Professional Documents
Culture Documents
(07/03/16)
High level of function and safety
ø30mm XN Series Emergency Stop Switches
IDEC’s new ø30mm XN series emergency stop switches with Safe Break Action and Safety
Potential Structure ensure the highest level of safety and functionality.
Closed ON
High
High
Open (OFF)
Energy
Energy
When the contact block is detached from the operator, a rotating
cam directly opens the NC main contacts (contacts are off).
Low
Low
Direct Opening Action
Normal Status Latched Normal Status Latched
Achievement of contact separation (of a contact element) of the
switch actuator through non-resilient members (for example not NC contacts:
ON (machine
NC contacts: OFF
(machine cannot
dependent upon springs) can operate) operate)
Safety Lock Mechanism With the XN emergency stop switches, the potential energy level of
The emergency stop signal shall be maintained until the the latched status is lower than that of the normal status. In the
emergency stop device is reset (disengaged). (IEC 60947-5-5; 6.2) event the contact block is damaged due to excessive shocks, the
NC contacts will turn off, thus leading to safety by stopping the
machine.
Flush bezel type extends out only Plastic bezel type with four contacts is
21 mm from the front of the panel. only 47.7 mm deep behind the panel.
Same dimensions
Conventional 2-contact for any number of contacts
emergency stop switch and for illuminated type.
47.
mm
7
Space Saving
2 (07/03/16)
New Resetting Concept — Padlockable Emergency Stop Switches
Safety Concept
OSHA (Occupational Safety & Health Administration, U.S.
Department of Labor) requires that where the unexpected
energization or start-up of the machine or equipment or release of
stored energy could cause injury to operators, the machine or
equipment is stopped, isolated from all potentially hazardous
energy sources and locked out before employees perform any
servicing or maintenance.
ISO 12100-2: 2003 also requires that risks be reduced to the
lowest allowable level by taking protective measures in order of
inherently safe design, safeguarding, and complementary
protective measures. Locking out the energy isolation devices is
one of complementary protective measures.
Inspired by the lockout concept, IDEC’s XN series emergency stop
switches have been developed to prevent unauthorized reset of
the latched emergency stop switches.
Note:
OSHA 29CFR 1910.147 – The control of hazardous energy (lockout/tagout)
ANSI Z244.1-2003 Control of Hazardous Energy - Lockout/Tagout and Alternative
Methods
to reset.
Button Safety
Using hasps makes it possible to install a Latched Confirmed
maximum of 20 padlocks
(1,500g maximum in total).
When preventing
Padlocks and hasps are not supplied by
unauthorized resetting
IDEC with the XN series emergency stop
switches and must be ordered separately. Install the padlock. Remove
the padlock.
Hasp can
be used.
Notes:
• The XN series emergency stop switch is an additional protective measure.
• Padlockable safety switches for door guards are also available from IDEC.
• Perform a risk assessment before using the XN series emergency stop switches.
• Operators must observe the rules in the work place in order to ensure safety by using emergency stop switches.
Residual risk such as failure to install padlocks on the emergency stop switches must be taken into consideration.
(07/03/16) 3
ø30 XN Series Emergency Stop Switches
ø30 mm, 4-contact Emergency Stop Switch.
Padlockable and flush bezel types are available.
• Padlockable type, flush bezel type, ø60mm jumbo mushroom,
illuminated type, LED push-on type are available.
• IDEC’s original “Safe break action” and safety potential structure
ensures the highest level of safety.
• Safety lock mechanism (IEC 60947-5-5, 6.2)
• Direct opening action mechanism (IEC 60947-5-5, 5.2, IEC60947-
5-1, Annex K)
• Short depth behind the panel - only 47.7 mm for 4-contact, illumi-
nated type (flush bezel: 60.4 mm, padlockable: 61.4 mm)
• Padlockable type can be locked using padlocks when latched
(main contact: OFF). The rugged aluminum diecast shroud allows
for installing a maximum of 20 padlocks using a hasp (total weight:
1500g maximum).
• RoHS compliant (EU directive 2002/95/EC). Contains no lead,
cadmium, mercury, hexavalent chromium, PBB, or PBDE.
• Gold-plated silver contacts. Direct Opening Action
• Red (Munsell 5R4/12) or bright red (Munsell 7.5R4.5/14) colors
are available.
4 (07/03/16)
XN Series Emergency Stop Switches ø30
Plastic Bezel Type
• Non-illuminated Emergency Stop Switch
NC Main NO Monitor Type No. Operator
Appearance
Contact Contact IP20 Fingersafe Terminal w/Terminal Cover Color Code
ø40mm Mushroom 1NC — XN1E-BV401MF➀ XN1E-BV401M➀
2NC — XN1E-BV402MF➀ XN1E-BV402M➀
3NC — XN1E-BV403MF➀ XN1E-BV403M➀
4NC — XN1E-BV404MF➀ XN1E-BV404M➀
1NC 1NO XN1E-BV411MF➀ XN1E-BV411M➀
2NC 1NO XN1E-BV412MF➀ XN1E-BV412M➀
3NC 1NO XN1E-BV413MF➀ XN1E-BV413M➀
2NC 2NO XN1E-BV422MF➀ XN1E-BV422M➀ R: Red
ø60mm Jumbo Mushroom 1NC — XN1E-BV501MF➀ XN1E-BV501M➀ RH: Bright red
2NC — XN1E-BV502MF➀ XN1E-BV502M➀
3NC — XN1E-BV503MF➀ XN1E-BV503M➀
4NC — XN1E-BV504MF➀ XN1E-BV504M➀
1NC 1NO XN1E-BV511MF➀ XN1E-BV511M➀
2NC 1NO XN1E-BV512MF➀ XN1E-BV512M➀
3NC 1NO XN1E-BV513MF➀ XN1E-BV513M➀
2NC 2NO XN1E-BV522MF➀ XN1E-BV522M➀
• Specify a color code in place of ➀ in the Type No.
• Only solid wires can be used on the IP20 fingersafe terminal type.
24V
LED 3NC — XN1E-TV403Q4MFR XN1E-TV403Q4MR Red only
AC/DC
• Push-ON type is illuminated when the operator is latched, and turns off when reset.
• Only solid wires can be used on the IP20 fingersafe terminal type.
(07/03/16) 5
ø30 XN Series Emergency Stop Switches
Flush Bezel Type
• Non-illuminated Emergency Stop Switch
NC Main NO Monitor Type No. Operator
Appearance
Contact Contact IP20 Fingersafe Terminal w/Terminal Cover Color Code
ø40mm Mushroom 1NC — XN5E-BV401MF➀ XN5E-BV401M➀
2NC — XN5E-BV402MF➀ XN5E-BV402M➀
3NC — XN5E-BV403MF➀ XN5E-BV403M➀
4NC — XN5E-BV404MF➀ XN5E-BV404M➀ R: Red
1NC 1NO XN5E-BV411MF➀ XN5E-BV411M➀ RH: Bright red
2NC 1NO XN5E-BV412MF➀ XN5E-BV412M➀
3NC 1NO XN5E-BV413MF➀ XN5E-BV413M➀
2NC 2NO XN5E-BV422MF➀ XN5E-BV422M➀
• Specify a color code in place of ➀ in the Type No.
• Only solid wires can be used on the IP20 fingersafe terminal type.
24V
LED 3NC — XN5E-TV403Q4MFR XN5E-TV403Q4MR Red only
AC/DC
• Push-ON type is illuminated when the operator is latched, and turns off when reset.
• Only solid wires can be used on the IP20 fingersafe terminal type.
6 (07/03/16)
XN Series Emergency Stop Switches ø30
Padlockable Type
• Non-illuminated Emergency Stop Switch
NC Main NO Monitor Type No. Operator
Appearance
Contact Contact IP20 Fingersafe Terminal w/Terminal Cover Color
ø44mm Mushroom 1NC — XN4E-BL401MFRH XN4E-BL401MRH
2NC — XN4E-BL402MFRH XN4E-BL402MRH
3NC — XN4E-BL403MFRH XN4E-BL403MRH
4NC — XN4E-BL404MFRH XN4E-BL404MRH Bright red
1NC 1NO XN4E-BL411MFRH XN4E-BL411MRH only
2NC 1NO XN4E-BL412MFRH XN4E-BL412MRH
3NC 1NO XN4E-BL413MFRH XN4E-BL413MRH
2NC 2NO XN4E-BL422MFRH XN4E-BL422MRH
• Only solid wires can be used on the IP20 fingersafe terminal type.
• Padlocks and hasps are not supplied with the emergency stop switches and must be ordered separately. See page 10.
24V
LED 3NC — XN4E-TL403Q4MFR — Red only
AC/DC
• Push-ON type is illuminated when the operator is latched, and turns off when reset.
• Only solid wires can be used on the IP20 fingersafe terminal type.
• Padlocks and hasps are not supplied with the emergency stop switches and must be ordered separately. See page 10.
(07/03/16) 7
ø30 XN Series Emergency Stop Switches
Dimensions
Plastic Bezel Type
R0 +0.2
• Non-illuminated 4.8 R0 +0.2
.8m 0 .8 4.8 0
ax ma
. x.
ø3 ø3
0.5 0.5
IP20 Fingersafe +0
w/Terminal Cover +0
18.5
18.5
.5 .5
0 0
+0.5
+0.5
0
0
33.0
33.0
20.1
20.1
47.7 33 47.7 33
Panel Cut-out Panel Cut-out
Locking Ring Locking Ring
Rubber Gasket Rubber Gasket
M3 Terminal M3 Terminal
Screws ø4 Screws ø4
0 0
37
37
IP20 Cover Panel Thickness 1 to 5 ø40 mm Terminal Cover Panel Thickness ø40 mm
Mushroom 1 to 5 Mushroom
XW9Z-VL2MF XW9Z-VL2M
ø6
ø6
0
0
33 ø60 mm 33
ø60 mm
Jumbo Mushroom Jumbo Mushroom
• Illuminated/Push-ON R0
4.8
+0.2 R0
.8 4.8
+0.2
.8 0 0
ma ma
x. x.
IP20 Fingersafe ø3
0.5 +0
w/Terminal Cover ø3
0.5 +0
18.5
.5 .5
0 0
18.5
+0.5
+0.5
33.0 0
33.0 0
20.1
20.1
47.7 33 47.7 33
Panel Cut-out Panel Cut-out
Locking Ring
Locking Ring Rubber Gasket
Rubber Gasket Illuminated Push-ON M3 Terminal
Illuminated Push-ON M3 Terminal Screws
ø4 ø4
Screws 0 0
37
37
.5 +0
18.5
ø41
0 .5
0
+0.5
ø41
+0.5
0
33.0 0
33.0
20.1
20.1
60.4 21
60.4 21 Panel Cut-out
M3 Terminal Locking Ring Panel Cut-out
Screws Locking Ring Rubber Gasket Rubber Gasket
M3 Terminal Screws ø4
ø4 0
0
37
37
• Illuminated/Push-ON
IP20 Fingersafe R0
.8 4.8
+0.2
0
w/Terminal Cover R0
.8 4.8
+0.2
0
ma ma
x. x.
ø3 ø3
0.5 0.5
18.5
+0
18.5
.5 +0
ø41
.5
ø41
0 0
+0.5
+0.5
0
33.0 0
33.0
20.1
20.1
60.4 21 60.4 21
Panel Cut-out Panel Cut-out
Locking Ring Rubber Gasket Locking Ring
Illuminated Push-ON Rubber Gasket
M3 Terminal Screws ø4 Illuminated Push-ON M3 Terminal Screws ø4
0 0
37
37
8 (07/03/16)
XN Series Emergency Stop Switches ø30
Dimensions
Padlockable Type
R0 R0
• Non-illuminated
+0.2 +0.2
.8 4.8 0 .8 4.8 0
ma ma
x. x.
ø3 ø3
0 .5 +0 0.5 +0
18.5
IP20 Fingersafe .5
w/Terminal Cover .5
18.5
0 0
+0.5
+0.5
0
0
33.0
33.0
20.1
20.1
59.9 Panel Cut-out
Panel Cut-out
61.4 43 61.4 43
Locking Ring Rubber Gasket Locking Ring Rubber Gasket
ø4
ø4
M3 Terminal Screws M3 Terminal Screws
4
4
37
18.5
.5 .5
18.5
0 0
IP20 Fingersafe w/Terminal Cover
+0.5
+0.5
0
0
33.0
33.0
20.1
20.1
59.9 59.9
Panel Cut-out Panel Cut-out
61.4 43 61.4 43
Locking Ring Rubber Gasket
Locking Ring Rubber Gasket
Illuminated Push-ON Illuminated Push-ON
ø4
ø4
M3 Terminal Screws
M3 Terminal Screws
4
4
37
37
∗1
∗2
∗1
∗2
∗1
∗2
∗1
∗2
∗1
∗2
∗1
∗2
∗1
∗2
∗1
∗2
∗1
∗2
∗1
∗2
∗1
∗2
∗2 ∗1 ∗4 ∗3 ∗4 ∗3 X1 ∗2 ∗1 X2 X1 ∗4 ∗3 X2 X1 ∗4 ∗3 X2
1NC: Terminals on right 1NC: Terminals on top 1NC: Terminals on right 1NC: Terminals on top
2NC: Terminals on right 2NC: Terminals on right 2NC: Terminals on right 2NC: Terminals on right
and left and left and left and left
3NC: Terminals on right, 3NC: Terminals on right,
left, and top left, and top
6.0 max.
3.2 min.
∗1
∗2
∗1
∗2
∗1
∗2
41
X1 X2 X1 X2
Left Right
21
42
(07/03/16) 9
ø30 XN Series Emergency Stop Switches
Accessories and Replacement Parts
Package
Name & Appearance Material Type No. Ordering Type No. Remarks
Quantity
Terminal Cover
IP20 Fingersafe
Terminal Cover • Black
• Used to change terminal cover type to IP20
Polyamide XW9Z-VL2MF XW9Z-VL2MFPN02 2 fingersafe terminal type.
• Only solid wires can be used. Once installed,
IP20 terminal cover cannot be removed.
90
49.5
20.5
Metal TWST-T1 TWST-T1 1
52
23.7 77
Note:
• The XN series emergency stop switches are supplied with either terminal cover or IP20 fingersafe terminal cover.
• Padlocks and hasps are not supplied and must be ordered separately.
Nameplates
Package Legend Mounting Panel
Description & Appearance Type No. Legend Material Plate Color
Quantity Color Thickness
Emergency Stop Switch Nameplate
HNAV-0 (blank) XN4E- L4:
Yellow
ø60
1.0 to 4.5 mm
(Munsell
ø44 1 Polyamide Black
2.5Y 8/10
XN E- V4:
or equivalent
ø3 HNAV-27 EMERGENCY STOP 1.0 to 3.5 mm
0
1.5 1.0
Padlock and Hasp Use only padlocks or hasps that satisfy the specifications shown on
the left. The maximum total weight for padlocks and hasps is 1500g.
Padlocks and hasps of the following specifications can be used with
Make sure that the total weight does not exceed 1500g, otherwise
padlockable emergency stop switches.
the XN emergency stop switch may be damaged.
Padlock Size Make sure that locking and unlocking of the padlock and hasp do
A B C D not interfere with other devices.
7 mm maximum 19 mm minimum 39 mm minimum
15 mm minimum Padlocks and hasps are available from the following manufacturers.
(Note)
Note: When the padlock is installed from the side of the bezel as shown on Manufacturer URL
page 3, dimension D requires a minimum of 6 mm. When the padlock is PANDUIT CORP. http://www.panduit.com/
installed from the front of the button, dimension D requires a minimum
of 15 mm. Master Lock® Company LLC http://www.masterlock.com/
Recommended Hasps
C
Manufacturer Type No.
B A
PSL-HD3
PANDUIT CORP.
PSL-1A
420
Master Lock
D
421
10 (07/03/16)
XN Series Emergency Stop Switches ø30
Operating Instructions
(07/03/16) 11
ø30 XN Series Emergency Stop Switches
Safety Precautions
• Turn off power to the XN series emergency stop switch • Use wires of the proper size to meet the voltage and cur-
before installation, removal, wiring, maintenance, and rent requirements, and tighten the M3 terminal screws to
inspection of the switches. Failure to turn power off may the recommended tightening torque of 0.6 to 1.0 N·m.
cause electrical shock or fire hazard. If improper wire is used or the screw is tightened loosely,
the switch may heat during operation, causing fire hazard.
Also, provide proper protection for electric shocks.
ø22mm XW Series
The world’s shortest ø22mm, 4-contact emergency stop switch—
only 48.7 mm deep behind the panel.
• Contact: Main 1NC to 4NC, Monitor 1NO to 2NO
• Rated Operating Current: Main contacts
AC: 250V, 3A (resistive load)
DC: 250V, 0.2A (resistive load)
Monitor contacts
AC: 250V, 0.6A (resistive load)
DC: 250V, 0.2A (resistive load)
• Illumination Ratings: 24V AC/DC, 15 mA
Specifications and other descriptions in this catalog are subject to change without notice.
7-31, Nishi-Miyahara 1-Chome, Yodogawa-ku, Osaka 532-8550, Japan
Tel: +81-6-6398-2571, Fax: +81-6-6392-9731
E-mail: products@idec.co.jp
IDEC CORPORATION (USA) IDEC ELEKTROTECHNIK GmbH IDEC IZUMI (H.K.) CO., LTD.
1175 Elko Drive, Sunnyvale, CA 94089-2209, USA Wendenstrasse 331, 20537 Hamburg, Germany Unit 1505-07, DCH Commercial Centre No. 25,
Tel: +1-408-747-0550 / (800) 262-IDEC (4332) Tel: +49-40-25 30 54 - 0, Fax: +49-40-25 30 54 - 24 Westlands Road, Quarry Bay, Hong Kong
Fax: +1-408-744-9055 / (800) 635-6246 E-mail: service@idec.de Tel: +852-2803-8989, Fax: +852-2565-0171
E-mail: opencontact@idec.com E-mail: info@hk.idec.com
IDEC (SHANGHAI) CORPORATION
IDEC CANADA LIMITED Room 608-609, 6F, Gangtai Plaza, No. 700, IDEC TAIWAN CORPORATION
Unit 22-151, Brunel Road, Mississauga, Ontario, Yan'an East Road, Shanghai 200001, PRC 8F-1, No. 79, Hsin Tai Wu Road, Sec. 1,
L4Z 1X3, Canada Tel: +86-21-5353-1000, Fax: +86-21-5353-1263 Hsi-Chih, Taipei County, Taiwan
Tel: +1-905-890-8561, Toll Free: (888) 317-4332 E-mail: idec@cn.idec.com Tel: +886-2-2698-3929, Fax: +886-2-2698-3931
Fax: +1-905-890-8562 E-mail: service@tw.idec.com
E-mail: sales@ca.idec.com
IDEC (BEIJING) CORPORATION
Room 211B, Tower B, The Grand Pacific Building, IDEC IZUMI ASIA PTE. LTD.
IDEC AUSTRALIA PTY. LTD. 8A Guanghua Road, Chaoyang District, No. 31, Tannery Lane #05-01, Dragon Land
2/3 Macro Court, Rowville, Victoria 3178, Australia Beijing 100026, PRC Building, Singapore 347788
Tel: +61-3-9763-3244, Toll Free: 1800-68-4332 Tel: +86-10-6581-6131, Fax: +86-10-6581-5119 Tel: +65-6746-1155, Fax: +65-6844-5995
Fax: +61-3-9763-3255 E-mail: info@sg.idec.com
E-mail: sales@au.idec.com
IDEC (SHENZHEN) CORPORATION
Unit AB-3B2, Tian Xiang Building, Tian’an Cyber Park,
IDEC ELECTRONICS LIMITED Fu Tian District, Shenzhen, Guang Dong 518040, PRC
Unit 2, Beechwood, Chineham Business Park, Tel: +86-755-8356-2977, Fax: +86-755-8356-2944
Basingstoke, Hampshire RG24 8WA, UK
Tel: +44-1256-321000, Fax: +44-1256-327755
www.idec.com E-mail: sales@uk.idec.com
(07/03/16)