Professional Documents
Culture Documents
(Mechanical properties)
Properties of Materials
(Sifat / Karakteristik Material)
1. Mechanical Properties (Sifat Mekanik):
• Elastic properties
• Plastic properties
F
=
Ao
Ski lift (photo courtesy P.M. Anderson)
• Simple shear: drive shaft
Fs
=
Ao
Note: = M/AcR here.
5
OTHER COMMON STRESS STATES (1)
• Simple compression:
Ao
Note: compressive
Balanced Rock, Arches structure member
National Park
(photo courtesy P.M. Anderson) ( < 0 here).
6
OTHER COMMON STRESS STATES (1)
6
OTHER COMMON STRESS STATES (2)
• Bi-axial tension: • Hydrostatic compression:
z > 0 h< 0
7
Concept of Stress and Strain Konsep Tegangan dan
(Static load) Regangan (Beban statik)
Bila beban statik diberikan
When a static load is applied pada material, maka
to a material, the material will material akan berubah
change its shape (deform). If bentuk (berdeformasi).
we follow the degree of Jika kita mengikuti besar
deformation as a function of F deformasi sebagai fungsi
load, we will get information beban, maka kita akan
about the "behaviour" of the memperoleh informasi
material. Dl/2 mengenai "perilaku" dari
material.
lf l0
A0
F
Loads (F) are expressed in force Beban (F) dinyatakan dalam
units, i.e. ??? satuan beban, yaitu ???.
Stress () : the intensity of the Tegangan () : intensitas
internally distributed forces that beban yang didistribusikan di
resist a change in the form of a dalam material, yang
body. menghambat perubahan
bentuk. = F / A0 [satuan ??]
= F / A0 [unit ??]
Deformasi digunakan sebagai
Deformation is used as a general
istilah umum untuk perubahan
term to indicate the change in
bentuk dari sebuah benda /
form of the body.
material.
Strain (e): the change per unit
Regangan (e): perubahan
length in a linear dimension of a
panjang dari sebuah benda.
body.
Deformasi elastik:
• Deformasi dimana tegangan dan
regangan berbanding lurus.
• Tidak permanen → ketika beban
dilepas, spesimen akan kembali ke
bentuk awal.
ELASTIC DEFORMATION
1. Initial 2. Small load 3. Unload
bonds
stretch
return to
initial
F
2
Elastic Deformation:
• Hooke's law applied:
15
Tensile Properties
• Yield strength y : the stress level where
plastic deformation begins, or where the
phenomenon yielding occur.
• This is sometimes called proof stress,
which is chosen as that causing a
permanent strain of 0.002.
• Kekuatan luluh, y: tegangan dimana
deformasi plastis mulai atau ketika
fenomena luluh terjadi.
• Kadang-kadang disebut sebagai proof
stress, yaitu tegangan yang menyebabkan
regangan sebesar 0.002.
YIELD STRENGTH: COMPARISON
y(ceramics)
>>y(metals)
>> y(polymers)
Room T values
Based on data in Table B4,
Callister 6e.
a = annealed
hr = hot rolled
ag = aged
cd = cold drawn
cw = cold worked
qt = quenched & tempered
17
Tensile strength:
maximum stress
(~100 - 1000 MPa) Fracture
• Tensile strength: the stress at Strength
the maximum on the
engineering stress-strain
curves. This corresponds to
the maximum stress that can
be sustained by a structure.
• At maximum stress, a small
constriction or neck begins, “Necking”
and this is called necking.
• Fracture / rupture strength:
stress at fracture.
TENSILE STRENGTH
• Maximum possible engineering stress in tension.
(l f − l0 )
%elongation = 100
l0
( Af − A0 )
% AR = 100
A0
DUCTILITY, %EL
L f − Lo
• Plastic tensile strain at failure: %EL = x100
Lo
Ao − A f
• Another ductility measure: %AR = x100
Ao
• Note: %AR and %EL are often comparable.
--Reason: crystal slip does not change material volume.
--%AR > %EL possible if internal voids form in neck.
20
• The importance of ductility:
– An indication of a degree
to which a structure will
deform plastically before
fracture.
– Specifies the degree of
allowable deformation
during fabrication.
• Terms of ductile and brittle
• Kegunaan nilai keuletan:
materials.
– Menunjukkan sejauh mana sebuah
struktur dapat berdeformasi plastis
sebelum patah.
– Menentukan derajat deformasi
yang diizinkan selama fabrikasi.
• Istilah material ulet and getas.
TOUGHNESS
• Energy to break a unit volume of material
• Approximate by the area under the stress-strain
curve.
Engineering smaller toughness (ceramics)
tensile larger toughness
stress, (metals, PMCs)
smaller toughness-
unreinforced
polymers
21
Toughness: the ability of
materials to absorb energy up
to fracture.
• For a material to be tough, it
must display both strength
and ductility.
• Unit ???
Ketangguhan: kemampuan
material menyerap energi
hingga patah.
• Material disebut tangguh bila
memiliki baik kekuatan dan
keuletan.
Fracture surface of tensile specimens
Material Description
mild steel cup-cone, silky
wrought iron ragged, fibrous
gray, flat,
cast iron
granular
cold-worked or heat-treated
"star fracture"
materials
Ductile Fracture
Al
Steel
Comparison of tensile properties of materials
• Position of specimen in
Izod methode
Impact Testing
• One of the primary functions of Charpy and Izod tests is to
determine whether or not material experiences a ductile-to-brittle
transition, with decreasing temperature.
Thermal Properties
•Oxidation: M → M n+ + n e-
•Reduction: 2H + + 2 e- → H2
O2 + 4H + + 4 e- → 2H2O
O2 + 2H2O + 4 e- → 4 OH –
• Example:
Fe + ½ O2 + H2O → Fe 2+ + 2 OH – → Fe(OH)2
2Fe(OH)2 + ½ O2 + H2O → Fe(OH)3
Chemical Properties
• Corrosion rate: the rate of • Laju korosi: laju penghilangan
material removal as a material akibat reaksi kimia.
consequence of the chemical
• Dinyatakan sebagai laju
action.
penetrasi korosi
• Is expressed as corrosion
penetration rate (CPR). CPR = KW / rAt
• W = kehilangan berat setelah
CPR = KW / rAt
ekspos selama t, r = berat jenis
• W = weight loss after exposure material, A = luas spesimen yang
time t, r = density of material, A = diekspos, K = konstanta.
exposed specimen area, K = a
• Satuan: mpy (mils per year) atau
constant.
mm/yr. 1 mils = 0.001 in.
• Unit: mpy (mils per year) or
mm/yr. 1 mils = 0.001 in.
Chemical Properties
• Passivity. Some normally active • Pasivitas. Beberapa material
materials, under particular yang biasanya aktif, dalam
environmental conditions, lose kondisi lingkungan tertentu
their chemical reactivity and dapat kehilangan reaktivitas
become extremely inert. This is kimianya dan menjadi
termed passivity. , e.g: Al, Fe, sangat inert. Hal ini disebut
Cr, Ni, Ti. pasivitas. contohnya: Al, Fe,
Cr, Ni, Ti.
• Passivity is resulted from
formation of highly adherent • Pasivitas disebabkan oleh
and thin oxide film on the terbentuknya lapisan tipis
metal surface. oksida yang menempel
sangat kuat di permukaan
logam.