Professional Documents
Culture Documents
RHC.PM6.5 RH
Technical data
Code RHC 3/2 RHC 33V RHCE 33V
Flow [l/min] 25 55 55
Working pressure pmax [bar] 500 500 500
Pilot ratio psi Main valve 4.5:1 2.5:1 2.5:1
Pre-discharging - 10:1 10:1
Pilot flow volume [cm³] 0.4 0.4 0.4
Tightening torque [Nm] 120 120 120
Material Total steel design, valve side bodypart, hardened, polished valve seat
Mounting Screwed-in intake hole of a body, observe dimension tolerance for thread core
hole D1.
Mounting position as desired
Connections A, B = main passage
Z = pilot oil connection
L = drain port not pressurised to the tank
Flow polarity B → A open; A → B in off position
(connection Z not pressurised) blocked drain-free, when no or lower pilot pres-
sure at B than at A A → B open, when the valve is blocked due to the pilot pres
sure at Z (see also pilot pressure pSt).
Opening pressure [bar] approx. 0.5 (B → A)
p
Pilot pressure pSt [bar] For pilot-operation pSt = ψA + 2.5
(orientation calculation)
∆
to keep it open pSt ≈ pB + p + 4.5
y
y see pilot ratio
pA = pressure at A
pB = pressure at B
∆p/Q performance curves (subsequently)
Pressure fluid Hydraulic oil as per DIN 51 524 TI.1 to 3 ISO VG 10 to 68 as per DIN 51 519
6 Viscosity range
Optimal operation
min. approx. 4; max. approx. 1500 mm²/s
approx. 10...500 mm²/s
Also suitable for biodegradable pressure fluids types HEPG (polyalkylene
glycol) and HEES (synth. Ester) at operating temperatures up to approx. 70°C.
Environmental temperature [°C] approx. -40...+80, oil: -25...+80,
watch out for viscosity range Starting temperature permitted up to -40°C, observe
starting viscosity,if the equilibrium temperature in final operation is at least 20K
higher. Biodegradable pressure fluids: observe manufacturing specifications.
While considering the seal compatibility not over +70°C.
Ordering code
RHC
Hydraulic Flow / design
pilot-operated
check valve
3/2 4.5 : 1 - 25
33V 2.5 : 1 10 : 1 55
E33V 2.5 : 1 10 : 1 55
RHC.PM6.5 RH
l1
ww l2 O-ring l3
Ød1
Ød2
G4h
20°
6
l1
l2
ww l3 l4
l5
O-ring 1
80-90
Shore
G
O-ring 2
Control spool sealed
Type G l1 l2 l3 l4 l5 L1 L2 D1 D2 D3 D4 D5 t T1 T2 T3 T4 T5 WW
RHC.PM6.5 RH
Type G l1 l2 l3 l4 l5 L1 L2 L3 D1 D2 D3 D4 D5 D6 D7 D8 T1 T2
6 RHCE 33V M27x2 59 41.5 14 16 7.5 16 36.5 52 12 16 22.7 23 23.7 24 32 12 59 19
Type T3 T4 T5 T6 T7 T8 WW O-ring1 O-ring2 O-ring3 Sealing ring max. tight. torque (Nm)
RHCE 33V 46 38.5 37.5 29 25 0.5 10 15.3x2.4 18.72x2.62 18x2.5 27x32x2 120
RHC.PM6.5 RH