Professional Documents
Culture Documents
myoutdoorplans.com/animals/free-deer-stand-plans/
June 20,
2014
This step by step project is about free deer stand plans. If you want to learn more about
building a basic wooden deer stand that can be disassembled and moved from one
location to the other, we recommend you to pay attention to the instructions. Work with
attention and adjust the size and the design of the portable deer stand to suit your
needs and tastes.
There are several aspects that any person should take into account before starting the
woodworking project. First of all, you need to use weather-resistant lumber, such as
cedar, pine or redwood. Drill pocket holes at both ends of the components, if you want
to lock them together tightly. In addition, add wood glue to the joints and check if the
corners are right-angled. Plan everything from the very beginning, if you want to get a
professional result.
1/10
Building a deer stand
2/10
E – 1 piece of 3/4″ plywood – 48″ x 79 1/2″ long FACE
F – 2 pieces of 2×4 lumber – 83 1/2″ long, 3 pieces -41″ long FACE
G – 1 piece of 3/4″ plywood – 48″ x 73″ long BACK
H – 2 pieces of 2×4 lumber – 77″ long, 3 pieces -41″ long BACK
I – 1 piece of 3/4″ plywood – 41″ x 42 1/2″ long, 2 pieces of 2×4 lumber – 41″ long, 2
pieces – 35 1/2″ long DOOR
J – 1 piece of 3/4″ plywood – 48 1/2″ x 57 1/2″ long, 2 pieces of 2×4 lumber – 36″
long ROOF
One day
3/10
Building the floor frame
The first step of the woodworking project is to build the floor for the deer stand. As you
can easily notice in the project, we recommend you to cut the components at the right
size, after taking accurate measurements.
Drill pilot holes through the perimeter joists and insert 2 1/2″ screws into the
perpendicular components. Make sure the corners are right-angled and leave no gaps
between the components.
The next step of the woodworking project is to cut the floor out of 3/4″ plywood at the
right size. Smooth the cut edges with fine-grit sandpaper and attach it over the joists.
Drill pilot holes along the edges and secure it to the joists with 1 1/4″ galvanized screws.
Leave no gaps between the components and check if the edges are flush.
Continue the project by building the sides of the deer stand. In order to get a
professional result, we recommend you to mark the cut lines over the 3/4″ plywood
sheet and to get the job done with a circular saw.
Drill the starting holes to create the windows inside the plywood panels. Afterwards, use
a jigsaw to get the job done, but make sure the blade goes over the cut lines.
4/10
Attaching the frame to sides
In order to enhance the rigidity of the side walls, we recommend you to attach 2×4 studs
over the sheet. As you can easily notice in the diagram, we recommend you to cut the
components at the right size and to attach them over the sheet with 2″ screws.
Take accurate measurements and drill pilot holes before inserting the screws, to prevent
the wood from splitting. Add glue to the joints to enhance the bond of the components.
Attach the sides to the floor, making sure you leave no gaps between the components.
Plumb the sides with a spirit level and lock the panels to the floor by inserting 2″ screws.
Front face
Building the front face for the portable deer stand is easy, but you need to take accurate
measurements and to get the job done with a proper saw. Make sure the corners are
right-angled and the plywood sheets are in a good condition. Smooth the exposed edges
before continuing the project.
5/10
Attaching the frame to the front face
Next, attach the 2×4 studs to the plywood panel, in order to get a professional result. Cut
the components at the right size and attach them to the plywood face using 2″
galvanized screws. Add glue to the joints and make sure the edges are flush. In addition,
you could lock the studs one to another, by drilling pocket holes and inserting 2 1/2″
screws.
Build the back of the deer stand in the same manner described above. Work with
attention and take accurate measurements. Smooth the edges with sandpaper and
make sure the corners are right-angled.
Attach the 2×4 studs over the plywood panel, as described in the panel. Drill pilot holes
and insert 2″ galvanized screws into place. In addition, add glue to the joints and remove
the excess using a damp cloth.
6/10
Building the door
Use the plywood piece that was cut out of the back wall and use it for making the door of
the deer stand. Smooth the edges with sandpaper and remove the residues with a
vacuum cleaner. Make sure the plywood panel is in a good condition and the corners are
right-angled.
Attach the 2×4 framing to the door panel, as described in the diagram. Work with
attention and leave no gaps between the components. Check if the edges are flush and
leave no gaps between the components. Add glue and pre-drill holes before inserting the
screws, to prevent the wood from splitting.
One of the last steps of the project is to attach the door to the deer stand. As you can
easily notice in the diy diagram, we recommend you to fit the door into place and to
attach it to the back face of the structure by using several metal hinges.
7/10
Top Tip: Make sure the door opens and closes properly before continuing the outdoor
project. Fit a door latch inside the door, to lock it properly. Smooth the edges with
sandpaper.
Building the roof of the deer stand is a straight forward process, but you need to take
accurate measurements before assembling the components together. In order to get a
professional result, we recommend you to cut the components at the right size.
Drill pilot holes through the plywood and insert 2 1/2″ screws into the 2×4 supports. Align
everything with attention and leave no gaps between the components.
Last but not least, you should take care of the finishing touches. Therefore, fill the holes
with wood putty and let the compound to dry out for several hours. Smooth the surface
with medium-grit sandpaper along the wood grain.
Top Tip: Apply several coats of stain or paint to enhance the look of the portable deer
stand and to protect the components from decay. Check out the rest of the projects to
see more related projects.
This project was about free deer stand plans. If you want to see more outdoor plans, we
recommend you to check out the rest of the projects. Don’t forget to share our projects
with your friends, by using the social media widgets.
8/10
9/10
10/10