Professional Documents
Culture Documents
DATASHEET
POSSIBLE SUBSTITUTE PRODUCT
(NOT PIN-FOR-PIN) ISL8002, ISL8002A
EL7532 FN7435
Monolithic 2A Step-Down Regulator Rev 9.00
December 9, 2015
*Add -T7 suffix for 1k unit or -T13 suffix for 2.5k unit tape and reel • Li-Ion battery powered devices
options. Please refer to TB347 for details on reel specifications.
• ASIC/FPGA/DSP supplies
NOTE: These Intersil Pb-free plastic packaged products employ
special Pb-free material sets; molding compounds/die attach • Set top boxes
materials and 100% matte tin plate PLUS ANNEAL - e3 termination
finish, which is RoHS compliant and compatible with both SnPb and Typical Application Schematic
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed VS (2.5V to 5.5V) L1 VO
the Pb-free requirements of IPC/JEDEC J STD-020. VIN LX
1.8µH
R3 100
C1
VDD
Pinout 10µF
C2 C3
EL7532 10µF 0.1µF EL7532
(10 LD MSOP)
TOP VIEW
R5 100k
R1*
POR
1 SGND FB 10 124k C4
EN FB
470pF
2 PGND VO 9 R4 100k RSI R2 *
R6 100k
3 LX POR 8 100k
PGND
4 VIN EN 7 SGND VO
(1.8V @ 2A)
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
1. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications VDD = VIN = VEN = 3.3V, C1 = C2 = 10µF, L = 1.8µH, VO = 1.8V, unless otherwise specified.
VLINEREG Line Regulation (Note 2) VIN = 2.5V to 6V, IOUT = 2A, VOUT = 1.8V 0.1 %/V
VLOADREG Load Regulation (Note 2) VIN = 3.3V, VOUT = 1.8V, IOUT = 0 to 2A 0.5 %
AC CHARACTERISTICS
Pin Descriptions
PIN NUMBER PIN NAME PIN FUNCTION
8 POR Power on reset open drain output; Leave open if not used
10 FB Voltage feedback input; connected to an external resistor divider between VO and SGND for variable
output
Block Diagram
5 VDD
VO
9
10pF 4
VIN
124k
FB 5M
10 -
+ PWM
COMPEN- +
SATION -
PWM P-DRIVER
100k COMPARATOR
LX 1.8µ
CLOCK RAMP CONTROL
LOGIC 1.8V
1.5MHz GENERATOR 3
2A
7 EN
EN
SOFT-
10µF START 10µF
N-DRIVER
UNDER-
+ VOLTAGE PGND
BANDGAP 2
– LOCKOUT
2.5V REFERENCE 100k
TO 5V TEMPERATURE POR
1 SGND SENSE PG
8
POR
6 RSI
80 80
EFFICIENCY (%)
EFFICIENCY (%)
60 VO = 1.2V VO = 3.3V 60
VO = 1.2V
40 40 VO = 2.5V
VO = 1.8V
VO = 1.8V
20 20
100 1.0
IO = 2A
80 0.6 VO = 0.8V
VO CHANGES (%)
EFFICIENCY (%)
60 0.2
VO = 1.8V
40 -0.2 VO = 2.5V
VO = 1.2V
VO = 3.3V
20 -0.6
1.0 1.0
0.6 0.6
VO CHANGES (%)
VO CHANGES (%)
-0.6 -0.6
-1.0 -1.0
0 0.5 1.0 1.5 2.0 2.5 0 0.5 1.0 1.5 2.0 2.5
1.0
VIN 100mV/d
VO = 0.8V
0.5
VO CHANGES (%)
iL 0.5A/d
VO 10mV/d
-1.0
0 0.5 1.0 1.5 2.0 2.5
IOUT (A) 1µs/d
FIGURE 7. LOAD REGULATION @ VIN = 2.5V FIGURE 8. LOAD REGULATION @ VIN = 2.5V
VIN VIN
(1V/d) (2V/d)
VO
IIN (2V/d)
(0.5A/d)
POR
(2V/d)
VO
(1V/d)
0.5ms/d 50ms/d
VIN
(2V/d)
VO
50mV/d
VO
(2V/d)
2A
RSI
(2V/d) IO
POR
(2V/d) 0.1A
50ms/d 0.5ms/d
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make
sure that you have the latest revision.
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
A2
GAUGE
PLANE
0.25
A1 L
3° ±3°
DETAIL X