Professional Documents
Culture Documents
5
Service Manual
Contents
1. Introduction ..................................................................................................... 3
1.1 Objective .................................................................................................... 3
1.2 General Safety notice ................................................................................... 3
1.3 Use Instruction ............................................................................................ 3
2. Technology summarize ..................................................................................... 4
2.1 Description of main board component map ..................................................... 4
2.2 MT6589 circuit system ................................................................................. 6
2.3 Base band circuit ......................................................................................... 7
3. Trouble Shooting ............................................................................................. 8
3.1 Fail to startup/power on ................................................................................ 8
3.2 Fail to charge .............................................................................................. 9
3.3 Fail to display ........................................................................................... 10
3.4 Fail to call................................................................................................. 11
3.5 Speaker no sound....................................................................................... 12
3.6 Earphone fail............................................................................................. 13
3.7 Vibrator fail .............................................................................................. 14
3.8 Side key fail .............................................................................................. 15
3.9 Failure to identify SIM card ........................................................................ 16
3.10 Camera fail ............................................................................................. 17
3.11 Failure to read T-flash card ........................................................................ 18
4. BGA related GND or no function pad ............................................................... 19
4.1 CPU and memory pin map .......................................................................... 19
4.2 PMU pin map ............................................................................................ 19
4.3 WIFI ....................................................................................................................... 20
4.4 TRANSEIVER ....................................................................................................... 20
1. Introduction
1.1 Objective
The manual is not a general publication but only edited for experienced technicians. The
main purpose is to provide the basic foundation for the electrical & mechanical
maintenance.
Processing features:
◆ High-performance ARM CORTEX A7 1.2GHz application processor :
1) ARM architecture v7
2) 32 KB instruction and 32 KB data cache
3) 8-stage In-order pipeline with dynamic branch prediction
4) Supports the ARM and Thumb instruction sets, and Jazelle technology to enable direct
execution of Java byte-codes
3. Trouble Shooting
3.1 Fail to startup/power on
The following conditions may cause boot fail: battery low, battery connector is damaged or
bad welding, components bad weld/short-circuit or damaged
First, change a fully charged battery test, still startup fail, check battery connector ok or not,
if connector damaged change a new one;
Second, connect to DC power supply, if the boot process is no current, we should check
power key solder ok or not;
Third, if the boot current is very small and cannot maintain ,connect the power on test point
to GND, then check below voltage in sequence, VPROC_PMU,VCORE_PMU,VM_PMU,
VRF18_PMU,VIO18_PMU,VIO28_PMU,VEMC_3V3_PMU,VEMC_1V8_PMU ok not.
Fourth, if the current stay in 40mA, we should check the circuit around flash, when CPU
calling program from flash fail, the current will stay in 40mA, re-download the software or
change a new flash or CPU.
Fail to power on
N
Check if the battery Change
is OK. battery
Y
N Resold
Check if battery
connects solder ok connect
Re-download Y
OK
Software
N
Y
Resold or replace OK
U1082
N
Y
Resold or replace OK
U300
3.2 Fail to charge
Check charging circuit related component, check below information in sequence:
First, checks whether boot normal use the battery, if not check battery connector solder ok
or not;
Second, check USB connector on board solder ok or not;
Third, check T1110 whether reverse, check C1321resistance is very big or not, check
B1110,B1111 solder ok or not;
Fourth, check U2 solder ok or not, re-hot U2 or change a new one.
No charge
N
Check J1702 Change a new
solder OK or not? one
Y
N Change T1110
or C1321
Check
T1110&C1321
Check B1110,B1111 N
and Q601 ok or not? Change related
component
N
Check U2 Hot or change U2.
3.3 Fail to display
The screen dose not shines or shows white:
First, use DC power supply to start-up, check the board whether power on normal, ensure
main board can power on normal
Second, check LCD module, change a new module, check whether can display normal,
Third, check L1090, D1510 solder ok or not
Fourth, use oscilloscope to test LCD_BACKLIGHT_EN, check it whether high, if not, check
R1210 resistance, U300solder ok or not, re-hot U300or check a new one.
No display
N
Is the LCM well?
Change LCM
U1201 Y Change
reverse or U1201
damaged
L1090, D1510 Y
NC or not Add L1090 or D1510
Change or Y Change
re-solder U300
U300
OK
3.4 Fail to call
When call with somebody, we cannot hear what he says or he cannot hear what we say:
This fail may cause by receiver or microphone fail, it can test in factory mode,
type“*#*#9375#*#*” enter factory mode, Transmitter/Receiver test, if ok, it may RF fail, if fail,
we need to make sure is receiver or microphone fail.
Call 112, if can hear voice, it may microphone problem, check microphone related
circuit ,check R801, R802, R808, R809 and T801,T802 solder ok or not, if all ok, change a
new microphone, also fail, check CPU, re-hot or change a new one.
Call 112, if cannot hear voice, it may receiver problem, change a new receiver, check R812,
R813 and C817,C818 ok or not, if ok, check CPU, re-hot or change a new one.
Y
Can hear sound in Check RF
Factory mode?
N
N Check
Rework Check
Related Related Rework
uncorrected R C TVS? uncorrected
component R, C, TVS?
Y component
Y
Y
N N
Hot or change Check Check Hot or change
new one U300? U300? new one
3.5 Speaker no sound
First, check speaker ok or not, change a new one;
Second, check B1330、B1333、C1780、C1781、C1782, solder ok or not;
Third, check U2, re-hot or change a new one.
No sound
N
Is speaker OK? Replace
Speaker
Y
Are B1910, B1911
NC or not? ADD B1910,B1911
N
Check T1912, Re-solder uncorrected
T1913, C1929, component
C1930, and C2001
ok or not?
Y
N
Check U1001 Hot or change U1001
3.6 Earphone fail
No sound in
earphone
N
Is earphone Replace
connector OK? earphone
Is J601 soldering N
Re-solder J601
well?
Related R, N Re-solder
C right? uncorrected R C
Hot or
OK
change
U300
3.7 Vibrator fail
Motor doesn’t work
N
Supply 3.3V for motor, Change a
test motor can work or new Motor
not
Check related R, C OK N
Change uncorrected
or NOT, Check D1401 component
reverses or not
Hot U2 or Change a OK
new one
3.8 Side key fail
N
Re-solder or
Is key switch soldering
OK? change new
one
Y
Check U2 Re-sold or change U2
3.9 Failure to identify SIM card
SIM is not identified
Touch Pin is N
Clean SIM socket
clean?
Y
Change a new SIM is damaged.
SIM to try Replace it
N
Is SIM socket Change a new one.
good?
N
Check if VSIM1/ Change U2
VSIM2 are OK?
Camera fail
N
Is camera connector Re-solder or
soldering well? change new
one
Check camera ok or N
Change a new
not? camera
Y T-F card is
Change a new
TF-card to test damaged. Replace
it
N
Check T flash Re-solder it or
card socket change new one
ok or not?
N
Check TVS
Solder it correct
reverse or not?
N
Check VDD Hot U2 or
OK or not? change new
one
N
Check each Hot U300
signal OK or not? or change
new one
4. BGA related GND or no function pad
Red--------no function pad
White------GND pad
4.4 TRANSEIVER