SCANIA COOLANT FILTER
To reduce the risk of the cooling system clogging If there are signs of the radiator clogging up ona
up (e.g. the radiator) a Scania coolant filter may be ‘truck that is to be equipped with a coolant filter,
installed. The filter contains anti-corrosive in the stem first has to be cleaned according
e@ form of powder. to description on page 4.
Installation is illustrated by figures 1 and 2. The filter must be changed at M6 maintenance or
with 60 000 km intervals.
1.T pipe
2.inlet hose
3.Elbow union
4.Return hose
5.Filter
6-Filter head
7.Bracket
&.Tap
1.T pipe
2.inlet hose
3.Elbow union
4.Return hose
S.Filter
6-Filter head
7.Bracket
@Tap
Fig 2. Installation, T trucks
156 OY 32Parts for conversion Fitting of bracket (350575)
Conversion kit 561624 consists of: = Drill two holes in panel behind bumper on GPR
trucks or bracket behind bumper on T trucks,
Part name PartNo. Qty Bracket 350575 may be used as drilling pattern.
Bracket 350575 1 See figures 3 and 4.
Nut (Meme) 807410 2
‘Screw (M65,8x25) 808296 2 = Fitbracket 7.
Filter head 3444291 On GPR trucks it is possible to reach positions
‘Screw (U6S,3/8"x25) 806360 4 for nuts through the hole for extra lights.
Tap 344250 2
Filter 3509861
Tpipe 344670 1
Hose (5/8",L = 1410) 189706 2
Elbow union 1392951
Hose clamp. 796353 6
Fully bent clamp 904583 4
‘Screw (ME5,6x20) 901992 2
Washer (BRB6,4x12) 802995 2
Nut (MeMmé) 302955 2
strap 2292491
2 SCANIA service 2-84.08 28 GTEN- Apply thread seal to threads of taps and back
Up taps in filter head to obtain correct direction
for hose connections. See figures 5 and 6.
- Back up filter head 6 against bracket and fit
filter cartridge 5.
Fig5
2-84.08 28 GTEN SCANIA serviceHose connections
+ Drain coolant.
~ Remove flange pipe under radiator (by- pass
line).
~ On trucks with charge-air cooling the boss on
the flange pipe, where the filter is to be connec-
ted, has to be cut off by approx. 9 mm, to pre-
vent the elbow union from being fitted too
close to the charge-air pipe.
> Drill and tap hole for elbow union 3 with thread
NPTF 3/8" - 18.
- Apply thread seal to thread of elbow union and
back it up in the hole, so that the hose connec-
tion points aft to the left side of the truck.
+ Fit flange pipe.
- Cut hose between thermostat housing and
heater package and remove a hose length of
approx. 100 mm. Fit T pipe 1 with the smaller
angle towards the centre of the truck.
= Cut hoses 2 and 4 to correct lengths and
connect them.
GPR:
Clamp inlet hose in two places to panel behind
bumper. Retain return hose with tie-wrap and
suitable hose. See figure 1.
t
Clamp both hoses together on bottom flange on
bumper. See figure 2
~ Note. itis important that the hoses are connec-
ted so that the flow direction through the filter
is correct. The filter head is marked "IN" and
“OUT”. The hose from the cab heater line must
be connected to “IN and the hose to the by-
ass line to "OUT". See figures 5 and 6.
4 SCANIA service
~ Fill with coolant. If there is a content of at least
25 % glycol (with inhibitor) in the coolant, no
anti-corrosive is necessary in addition to what is,
contained in the filter.
Make a test run and check that the filter be-
comes hot, which is a sign that the coolant is
circulating correctly.
Cleaning of cooling system
Drain litres from the cooling system.
= _ Fill with 5 litres of Scania cleaning agent
584026.
> Copy and attach warning label as illustrated
- _ Truckis then to be operated as usual during 3 to
weeks.
= Then drain cooling system by removing one of
the hoses where connected to the radiator.
Note. Beware of scalding accidents when the
coolant is hot.
= _ Restore the hose and fill cooling system with
clean, warm water.
~ Run engine until water is hot enough for
thermostat to open.
+ Drai
according to specification in group 0,
ricants, fluids".
water and fill cooling system with coolant
"Oils, lub-
‘The cooling system filled with
SCANIA CLEANSING AGENT FORCOOLING SYSTEM
Date. by
MANOUNG
Use protective glasses and protective gloves when handling
the product
Splashes in the eyes: Rinse with gentle water flow. Contact
eyespecials.
_| Splashes on the skin: Wash generously with water,
ken internally: Do not force to throw up, Drink water or
Joangerous to consume,
Keep out of reach of children.
[Contains sodiumnitrite and borate,
Warning label
2-84.08 28. GT EN
MiG 1984:35967