Professional Documents
Culture Documents
PLA-2 2 5 0 PLA-2350
PLA-2 4 5 0 PLA-2550
PLA-2650 PLA-2750
PLA-2850
Two Channel High
Per formance Power Amplifier
PLA- 4 1 9 P L A - 4 1 5 0
PLA-4250 PLA-4350
Four Channel High
Per formance Power Amplifier
PLA-4300D
Class-D Mono Block Power Amplifier
congratulations...
on your purchase of a Pyle Gear X Series amplifier.
This amplifier extends the Pyramid tradition into
a totally new series of amps, designed from the
ground up to deliver the power, performance and
flexibility the modern car audio enthusiast demands.
PLA-219
High Performance 240 Watt 2 Channel Amplifier
PLA-419
High Performance 400 Watt 4 Channel Amplifier
PLA-2150
High Performance 600 Watt 2 Channel
Bridgeable MOSFET Amplifier
· 120 Watts x 2 Output · 100 Watts x 4 Output · 300 Watts x 2 Output
· Variable Input Level (Gain) Control · Variable Input Level (Gain) Control · 600 Watts x 1 Bridged Output
· Remote Turn On/Off · Remote Turn On/Off · Variable Hi/Lo Electronic Crossover Network
· Gold Plated RCA Inputs
· High Level MOLEX Input
· Gold Plated RCA Inputs
· High Level MOLEX Input
· Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
2
· Power ON LED Indicator · Power ON LED Indicator · Remote Turn On/Off
· S/N Ratio: > 95 dB · S/N Ratio: > 95 dB · Gold Plated RCA Inputs
· THD: <0.04% · THD: <0.04% · High Level MOLEX Input
· Thermal Protection · Thermal Protection · Power ON LED Indicator
· Overload Protection · Overload Protection · LED Protection Indicator
· Short Circuit Protection · Short Circuit Protection · S/N Ratio: > 95 dB
· Anti-Thump Turn-On · Anti-Thump Turn-On · THD: <0.04%
· Thermal Protection
· Overload Protection
· Short Circuit Protection
· Anti-Thump Turn-On
general features
PLA-2250
High Performance 1000 Watt 2 Channel
PLA-2350
High Performance 1200 Watt 2 Channel
PLA-2450
High Performance 1400 Watt 2 Channel
Bridgeable MOSFET Amplifier Bridgeable MOSFET Amplifier Bridgeable MOSFET Amplifier
· 500 Watts x 2 Output · 600 Watts x 2 Output · 700 Watts x 2 Output
· 1000W x 1 Bridged Output · 1200W x 1 Bridged Output · 1400W x 1 Bridged Output
· Variable Hi/Lo Electronic Crossover Network
· Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Hi/Lo Electronic Crossover Network
· Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Hi/Lo Electronic Crossover Network
· Variable Bass Boost (0 - +18 dB @ 60Hz)
3
· Variable Input Level (Gain) Control · Variable Input Level (Gain) Control · Variable Input Level (Gain) Control
· Remote Turn On/Off · Remote Turn On/Off · Remote Turn On/Off
· Gold Plated RCA Inputs · Gold Plated RCA Inputs · Gold Plated RCA Inputs
· High Level MOLEX Inputs · High Level MOLEX Inputs · High Level MOLEX Inputs
· Power ON LED Indicator · Power ON LED Indicator · Power ON LED Indicator
· LED Protection Indicator · LED Protection Indicator · LED Protection Indicator
· Remote Bass Boost · Remote Bass Boost · Remote Bass Boost
· S/N Ratio: > 95 dB · S/N Ratio: > 95 dB · S/N Ratio: > 95 dB
· THD: <0.04% · THD: <0.04% · THD: <0.04%
· Thermal Protection · Thermal Protection · Thermal Protection
· Overload Protection · Overload Protection · Overload Protection
· Short Circuit Protection · Short Circuit Protection · Short Circuit Protection
· Anti-Thump Turn-On · Anti-Thump Turn-On · Anti-Thump Turn-On
general features
PLA-2550
High Performance 1600 Watt 2 Channel
PLA-2650
High Performance 1800 Watt 2 Channel
PLA-2750
High Performance 2400 Watt 2 Channel
Bridgeable MOSFET Amplifier Bridgeable MOSFET Amplifier Bridgeable MOSFET Amplifier
· 800 Watts x 2 Output · 900 Watts x 2 Output · 1200 Watts x 2 Output
· 1600 Watts x 1 Bridged Output · 1800 Watts x 1 Bridged Output · 2400 Watts x 1 Bridged Output
· Variable Hi/Lo Electronic Crossover Network · Variable Hi/Lo Electronic Crossover Network · Variable Hi/Lo Electronic Crossover Network
· Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
· Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
· Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
4
· Remote Turn On/Off · Remote Turn On/Off · Remote Turn On/Off
· Gold Plated RCA Inputs · Gold Plated RCA Inputs · Gold Plated RCA Inputs
· High Level MOLEX Input · High Level MOLEX Input · High Level MOLEX Input
· Power ON LED Indicator · Power ON LED Indicator · Power ON LED Indicator
· LED Protection Indicator · LED Protection Indicator · LED Protection Indicator
· Remote Bass Boost · Remote Bass Boost · Remote Bass Boost
· S/N Ratio: > 95 dB · S/N Ratio: > 95 dB · S/N Ratio: > 95 dB
· THD: <0.04% · THD: <0.04% · THD: <0.04%
· Thermal Protection · Thermal Protection · Thermal Protection
· Overload Protection · Overload Protection · Overload Protection
· Short Circuit Protection · Short Circuit Protection · Short Circuit Protection
· Anti-Thump Turn-On · Anti-Thump Turn-On · Anti-Thump Turn-On
general features
PLA-2850
High Performance 4000 Watt 2 Channel
PLA-4150
High Performance 1000 Watt 4 Channel
PLA-4250
High Performance 1400 Watt 4 Channel
Bridgeable MOSFET Amplifier Bridgeable MOSFET Amplifier Bridgeable MOSFET Amplifier
· 2000 Watts x 2 Output · 250 Watts x 4 Output · 350 Watts x 4 Output
· 4000 Watts x 1 Bridged Output · 500 Watts x 2 Bridged Output (250Wx2+500Wx1) · 700 Watts x 2 Bridged Output (350Wx2+700Wx1)
· Variable Hi/Lo Electronic Crossover Network · Dual Variable Hi/Lo Electronic Crossover Network · Dual Variable Hi/Lo Electronic Crossover Network
· Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
· Dual Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
· Dual Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
5
· Remote Turn On/Off · Remote Turn On/Off · Remote Turn On/Off
· Gold Plated RCA Inputs · Gold Plated RCA Inputs · Gold Plated RCA Inputs
· High Level MOLEX Input · High Level MOLEX Input · High Level MOLEX Input
· Power ON LED Indicator · Power ON LED Indicator · Power ON LED Indicator
· LED Protection Indicator · LED Protection Indicator · LED Protection Indicator
· Remote Bass Boost · S/N Ratio: > 95 dB · Remote Bass Boost
· S/N Ratio: > 95 dB · THD: <0.04% · S/N Ratio: > 95 dB
· THD: <0.04% · Thermal Protection · THD: <0.04%
· Thermal Protection · Overload Protection · Thermal Protection
· Overload Protection · Short Circuit Protection · Overload Protection
· Short Circuit Protection · Anti-Thump Turn-On · Short Circuit Protection
· Anti-Thump Turn-On · Tri-Mode Configurable · Anti-Thump Turn-On
· Tri-Mode Configurable
general features
PLA-4350
High Performance 2000 Watt 4 Channel
PLA-4300D
4000W Mono Block MOSFET Amplifier
Bridgeable MOSFET Amplifier
· 500 Watts x 4 Output · Mono Block Subwoofer Amplifier
· 1000W x 2 Bridged Output (500W x 2+1000W x 1) · 1 Ohm Stable
· Dual Variable Hi/Lo Electronic Crossover Network · MOSFET Power Supply
· Dual Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
· PWM (Pulse-Width-Modulation) System
· Glass Epoxy PCB
6
· Remote Turn On/Off · Gold Plated RCA Inputs for Line Input & Bypass Output.
· Gold Plated RCA Inputs · Gold Plated Terminals for Speaker Output and Power Input.
· High Level MOLEX Inputs · Thermal, Overload and Short Protection
· Power ON LED Indicator · Variable Sub-sonic Filter (15Hz~40Hz, 24dB/Octave)
· LED Protection Indicator · Variable Low-pass Filter (20Hz~250Hz, 24dB/Octave)
· Remote Bass Boost · Phase Control 0-180 degree
· S/N Ratio: > 95 dB · Remote Bass Control
· THD: <0.04% · Input Impedance : 10K Ohms
· Thermal Protection · Soft Turn On/Off
· Overload Protection · Advanced Protection Circuitry
· Short Circuit Protection · S/N Ratio:>90dB
· Anti-Thump Turn-On · Heavy Duty Power Coated Heatsink
· Tri-Mode Configurable
features and controls
2 ch amp PLA-219
PLA-219
power fuse
features and specifications
2 ch amp PLA-219
input level control use this control to match the outputs of your head unit to the amplifier. output power @ 14.4v DC, 1KHz
Starting with your head unit set at about the 2 o’clock position, increase
the amp level control until distortion begins to occur, and reduce slightly RMS Power @ 4 Ohms 30 Watts x 2
from this point. Maximum Power Output 120 Watts x 2
low level inputs this amp features gold-plated RCA input jacks for high impedance input. frequency response 15 Hz-30 KHz
Use these with car stereo output which uses RCA-type connector cables.
high level inputs if your car stereo lacks RCA-type output jacks, you may connect speaker input impedance
output leads to these input connectors.
PLA-419
power LED
power fuse
features and specifications
4 ch amp PLA-419
input level control use this control to match the outputs of your head unit to the amplifier. output power @ 14.4v DC, 1KHz
Starting with your head unit set at about the 2 o’clock position, increase
the amp level control until distortion begins to occur, and reduce slightly RMS Power @ 4 Ohms 30 Watts x 4
from this point. Maximum Power Output 100 Watts x 4
low level inputs this amp features gold-plated RCA input jacks for high impedance input. frequency response 15 Hz-30 KHz
Use these with car stereo output which uses RCA-type connector cables.
high level inputs if your car stereo lacks RCA-type output jacks, you may connect speaker input impedance
output leads to these input connectors.
power fuse
features and specifications
2 ch amp PLA-2150 • PLA-2250
PLA-2350 • PLA-2450
output power @ 14.4v DC, 1KHz PLA-2150 PLA-2250 PLA-2350 PLA-2450
crossover mode selector when used with normal, full range systems, set this switch to “FULL.” If
you wish to use the internal crossover to power a driver of specific frequency RMS Power @ 4 Ohms 40 Watts x 2 75 Watts x 2 75 Watts x 2 100 Watts x 2
range, use the “LOWPASS” or “HIGHPASS” settings. RMS Power @ 2 Ohms 60 Watts x 2 125 Watts x 2 125 Watts x 2 175 Watts x 2
Maximum Power Output 300 Watts x 2 500 Watts x 2 600 Watts x 2 700 Watts x 2
input level control use this control to match the outputs of your head unit to the amplifier.
Starting with your head unit set at about the 2 o’clock position, increase
the amp level control until distortion begins to occur, and reduce slightly frequency response 15 Hz-30 KHz
from this point.
input impedance
low pass frequency control when the crossover selector switch is in “low pass” mode, this control low level inputs
sets the upper frequency limit for audio program sent to the speakers.
10K Ohms
high level inputs 100 Ohms
high pass frequency control when the crossover selector switch is in “high pass” mode, this control
sets the lower frequency limit for audio program sent to the speakers. input sensitivity
12
Remote Bass Boost Plug in the Remote Bass Boost Control wire in here.(PLA-2150 without)
low level inputs 250mV
high level inputs 2.5V
bass boost level control this control permits adjustment of the bass level up to an increase of
approximately 18 dB. power supply voltage 14.4V DC Neg. Ground (10.5-16V)
low level inputs this amp features gold-plated RCA input jacks for high impedance input. matching speaker impedance
Use these with car stereo output which uses RCA-type connector cables.
stereo mode 2-4 Ohms
high level inputs if your car stereo lacks RCA-type output jacks, you may connect speaker bridged mode 4-8 Ohms
output leads to these input connectors.
maximum current draw 15A 15A 20A 30A
power LED this indicator is illuminated when power is applied.
protection LED this indicator is illuminated when built-in protection circuitry is activated. dimensions (W x H x L)
mm 281 x 59 x 209 281 x 59 x 280 281 x 59 x 305 281 x 59 x 343
power fuse the fuse protects the amplifier and your car’s electrical system from short inches 11.06 x 2.32 x 8.25 11.06 x 2.32 x 11 11.06 x 2.32 x 12 11.06 x 2.32 x 13.5
circuit conditions.
power terminals use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
speaker connections these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
features and controls
2 ch amp PLA-2550 • PLA-2650
PLA-2750 • PLA-2850
PLA-2850
high pass frequency control
low pass frequency control high level inputs
13
bass boost level low level inputs
crossover mode selector input level control
power fuse
features and specifications
2 ch amp PLA-2550 • PLA-2650
PLA-2750 • PLA-2850
crossover mode selectors when used with normal, full range systems, set these switches to “FULL.” output power @ 14.4v DC, 1KHz PLA-2550 PLA-2650 PLA-2750 PLA-2850
If you wish to use the internal crossovers to power a driver of specific
frequency range, use the “LOWPASS” or “HIGHPASS” settings. RMS Power @ 4 Ohms 125 Watts x 2 150 Watts x 2 200 Watts x 2 300 Watts x 2
RMS Power @ 2 Ohms 200 Watts x 2 225 Watts x 2 290 Watts x 2 450 Watts x 2
input level controls use these controls to match the outputs of your head unit to the amplifier. Maximum Power Output 800 Watts x 2 900 Watts x 2 1200 Watts x 2 2000 Watts x 2
Starting with your head unit set at about the 2 o’clock position, increase
the amp level controls until distortion begins to occur, and reduce slightly
from this point. frequency response 15 Hz-30 KHz
low pass frequency controls when one or both of the crossover selector switches is in “low pass” input impedance
mode, one can set the upper frequency limit for audio program sent to
the speakers. low level inputs 10K Ohms
high level inputs 100 Ohms
high pass frequency controls when the one or both of crossover selector switch is in “high pass” mode,
one can set the lower frequency limit for audio program sent to the
speakers.
input sensitivity
low level inputs 250mV
14
Remote Bass Boost Plug in the Remote Bass Boost Control wire in here. high level inputs 2.5V
bass boost level controls this control permits adjustment of the bass level up to an increase of power supply voltage 14.4V DC Neg. Ground (10.5-16V)
approximately 18 dB in either or both pairs of channels.
low level inputs this amp features gold-plated RCA input jacks for high impedance input.
matching speaker impedance
Use these with car stereo output which uses RCA-type connector cables. stereo mode 2-4 Ohms
bridged mode 4-8 Ohms
high level inputs if your car stereo lacks RCA-type output jacks, you may connect speaker
output leads to these input connectors.
maximum current draw 20 A 20 A x 2 25 A x 2 30 A x 2
power LED this indicator is illuminated when power is applied.
dimensions (W x H x L)
protection LED this indicator is illuminated when built-in protection circuitry is activated. mm 281 x 59 x 381 281 x 59 x 432 281 x 59 x 482 281 x 59 x 532
power fuse the fuse protects the amplifier and your car’s electrical system from short inches 11.06 x 2.32 x 15 11.06 x 2.32 x 17 11.06 x 2.32 x 19 11.06 x 2.32 x 21
circuit conditions.
power terminals use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
speaker connections these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
features and controls
4 ch amp PLA-4150 • PLA-4250 • PLA-4350
PLA-4250
ch 3/4 input level control ch 1/2 input level control
PLA-4350 ch 3/4 high level inputs ch 1/2 high level inputs
15
ch 3/4 low level inputs ch 1/2 low level inputs
ch 3/4 crossover mode selector switch ch 1/2 crossover mode selector switch
ch 3/4 bass boost level control ch 1/2 bass boost level control
ch 3/4 low pass frequency control ch 1/2 low pass frequency control
ch 3/4 high pass frequency control ch 1/2 high pass frequency control
power LED
protection LED
power fuse
features and specifications
4 ch amp PLA-4150 • PLA-4250 • PLA-4350
dual crossover mode selectors when used with normal, full range systems, set these switches to “FULL.” output power @ 14.4v DC, 1KHz PLA-4150 PLA-4250 PLA-4350
If you wish to use the internal crossovers to power a driver of specific
frequency range, use the “LOWPASS” or “HIGHPASS” settings. RMS Power @ 4 Ohms 35 Watts x 4 50 Watts x 4 75 Watts x 4
RMS Power @ 2 Ohms 55 Watts x 4 75 Watts x 4 115 Watts x 4
dual input level controls use these controls to match the outputs of your head unit to the amplifier. Maximum Power Output 250 Watts x 4 350 Watts x 4 500 Watts x 4
Starting with your head unit set at about the 2 o’clock position, increase
the amp level controls until distortion begins to occur, and reduce slightly
from this point. frequency response 15 Hz-30 KHz
dual low pass frequency controls when one or both of the crossover selector switches is in “low pass” input impedance
mode, one can set the upper frequency limit for audio program sent to
the speakers. low level inputs 10K Ohms
high level inputs 100 Ohms
dual high pass frequency controls when the one or both of crossover selector switch is in “high pass” mode,
one can set the lower frequency limit for audio program sent to the
speakers.
input sensitivity
low level inputs 250mV
16
CH 3/4 Remote Bass Boost Plug in the Remote Bass Boost Control wire in here.(PLA-4150 without) high level inputs 2.5V
dual bass boost level controls this control permits adjustment of the bass level up to an increase of power supply voltage 14.4V DC Neg. Ground (10.5-16V)
approximately 18 dB in either or both pairs of channels.
low level inputs this amp features gold-plated RCA input jacks for high impedance input.
matching speaker impedance
Use these with car stereo output which uses RCA-type connector cables. stereo mode 2-4 Ohms
bridged mode 4-8 Ohms
high level inputs if your car stereo lacks RCA-type output jacks, you may connect speaker
output leads to these input connectors.
maximum current draw 20 A 30 A 20 A x 2
power LED this indicator is illuminated when power is applied.
dimensions (W x H x L)
protection LED this indicator is illuminated when built-in protection circuitry is activated. mm 281 x 59 x 305 281 x 59 x 381 281 x 59 x 432
power fuse the fuse protects the amplifier and your car’s electrical system from short inches 11.06 x 2.32 x 12 11.06 x 2.32 x 15 11.06 x 2.32 x 17
circuit conditions.
power terminals use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
speaker connections these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
features and controls
Class-D MONO BLOCK AMPLIFIER PLA-4300D
power LED
PLA-4300D protection LED
17
line level outputs
remote bass boost line level inputs
input level control
low pass frequency control sub sonic control
phase shift switch
speaker connections
power fuse power terminals
features and specifications
Class-D MONO BLOCK AMPLIFIER PLA-4300D
Class-D design Low-frequency information for subwoofer only.High efficient power output power @ 14.4v DC, 50Hz PLA-4300D
power supplies Stiffly regulated PWM power supplies. MOSFET switches maintain RMS Power at @ 4 Ohms 400W MONO
rated power over a wide range of battery voltages. RMS Power at @ 2 Ohms 700W MONO
RMS Power at @ 1.3 Ohms 1200W MONO
crossover low pass filter Adjustable from 20Hz to 250Hz with a slope of 24dB per octave.This Maximum Power Output 4000W MONO
allows for the adjustment of the upper point of the frequency bandwidth
and the respective subwoofer. frequency response 20 Hz-250 Hz (-3dB)
high pass subsonic filter Adjustable from 15Hz to 40Hz with a slope of 24dB per octave.This allows input impedance 10K Ohms
for the attenuation of frequencies that are mostly inaudible and cause
unnecessary strain on the amplifier. input sensitivity 250mV~4V Adjustable
18
protection circuitry Protection against thermal, overload and short circuit conditions.
power supply voltage 14.4V DC Neg. Ground (10.5-16V)
remote dash-mount gain control This amplifier come complete with a compact remote GAIN CONTROLLER
which can be conveniently mounted on or under the dashboard of your min speaker lmpedance 1 Ohm
car.
T.H.D 0.1%
S/N ration >90dB
fuse 40A x 2
dimensions (W x H x L)
mm 281 x 59 x 381
inches 11.06 x 2.32 x 15
electrical connections
2 ch amp PLA-219 • PLA-2150 • PLA-2250 • PLA-2350
PLA-2450 • PLA-2550 • PLA-2650 • PLA-2750
PLA-2850 • PLA-4300D
PLA-219
PLA-2150
PLA-2250
PLA-2350
PLA-2450 19
PLA-2550
PLA-2650
PLA-2750 12V battery
PLA-4300D
to remote turn-on
+12V
electrical connections
4 ch amp PLA-419 • PLA-4150
PLA-4250 • PLA-4350
PLA-419
PLA-4150
PLA-4250
PLA-4350
20
12V battery
head unit
to remote turn-on
+12V
stereo input connections
2 ch amp PLA-219
PLA-2 1 9
L/R Audio
head unit
21
Outputs
L L R R
wiring harness
PLA-2 1 5 0
PLA-2250
PLA-2350
PLA-2450 head unit
head unit
L L R R
PLA-2 1 5 0
PLA-2250
PLA-2350
head unit
PLA-2450
PLA-2550 To a second amplifier
23
PLA-2650 Y Adaptors
head unit
To a second amplifier
L L R R
wiring harness wiring harness
PLA-4 1 9
L/R REAR
Audio Outputs
24
Audio Outputs
Y adaptors R
high level input connections
4 ch amp PLA-419
PLA-4 1 9
25
4 CH harness wiring for common ground connections
CH 3/4 CH 1/2
REAR L R L R FRONT
ORANGE ORANGE
BLACK BLACK REAR L R L R FRONT
BLACK BLACK
ORANGE ORANGE ORANGE ORANGE
from speaker terminals BLACK BLACK
PLEASE NOTE! If using high level inputs, BLACK BLACK
do not use the low level RCA inputs at ORANGE ORANGE
the same time!
from speaker terminals
Stereo input connections
4 ch amp PLA-4150 • PLA-4250 • PLA-4350
L/R FRONT
Audio Outputs
head unit
26
L/R REAR
Audio Outputs
Y adaptors L
high level Stereo input connections
4 ch amp PLA-4150 • PLA-4250 • PLA-4350
PLA-4 1 5 0
PLA-4250
PLA-4350
27
4 CH harness wiring for common ground connections
CH 3/4 CH 1/2
REAR L R L R FRONT
ORANGE ORANGE
BLACK BLACK REAR L R L R FRONT
BLACK BLACK
ORANGE ORANGE ORANGE ORANGE
from speaker terminals BLACK BLACK
PLEASE NOTE! If using high level inputs, BLACK BLACK
do not use the low level RCA inputs at ORANGE ORANGE
the same time!
from speaker terminals
mono input connections
4 ch amp PLA-4150 • PLA-4250 • PLA-4350
4 CH mono input connections using low level inputs
PLA-4 1 5 0
PLA-4250
PLA-4350
head unit
Y adaptors R
high level mono input connections
4 ch amp PLA-4150 • PLA-4250 • PLA-4350
4 CH floating ground connections
PLA-4150
PLA-4250
4 CH harness wiring
PLA-4350 for common ground connections
CH 3/4
29
CH 1/2
R L
ORANGE ORANGE
BLACK BLACK
R L
BLACK BLACK
ORANGE ORANGE
from speaker terminals ORANGE ORANGE
PLEASE NOTE! If using high level inputs, BLACK BLACK
do not use the low level RCA inputs at BLACK BLACK
the same time! ORANGE ORANGE
from speaker terminals
system wiring
Class-D MONO BLOCK AMPLIFIER PLA-4300D
PLA-4300D
M IN IM U M
SPEAKER
IM P E D A N CE
subwoofer 2~ 4 O H M S !
speaker connections
2 ch amp PLA-219 • PLA-2150 • PLA-2250 • PLA-2350
PLA-2450 • PLA-2550 • PLA-2650 • PLA-2750
PLA-2850
Stereo Output Mode
PLA-219
PLA-2150
PLA-2250
PLA-2350
PLA-2450 31
PLA-2550 Bridged Mono Output Mode (PLA-219 WITHOUT)
PLA-2650
PLA-2750
LEFT speaker RIGHT speaker
PLA-2850
MINIMUM
SPEAKER
IMPEDANCE
4 OHMS!
speaker
speaker connections
4 ch amp PLA-419 • PLA-4150
PLA-4250 • PLA-4350
4 CH Output Mode
PLA-4 1 9
PLA-4150
PLA-4250
PLA-4350
32
L R
FRONT speakers R L REAR speakers
MINIMUM
SPEAKER
IMPEDANCE
4 OHMS!
speakers
L R
speaker connections
4 ch amp PLA-4150 • PLA-4250 • PLA-4350
pb-836GX
PLA-4150
pb-1036GX
PLA-4250 2 CH Bridged Output Mode with Subwoofer Output
PLA-4350
33
MINIMUM
SPEAKER
R IMPEDANCE
L 4 OHMS!
SPEAKERS
SUBWOOFER
mounting and installation
mounting
Your new Pyle GearX Series amplifier comes complete with all required mounting hardware. When determining a suitable location in your vehicle for the amp, please remember
that it is a high-power electronic device capable of generating high heat.
For this reason, always choose a location in your vehicle which has low vibration, adequate ventilation, a minimum of dust, and no moisture. Be sure to
mount the amp in such a manner as to allow reasonable airflow over the cooling fins.
Mark the location for the mounting screw holes by positioning the amp where you wish to install it and use a scribe (or one of the mounting screws) inserted in each
of the mounting holes to mark the mounting surface. If the mounting surface is carpeted, measure the hole centers and mark with a felt tip pen.
Before attempting to drill the mounting holes, take note of any wires, lines or other devices in your vehicle which may be located behind the mounting
surface! Then drill pilot holes in the mounting surface for the mounting screws and insert them. Tighten the screws securely.
wiring tips 34
When making electrical connections to your amplifier, please observe the
following:
Wire the Remote connection to the auto start lead of your head unit, equalizer or power antenna.
fuses
About power fuses:
Pyle GearX Series amplifiers feature built-in fuse systems. These fuses protect both the amplifier
and the electrical system in your vehicle from fault conditions. If you ever need to replace the
fuse in your Pyle GearX Series amp, use a fuse of exactly the same type and rating. A different
type or rating of fuse may result in damage or fire.
troubleshooting
No output.
protection Confirm that all terminal strip connections are secure and tight.
circuitry Check both in-line and built-in fuses. Both the +12V and the Remote terminals must have +12v referenced to chassis
ground.
The built-in protection circuitry in the Pyle GearX Confirm that the audio signal source (car radio, equalizer, etc.) is connected and is supplying output signal. To
Series amplifiers will disable the amplifier if it senses check if the amp is supplying signal, unplug the cables from the signal source (but leave them plugged into the
an input overload, a speaker short circuit, or extreme amp). Briefly tap the center pin of each of the disconnected RCA plugs with your finger. This should produce a noise
temperature conditions. (feedback) in your speakers.
If the above steps fail to improve or clear noise interference, the system should be checked by a professional mobile
audio installer.
precautions notes
Do not operate the amplifier when it is unmounted.
Attach all audio system components securely within
the automobile to prevent damage, especially in an
accident.