Professional Documents
Culture Documents
2 Page 1
Table of Contents
Notifications Summary............................................................................................................................................................1
Table of Contents.................................................................................................................................................................... 2
Pre-analysis Checks.................................................................................................................................................................3
Building Data....................................................................................................................................................................... 3
Seismic Parameters.............................................................................................................................................................3
Seismic Response Spectrum Properties:.........................................................................................................................3
SNI1726 Tepki Spektrumu; Soil=SB; R=7; I=1; Sds=0.267; Sd1=0.067............................................................................3
Load Combinations.............................................................................................................................................................4
Vertical Load Cases.........................................................................................................................................................4
Lateral Load Cases...........................................................................................................................................................5
Materials:............................................................................................................................................................................ 5
Concrete Grades:............................................................................................................................................................5
Steel Grades:................................................................................................................................................................... 5
INTERSTOREY STRENGTH IRREGULARITY CHECK (Weak Storey).........................................................................................5
Earthquake Direction: 1 (Angle From X 0.00 degrees)..................................................................................................5
Earthquake Direction: 2 (Angle From X 90.00 degrees)................................................................................................5
Column and Beam Inertia Center........................................................................................................................................6
Beam Loads............................................................................................................................................................................. 7
Slab Additional Dead Loads...................................................................................................................................................32
Beam Wall Loads................................................................................................................................................................... 33
Post-analysis Checks.............................................................................................................................................................34
INTERSTOREY STIFFNESS IRREGULARITY CHECK (Soft Storey):..........................................................................................34
INTERSTOREY MASS IRREGULARITY CHECK:......................................................................................................................35
TORSION IRREGULARITY CHECK:.......................................................................................................................................35
RELATIVE STOREY DRIFT CHECK:.......................................................................................................................................36
SECOND ORDER EFFECTS REQUIREMENT CHECK:.............................................................................................................37
MEMBER EFFECTIVE SECTION STIFFNESS FACTORS..........................................................................................................38
STOREY MASSES AND WEIGHTS:.......................................................................................................................................38
STOREY CENTER OF GRAVITY TABLE.................................................................................................................................39
EARTHQUAKE FORCES:......................................................................................................................................................39
SEISMIC OVERTURNING CHECK:........................................................................................................................................40
STRUCTURAL IRREGULARITIES:.........................................................................................................................................41
SUMMARY REPORT:..........................................................................................................................................................41
Eigenvalue/EQ Analysis Results............................................................................................................................................43
Analysis Model Echo Report.................................................................................................................................................45
Storey Displacements...........................................................................................................................................................51
Axial Load Comparison Report..............................................................................................................................................60
Pre-analysis Checks
Building Data
Number of Storeys =8
Number of Effective Storeys =8
Number of Rigid Basements =0
Seismic Parameters
Analysis Type = Equivalent Static Load Analysis
t (sec) S(t)
0.000 0.0381
0.050 0.0381
0.250 0.0381
0.262 0.0364
0.276 0.0345
0.297 0.0321
0.323 0.0295
0.355 0.0268
0.394 0.0242
0.438 0.0218
0.487 0.0195
0.543 0.0175
0.604 0.0158
0.672 0.0142
0.745 0.0128
0.824 0.0117
0.909 0.0117
1.000 0.0117
1.000 0.0117
1.072 0.0117
1.141 0.0117
1.243 0.0117
1.386 0.0117
1.576 0.0117
1.820 0.0117
2.125 0.0117
2.497 0.0117
2.944 0.0117
3.472 0.0117
4.087 0.0117
4.797 0.0117
5.608 0.0117
6.527 0.0117
7.561 0.0117
8.716 0.0117
10.000 0.0117
Load Combinations
No Combination D Dc L Lc LS1 LS2 Ez Ex+ Ex- Ey+ Ey-
1 D*F 1.20 .00 .00 .00 .00 .00 .00 .00 .00 .00 .00
2 D+L *F 1.20 .00 1.60 .00 .00 .00 .00 .00 .00 .00 .00
3 D+L *F1 1.20 .00 1.05 .00 .00 .00 .00 .00 .00 .00 .00
4 D+LS1 *F 1.20 .00 .00 .00 1.60 .00 .00 .00 .00 .00 .00
5 D+LS2 *F 1.20 .00 .00 .00 .00 1.60 .00 .00 .00 .00 .00
6 Dc+Lc+Ex++Ez .00 1.00 .00 1.00 .00 .00 1.00 1.00 .00 .00 0.30
7 Dc+Lc-Ex++Ez .00 1.00 .00 1.00 .00 .00 1.00 - 1.00 .00 .00 - 0.30
8 Dc+Lc+Ex-+Ez .00 1.00 .00 1.00 .00 .00 1.00 .00 1.00 0.30 .00
9 Dc+Lc-Ex-+Ez .00 1.00 .00 1.00 .00 .00 1.00 .00 - 1.00 - 0.30 .00
10 Dc+Lc+Ey++Ez .00 1.00 .00 1.00 .00 .00 1.00 .00 0.30 1.00 .00
11 Dc+Lc-Ey++Ez .00 1.00 .00 1.00 .00 .00 1.00 .00 - 0.30 - 1.00 .00
12 Dc+Lc+Ey-+Ez .00 1.00 .00 1.00 .00 .00 1.00 0.30 .00 .00 1.00
13 Dc+Lc-Ey-+Ez .00 1.00 .00 1.00 .00 .00 1.00 - 0.30 .00 .00 - 1.00
14 Dc+Ex++Ez .00 0.90 .00 .00 .00 .00 - 1.00 1.00 .00 .00 0.30
15 Dc-Ex++Ez .00 0.90 .00 .00 .00 .00 - 1.00 - 1.00 .00 .00 - 0.30
16 Dc+Ex-+Ez .00 0.90 .00 .00 .00 .00 - 1.00 .00 1.00 0.30 .00
17 Dc-Ex-+Ez .00 0.90 .00 .00 .00 .00 - 1.00 .00 - 1.00 - 0.30 .00
18 Dc+Ey++Ez .00 0.90 .00 .00 .00 .00 - 1.00 .00 0.30 1.00 .00
19 Dc-Ey++Ez .00 0.90 .00 .00 .00 .00 - 1.00 .00 - 0.30 - 1.00 .00
20 Dc+Ey-+Ez .00 0.90 .00 .00 .00 .00 - 1.00 0.30 .00 .00 1.00
21 Dc-Ey-+Ez .00 0.90 .00 .00 .00 .00 - 1.00 - 0.30 .00 .00 - 1.00
22 D+Ex++Ez 1.00 .00 .00 .00 .00 .00 1.00 1.00 .00 .00 0.30
23 D-Ex++Ez 1.00 .00 .00 .00 .00 .00 1.00 - 1.00 .00 .00 - 0.30
24 D+Ex-+Ez 1.00 .00 .00 .00 .00 .00 1.00 .00 1.00 0.30 .00
25 D-Ex-+Ez 1.00 .00 .00 .00 .00 .00 1.00 .00 - 1.00 - 0.30 .00
26 D+Ey++Ez 1.00 .00 .00 .00 .00 .00 1.00 .00 0.30 1.00 .00
27 D-Ey++Ez 1.00 .00 .00 .00 .00 .00 1.00 .00 - 0.30 - 1.00 .00
28 D+Ey-+Ez 1.00 .00 .00 .00 .00 .00 1.00 0.30 .00 .00 1.00
29 D-Ey-+Ez 1.00 .00 .00 .00 .00 .00 1.00 - 0.30 .00 .00 - 1.00
Vertical Load Cases
D = Sabit Yükler
Dc = Sabit Yükler (Çatlamış)
L = Hareketli Yükler
Lc = Hareketli Yükler (Çatlamış)
LS1 = Sasirtmali H. Yükler 1
LS2 = Sasirtmali H. Yükler 2
Ez = Düşey Earthquake
Gc and Qc load cases uses cracked sections for being combined with seismic load cases.
G and Q load cases uses uncracked sections for being combined with vertical load combinations.
Materials:
Concrete Grades:
Fck Fcd Fctd E
(N/mm2) (N/mm2) (N/mm2) (N/mm2)
Columns C35/45 35.00 23.33 1.38 34000.0
Walls C35/45 35.00 23.33 1.38 34000.0
Beams C35/45 35.00 23.33 1.38 34000.0
Slabs C35/45 35.00 23.33 1.38 34000.0
Ribbed Slabs C35/45 35.00 23.33 1.38 34000.0
Foundations C25/30 25.00 16.67 1.17 31000.0
Steel Grades:
Fyk Fyd E
(N/mm2) (N/mm2) (N/mm2)
Columns Grade 500 (Type 2) 500.00 434.78 200000.0
Walls Grade 500 (Type 2) 500.00 434.78 200000.0
- Web Longitudinal Grade 500 (Type 2) 500.00 434.78 200000.0
- Web Horizontal Grade 500 (Type 2) 500.00 434.78 200000.0
Beams Grade 500 (Type 2) 500.00 434.78 200000.0
Slabs Grade 500 (Type 2) 500.00 434.78 200000.0
Ribbed Slabs Grade 500 (Type 2) 500.00 434.78 200000.0
Foundations Grade 410 (Type 2) 410.00 356.52 200000.0
Links Grade 500 (Type 2) 500.00 434.78 200000.0
Beam Loads
1B1 (500.0/600.0 mm L= 8000.00 mm)
Adjustment Loads: g= -1.21 kN/m
Partial Distributed Loads (m, kN/m):
1S13 x= 0.00 4.00 8.00
g= 0.00 32.00 0.00
q= 0.00 8.00 0.00
Reactions: GI= 87.8 kN QI= 16.0 kN GJ= 87.8 kN QJ= 16.0 kN
Note:
Whole structure is considered as a single integrated 3D model for the analysis.
Therefore, reactions transferred by the secondary beams are considered naturally to the main
beams.
Post-analysis Checks
INTERSTOREY STIFFNESS IRREGULARITY CHECK (Soft Storey):
hi : Storey Height
Δ : Relative Storey Drift (δ column,top - δ column,bot)
Upper Storey Ratio : Δ i+1 / Δ i
Δ ave-3 : Ave (Δ i-1, i, i+1)
Upper 3 Storey Ratio : Δ ave-3 / Δ i
Storey: 2 3.500 7.3397E-04 0.001 9.7554E-04 2.7873E-04 1.131 ≥ 0.700 √ 1.171 ≥ 0.80 √
Storey: 1 4.500 6.3760E-04 0.001 8.9784E-04 1.9952E-04 1.397 ≥ 0.700 √ 1.547 ≥ 0.80 √
Attention: Dir 1 Due to Seismic Zone, Irregularities and/or Building Height Limits Equivalent Static Load Analysis Method cannot be used. X
Storey: 8 0.007 0.010 5.6535E-04 0.001 8.2283E-04 1.313 > 1.20 6.0
Storey: 7 0.006 0.009 8.4996E-04 0.001 0.001 1.172 ≤ 1.20 ---
Storey: 6 0.005 0.007 9.1154E-04 0.001 0.001 1.174 ≤ 1.20 ---
Storey: 5 0.004 0.006 9.4286E-04 0.001 0.001 1.177 ≤ 1.20 ---
Storey: 4 0.003 0.005 9.3705E-04 0.001 0.001 1.179 ≤ 1.20 ---
Storey: 3 0.002 0.003 8.8683E-04 0.001 0.001 1.181 ≤ 1.20 ---
Storey: 2 0.001 0.002 7.8037E-04 0.001 9.5507E-04 1.183 ≤ 1.20 ---
Storey: 1 7.1516E-04 0.001 7.1516E-04 0.001 8.7389E-04 1.182 ≤ 1.20 ---
Attention: Dir 2 Due to Seismic Zone, Irregularities and/or Building Height Limits Equivalent Static Load Analysis Method cannot be used. X
Dir 1: Second Order Effects are considered using code based slenderness methods. √
Dir 2: Second Order Effects are considered using code based slenderness methods. √
Storey h m mr2 G Q W
(m) (t) (t.m2) (kN) (kN) (kN)
8 3.500 1448.728 3.148E+05 13657.6 1848.0 14212.0
7 3.500 1276.505 2.310E+05 11942.7 1932.8 12522.5
6 3.500 1276.505 2.310E+05 11942.7 1932.8 12522.5
5 3.500 1276.505 2.310E+05 11942.7 1932.8 12522.5
4 3.500 1276.505 2.310E+05 11942.7 1932.8 12522.5
Storey Bx Xg ex By Yg ey
(m) (m) (%) (m) (m) (%)
8 44.000 22.180 5.00 24.000 11.190 5.00
7 44.000 22.217 5.00 24.000 11.535 5.00
6 44.000 22.217 5.00 24.000 11.535 5.00
5 44.000 22.217 5.00 24.000 11.535 5.00
4 44.000 22.217 5.00 24.000 11.535 5.00
3 44.000 22.217 5.00 24.000 11.535 5.00
2 44.000 22.217 5.00 24.000 11.535 5.00
1 44.000 22.245 5.00 24.000 11.261 5.00
EARTHQUAKE FORCES:
Earthquake forces are calculated using R = 7.0.
Storey Fx Fy Fz Mz
(kN) (kN) (kN) (kN.m)
8 2497.3 0.0 0.0 -2996.8
7 1728.0 0.0 0.0 -2073.6
6 1490.8 0.0 0.0 -1789.0
5 1253.7 0.0 0.0 -1504.4
4 1016.5 0.0 0.0 -1219.8
3 779.3 0.0 0.0 -935.2
2 542.1 0.0 0.0 -650.5
1 322.6 0.0 0.0 -387.2
Total 9630.4 0.0 0.0 -11556.5
Storey Fx Fy Fz Mz
(kN) (kN) (kN) (kN.m)
8 2497.3 0.0 0.0 2996.8
7 1728.0 0.0 0.0 2073.6
6 1490.8 0.0 0.0 1789.0
5 1253.7 0.0 0.0 1504.4
4 1016.5 0.0 0.0 1219.8
3 779.3 0.0 0.0 935.2
2 542.1 0.0 0.0 650.5
1 322.6 0.0 0.0 387.2
Storey Fx Fy Fz Mz
(kN) (kN) (kN) (kN.m)
8 0.0 2524.8 0.0 5554.6
7 0.0 1721.4 0.0 3787.0
6 0.0 1485.1 0.0 3267.2
5 0.0 1248.8 0.0 2747.4
4 0.0 1012.6 0.0 2227.6
3 0.0 776.3 0.0 1707.9
2 0.0 540.0 0.0 1188.1
1 0.0 321.4 0.0 707.1
Total 0.0 9630.4 0.0 21186.8
Storey Fx Fy Fz Mz
(kN) (kN) (kN) (kN.m)
8 0.0 2524.8 0.0 -5554.6
7 0.0 1721.4 0.0 -3787.0
6 0.0 1485.1 0.0 -3267.2
5 0.0 1248.8 0.0 -2747.4
4 0.0 1012.6 0.0 -2227.6
3 0.0 776.3 0.0 -1707.9
2 0.0 540.0 0.0 -1188.1
1 0.0 321.4 0.0 -707.1
Total 0.0 9630.4 0.0 -21186.8
OVERTURNING EFFECTS:
Storey h F1 Ma1 F2 Ma2
(m) (kN) (kN.m) (kN) (kN.m)
Storey: 8 29.000 2497.3 72422.6 2524.8 73219.4
Storey: 7 25.500 1728.0 44064.3 1721.4 43894.6
Storey: 6 22.000 1490.8 32798.4 1485.1 32672.0
Storey: 5 18.500 1253.7 23192.6 1248.8 23103.3
Storey: 4 15.000 1016.5 15247.2 1012.6 15188.4
Storey: 3 11.500 779.3 8961.9 776.3 8927.4
Storey: 2 8.000 542.1 4337.0 540.0 4320.3
Storey: 1 4.500 322.6 1451.9 321.4 1446.3
Total 202475.9 202771.8
Overturning Check: Dir 1 ... Mp1 / Ma1 = 2235031.1 / 202475.9 = 11.0385 ≥ 2.0 OK √
Overturning Check: Dir 2 ... Mp2 / Ma2 = 1174900.7 / 202771.8 = 5.7942 ≥ 2.0 OK √
STRUCTURAL IRREGULARITIES:
Plan Irregularities
Torsional Irregularities : -EXIST-
Extreme Torsion Irregularity : -EXIST-
Discontinuities in Floor Diaphragm : -NONE-
Existance of Re-entrant Corners : -NONE-
Non-parallel Axes to Earthquake Direction : -NONE-
Vertical Irregularities
Interstorey Strength Irregularity (Weak Storey) : -NONE-
Extreme Interstorey Strength Irregularity : -NONE-
Interstorey Stiffness Irregularity (Soft Storey) : -NONE-
Extreme Interstorey Stiffness Irregularity : -NONE-
Interstorey Mass Distribution Irregularity : -NONE-
Discontinuities in Vertical Load Bearing Members : -NONE-
Existance of Re-entrant Storeys : -NONE-
Discontinuity of Lateral Load Bearing Members : -NONE-
SUMMARY REPORT:
Strength Irregularity does not exists in the building. √
Due to Seismic Zone, Irregularities and/or Building Height Limits Equivalent Static Load Analysis Method cannot be used.
SUMMARY REPORT:
Attention: Dir 1 Due to Seismic Zone, Irregularities and/or Building Height Limits Equivalent Static Load Analysis Method cannot be used.
Attention: Dir 2 Due to Seismic Zone, Irregularities and/or Building Height Limits Equivalent Static Load Analysis Method cannot be used.
Dir 1: Second Order Effects are considered using code based slenderness methods.
Dir 2: Second Order Effects are considered using code based slenderness methods.
Overturning Check: Dir 1 ... Mp1 / Ma1 = 2235031.1 / 202475.9 = 11.0385 ≥ 2.0 OK
Overturning Check: Dir 2 ... Mp2 / Ma2 = 1174900.7 / 202771.8 = 5.7942 ≥ 2.0 OK
Due to Seismic Zone, Irregularities and/or Building Height Limits Equivalent Static Load Analysis Method cannot be used.
E I G E N S Y S T E M M O D A L C A S E : MODALALL
E I G E N V A L U E S A N D F R E Q U E N C I E S
M O D A L P A R T I C I P A T I N G F A C T O R S
P A R T I C I P A T I N G M A S S - ( % )
C U M U L A T I V E P A R T I C I P A T I N G M A S S - ( % )
E I G E N S Y S T E M M O D A L C A S E : MODALSUPER
Number of Eigenvalues : 6
E I G E N V A L U E S A N D F R E Q U E N C I E S
M O D A L P A R T I C I P A T I N G F A C T O R S
P A R T I C I P A T I N G M A S S - ( % )
C U M U L A T I V E P A R T I C I P A T I N G M A S S - ( % )
S Y S T E M D A T A
S E I S M I C C O D E D A T A
S P E C T R U M D A T A
SPECTRUM DATA
L O A D C A S E S D A T A
Case No. = 01
Case Type = STATIC
Case Label = D
Case Description = Sabit Yükler
Case No. = 02
Case Type = STATIC
Case Label = DC
Case Description = Sabit Yükler (Çatlamış)
Case No. = 03
Case Type = STATIC
Case Label = L
Case Description = Hareketli Yükler
Case No. = 04
Case Type = STATIC
Case Label = LC
Case Description = Hareketli Yükler (Çatlamış)
Case No. = 05
Case Type = STATIC
Case Label = LS1
Case Description = Sasirtmali H. Yükler 1
Case No. = 06
Case Type = STATIC
Case Label = LS2
Case Description = Sasirtmali H. Yükler 2
Case No. = 07
Case Type = STATIC
Case Label = EZ
Case Description = Düşey Earthquake
Case No. = 08
Case Type = EQST
Case Label = EX+
Case Description = ES Earthquake X (E+)
Eccentricity (x,y) = +0.00 , +1.00
Seismic Code = International Building Code
Spectral Func. = SPECT1
Excitation Direction = 1
Excitation Angle = 0.00
Case No. = 09
Case Type = EQST
Case Label = EX-
Case Description = ES Earthquake X (E-)
Eccentricity (x,y) = +0.00 , -1.00
Seismic Code = International Building Code
Spectral Func. = SPECT1
Excitation Direction = 1
Excitation Angle = 0.00
Case No. = 10
Case Type = EQST
Case Label = EY+
Case No. = 11
Case Type = EQST
Case Label = EY-
Case Description = ES Earthquake Y (E-)
Eccentricity (x,y) = -1.00 , +0.00
Seismic Code = International Building Code
Spectral Func. = SPECT1
Excitation Direction = 2
Excitation Angle = 90.00
C O M B I N A T I O N D A T A
Number of Combinations = 29
EX+ 0.3000
EY- 1.0000
Dc+Lc-Ey-+E SGN DC 1.0000
LC 1.0000
EZ 1.0000
EX+ -0.3000
EY- -1.0000
Dc+Ex++Ez SGN DC 0.9000
EZ -1.0000
EX+ 1.0000
EY- 0.3000
Dc-Ex++Ez SGN DC 0.9000
EZ -1.0000
EX+ -1.0000
EY- -0.3000
Dc+Ex-+Ez SGN DC 0.9000
EZ -1.0000
EX- 1.0000
EY+ 0.3000
Dc-Ex-+Ez SGN DC 0.9000
EZ -1.0000
EX- -1.0000
EY+ -0.3000
Dc+Ey++Ez SGN DC 0.9000
EZ -1.0000
EX- 0.3000
EY+ 1.0000
Dc-Ey++Ez SGN DC 0.9000
EZ -1.0000
EX- -0.3000
EY+ -1.0000
Dc+Ey-+Ez SGN DC 0.9000
EZ -1.0000
EX+ 0.3000
EY- 1.0000
Dc-Ey-+Ez SGN DC 0.9000
EZ -1.0000
EX+ -0.3000
EY- -1.0000
D+Ex++Ez SGN D 1.0000
EZ 1.0000
EX+ 1.0000
EY- 0.3000
D-Ex++Ez SGN D 1.0000
EZ 1.0000
EX+ -1.0000
EY- -0.3000
D+Ex-+Ez SGN D 1.0000
EZ 1.0000
EX- 1.0000
EY+ 0.3000
D-Ex-+Ez SGN D 1.0000
EZ 1.0000
EX- -1.0000
EY+ -0.3000
D+Ey++Ez SGN D 1.0000
EZ 1.0000
EX- 0.3000
EY+ 1.0000
D-Ey++Ez SGN D 1.0000
EZ 1.0000
EX- -0.3000
EY+ -1.0000
D+Ey-+Ez SGN D 1.0000
EZ 1.0000
EX+ 0.3000
EY- 1.0000
D-Ey-+Ez SGN D 1.0000
EZ 1.0000
EX+ -0.3000
EY- -1.0000
M A T E R I A L S D A T A
Number of Materials = 2
D I A P H R A M S M O D I F I C A T I O N D A T A
Diaph X Y Z
E Q U A T I O N N U M B E R S
================================================================================
================================================================================
Storey Displacements
Load Case Storey Diaphragm Displacement-X Displacement-Y Rotation-Z
(mm) (mm) (Rad)
1 D 1 D1-1 -0.003863 0.050995 0.000000
2 Dc 1 D1-1 -0.003863 0.050995 0.000000
3 L 1 D1-1 -0.000877 0.011024 0.000000
4 Lc 1 D1-1 -0.000877 0.011024 0.000000
5 LS1 1 D1-1 0.000074 0.002904 0.000000
6 LS2 1 D1-1 -0.000951 0.008121 0.000000
7 Ez 1 D1-1 -0.000166 0.002193 0.000000
8 Ex+ 1 D1-1 0.663530 0.005586 -0.000016
9 Ex- 1 D1-1 0.620640 0.002065 -0.000006
10 Ey+ 1 D1-1 -0.030106 0.880520 0.000007
11 Ey- 1 D1-1 0.048537 0.886970 -0.000012
1 D 1 Free Nodes -0.003716 0.050994 0.000000
(Average)
1 D 1 Free Nodes -0.004268 0.051030 0.000000
(Max)
1 D 1 Free Nodes 0.000000 0.051030 0.000000
(Min)
2 Dc 1 Free Nodes -0.003716 0.050994 0.000000
(Average)
2 Dc 1 Free Nodes -0.004268 0.051030 0.000000
(Max)
2 Dc 1 Free Nodes 0.000000 0.051030 0.000000
(Min)
3 L 1 Free Nodes -0.000891 0.011020 0.000000
(Average)
3 L 1 Free Nodes -0.001015 0.011058 0.000000
(Max)
3 L 1 Free Nodes 0.000000 0.011058 0.000000
(Min)
4 Lc 1 Free Nodes -0.000891 0.011020 0.000000
(Average)
4 Lc 1 Free Nodes -0.001015 0.011058 0.000000
(Max)
4 Lc 1 Free Nodes 0.000000 0.011058 0.000000
(Min)
5 LS1 1 Free Nodes -0.000173 0.002885 0.000000
(Average)
5 LS1 1 Free Nodes -0.000204 0.003191 0.000000
(Max)
5 LS1 1 Free Nodes 0.000000 0.003191 0.000000
(Min)
6 LS2 1 Free Nodes -0.000718 0.008135 0.000000
(Average)
6 LS2 1 Free Nodes -0.000811 0.008404 0.000000
(Max)
6 LS2 1 Free Nodes 0.000000 0.008404 0.000000
(Min)
7 Ez 1 Free Nodes -0.000160 0.002193 0.000000
(Average)
7 Ez 1 Free Nodes -0.000184 0.002194 0.000000
(Max)
7 Ez 1 Free Nodes 0.000000 0.002194 0.000000
(Min)
8 Ex+ 1 Free Nodes 0.521590 -0.007370 -0.000029
(Average)
8 Ex+ 1 Free Nodes 0.522510 -0.180700 -0.000031
(Max)
8 Ex+ 1 Free Nodes 0.000000 -0.180700 -0.000031
(Min)
9 Ex- 1 Free Nodes 0.568015 -0.002694 0.000007
(Average)
9 Ex- 1 Free Nodes 0.569310 -0.063764 0.000009
(Max)
(Average)
8 Ex+ 2 Free Nodes 1.201580 -0.367300 -0.000056
(Max)
8 Ex+ 2 Free Nodes 0.000000 -0.367300 -0.000056
(Min)
9 Ex- 2 Free Nodes 1.295140 -0.003630 0.000012
(Average)
9 Ex- 2 Free Nodes 1.295750 -0.122440 0.000015
(Max)
9 Ex- 2 Free Nodes 0.000000 -0.122440 0.000015
(Min)
10 Ey+ 2 Free Nodes 0.069405 1.930225 0.000056
(Average)
10 Ey+ 2 Free Nodes 0.069705 2.075490 0.000061
(Max)
10 Ey+ 2 Free Nodes 0.000000 2.075490 0.000061
(Min)
11 Ey- 2 Free Nodes -0.103480 1.916800 -0.000063
(Average)
11 Ey- 2 Free Nodes -0.103610 2.207190 -0.000068
(Max)
11 Ey- 2 Free Nodes 0.000000 2.207190 -0.000068
(Min)
1 D 3 D3-1 -0.025175 0.315850 0.000000
2 Dc 3 D3-1 -0.025175 0.315850 0.000000
3 L 3 D3-1 -0.005733 0.068045 0.000000
4 Lc 3 D3-1 -0.005733 0.068045 0.000000
5 LS1 3 D3-1 -0.000475 0.018691 0.000000
6 LS2 3 D3-1 -0.005258 0.049354 0.000000
7 Ez 3 D3-1 -0.001083 0.013581 0.000000
8 Ex+ 3 D3-1 2.452620 0.009082 -0.000046
9 Ex- 3 D3-1 2.327450 0.002800 -0.000015
10 Ey+ 3 D3-1 -0.095176 2.934020 0.000024
11 Ey- 3 D3-1 0.134400 2.945530 -0.000034
1 D 3 Free Nodes -0.024106 0.315955 0.000000
(Average)
1 D 3 Free Nodes -0.024546 0.317500 0.000000
(Max)
1 D 3 Free Nodes 0.000000 0.317500 0.000000
(Min)
2 Dc 3 Free Nodes -0.024106 0.315955 0.000000
(Average)
2 Dc 3 Free Nodes -0.024546 0.317500 0.000000
(Max)
2 Dc 3 Free Nodes 0.000000 0.317500 0.000000
(Min)
3 L 3 Free Nodes -0.005726 0.068050 0.000000
(Average)
3 L 3 Free Nodes -0.005823 0.068095 0.000000
(Max)
3 L 3 Free Nodes 0.000000 0.068095 0.000000
(Min)
4 Lc 3 Free Nodes -0.005726 0.068050 0.000000
(Average)
4 Lc 3 Free Nodes -0.005823 0.068095 0.000000
(Max)
4 Lc 3 Free Nodes 0.000000 0.068095 0.000000
(Min)
5 LS1 3 Free Nodes -0.001440 0.018635 0.000000
(Average)
5 LS1 3 Free Nodes -0.001484 0.019874 0.000000
(Max)
5 LS1 3 Free Nodes 0.000000 0.019874 0.000000
(Min)
6 LS2 3 Free Nodes -0.004285 0.049414 0.000000
(Average)
6 LS2 3 Free Nodes -0.004340 0.050698 0.000000
(Max)
(Average)
5 LS1 4 Free Nodes -0.002612 0.032663 0.000000
(Max)
5 LS1 4 Free Nodes 0.000000 0.032663 0.000000
(Min)
6 LS2 4 Free Nodes -0.006901 0.080803 0.000000
(Average)
6 LS2 4 Free Nodes -0.006940 0.082738 0.000000
(Max)
6 LS2 4 Free Nodes 0.000000 0.082738 0.000000
(Min)
7 Ez 4 Free Nodes -0.001719 0.022348 0.000000
(Average)
7 Ez 4 Free Nodes -0.001734 0.022484 0.000000
(Max)
7 Ez 4 Free Nodes 0.000000 0.022484 0.000000
(Min)
8 Ex+ 4 Free Nodes 3.006845 -0.027335 -0.000102
(Average)
8 Ex+ 4 Free Nodes 3.009920 -0.730180 -0.000107
(Max)
8 Ex+ 4 Free Nodes 0.000000 -0.730180 -0.000107
(Min)
9 Ex- 4 Free Nodes 3.209600 -0.008525 0.000023
(Average)
9 Ex- 4 Free Nodes 3.213080 -0.218360 0.000028
(Max)
9 Ex- 4 Free Nodes 0.000000 -0.218360 0.000028
(Min)
10 Ey+ 4 Free Nodes 0.157425 4.253680 0.000108
(Average)
10 Ey+ 4 Free Nodes 0.157590 4.577660 0.000118
(Max)
10 Ey+ 4 Free Nodes 0.000000 4.577660 0.000118
(Min)
11 Ey- 4 Free Nodes -0.214615 4.219150 -0.000120
(Average)
11 Ey- 4 Free Nodes -0.215190 4.799660 -0.000130
(Max)
11 Ey- 4 Free Nodes 0.000000 4.799660 -0.000130
(Min)
1 D 5 D5-1 -0.062593 0.760320 0.000000
2 Dc 5 D5-1 -0.062593 0.760320 0.000000
3 L 5 D5-1 -0.014209 0.163220 0.000000
4 Lc 5 D5-1 -0.014209 0.163220 0.000000
5 LS1 5 D5-1 -0.002305 0.045687 0.000000
6 LS2 5 D5-1 -0.011904 0.117530 0.000000
7 Ez 5 D5-1 -0.002692 0.032694 0.000000
8 Ex+ 5 D5-1 4.683120 0.007140 -0.000075
9 Ex- 5 D5-1 4.480710 0.001185 -0.000021
10 Ey+ 5 D5-1 -0.162090 5.237410 0.000043
11 Ey- 5 D5-1 0.209280 5.248300 -0.000056
1 D 5 Free Nodes -0.058733 0.760610 0.000000
(Average)
1 D 5 Free Nodes -0.059043 0.765840 0.000000
(Max)
1 D 5 Free Nodes 0.000000 0.765840 0.000000
(Min)
2 Dc 5 Free Nodes -0.058733 0.760610 0.000000
(Average)
2 Dc 5 Free Nodes -0.059043 0.765840 0.000000
(Max)
2 Dc 5 Free Nodes 0.000000 0.765840 0.000000
(Min)
3 L 5 Free Nodes -0.013899 0.163245 0.000000
(Average)
3 L 5 Free Nodes -0.013965 0.163680 0.000000
(Max)
(Average)
2 Dc 6 Free Nodes -0.080078 1.038610 0.000001
(Max)
2 Dc 6 Free Nodes 0.000000 1.038610 0.000001
(Min)
3 L 6 Free Nodes -0.018847 0.220840 0.000000
(Average)
3 L 6 Free Nodes -0.018907 0.221550 0.000000
(Max)
3 L 6 Free Nodes 0.000000 0.221550 0.000000
(Min)
4 Lc 6 Free Nodes -0.018847 0.220840 0.000000
(Average)
4 Lc 6 Free Nodes -0.018907 0.221550 0.000000
(Max)
4 Lc 6 Free Nodes 0.000000 0.221550 0.000000
(Min)
5 LS1 6 Free Nodes -0.005622 0.062032 0.000000
(Average)
5 LS1 6 Free Nodes -0.005652 0.064721 0.000000
(Max)
5 LS1 6 Free Nodes 0.000000 0.064721 0.000000
(Min)
6 LS2 6 Free Nodes -0.013225 0.158810 0.000000
(Average)
6 LS2 6 Free Nodes -0.013255 0.162210 0.000000
(Max)
6 LS2 6 Free Nodes 0.000000 0.162210 0.000000
(Min)
7 Ez 6 Free Nodes -0.003431 0.044332 0.000000
(Average)
7 Ez 6 Free Nodes -0.003443 0.044660 0.000000
(Max)
7 Ez 6 Free Nodes 0.000000 0.044660 0.000000
(Min)
8 Ex+ 6 Free Nodes 5.080145 -0.046630 -0.000144
(Average)
8 Ex+ 6 Free Nodes 5.084200 -1.040350 -0.000152
(Max)
8 Ex+ 6 Free Nodes 0.000000 -1.040350 -0.000152
(Min)
9 Ex- 6 Free Nodes 5.388865 -0.013985 0.000035
(Average)
9 Ex- 6 Free Nodes 5.393580 -0.279480 0.000043
(Max)
9 Ex- 6 Free Nodes 0.000000 -0.279480 0.000043
(Min)
10 Ey+ 6 Free Nodes 0.248140 6.609535 0.000158
(Average)
10 Ey+ 6 Free Nodes 0.248550 7.107570 0.000171
(Max)
10 Ey+ 6 Free Nodes 0.000000 7.107570 0.000171
(Min)
11 Ey- 6 Free Nodes -0.318600 6.549585 -0.000171
(Average)
11 Ey- 6 Free Nodes -0.319400 7.388200 -0.000185
(Max)
11 Ey- 6 Free Nodes 0.000000 7.388200 -0.000185
(Min)
1 D 7 D7-1 -0.110540 1.322320 0.000001
2 Dc 7 D7-1 -0.110540 1.322320 0.000001
3 L 7 D7-1 -0.024960 0.282730 0.000000
4 Lc 7 D7-1 -0.024960 0.282730 0.000000
5 LS1 7 D7-1 -0.005040 0.079939 0.000000
6 LS2 7 D7-1 -0.019920 0.202790 0.000000
7 Ez 7 D7-1 -0.004753 0.056860 0.000000
8 Ex+ 7 D7-1 6.957390 0.000923 -0.000096
9 Ex- 7 D7-1 6.695590 -0.002150 -0.000024
Q - Live Loads:
Storey Column Wall Beam Slab Ribbed Slab Total
8 (+29.00m) 0.0 0.0 0.0 1848.0 0.0 1848.0
7 (+25.50m) 0.0 0.0 0.0 1932.8 0.0 1932.8
6 (+22.00m) 0.0 0.0 0.0 1932.8 0.0 1932.8
5 (+18.50m) 0.0 0.0 0.0 1932.8 0.0 1932.8
4 (+15.00m) 0.0 0.0 0.0 1932.8 0.0 1932.8
3 (+11.50m) 0.0 0.0 0.0 1932.8 0.0 1932.8
2 (+8.00m) 0.0 0.0 0.0 1932.8 0.0 1932.8
1 (+4.50m) 0.0 0.0 0.0 1932.8 0.0 1932.8
Total 15377.6
Q - Live Loads:
Storey Column Wall Beam Slab Ribbed Slab Total
8 (+29.00m) 0.0 211.7 1636.2 0.0 0.0 1848.0
7 (+25.50m) 0.0 131.9 1800.9 0.0 0.0 1932.8
6 (+22.00m) 0.0 131.9 1800.9 0.0 0.0 1932.8
5 (+18.50m) 0.0 131.9 1800.9 0.0 0.0 1932.8
4 (+15.00m) 0.0 131.9 1800.9 0.0 0.0 1932.8
3 (+11.50m) 0.0 131.9 1800.9 0.0 0.0 1932.8
2 (+8.00m) 0.0 131.9 1800.9 0.0 0.0 1932.8
1 (+4.50m) 0.0 131.9 1800.9 0.0 0.0 1932.8
Total 15377.6