Professional Documents
Culture Documents
Product description
Discharge pressure
Technical data
Maximum discharge pressure is 12 bar
Differential pressure
Maximum differential pressure is 7 bar but is reduced at low viscosities as shown in the
table below.
Viscosity, mm2/s (cSt) 2 3 4 5 6 7 8 9 10
Max. diff. pressure (bar) 4.2 4.7 5.1 5.5 5.8 6.0 6.3 6.5 6.7
2 www.imo.se
Material and design
IVBP NTBP
Pump body Pearlitic cast iron Nodular cast iron
Power rotor Steel, surface treated Steel, surface treated
Idler rotors Pearlitic cast iron, Pearlitic cast iron,
surface treated surface treated
Shaft seal Carbon/Ni-resist Carbide/Carbide
Viton elastomers Viton elastomers
Viscosity table
cSt 2 4 8 20 37 75 200 400 800 1500
SSU 32.6 39.2 52.2 99.4 174 346 927 1850 3700 6940
Units
The following units are frequently used for specification of pumps:
SI-unit IMO units USA units conversion
Pressure Pa (MPa) bar psi 1 bar = 14,5 psi = 0,1 MPa
Speed r/s rpm rpm 1 rpm = 0,016667 r/s
Viscosity mm2/s cSt SSU see table
Temperature °C °C °F °C = (°F-32)/1.8
Length m mm inch 1 mm = 0,0394 inch
Flow rate m3/s lit/min GPM 1 lit/min = 0,264 GPM
Pump series
ACD
Size
(Power rotor diameter, mm)
Lead
L=Low lead
N=Normal lead
Generation
Design generation 6
Mounting
B=Flange mounting
Valve
P=Pressure relief valve included
Special design
ACD6 1116.02 GB
www.imo.se 3
Selection guide 50 Hz
Size Visc. (lit/min) Speed: 1450 rpm Speed: 2900 rpm
& Diff. pressure (bar) Min.inlet Diff. pressure (bar) Min.inlet
Lead (cSt) (kW) 2 4 6 (bar)* 2 4 6 (bar)*
400 Qeff 13.50 13.20 12.97 -0.85 27.71 27.41 27.18 -0.82
Pe 0.28 0.33 0.38 0.76 0.85 0.95
400 Qeff 19.04 18.59 18.23 -0.85 39.20 38.74 38.39 -0.74
Pe 0.30 0.36 0.43 0.79 0.92 1.05
* Valid for liquids free from unresolved air or gas.
Selection guide 60 Hz
Size Visc. (lit/min) Speed: 1750 rpm Speed: 3500 rpm
& Diff. pressure (bar) Min.inlet Diff. pressure (bar) Min.inlet
Lead (cSt) (kW) 2 4 6 (bar)* 2 4 6 (bar)*
400 Qeff 16.44 16.14 15.91 -0.85 33.59 33.29 33.06 -0.78
Pe 0.37 0.43 0.48 0.99 1.11 1.22
400 Qeff 23.21 22.76 22.40 -0.85 47.54 47.08 46.73 -0.68
ACD6 1116.02 GB
4 www.imo.se
Pump dimensions
Pump ACD
Dimensions in mm (The counter flanges are accessories)
Fig. 1
Fig. 2
www.imo.se 5
Accessories
A bare shaft pump (fig. 3) can be ordered with the accessories in fig. 4–7.
Installation
The ACD-pump with counter flanges of the connections. The double assembly saves
weld neck type is mounted directly to an space and facilitates installation,
electric motor and has an angle bracket for maintenance, service and supervision. See
mounting horizontally, vertically or any Product Description for T4.
other attitude. Two pump units can also be For more information about installation
mounted to a double assembly on a com- read the Installation and Start-up manual
mon frame with inlet and outlet pipe for low pressure pumps.
6 www.imo.se
Sectional view
ACD 025, all models
flow out flow in
401
501 556
551
451
451
162
202
134
506 612
612A
601
Fig. 8
List of components
Pos No Denomination Pos No Denomination
1020 Power rotor 551 Rear cover
134 Locking screw 556 Gasket
162 Nylon sleeve socket 601 Valve cover
202 Idler rotor 602 Sealing washer
401 Pump body 605 O-ring
443 Drip nipple 612 Regulating screw
451 Screw 612A Retaining ring
501 Front cover 614 Valve piston
506 O-ring 615 Valve spring
509 Shaft seal
ACD6 1116.02 GB
www.imo.se 7
ZZZLPRVH
ȱDZȱ ǯȱǯȱ¡ȱŚŘŖşŖǰȱȱŗŘŜȱŗŚȱǰȱ
ȱ DZȱƸŚŜȱŞȱśŖȱŜŘŘȱŞŖŖǰȱ¡DZȱƸŚŜȱŞȱŜŚśȱŗśŖş