Professional Documents
Culture Documents
Hilti Firestop Submittal - Balamand University
Hilti Firestop Submittal - Balamand University
Table of Contents
4. Technical Data
www.hiltiPHFRP
Hilti Lebanon offers the following value-adding services for our dear customers:
• Mock-Ups for firestop system installations, to show the customers how the
systems are applied and look like.
• Full Technical Support, to back up the numerous UL- & BS-tested & approved
systems.
• UL- & BS-based Engineering Judgments (EJ) by certified Hilti Fire Protection
Engineers, to represent firestop systems that would be expected to pass the
stated ratings and requirements if tested, for those situations where the tested
system is not doable at site.
CAJ1372c.110402
T-RATING = 0-HR.
L-RATING AT AMBIENT = LESS THAN 1 CFM/SQ. FT.
L-RATING AT 400° F = 4 CFM/ SQ. FT.
TOP VIEW SECTION A-A
3
5
1 2 6
A A
FS-ONE
High performance Intumescent
firestop sealant
Product description
Intumescent (expands when exposed to fire) firestop
sealant that helps protect combustible and non-
combustible penetrations for up to 4 hours fire rating.
Areas of application
Steel (<30”), copper (<6”), cast iron (<30”) and EMT pipes.
Insulated steel and copper pipes.
Cable bundles.
Closed or vented plastic pipes.
HVAC penetrations.
Base Materials
Concrete, masonry, drywall and wood floor assemblies.
Wall and floor assemblies rated up to 4 hours.
Product Features
System advantages / customer benefits
Expanding in fire protection pipes and cable penetrations.
Smoke, gas and water tight. Protects more than 95% of all typical firestop application.
Halogen and solvent free. Easy to work with and fast cleanup.
Odourless, water based, easy to clean. Can be repenetrated when laying new cables.
High fire rating properties. Can be painted.
Sealing around compushible and non-compushible Meets LEEDTM requirements for indoor
penetration in fire-rated construction. environmental quality credit
FS-ONE
High Performance Intumescent firestop sealant
Ordering Color Packaging Volume Item no.
designation contents
"%
Installation Instructions
1. Clean opening 2. Pack mineral 3. Apply FS-ONE 4. Smooth 5. Leave completed 6. Fasten
wool. (if required) FS-ONE seal undisturbed for identification plate
48 hours (if required)
Pipe installation
1. Clean opening 2. Pack mineral 3. Apply FS-ONE 4. Smooth 5. Leave completed 6. Fasten
wool. (if required) FS-ONE seal undisturbed for identification plate
48 hours (if required)
"'
Product Information
CP 606
Fire resistant joint filler
Product description
An acrylic based firestop mastic that offers movement
capabilities and excellent acoustic rating in fire rated joint
applications. Provides up to 4hrs integrity in various
applications when tested to BS476 Part 20.
Areas of application
Sealing header joints
Sealing drywall partition connections
Sealing joints to CP670 firestop safety board
Metal pipes
Rigid and low movement joints
Tested on metal pipes in walls, floors and drywall.
Product features
Silicone free System advantages/customer benefits
Halogen and solvent free Paintable
UV resistant Simple use and application
Smoke, gas and water tight
Base materials
Easy clean up with water
Concrete, Masonry, Drywall
Approved for infinite linear gap lengths
Steel, Porous concrete
Meets LEEDTM requirements for indoor
(Wall and floor thickness from 100mm)
environmental quality credit
(Joint widths from 6-100mm)
British Standard
BS 476
Other tests include : UL 2079 : ASTM E 1399 : UL 1479 : ASTM E 814 : ASTM E 84
Recommendations
Can be used in conjunction with a suitable backing material:
– Non flammable mineral wool (min. 100kg/m 3 per BS).
– Hilti CF125-50 fire rated backing foam for construction joints only*
*Please note fire rating will be reduced.
Storage
Store only in the original packaging in a location protected
from moisture at a temperature of 5˚C to 25˚C.
Observe expiry date on top of cartridge.
CP 606
Fire resistant joint filler
Description Ordering Item no.
designation 310 ml catridge 580 ml foil
Fire resistant joint filler, white CP 606 (310ml) 209625
Fire resistant joint filler, gray CP 606 (310ml) 209630
Fire resistant joint filler, gray CP 606 (580ml) 214050
Fire resistant joint filler, white CP 606 (580ml) 209632
Manual dispenser CS 201-P1 225555 310 ml 600 ml
Manual dispenser CS 270 P1 24669
1(
Installation Instructions
CP 606
Fire resistant joint filler
Technical Data
CP 606
Density 1.58 g/cm³
Application Temperature 5°C - 40°C
Range
Skin forming time (at 15 min
23°C/50% r.H)
Cure Time (at 23°C/50% r.H) approx. 3 mm/ 3 days
Volume shrinkage <20 %
Movement ±10 %
Temperature resistance tem - -30°C - 100°C
perature range
Shelf life (@73°F/23°C and 50% 24 months
relative humidity)
Chemical basis Acrylic
Application Dimensions
Joint sides must be sound, dry and free from dust, oil or grease. The following dimensions must be observed when using CP 606
Check whether a primer is required for adhesion to the substrate. fire resistant joint filler.
In walls apply CP 606 to both sides of the joint.
Insert backfill of non-flammable mineral wool (at least a b
100 kg/m3 + melting point > 1000OC), Hilti CF 125-50 foam or b a
PE backing rod.
Smooth firestop sealant with water before the skin forms.
Remove CP 606 firestop sealant before it cures using water
Once cured, it can only be removed mechanically. Floor Wall
1)
Firestop Collars, Wraps and Bandages
■ Maximum flexibility
www.hilti.com
424
Material Safety
Data Sheet
Page 1/3
Material Safety Data Sheet
According to 91/155 EEC
Printing date 15.03.2004 Reviewed on 15.03.2004
* 1 Identification of substance:
· Product details:
· Trade name: FS-ONE - CP 612
· Application of the substance / the preparation Acrylic sealant
· Manufacturer/Supplier:
Hilti AG
FL-9494 Schaan
· Informing department: see section 16
· Emergency information:
Tel.: 00423 / 234 - 2111
Fax.: 00423 / 234 - 2965
Schweizerisches Toxikologisches Informationszentrum - 24 h Service
Tel.: 0041 / 1 251 51 51 (international)
* 2 Composition/Data on components:
· Chemical characterization
· Description: Watery, acrylate dispersion with filler
· Dangerous components:
CAS: 107-21-1 ethane-1,2-diol Xn; R 22 <2,5%
EINECS: 203-473-3
CAS: 65997-17-3 Fiberglas Xi; R 36/37/38 <2,5%
· Additional information For the wording of the listed risk phrases refer to section 16.
* 3 Hazards identification
· Suitable extinguishing agents CO2, extinguishing powder or water jet. Fight larger fires with water jet or alcohol-resistant foam.
· Special hazards caused by the material, its products of combustion or resulting gases:
Can be released in case of fire
Carbon monoxide (CO)
Carbon dioxide (CO2)
· Protective equipment: Do not inhale explosion gases or combustion gases.
· Handling
· Information for safe handling: No special measures required.
· Information about protection against explosions and fires: No special measures required.
· Storage
· Requirements to be met by storerooms and containers: Keep containers securely closed and dry, store at 5 - 25°C.
· Information about storage in one common storage facility: Not required.
(Contd. on page 2)
FLE
DR
Page 2/3
Material Safety Data Sheet
According to 91/155 EEC
Printing date 15.03.2004 Reviewed on 15.03.2004
(Contd. of page 1)
· Further information about storage conditions: None.
· Additional information about design of technical systems: No further data; see item 7.
· Components with limit values that require monitoring at the workplace:
107-21-1 ethane-1,2-diol (d 2,5%)
MAK 26 mg/m3, 10 ml/m3
· Additional information: The lists that were valid during the compilation were used as basis.
· Personal protective equipment
· General protective and hygienic measures The usual precautionary measures should be adhered to general rules for handling chemicals.
· Breathing equipment: Not necessary if room is well-ventilated.
· Protection of hands: Protective gloves.
· Material of gloves Synthetic gloves
· Penetration time of glove material
The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.
· Eye protection: Safety glasses
· Body protection: Protective work clothing.
· General Information
Form: Pasty
Colour: Red
Odour: Characteristic
· Change in condition
Melting point/Melting range: Not determined
Boiling point/Boiling range: Not determined
· Flash point: Not applicable
· Self-inflammability: Product is not selfigniting.
· Danger of explosion: Product is not explosive.
· Density at 20°C 1,5 g/cm³ (DIN 51757)
· Solubility in / Miscibility with
Water: Slightly soluble
* 11 Toxicological information
· Acute toxicity:
· LD/LC50 values that are relevant for classification:
107-21-1 ethane-1,2-diol
Oral LD50 5840 mg/kg (ratte)
Dermal LD50 9530 mg/kg (rbt)
· Primary irritant effect:
· on the skin: No irritant effect.
· on the eye: No irritant effect.
· Sensitization: No sensitizing effect known.
· Additional toxicological information:
When used and handled according to specifications, the product does not have any harmful effects according to our experience and the information
provided to us.
* 12 Ecological information:
· General notes:
Water hazard class 1 (German Regulation) (Self-assessment): slightly hazardous for water.
Do not allow undiluted product or large quantities of it to reach ground water, water bodies or sewage system.
FLE
(Contd. on page 3)
DR
Page 3/3
Material Safety Data Sheet
According to 91/155 EEC
Printing date 15.03.2004 Reviewed on 15.03.2004
* 13 Disposal considerations
· Product:
· Recommendation For disposal, local regulations issued by the authorities must be observed.
· European waste catalogue
08 00 00 WASTES FROM THE MANUFACTURE, FORMULATION, SUPPLY AND USE (MFSU) OF COATINGS (PAINTS, VARNISHES
AND VITREOUS ENAMELS), ADHESIVES, SEALANTS AND PRINTING INKS
08 04 00 wastes from MFSU of adhesives and sealants (including waterproofing products)
08 04 10 waste adhesives and sealants other than those mentioned in 08 04 09
· Uncleaned packagings:
· Recommendation: Disposal must be made according to official regulations.
* 14 Transport information
* 15 Regulatory information
· Water hazard class: Water hazard class 1 (Self-assessment): slightly hazardous for water.
* 16 Other information:
These data are based on our present knowledge. However, they shall not constitute a guarantee for any specific product features and shall not
establish a legally valid contractual relationship.
Changes made since last issue dated 15.02.2002 at the following points: *
· Relevent R-phrases
22 Harmful if swallowed.
36/37/38 Irritating to eyes, respiratory system and skin.
· Department issuing data specification sheet:
Hilti Corp.
BU Chemicals
Quality/Safety/Environment
DR
Page 1/3
Material Safety Data Sheet
According to 91/155 EEC
Printing date 15.03.2004 Reviewed on 15.03.2004
1 Identification of substance:
· Product details:
· Trade name: CP 606
· Application of the substance / the preparation Acrylic sealant
· Manufacturer/Supplier:
Hilti AG
FL-9494 Schaan
· Informing department: see section 16
· Emergency information:
Tel.: 00423 / 234 - 2111
Fax.: 00423 / 234 - 2965
Schweizerisches Toxikologisches Informationszentrum - 24 h Service
Tel.: 0041 / 1 251 51 51 (international)
2 Composition/Data on components:
· Chemical characterization
· Description: Watery, acrylate dispersion with filler
· Dangerous components:
CAS: 107-21-1 ethane-1,2-diol Xn; R 22 2-5%
EINECS: 203-473-3
· Additional information For the wording of the listed risk phrases refer to section 16.
3 Hazards identification
· Suitable extinguishing agents CO2, extinguishing powder or water jet. Fight larger fires with water jet or alcohol-resistant foam.
· For safety reasons unsuitable extinguishing agents Water with a full water jet.
· Special hazards caused by the material, its products of combustion or resulting gases:
Can be released in case of fire
Carbon monoxide (CO)
Carbon dioxide (CO2)
· Protective equipment: Do not inhale explosion gases or combustion gases.
· Handling
· Information for safe handling: No special measures required.
· Information about protection against explosions and fires: No special measures required.
· Storage
· Requirements to be met by storerooms and containers: Keep containers securely closed and dry, store at 5 - 25°C.
· Information about storage in one common storage facility: Not required.
(Contd. on page 2)
FLE
DR
Page 2/3
Material Safety Data Sheet
According to 91/155 EEC
Printing date 15.03.2004 Reviewed on 15.03.2004
(Contd. of page 1)
· Further information about storage conditions: None.
· Additional information about design of technical systems: No further data; see item 7.
· Components with limit values that require monitoring at the workplace:
107-21-1 ethane-1,2-diol (2-5%)
TLV (European Union) Short-term value: 104 mg/m³, 40 ml/m³
Long-term value: 52 mg/m³, 20 ml/m³
Skin
· Additional information: The lists that were valid during the compilation were used as basis.
· Personal protective equipment
· General protective and hygienic measures The usual precautionary measures should be adhered to general rules for handling chemicals.
· Breathing equipment: Not necessary if room is well-ventilated.
· Protection of hands: Protective gloves.
· Material of gloves Synthetic gloves
· Penetration time of glove material
The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.
· Eye protection: Safety glasses
· Body protection: Protective work clothing.
· General Information
Form: Pasty
Colour: Various colours
Odour: Characteristic
· Change in condition
Melting point/Melting range: Not determined
Boiling point/Boiling range: Not determined
· Flash point: Not applicable
· Ignition temperature: Not applicable
· Danger of explosion: Product is not explosive.
· Vapour pressure at 20°C: ca. 23 hPa
· Density at 20°C ca. 1,55 g/cm3 (DIN 51757)
· Solubility in / Miscibility with
Water: Fully miscible
* 11 Toxicological information
· Acute toxicity:
· LD/LC50 values that are relevant for classification:
107-21-1 ethane-1,2-diol
Oral LD50 5840 mg/kg (ratte)
Dermal LD50 9530 mg/kg (rbt)
· Primary irritant effect:
· on the skin: No irritant effect.
· on the eye: No irritant effect.
· Sensitization: No sensitizing effect known.
· Additional toxicological information:
When used and handled according to specifications, the product does not have any harmful effects according to our experience and the information
provided to us.
12 Ecological information:
DR
Page 3/3
Material Safety Data Sheet
According to 91/155 EEC
Printing date 15.03.2004 Reviewed on 15.03.2004
(Contd. of page 2)
Do not allow undiluted product or large quantities of it to reach ground water, water bodies or sewage system.
13 Disposal considerations
· Product:
· Recommendation For disposal, local regulations issued by the authorities must be observed.
· European waste catalogue
08 00 00 WASTES FROM THE MANUFACTURE, FORMULATION, SUPPLY AND USE (MFSU) OF COATINGS (PAINTS, VARNISHES
AND VITREOUS ENAMELS), ADHESIVES, SEALANTS AND PRINTING INKS
08 04 00 wastes from MFSU of adhesives and sealants (including waterproofing products)
08 04 10 waste adhesives and sealants other than those mentioned in 08 04 09
· Uncleaned packagings:
· Recommendation: Disposal must be made according to official regulations.
14 Transport information
15 Regulatory information
· Water hazard class: Water hazard class 1 (Self-assessment): slightly hazardous for water.
* 16 Other information:
These data are based on our present knowledge. However, they shall not constitute a guarantee for any specific product features and shall not
establish a legally valid contractual relationship.
Changes made since last issue dated 20.10.2003 at the following points: *
· Relevent R-phrases
22 Harmful if swallowed.
· Department issuing data specification sheet:
Hilti Corp.
BU Chemicals
Quality/Safety/Environment
DR