Professional Documents
Culture Documents
meter can measure AC/DC voltage, AC/DC current, the trigger to loosen clamp
6
and temperature, etc. tightened again conductive object of which voltage exceeds
measured circuit then Figure 7
3
To set knob.
remove probe from input
end after all measurement operations.
Please open the package box and take instrument users from touching any 1 Please place function knob to
out. Please check if following items are deficient or dangerous area. To select key functions. 6. Capacitance measurement ( ) (See
damaged or not. 7. Clamp head: It is a device to The clamp meter defaults at Figure 8)
1. Operating Manual 1 pc measure AC/DC current to Figure 1 DC Voltage and auto-ranging
convert current to voltage. Single Warning: Be sure to cut off circuit power and
2. Test Probes 1 pair mode. Press REL △ to
conductor of measured current must pass through access relative mode. discharge residual charge of all capacitors
3. Temperature probe 1 pc
center of clamp head perpendicularly; before load connection.
4. Guarantee certificate 1 pc To connect load. V
8.Temperature measurement ( ) (See IX. Technical Indicators (6) Capacitance ( ) sensitive device, Hall element will be sensitive to
Figure 10) Range Resolution Accuracy Overload protection heat and mechanical stress to different extents
1.General specification
4nF 0.001nF in addition to magnetic sensitivity. Collision will
LCD display: 4000 counts;
To set knob. 40nF 0.01nF cause short-term reading variation.
To place function knob to Polarity display: Automatic display; 400nF 0.1nF AC conversion type:
(4.0%+3) 600Vp
Overload display: To display OL or -OL , 4µF 0.001µF AVG response; RMS value for sinewave input.
To select functions.
Low Battery Indication: shows as battery 40µF 0.01µF
X. Maintenance(See Figure 13)
To connect load. 100µF 0.1µF (5.0%+10)
voltage is less than required working voltage.
Sampling rate: 3 times/second; Warning: Please remove testing rod before
To measure under RELATIVE measurement mode;
Sensor category: Hall affect sensor for DC/AC opening bottom cover to avoid electric shock.
measurement; (7) Frequency (Hz) 1. General maintenance
Error of testing position: 1.0% of additional Range Resolution Accuracy Overload protection A. The clamp meter must be repaired and served
reading error may be caused if failing to place 10Hz 0.001Hz by qualified professional repair personnel or
measured source to center of clamp head during 100Hz 0.01Hz designated repair department.
current measurement; 1kHz 0.1Hz B. To clean the shell periodically by dry cloth.
Figure 10 (0.5%+3) 600Vp
10kHz 1Hz However, it is not allowed to use detergent
Shock-resistant: pass 1m drop test; 100kHz 10Hz
1) LCD will display OL if failing to insert with abrasive or solvent .
Max.clamp Opening : 28mm diameter; 1MHz 100Hz
temperature sensor. Clamp meter will display
Max. Tested Conductor: 26mm diameter; 10MHz 1kHz (Reading is only for reference.)
current indoor temperature after user inserting
temperature sensor. Influence of electromagnetic field: Device used Sensitivity: 300mV rms if 100kHz;
2) The protection for the temperature range is near electromagnetic field may display unstable 600mV rms if 100kHz;
1KΩ resistor(R59). any conductor with voltage or incorrect reading; 800mV rms if 1MHz;
present cannot be inserted into input jack to 2.Environment limitation
avoid. Indoor use Input amplitude a:
9. DC current measurement ( ) (See The altitude height: 2,000m 10Hz~100kHz : 30V rms ≥ a ≥300mV rms
Figure 11) Safety rules: ICE 1010-1 CAT.II 600V 100kHz~10MHz : 30V rms ≥ a ≥600mV rms
To set knob. CAT.III300V
Pollution degree: 2 (8) Temperature ( )
To place function knob to 40A or 600A
Operation temperature & humidity: 0 to 30 Range Accuracy Overload protection
To select functions. (not more than 80%R.H.) -40 ~0 (8%+5)
The meter defaults at DC Current Mode. -40 ~ Plug-in resistance
30 to 40 (not more than 75%R.H.) 1,000 0 ~400 (2.5%+3)
of 1K
To connect load. 40 to 50 (not more than 45%R.H.)
400 ~1,000 (3.0%+3)