to lack of water. Then the timer will start to count
down.
machine is filled with the correct - Time will not count down until the selected
amount of water. (On models with temperature for the programme is attained.
display) - The automatic spin correction system might have
- Time might have gotten stuck during been activated due to the unbalanced distribution
heating step. (On models with display) of the laundry in the drum.
- The laundry in the drum may be clustered
In the case of a paused countdown at (bundled laundry in a bag). Laundry should be
the spinning step: rearranged and re-spun.
There may be an imbalance of laundry - No spinning is performed when the laundry is
in the machine. (On models with not evenly distributed in the drum to prevent any
display) damage to the machine and to its environment.
30 - EN
- Washing performance is poor: Oily stains appear on laundry.
- Washing performance is poor: Bad odour
- Such odours and bacteria layers are formed on
the drum as a result of continuous washing at
lower temperatures and/or in short programmes.
- Oily accumulations on the drum may - Leave the detergent dispenser drawer as well
have stuck to the laundry. as the loading door of the machine ajar after each
- Oily accumulations on the drum may washing. Thus, a humid environment favorable for
have stuck to the laundry. bacteria cannot be created inside the machine.
- Machine must be operated empty either at
60°C or 90°C programme with detergent every 6
months.
Colour of the clothes faded.
- Do not load the machine in excess
- Excessive laundry loaded into - Store detergent in a closed and dry location.
machine. - Do not keep them under high temperatures.
- Detergent may have gotten damp. - Select the proper programme and temperature
- A higher temperature might have according to the type and soiling degree of the
been selected. laundry.
It does not rinse well.
Clothes stiffened.
- If the water hardness is higher, using insufficient
amount of detergent can cause the laundry to
become stiff in time. Use appropriate amount of
- Insufficient amount of detergent used. detergent according to the water hardness.
- The detergent may have been - If detergent is put in the prewash compartment
placed into the wrong compartment; although prewash cycle is not selected, machine
the detergent may be mixed with the can take this detergent during rinsing or softener
softener. step.
- Do not mix the softener with detergent when
putting in the compartment.
- Wash and clean the drawer with hot water.
31 - EN
Clothes do not smell like the softener.
- If the water hardness is higher, using insufficient
amount of detergent can cause the laundry to
become stiff in time. Use appropriate amount of
- Insufficient amount of detergent used. detergent according to the water hardness.
- If detergent is put in the prewash compartment
- The detergent was placed into the although prewash cycle is not selected, machine
wrong compartment; the detergent can take this detergent during rinsing or softener
was mixed with the softener. step.
Do not mix the softener with detergent when
putting in the compartment.
Wash and clean the drawer with hot water.
Detergent residue in the dispensing drawer.
- Dry the detergent drawer before putting in
- Detergent may have been put in wet detergent.
dispenser drawer. - Store detergent in a closed and dry location.
- Detergent may have gotten damp. - Do not keep them under high temperatures.
- Water pressure might be low - The detergent dispenser outlet (holes) may have
- The detergent in the main wash a problem.
compartment might have gotten wet - There might be problems with the detergent
while taking in the prewash water.. dispenser valves.
- Detergent might be mixed with the - Do not mix the softener with detergent when
bleaching agent. putting in the compartment.
There is detergent left on the laundry.
- Excessive laundry loaded into
machine. - Do not load the machine in excess.
- Wrong programme and temperature - Select the proper programme and temperature
might have been selected. for the laundry to be washed.
- Wrong detergent may have been - Use wool detergents for woolens.
used.
There is too much foam
. - Use only automatic washing machine detergents
- You may not be using proper in your washing machine.
detergent for automatic washing - Use only sufficient amount of detergent.
machines. - Use only sufficient amount of detergent.
- Excessive amount of detergent may - Store detergent in a closed and dry location.
have been used. - Do not store in excessively hot places.
- Too much detergent may have been - Use smaller amounts of detergent for lace items.
used for a small amount of lightly soiled - If you put detergent in the prewash
laundry. compartment although you have not selected
- Detergent may have been stored a prewash cycle, the machine can take this
improperly. detergent during rinsing or softener step.
- Type of material being washed (lace - Too much softener was put in.
items will cause excessive foam due to The detergent dispenser is problematic. Water
their meshed structure). is siphoned (pulling the softener into the washer
- Detergent might have been put in the early) during the fill or rinse cycles.
wrong compartment. Valves are problematic.
- Softener being released early.
There is foaming over the detergent drawer
Mix 1 tablespoonful softener and ½ liter water
Too much detergent was used and pour into the main wash compartment of the
detergent drawer.
32 - EN
The plug might not be
plugged in the mains Check the plug.
outlet.
Machine does work. Fuse may have blown. Check the fuse.
Nothing is displayed on Electricity may be cut
the screen. Check the supply power.
off.
The “On/Off” button
might have not been Press this button.
pressed.
The machine did not
start after the program The front door may be
was selected and the
ajar.
“Start/Pause/Cancel”
button was pressed.
The Rinse Symbol
amongst the Program You can restart your machine by
Indicator Symbols is Water may have been pressing the “Start/Pause/Cancel”
flashing. (Subject to the cut off. button for a short time after ensuring
model of your machine, that the water is not cut off.
water cut-off symbol
may light up too)
33 - EN