Professional Documents
Culture Documents
Diy Plans EAW KF750
Diy Plans EAW KF750
TR-0750 Truss
Instructions for EAW KF750 Loudspeaker Truss
This TR-0750 suspension truss supports the Eastern Acoustic Works KF700 series touring speakers only. Do not use for
any other purpose.
Important:
Rigging loudspeakers requires experienced, trained professionals. Improperly
installed loudspeakers can result in property damage, personal injury,
death and/or liability to the installing contractor.
Read these important instructions for the best rigging results. Do not
exceed the working load limit of 1520 lbs./690 Kg. Use only Grade 8
supplied hardware. This truss supports a maximum of 7 (seven)
KF750 speakers in a vertical column.
Figure 1
Step 1.
Attach the hoist ring to the center hole of the hoist bracket using a 3/4” nut and
a 3/4” washer (Figure 1). Torque the nut down to 100 foot pounds.
Step 2.
Lay the TR-0750 truss on a flat surface making sure the arrows of the “ This
End Up” labels point up.
Step 3.
Mounting position of the Hoist Ring Assembly on the truss module will be
determined by the center of gravity of the array. Figure 2
Figure 3 Figure 4
Single cabinet Application Two Cabinet Application
Repeat procedure to the three right speakers (Figure 7). Be sure that all hardware, fasteners, cables and lifting chains are
fitted and secured before hoisting the truss/speaker array assembly.
When hoisting, lift entire system a short distance and check each and every connection thoroughly before proceeding.
2000 APC Incorporated, Signal Hill, CA 90806 USA (562) 424-1100
040301
Important:
Rigging loudspeakers requires experienced, trained professionals.
Improperly installed loudspeakers can result in property
damage, personal injury, death and/or liability to the
installing contractor.
As a guide, the installation, when completed, should be capable of supporting between ten times the actual combined
applied load.
Read these important instructions for the best rigging results. Do not exceed the working load limit of 1025
lbs./466 Kg. Use only Grade 8 hardware. This truss supports a maximum of 5 KF750 speakers in a vertical
column.
Make sure that all of the following items are included before proceeding:
1 pc. TR-0750-LT truss
1 pc. Hardware Kit
Box contents:
1 pc. “U-Hanger” assembly 2 pcs. ½” Split lock washer,grd 8
1 pc. Hoist ring, 2500 lbs WLL 8 pcs. ½” Flat washer, grd 8
1 pc. ¾-10 Hex nut, grd 8 2 pcs. ½-13 Nylock hex nut, grd 8
5 pcs. ¾” Flat washer, grd 8 2 pcs. ½-13 x 5.5” Hex bolt, grd 8
2 pcs. ¾”-10 x 2.5” Hex bolt, grd 8 4 pcs. ½-13 Eyebolt
2 pcs. ¾”-10 Nylock hex nut, grd 8 Figure 1
Step 2.
Place the TR-0750-LT truss on a flat surface making sure the arrows of the “ This End Up”
labels and the four threaded holes face upward.
Step 3.
Attach four 1/2-13 eyebolts and 1/2” washers to the four threaded holes of the truss (Figure
1). Tighten the eyebolts permanently.
Figure 2
2001 APC Incorporated, Signal Hill, CA 90806 USA (562) 424-1100 03/01/01
Single Cabinet application
Attach one end using suitable rigging gear such as aircraft cables, lifting chain or span sets to each eyebolt using a rated
shackle or other suitable rigging fasteners. Loop the unattached end of the rigging gear over the overhead rigging truss or
beam and attached back to the eyebolt. Repeat for other three eyebolt (Figure 3).
Lift the entire system a short distance and check all hardware, fasteners, and lifting gear in the system to
be sure they are fitted, aimed and secured thoroughly before proceeding.
Lift the entire system a short distance and check all hardware,
fasteners, and lifting gear in the system to be sure they are
fitted, aimed and secured thoroughly before proceeding.