Professional Documents
Culture Documents
Technical Information
Proline Promass F 200
Coriolis flowmeter
Table of contents
2 Endress+Hauser
Proline Promass F 200
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Standard documentation . . . . . . . . . . . . . . . . . . . . . . . . 84
Supplementary device-dependent documentation . . . . . . . 85
Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 85
Endress+Hauser 3
Proline Promass F 200
Document information
Symbols used Electrical symbols
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information.
Reference to documentation
Reference to page
Reference to graphic
Visual inspection
Symbols in graphics
4 Endress+Hauser
Proline Promass F 200
Fc = 2 · ∆m (ν · ω)
Fc = Coriolis force
∆m = moving mass
ω = rotational velocity
The amplitude of the Coriolis force depends on the moving mass ∆m, its velocity ν in the system and
thus on the mass flow. Instead of a constant rotational velocity ω, the sensor uses oscillation.
In the sensor, two parallel measuring tubes containing flowing fluid oscillate in antiphase, acting like
a tuning fork. The Coriolis forces produced at the measuring tubes cause a phase shift in the tube
oscillations (see illustration):
• At zero flow (when the fluid is at a standstill) the two tubes oscillate in phase (1).
• Mass flow causes deceleration of the oscillation at the inlet of the tubes (2) and acceleration at the
outlet (3).
1 2 3
A0016771
The phase difference (A-B) increases with increasing mass flow. Electrodynamic sensors register the
tube oscillations at the inlet and outlet. System balance is ensured by the antiphase oscillation of the
two measuring tubes. The measuring principle operates independently of temperature, pressure,
viscosity, conductivity and flow profile.
Density measurement
The measuring tube is continuously excited at its resonance frequency. A change in the mass and
thus the density of the oscillating system (comprising measuring tube and fluid) results in a
corresponding, automatic adjustment in the oscillation frequency. Resonance frequency is thus a
function of medium density. The microprocessor utilizes this relationship to obtain a density signal.
Volume measurement
Together with the measured mass flow, this is used to calculate the volume flow.
Temperature measurement
The temperature of the measuring tube is determined in order to calculate the compensation factor
due to temperature effects. This signal corresponds to the process temperature and is also available
as an output signal.
Endress+Hauser 5
Proline Promass F 200
Transmitter
Sensor
Safety IT security
We only provide a warranty if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any inadvertent
changes to the device settings.
IT security measures in line with operators' security standards and designed to provide additional
protection for the device and device data transfer must be implemented by the operators themselves.
Input
Measured variable Direct measured variables
• Mass flow
• Density
• Temperature
15 ½ 0 to 6 500 0 to 238.9
25 1 0 to 18 000 0 to 661.5
40 1½ 0 to 45 000 0 to 1 654
6 Endress+Hauser
Proline Promass F 200
50 2 0 to 70 000 0 to 2 573
DN x
8 ³⁄₈ 60
15 ½ 80
25 1 90
40 1½ 90
50 2 90
80 3 110
Endress+Hauser 7
Proline Promass F 200
HART protocol
The measured values are written from the automation system to the measuring device via the HART
protocol. The pressure transmitter must support the following protocol-specific functions:
• HART protocol
• Burst mode
Fieldbuses
The measured values can be written from the automation system to the measuring via:
• FOUNDATION Fieldbus
• PROFIBUS PA
Output
Output signal Current output
Resolution < 1 µA
Pulse/frequency/switch output
Pulse output
Frequency output
8 Endress+Hauser
Proline Promass F 200
Switch output
FOUNDATION Fieldbus
PROFIBUS PA
Current output
4-20 mA
Failure mode Selectable (as per NAMUR recommendation NE 43):
• Minimum value: 3.6 mA
• Maximum value: 22 mA
• Defined value: 3.59 to 22.5 mA
• Actual value
• Last valid value
HART
Device diagnostics Device condition can be read out via HART Command 48
Endress+Hauser 9
Proline Promass F 200
Pulse/frequency/switch output
Pulse output
Failure mode Choose from:
• Actual value
• No pulses
Frequency output
Failure mode Choose from:
• Actual value
• 0 Hz
• Defined value: 0 to 1 250 Hz
Switch output
Failure mode Choose from:
• Current status
• Open
• Closed
FOUNDATION Fieldbus
PROFIBUS PA
Local display
Backlight Additionally for device version with SD03 local display: red lighting indicates a
device error.
Operating tool
• Via digital communication:
– HART protocol
– FOUNDATION Fieldbus
– PROFIBUS PA
• Via service interface
10 Endress+Hauser
Proline Promass F 200
Load Load for current output: 0 to 500 Ω, depending on the external supply voltage of the power supply
unit
500
400
300
200
100
0
14 16 18 20 22 24 26 28 30 32 34 36 Us [V]
A0013563
1 Operating range
1.1 For order code for "Output", option A "4-20 mA HART"/option B "4-20 mA HART, pulse/frequency/switch
output" with Ex i and option C "4-20 mA HART + 4-20 mA analog"
1.2 For order code for "Output", option A "4-20 mA HART"/option B "4-20 mA HART, pulse/frequency/switch
output" with non-Ex and Ex d
Sample calculation
Supply voltage of the power supply unit: US = 19 V
Maximum load: RB ≤ (19 V - 13 V): 0.022 A = 273 Ω
Type of protection Ex d
Endress+Hauser 11
Proline Promass F 200
Ex nA type of protection
Type of protection XP
12 Endress+Hauser
Proline Promass F 200
Type of protection Ex ia
Pulse/frequency/switch output Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 6 nF
Pulse/frequency/switch output Ui = 30 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Pulse/frequency/switch output Ui = 30 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Endress+Hauser 13
Proline Promass F 200
Type of protection Ex ic
Pulse/frequency/switch output Ui = DC 35 V
Ii = n.a.
Pi = 1 W
Li = 0 μH
Ci = 6 nF
Pulse/frequency/switch output Ui = 35 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Pulse/frequency/switch output Ui = 35 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Type of protection IS
14 Endress+Hauser
Proline Promass F 200
Pulse/frequency/switch output Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 6 nF
Pulse/frequency/switch output Ui = 30 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Pulse/frequency/switch output Ui = 30 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Low flow cut off The switch points for low flow cut off are user-selectable.
Galvanic isolation All outputs are galvanically isolated from one another.
Manufacturer ID 0x11
Endress+Hauser 15
Proline Promass F 200
FOUNDATION Fieldbus
Manufacturer ID 0x452B48
Device revision 1
Number of VCRs 44
Permanent entries 1
16 Endress+Hauser
Proline Promass F 200
Client VCRs 0
Server VCRs 10
Source VCRs 43
Sink VCRs 0
Subscriber VCRs 43
Publisher VCRs 43
Slot time 4
Transducer Blocks
Setup Transducer Block All parameters for standard commissioning. No output values
(TRDSUP)
Advanced Setup All parameters for more accurate measurement No output values
Transducer Block configuration.
(TRDASUP)
Display Transducer Parameters for configuring the local display. No output values
Block
(TRDDISP)
HistoROM Transducer Parameters for using the HistoROM function. No output values
Block
(TRDHROM)
Expert Configuration Parameters that require the user to have in- No output values
Transducer Block depth knowledge of the operation of the device
(TRDEXP) in order to configure the parameters
appropriately.
Expert Information Parameters that provide information about the No output values
Transducer Block state of the device.
(TRDEXPIN)
Service Sensor Parameters that can only be accessed by Endress No output values
Transducer Block +Hauser Service.
(TRDSRVS)
Total Inventory Parameters for configuring all the totalizers and Process variables (AI Channel)
Counter Transducer the inventory counter. • Totalizer 1 (16)
Block • Totalizer 2 (17)
(TRDTIC) • Totalizer 3 (18)
Heartbeat Results 1 Information about the results of the verification. No output values
Transducer Block
(TRDHBTR1)
Endress+Hauser 17
Proline Promass F 200
Heartbeat Results 2 Information about the results of the verification. No output values
Transducer Block
(TRDHBTR2)
Heartbeat Results 3 Information about the results of the verification. No output values
Transducer Block
(TRDHBTR3)
Heartbeat Results 4 Information about the results of the verification. No output values
Transducer Block
(TRDHBTR4)
Function blocks
Discrete Input 2 This Block (standard functionality) receives a • Switch output state (101)
Block discrete value (e.g. indicator that measuring • Empty pipe detection (102)
(DI) range has been exceeded) and makes the • Low flow cut off (103)
value available for other blocks at the output. • Status verification (105)
Execution time: 19 ms
18 Endress+Hauser
Proline Promass F 200
PROFIBUS PA
Manufacturer ID 0x11
Endress+Hauser 19
Proline Promass F 200
Power supply
Terminal assignment Transmitter
Connection versions
2 1 3 2 1 3
+ – + –
3 4 1 2 + – +–
3 4 1 2
A0013570 A0018161
Maximum number of terminals, without integrated Maximum number of terminals, with integrated
overvoltage protection overvoltage protection
Output 1 Output 2
20 Endress+Hauser
Proline Promass F 200
Output 1 Output 2
Pulse/frequency/switch output
Option E 1) 2) FOUNDATION Fieldbus
(passive)
Pulse/frequency/switch output
Option G 1) 3) PROFIBUS PA
(passive)
1 4 2 Grounding
3 - PROFIBUS PA –
A0019021
4 Not assigned
FOUNDATION Fieldbus
1 4 2 - Signal –
3 Not assigned
A0019021
4 Grounding
Minimum Maximum
Order code for "Output"
terminal voltage terminal voltage
Option A 1) 2)
: 4-20 mA HART • For 4 mA: ≥ DC 17.9 V
DC 35 V
• For 20 mA: ≥ DC 13.5 V
Option C 1) 2)
: 4-20 mA HART + 4-20 mA analog • For 4 mA: ≥ DC 17.9 V
DC 30 V
• For 20 mA: ≥ DC 13.5 V
Endress+Hauser 21
Proline Promass F 200
Minimum Maximum
Order code for "Output"
terminal voltage terminal voltage
Various power supply units can be ordered from Endress+Hauser: see "Accessories" section
→ 84
For information on the Ex connection values → 11
PROFIBUS PA
16 mA
FOUNDATION Fieldbus
18 mA
22 Endress+Hauser
Proline Promass F 200
A0015510
Connection examples
1 2 3 4
4...20 mA
+ +
5
- -
A0015511
Pulse/frequency output
1 2
– +
_ +
– 3
+
12345
A0016801
Endress+Hauser 23
Proline Promass F 200
Switch output
1 2
_ +
_
+
_ 3
+
A0016802
PROFIBUS-PA
1 2 3 4
+ +
- - 5
6
6 6
+ 5
-
6
6
8 . - 7
A0019004
24 Endress+Hauser
Proline Promass F 200
FOUNDATION Fieldbus
1 2 3 4
+ +
- - 5
6
6 6
+ 5
-
6
6
8 . - 7
A0019004
HART input
1 2 3 4 5
4...20 mA
+ +
+
– – 7
+ -
–
–
+
+ +
+
– – 6
-
3 4
A0016029
Endress+Hauser 25
Proline Promass F 200
Terminals • For device version without integrated overvoltage protection: plug-in spring terminals for wire
cross-sections 0.5 to 2.5 mm2 (20 to 14 AWG)
• For device version with integrated overvoltage protection: screw terminals for wire cross-sections
0.2 to 2.5 mm2 (24 to 14 AWG)
Cable entries • Cable gland (not for Ex d): M20 × 1.5 with cable 6 to 12 mm (0.24 to 0.47 in)
• Thread for cable entry:
– For non-Ex and Ex: NPT ½"
– For non-Ex and Ex (not for CSA Ex d/XP): G ½"
– For Ex d: M20 × 1.5
Signal cable
Current output
• For 4-20 mA: standard installation cable is sufficient.
• For 4-20 mA HART: Shielded cable recommended. Observe grounding concept of the plant.
Pulse/frequency/switch output
Standard installation cable is sufficient.
FOUNDATION Fieldbus
Twisted, shielded two-wire cable.
For further information on planning and installing FOUNDATION Fieldbus networks see:
• Operating Instructions for "FOUNDATION Fieldbus Overview" (BA00013S)
• FOUNDATION Fieldbus Guideline
• IEC 61158-2 (MBP)
PROFIBUS PA
Twisted, shielded two-wire cable. Cable type A is recommended.
For further information on planning and installing PROFIBUS PA networks see:
• Operating Instructions "PROFIBUS DP/PA: Guidelines for planning and commissioning"
(BA00034S)
• PNO Directive 2.092 "PROFIBUS PA User and Installation Guideline"
• IEC 61158-2 (MBP)
Overvoltage protection The device can be ordered with integrated overvoltage protection for diverse approvals:
Order code for "Accessory mounted", option NA "Overvoltage protection"
1)
Input voltage range Values correspond to supply voltage specifications
26 Endress+Hauser
Proline Promass F 200
Depending on the temperature class, restrictions apply to the ambient temperature for device
versions with overvoltage protection
Performance characteristics
Reference operating • Error limits based on ISO 11631
conditions • Water with +15 to +45 °C (+59 to +113 °F) at 2 to 6 bar (29 to 87 psi)
• Specifications as per calibration protocol
• Accuracy based on accredited calibration rigs that are traced to ISO 17025.
To obtain measured errors, use the Applicator sizing tool → 83
Base accuracy
Mass flow and volume flow (liquids)
±0.10 % o.r.
Mass flow (gases)
±0.35 % o.r.
Design fundamentals
Density (liquids)
• Reference conditions: ±0.0005 g/cm³
• Standard density calibration: ±0.01 g/cm³
(valid over the entire temperature range and density range )
• Wide-range density specification (order code for "Application package", option EF "Special density
and concentration ") : ±0.001 g/cm³ (valid range for special density calibration: 0 to 2 g/cm³,
+5 to +80 °C (+41 to +176 °F))
Temperature
±0.5 °C ± 0.005 · T °C (±0.9 °F ± 0.003 · (T – 32) °F)
15 ½ 0.585 0.021
25 1 1.62 0.059
40 1½ 4.05 0.149
50 2 6.30 0.231
80 3 16.2 0.617
Flow values
Flow values as turndown parameter depending on nominal diameter.
Endress+Hauser 27
Proline Promass F 200
SI units
US units
Accuracy of outputs
o.r. = of reading
The outputs have the following base accuracy specifications.
Current output
Accuracy ±10 µA
Pulse/frequency output
Base repeatability
Mass flow and volume flow (liquids)
±0.05 % o.r.
Mass flow (gases)
±0.25 % o.r.
Design fundamentals
Density (liquids)
±0.00025 g/cm3
Temperature
±0.25 °C ± 0.0025 · T °C (±0.45 °F ± 0.0015 · (T–32) °F)
28 Endress+Hauser
Proline Promass F 200
Pulse/frequency output
[kg/m3]
10
8 1
6
4 2
2
0
-50 0 50 100 150 200 [°C]
-80 -40 0 40 80 120 160 200 240 280 320 360 400 [°F]
A0016591
Temperature
±0.005 · T °C (± 0.005 · (T – 32) °F)
Influence of medium The table below shows the effect on accuracy of mass flow due to a difference between calibration
pressure pressure and process pressure.
o.r. = of reading
DN [% o.r./bar] [% o.r./psi]
[mm] [in]
8 3/8 no influence
15 ½ no influence
25 1 no influence
Endress+Hauser 29
Proline Promass F 200
DN [% o.r./bar] [% o.r./psi]
[mm] [in]
40 1½ –0.003 –0.0002
50 2 –0.008 –0.0006
80 3 –0.009 –0.0006
ZeroPoint
³ BaseAccu ⋅ 100 ± BaseAccu
A0021339
A0021332
ZeroPoint ZeroPoint
< BaseAccu ⋅ 100 MeasValue ⋅ 100
±
A0021333 A0021334
4
⁄3 ⋅ ZeroPoint ZeroPoint
⋅ 100 MeasValue ⋅ 100
< ± 2 ⁄3 ⋅
BaseAccu
A0021342 A0021344
E [%]
2.5
2.0
1.5
1.0
0.5
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Q [%]
A0018211
Design fundamentals
Installation
No special measures such as supports are necessary. External forces are absorbed by the construction
of the device.
30 Endress+Hauser
Proline Promass F 200
Mounting location To prevent measuring errors arising from accumulation of gas bubbles in the measuring tube, avoid
the following mounting locations in the pipe:
• Highest point of a pipeline.
• Directly upstream of a free pipe outlet in a down pipe.
A0023344
A0015596
8 ³⁄₈ 6 0.24
15 ½ 10 0.40
25 1 14 0.55
40 1½ 22 0.87
50 2 28 1.10
80 3 50 1.97
Orientation The direction of the arrow on the sensor nameplate helps you to install the sensor according to the
flow direction (direction of medium flow through the piping).
Endress+Hauser 31
Proline Promass F 200
Orientation Recommendation
A Vertical orientation
A0015591
1)
B Horizontal orientation, transmitter
head up Exception:→ 8,
32
A0015589
2)
C Horizontal orientation, transmitter
head down Exception:
→ 8, 32
A0015590
1) Applications with low process temperatures may reduce the ambient temperature. To maintain the
minimum ambient temperature for the transmitter, this orientation is recommended.
2) Applications with high process temperatures may increase the ambient temperature. To maintain the
maximum ambient temperature for the transmitter, this orientation is recommended.
If a sensor is installed horizontally with a curved measuring tube, match the position of the sensor to
the fluid properties.
1 2
A0014057
Inlet and outlet runs No special precautions need to be taken for fittings which create turbulence, such as valves, elbows
or T-pieces, as long as no cavitation occurs → 46.
32 Endress+Hauser
Proline Promass F 200
E 45°
D
i
C
1 3
B
RUPTURE DISK
2
A0008361
DN A B C D E
[mm] [in] [mm] [in] [in] [in] [mm] [in] [mm] [in]
Environment
Ambient temperature range Measuring device • –40 to +60 °C (–40 to +140 °F)
• –50 to +60 °C (–58 to +140 °F) (order code for "Test, certificate", option JN)
‣ If operating outdoors:
Avoid direct sunlight, particularly in warm climatic regions.
Weather protection covers can be ordered from Endress+Hauser: see "Accessories" section
→ 82
Endress+Hauser 33
Proline Promass F 200
Temperature tables
In the following tables, the following interdependencies between the maximum medium
temperature Tm for T6 to T1 and the maximum ambient temperature Ta apply when operating the
device in hazardous areas.
Order code for "Output", option A "4-20mA HART"
• Ex ia, Ex ic, Ex nA, Ex d
• CCSAUS IS, CCSAUS XP, CCSAUS NI
SI units
Ta T6 T5 T4 T3 T2 T1
[°C] [85 °C] [100 °C] [135 °C] [200 °C] [300 °C] [450 °C]
1) The following applies for installations with overvoltage protection in conjunction with temperature class
T5, T6 and approval codes IB, ID, IH, IJ, I4, BB, BD, BH, BJ, B2, C2, C5: Ta = Ta - 2 °C
2) The following applies for sensors with a nominal diameter DN 80: Tm = 85 °C
3) The following applies for sensors with a nominal diameter DN 80: Tm = 110 °C
4) The following applies for specified sensors with a maximum medium temperature Tm = 205 °C: Tm = 170 °C
5) The following applies for specified sensors with a maximum medium temperature Tm = 205 °C: Tm = 205 °C
US units
Ta T6 T5 T4 T3 T2 T1
[°F] [185 °F] [212 °F] [275 °F] [392 °F] [572 °F] [842 °F]
1) The following applies for installations with overvoltage protection in conjunction with temperature class
T5, T6 and approval codes IB, ID, IH, IJ, I4, BB, BD, BH, BJ, B2, C2, C5: Ta = Ta - 3.6 °F
2) The following applies for sensors with a nominal diameter DN 3": Tm = 185 °F
3) The following applies for sensors with a nominal diameter DN 3": Tm = 230 °F
4) The following applies for specified sensors with a maximum medium temperature Tm = 401 °F: Tm = 338 °F
5) The following applies for specified sensors with a maximum medium temperature Tm = 401 °F: Tm = 401 °F
SI units
Ta T6 T5 T4 T3 T2 T1
[°C] [85 °C] [100 °C] [135 °C] [200 °C] [300 °C] [450 °C]
34 Endress+Hauser
Proline Promass F 200
US units
Ta T6 T5 T4 T3 T2 T1
[°F] [185 °F] [212 °F] [275 °F] [392 °F] [572 °F] [842 °F]
SI units
Ta T6 T5 T4 T3 T2 T1
[°C] [85 °C] [100 °C] [135 °C] [200 °C] [300 °C] [450 °C]
US units
Ta T6 T5 T4 T3 T2 T1
[°F] [185 °F] [212 °F] [275 °F] [392 °F] [572 °F] [842 °F]
1) The following applies for sensors with a nominal diameter DN 3": Tm = 185 °F
2) The following applies for sensors with a nominal diameter DN 3": Tm = 230 °F
3) The following applies for specified sensors with a maximum medium temperature Tm = 401 °F: Tm = 338 °F
4) The following applies for specified sensors with a maximum medium temperature Tm = 401 °F: Tm = 401 °F
5) Ta = 131 °F for pulse/frequency/switch output Pi ≤ 0.85 W
Endress+Hauser 35
Proline Promass F 200
SI units
Ta T6 T5 T4 T3 T2 T1
[°C] [85 °C] [100 °C] [135 °C] [200 °C] [300 °C] [450 °C]
1) The following applies for installations with overvoltage protection in conjunction with temperature class
T5, T6: Ta = Ta - 2 °C
2) The following applies for sensors with a nominal diameter DN 80: Tm = 85 °C
3) The following applies for sensors with a nominal diameter DN 80: Tm = 110 °C
4) The following applies for specified sensors with a maximum medium temperature Tm = 205 °C: Tm = 170 °C
5) The following applies for specified sensors with a maximum medium temperature Tm = 205 °C: Tm = 205 °C
US units
Ta T6 T5 T4 T3 T2 T1
[°F] [185 °F] [212 °F] [275 °F] [392 °F] [572 °F] [842 °F]
1) The following applies for installations with overvoltage protection in conjunction with temperature class
T5, T6: Ta = Ta - 3.6 °F
2) The following applies for sensors with a nominal diameter DN 3": Tm = 185 °F
3) The following applies for sensors with a nominal diameter DN 3": Tm = 230 °F
4) The following applies for specified sensors with a maximum medium temperature Tm = 401 °F: Tm = 338 °F
5) The following applies for specified sensors with a maximum medium temperature Tm = 401 °F: Tm = 401 °F
SI units
Ta T6 T5 T4 T3 T2 T1
[°C] [85 °C] [100 °C] [135 °C] [200 °C] [300 °C] [450 °C]
1) The following applies for installations with overvoltage protection in conjunction with temperature class
T5, T6 and approval codes ID, IG, IH, BD, BH, C4, C7: Ta = Ta - 2 °C
2) The following applies for sensors with a nominal diameter DN 80: Tm = 85 °C
3) The following applies for sensors with a nominal diameter DN 80: Tm = 110 °C
4) The following applies for specified sensors with a maximum medium temperature Tm = 205 °C: Tm = 170 °C
5) The following applies for specified sensors with a maximum medium temperature Tm = 205 °C: Tm = 205 °C
36 Endress+Hauser
Proline Promass F 200
US units
Ta T6 T5 T4 T3 T2 T1
[°F] [185 °F] [212 °F] [275 °F] [392 °F] [572 °F] [842 °F]
1) The following applies for installations with overvoltage protection in conjunction with temperature class
T5, T6 and approval codes ID, IG, IH, BD, BH, C4, C7: Ta = Ta - 3.6 °F
2) The following applies for sensors with a nominal diameter DN 3": Tm = 185 °F
3) The following applies for sensors with a nominal diameter DN 3": Tm = 230 °F
4) The following applies for specified sensors with a maximum medium temperature Tm = 401 °F: Tm = 338 °F
5) The following applies for specified sensors with a maximum medium temperature Tm = 401 °F: Tm = 401 °F
Order code for "Output", option E "FOUNDATION Fieldbus, pulse/frequency/switch output" and
option G "PROFIBUS PA, pulse/frequency/switch output"
• Ex ia, Ex ic
• CCSAUS IS
SI units
Ta T6 T5 T4 T3 T2 T1
[°C] [85 °C] [100 °C] [135 °C] [200 °C] [300 °C] [450 °C]
US units
Ta T6 T5 T4 T3 T2 T1
[°F] [185 °F] [212 °F] [275 °F] [392 °F] [572 °F] [842 °F]
Order code for "Output", option E "FOUNDATION Fieldbus, pulse/frequency/switch output" and
option G "PROFIBUS PA, pulse/frequency/switch output"
• Ex d, Ex nA
• CCSAUS XP, CCSAUS NI
Endress+Hauser 37
Proline Promass F 200
SI units
Ta T6 T5 T4 T3 T2 T1
[°C] [85 °C] [100 °C] [135 °C] [200 °C] [300 °C] [450 °C]
US units
Ta T6 T5 T4 T3 T2 T1
[°F] [185 °F] [212 °F] [275 °F] [392 °F] [572 °F] [842 °F]
Example
• Measured maximum ambient temperature: Tma = 47 °C
• Measured maximum medium temperature: Tmm = 108 °C
Ta T6 T5 T4 T3 T2 T1
[°C] [85°C] [100°C] [135°C] [200°C] [300°C] [450°C]
35 50 85 120 140 140 140
50 – 85 120 140 140 140
60 – – 120 140 140 140
35 50 85 120 140 140 140
45 – 85 120 140 140 140
50 – – 120 140 140 140
A0019758
38 Endress+Hauser
Proline Promass F 200
2. In the column for the maximum ambient temperature Ta select the temperature that is
immediately greater than or equal to the measured maximum ambient temperature Tma that is
present.
Ta = 50 °C.
The row showing the maximum medium temperature is determined.
3. Select the maximum medium temperature Tm of this row, which is larger or equal to the
measured maximum medium temperature Tmm.
The column with the temperature class for gas is determined: 108 °C ≤ 120°C → T4.
4. The maximum temperature of the temperature class determined corresponds to the maximum
surface temperature for dust: T4 = 135 °C
Storage temperature –40 to +80 °C (–40 to +176 °F), preferably at +20 °C (+68 °F)
Process
Medium temperature range Sensor
• –50 to +150 °C (–58 to +302 °F)
• –50 to +205 °C (–58 to +401 °F) with extended temperature (order code for "Measuring tube mat.",
option SD, SE, SF, TH)
Endress+Hauser 39
Proline Promass F 200
Seals
No internal seals
Pressure-temperature The following pressure/temperature diagrams apply to all pressure-bearing parts of the device and
ratings not just the process connection.
[psi] [bar]
100
1400 PN 100
90
1200
80
1000 70
60 PN 63
800
50
600 40
PN 40
400 30
20
200
10 PN 16
0 0
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0029377-EN
40 Endress+Hauser
Proline Promass F 200
[psi] [bar]
100
1400 Class 600
90
1200
80
1000 70
60
800 Class 300
50
600 40
400 30
Class 150
20
200
10
0 0
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0029378-EN
[psi] [bar]
100 Class 600
1400
90
1200
80
1000 70
60
800 Class 300
50
600 40
400 30
Class 150
20
200
10
0 0
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0029379-EN
Endress+Hauser 41
Proline Promass F 200
[psi] [bar]
1000 70
60 63K
800
50
600 40
40K
400 30
20
200 20K
10
10K
0 0
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0029380-EN
[psi] [bar]
600 40
400 30 DN 8...40
20
200
10 ≥DN 50
0 0
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0027781-EN
[psi] [bar]
700 50
600 40
500 PN 40
400 30
300 20
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0027777-EN
42 Endress+Hauser
Proline Promass F 200
[psi] [bar]
100
1400 Class 600
90
1200
80
1000 70
60
800 Class 300
50
600 40
400 30
Class 150
20
200
10
0 0
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0029381-EN
[psi] [bar]
400 30
20
200 20K
10
0 0
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0029386-EN
[psi] [bar]
50
600 40
DN 8…40
400 30
20 ≥DN 50
200
10
0 0
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0027783-EN
DIN 11851 allows for applications up to +140 °C (+284 °F) if suitable sealing materials are used.
Please take this into account when selecting seals and counterparts, as these components can limit
the pressure and temperature range.
Endress+Hauser 43
Proline Promass F 200
[psi] [bar]
50
600 40
DN 8...40
400 30
20 ≥DN 50
200
10
0 0
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0027784-EN
[psi] [bar]
400 30
20
200
10
0 0
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0027785-EN
[psi] [bar]
8
100
6
50 2
0 0
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0027786-EN
SMS 1145 allows for applications up to 6 bar (87 psi) if suitable sealing materials are used. Please
take this into account when selecting seals and counterparts, as these components can limit the
pressure and temperature range.
44 Endress+Hauser
Proline Promass F 200
VCO
[psi] [bar]
100
1400
90
1200 80
1000 70
-50 0 50 100 150 200 [°C]
-50 0 50 100 150 200 250 300 350 400 [°F]
A0029395-EN
Tri-Clamp
The clamp connections are suitable up to a maximum pressure of 16 bar (232 psi). Please observe
the operating limits of the clamp and seal used as they can be over 16 bar (232 psi). The clamp and
seal are not included in the scope of supply.
Secondary containment The sensor housing is filled with dry nitrogen and protects the electronics and mechanics inside.
pressure rating
The following secondary containment pressure rating is only valid for a fully welded sensor housing
and/or a device equipped with closed purge connections (never opened/as delivered).
If there is a risk of the measuring tube breaking due to process characteristics, e.g. in the case of
corrosive fluids, we recommend the use of sensors whose secondary containment is equipped
with special "pressure monitoring connections" (order code for "Sensor option", option CH "rinse
connection").
With the help of these connections, the fluid collected in the secondary containment can be
bled off in the event of tube failure. This is especially important in high-pressure gas
applications. These connections can also be used for gas purging (gas detection).
Do not open the purge connections unless the containment can be filled immediately with a
dry, inert gas. Use only low gauge pressure to purge. Maximum pressure: 5 bar (72.5 psi).
If a device fitted with purge connections is connected to the purge system, the maximum
nominal pressure is determined by the purge system itself or by the device, depending on which
component has the lower nominal pressure.
If, on the other hand, the device is fitted with a rupture disk, the rupture disk is decisive for the
maximum nominal pressure → 45.
Dimensions: → 48
Rupture disk To increase the level of safety, a device version with a rupture disk with a trigger pressure of
10 to 15 bar (145 to 217.5 psi) can be used (order code for "Sensor option", option CA "rupture disk").
Rupture disks cannot be combined with the separately available heating jacket .
Endress+Hauser 45
Proline Promass F 200
Flow limit Select the nominal diameter by optimizing between the required flow range and permissible pressure
loss.
For an overview of the full scale values for the measuring range, see the "Measuring range"
section
• The minimum recommended full scale value is approx. 1/20 of the maximum full scale value
• In most applications, 20 to 50 % of the maximum full scale value can be considered ideal
• A low full scale value must be selected for abrasive media (such as liquids with entrained solids):
flow velocity < 1 m/s (< 3 ft/s).
• For gas measurement the following rules apply:
– The flow velocity in the measuring tubes should not exceed half the sound velocity (0.5 Mach).
– The maximum mass flow depends on the density of the gas: formula
Pressure loss To calculate the pressure loss, use the Applicator sizing tool → 83
Promass F with reduced pressure loss: order code for "Sensor option", option CE "reduced pressure
loss"
System pressure It is important that cavitation does not occur, or that gases entrained in the liquids do not outgas.
This is prevented by means of a sufficiently high system pressure.
For this reason, the following mounting locations are recommended:
• At the lowest point in a vertical pipe
• Downstream from pumps (no danger of vacuum)
A0015594
Thermal insulation In the case of some fluids, it is important that the heat radiated from the sensor to the transmitter is
kept to a minimum. A wide range of materials can be used for the required insulation.
NOTICE
Danger of overheating with insulation
‣ Ensure that the temperature at the lower end of the transmitter housing does not exceed
80 °C (176 °F)
NOTICE
The insulation can also be thicker than the maximum recommended insulation thickness.
Prerequisite:
‣ Ensure that convection takes place on a sufficiently large scale at the transmitter neck.
‣ Ensure that a sufficiently large area of the housing support remains exposed. The uncovered part
serves as a radiator and protects the electronics from overheating and excessive cooling.
A0019919
46 Endress+Hauser
Proline Promass F 200
The minimum distance between the transmitter housing and the insulation is 20 mm (0.79 in). This
is to ensure that the transmitter head remains completely exposed.
Heating Some fluids require suitable measures to avoid loss of heat at the sensor.
Heating options
• Electrical heating, e.g. with electric band heaters
• Via pipes carrying hot water or steam
• Via heating jackets
Heating jackets for the sensors can be ordered as accessories from Endress+Hauser → 81.
NOTICE
Danger of overheating when heating
‣ Ensure that the temperature at the lower end of the transmitter housing does not exceed
80 °C (176 °F).
‣ Ensure that convection takes place on a sufficiently large scale at the transmitter neck.
‣ Ensure that a sufficiently large area of the housing support remains exposed. The uncovered part
serves as a radiator and protects the electronics from overheating and excessive cooling.
Vibrations The high oscillation frequency of the measuring tubes ensures that the correct operation of the
measuring system is not influenced by plant vibrations.
Endress+Hauser 47
Proline Promass F 200
Mechanical construction
Dimensions in SI units Compact version
Order code for "Housing", option B "GT18 two-chamber, 316L"; C "GT20 two-chamber aluminum-
coated"
A D
B C E F
H
I
G
K
L
A0017733
DN A B 1) C D 2) E F 2) G H 3) I 3) K L
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
4)
8 162 102 60 165 75 90 5.35 268 343 75
4)
15 162 102 60 165 75 90 8.30 268 343 75
4)
25 162 102 60 165 75 90 12.0 268 343 75
4)
40 162 102 60 165 75 90 17.6 273 378 105
4)
50 162 102 60 165 75 90 26.0 283 424 141
4)
80 162 102 60 165 75 90 40.5 302 502 200
48 Endress+Hauser
Proline Promass F 200
Flange connections
C
A
B
E
D L
A0029370
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
Surface roughness (flange): EN 1092-1 Form B1 (DIN 2526 Form C), Ra 3.2 to 12.5 µm
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
Surface roughness (flange): EN 1092-1 Form B1 (DIN 2526 Form C), Ra 3.2 to 12.5 µm
Endress+Hauser 49
Proline Promass F 200
Surface roughness (flange): EN 1092-1 Form B1 (DIN 2526 Form C), Ra 3.2 to 12.5 µm
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
Surface roughness (flange): EN 1092-1 Form B2 (DIN 2526 Form E), Ra 0.8 to 3.2 µm
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
50 Endress+Hauser
Proline Promass F 200
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
Flange according to ASME B16.5: Class 150 with reduction in nominal diameter
1.4404 (F316/F316L)
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
Flange according to ASME B16.5: Class 300 with reduction in nominal diameter
1.4404 (F316/F316L)
Endress+Hauser 51
Proline Promass F 200
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
8 1) 95 70 4 × ⌀15 14 15 370
15 95 70 4 × ⌀15 14 15 404
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
52 Endress+Hauser
Proline Promass F 200
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
Endress+Hauser 53
Proline Promass F 200
X X
C
A
B
E
D
L
A0029371
23 Detail X: Asymmetrical process connection; the part shown in gray is provided by the supplier.
Flange DIN11864-2 Form A, for pipe according to DIN11866 series A, flat flange
1.4404 (316/316L)
Order code for "Process connection", option KCS
DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
8 54 37 4 × ⌀9 10 10 387
15 59 42 4 × ⌀9 10 16 418
25 70 53 4 × ⌀9 10 26 454
40 82 65 4 × ⌀9 10 38 560
50 94 77 4 × ⌀9 10 50 720
3A-version available: order code for "Additional approval", option LP in conjunction with
Ra ≤ 0.8 µm: order code for "Measuring tube material", option SB, SE or
Ra ≤ 0.4 µm: order code for "Measuring tube material", option SC, SF
54 Endress+Hauser
Proline Promass F 200
C
A
B
E
F
D L
A0029372
DN A B C D E F L Ldiff 1)
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
1) Difference to installation length of the welding neck flange (order code for "Process connection", option
D2C)
2) DN 8 with DN 15 flanges as standard
DN A B C D E F L Ldiff 1)
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
1) Difference to installation length of the welding neck flange (order code for "Process connection", option
AAC)
2) DN 8 with DN 15 flanges as standard
Endress+Hauser 55
Proline Promass F 200
DN A B C D E F L Ldiff 1)
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
1) Difference to installation length of the welding neck flange (order code for "Process connection", option
ABC)
2) DN 8 with DN 15 flanges as standard
DN A B C D E F L Ldiff 1)
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
1) Difference to installation length of the welding neck flange (order code for "Process connection", option
ACC)
2) DN 8 with DN 15 flanges as standard
DN A B C D E F L Ldiff 1)
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
8 2) 95 70 4 × ⌀ 15 14 51 15 370 0
15 95 70 4 × ⌀ 15 14 51 15 404 0
1) Difference to installation length of the welding neck flange (order code for "Process connection", option
NEC)
2) DN 8 with DN 15 flanges as standard
56 Endress+Hauser
Proline Promass F 200
Clamp connections
Tri-Clamp
B
L
A0029373
DN Clamp A B L
[mm] [in] [mm] [mm] [mm]
3A-version available: order code for "Additional approval", option LP in conjunction with
Ra ≤ 0.8 µm: order code for "Measuring tube material", option SB, SE or
Ra ≤ 0.4 µm: order code for "Measuring tube material", option SC, SF
DN Clamp A B L
[mm] [in] [mm] [mm] [mm]
3A-version available: order code for "Additional approval", option LP in conjunction with
Ra ≤ 0.8 µm: order code for "Measuring tube material", option SB, SE or
Ra ≤ 0.4 µm: order code for "Measuring tube material", option SC, SF
Endress+Hauser 57
Proline Promass F 200
Cable glands
A
B
L
A0029374
Threaded hygienic connection DIN 11851, for pipe according to DIN11866, series A
1.4404 (316/316L)
Order code for "Process connection", option FMW
DN A B L
[mm] [in] [mm] [mm]
8 Rd 34 × ¹⁄₈ 16 367
15 Rd 34 × ¹⁄₈ 16 398
25 Rd 52 × ¹⁄₆ 26 434
40 Rd 65 × ¹⁄₆ 38 560
50 Rd 78 × ¹⁄₆ 50 720
3A-version available: order code for "Additional approval", option LP in conjunction with
Ra ≤ 0.8 µm: order code for "Measuring tube material", option SB, SE
Threaded hygienic connection DIN11864-1 Form A, for pipe according to DIN11866, series A
1.4404 (316/316L)
Order code for "Process connection", option FLW
DN A B L
[mm] [in] [mm] [mm]
8 Rd 28 × ¹⁄₈ 10 367
15 Rd 34 × ¹⁄₈ 16 398
25 Rd 52 × ¹⁄₈ 26 434
40 Rd 65 × ¹⁄₆ 38 560
50 Rd 78 × ¹⁄₆ 50 720
3A-version available: order code for "Additional approval", option LP in conjunction with
Ra ≤ 0.8 µm: order code for "Measuring tube material", option SB, SE or
Ra ≤ 0.4 µm: order code for "Measuring tube material", option SC, SF
58 Endress+Hauser
Proline Promass F 200
DN A B L
[mm] [in] [mm] [mm]
3A-version available: order code for "Additional approval", option LP in conjunction with
Ra ≤ 0.8 µm: order code for "Measuring tube material", option SB, SE
Endress+Hauser 59
Proline Promass F 200
A
B
L
A0029375
Threaded hygienic connection ISO 2853, for pipe according to ISO 2037
1.4404 (316/316L)
Order code for "Process connection", option JSF
DN A 1) B L
[mm] [mm] [mm] [mm]
3A-version available: order code for "Additional approval", option LP in conjunction with
Ra ≤ 0.8 µm: order code for "Measuring tube material", option SB, SE or
Ra ≤ 0.4 µm: order code for "Measuring tube material", option SC, SF
60 Endress+Hauser
Proline Promass F 200
VCO
B
L
A0029376
8-VCO-4 (½")
1.4404 (316/316L)
Order code for "Process connection", option CVS
DN A B L
[mm] [in] [mm] [mm]
8 AF 1 10.2 390
12-VCO-4 (¾")
1.4404 (316/316L)
Order code for "Process connection", option CWS
DN A B L
[mm] [in] [mm] [mm]
15 AF 1½ 15.7 430
Endress+Hauser 61
Proline Promass F 200
Accessories
45° L
H
G
A0002537
DN G H L
8 ½ NPT 62 216
15 ½ NPT 62 220
25 ½ NPT 62 260
40 ½ NPT 67 310
50 ½ NPT 79 452
62 Endress+Hauser
Proline Promass F 200
Order code for "Housing", options B "GT18 two-chamber, 316L"; C "GT20 two-chamber aluminum-
coated"
A D
B C E F
H
I
G
K
L
A0017733
DN A B 1) C D 2) E F 2) G H 3) I 3) K L
[in] [in] [in] [in] [in] [in] [in] [in] [in] [in] [in] [in]
4)
³⁄₈ 6.38 4.02 2.36 6.50 2.95 3.54 0.21 10.55 13.5 2.95
4)
½ 6.38 4.02 2.36 6.50 2.95 3.54 0.33 10.55 13.5 2.95
4)
1 6.38 4.02 2.36 6.50 2.95 3.54 0.47 10.55 13.5 2.95
4)
1½ 6.38 4.02 2.36 6.50 2.95 3.54 0.69 10.75 14.88 4.13
4)
2 6.38 4.02 2.36 6.50 2.95 3.54 1.02 11.14 16.69 5.55
4)
3 6.38 4.02 2.36 6.50 2.95 3.54 1.59 11.89 19.76 7.87
Endress+Hauser 63
Proline Promass F 200
Flange connections
C
A
B
E
D L
A0029370
DN A B C D E L
[in] [in] [in] [in] [in] [in] [in]
Flange according to ASME B16.5: Class 150 with reduction in nominal diameter
1.4404 (F316/F316L)
64 Endress+Hauser
Proline Promass F 200
DN A B C D E L
[in] [in] [in] [in] [in] [in] [in]
Flange according to ASME B16.5: Class 300 with reduction in nominal diameter
1.4404 (F316/F316L)
DN A B C D E L
[in] [in] [in] [in] [in] [in] [in]
Endress+Hauser 65
Proline Promass F 200
C
A
B
E
F
D L
A0029372
DN A B C D E F L Ldiff 1)
[in] [in] [in] [in] [in] [in] [in] [in] [in]
1) Difference to installation length of the welding neck flange (order code for "Process connection", option
AAC)
2) DN ³⁄₈" with DN ½" flanges as standard
DN A B C D E F L Ldiff 1)
[in] [in] [in] [in] [in] [in] [in] [in] [in]
1) Difference to installation length of the welding neck flange (order code for "Process connection", option
AAC)
2) DN ³⁄₈" with DN ½" flanges as standard
66 Endress+Hauser
Proline Promass F 200
DN A B C D E F L Ldiff 1)
[in] [in] [in] [in] [in] [in] [in] [in] [in]
1) Difference to installation length of the welding neck flange (order code for "Process connection", option
AAC)
2) DN ³⁄₈" with DN ½" flanges as standard
Endress+Hauser 67
Proline Promass F 200
Clamp connections
Tri-Clamp
B
L
A0029373
DN Clamp A B L
[in] [in] [in] [in] [in]
3A-version available: order code for "Additional approval", option LP in conjunction with
Ra ≤ 32 µin: order code for "Measuring tube material", option SB, SE or
Ra ≤ 16 µin: order code for "Measuring tube material", option SC, SF
DN Clamp A B L
[in] [in] [in] [in] [in]
3A-version available: order code for "Additional approval", option LP in conjunction with
Ra ≤ 32 µin: order code for "Measuring tube material", option SB, SE or
Ra ≤ 16 µin: order code for "Measuring tube material", option SC, SF
68 Endress+Hauser
Proline Promass F 200
Cable glands
A
B
L
A0029374
DN A B L
[in] [in] [in] [in]
3A-version available: order code for "Additional approval", option LP in conjunction with
Ra ≤ 0.8 µm: order code for "Measuring tube material", option SB, SE
Endress+Hauser 69
Proline Promass F 200
VCO
B
L
A0029376
8-VCO-4 (½")
1.4404 (316/316L)
Order code for "Process connection", option CVS
DN A B L
[in] [in] [in] [in]
12-VCO-4 (¾")
1.4404 (316/316L)
Order code for "Process connection", option CWS
DN A B L
[in] [in] [in] [in]
½ AF 1½ 0.62 12.01
70 Endress+Hauser
Proline Promass F 200
Accessories
45° L
H
G
A0002537
DN G H L
Weight in SI units
All values (weight) refer to devices with EN/DIN PN 40 flanges. Weight information in [kg].
DN Weight [kg]
[mm]
Order code for "Housing", option C Order code for "Housing", option B
Aluminum coated 1.4404 (316L)
8 9 11.5
15 10 12.5
25 12 14.5
40 17 19.5
50 28 30.5
80 53 55.5
Weight in US units
All values (weight) refer to devices with EN/DIN PN 40 flanges. Weight information in [lbs].
DN Weight [lbs]
[in]
Order code for "Housing", option C Order code for "Housing", option B
Aluminum coated 1.4404 (316L)
3/8 20 25
½ 22 28
1 26 32
Endress+Hauser 71
Proline Promass F 200
DN Weight [lbs]
[in]
Order code for "Housing", option C Order code for "Housing", option B
Aluminum coated 1.4404 (316L)
1½ 37 43
2 62 67
3 117 122
3
A0020640
Adapter for cable entry with For non-Ex and Ex Stainless steel, 1.4404 (316L)
internal thread G ½" (except for CSA Ex d/XP)
72 Endress+Hauser
Proline Promass F 200
Adapter for cable entry with For non-Ex and Ex Nickel-plated brass
internal thread NPT ½" (except for CSA Ex d/XP)
Device plug
Sensor housing
• Acid and alkali-resistant outer surface
• Stainless steel, 1.4301/1.4307 (304L)
optional order code for "Sensor option", option CC: stainless steel, 1.4404 (316/316L)
Measuring tubes
• DN 8 to 80 (3/8 to 3"): stainless steel, 1.4539 (904L); manifold: stainless steel, 1.4404
(316/316L)
• DN 8 to 80 (3/8 to 3"): Alloy C22, 2.4602 (UNS N06022); manifold: Alloy C22, 2.4602 (UNS
N06022)
Process connections
• Flanges according to EN 1092-1 (DIN2501) / according to ASME B 16.5 / as per JIS B2220:
– Stainless steel, 1.4404 (F316/F316L)
– Alloy C22, 2.4602 (UNS N06022)
– Lap joint flanges: stainless steel, 1.4301 (F304); wetted parts Alloy C22
• All other process connections:
Stainless steel, 1.4404 (316/316L)
List of all available process connections → 74
Seals
Welded process connections without internal seals
Accessories
Endress+Hauser 73
Proline Promass F 200
Operability
Operating concept Operator-oriented menu structure for user-specific tasks
• Commissioning
• Operation
• Diagnostics
• Expert level
Quick and safe commissioning
• Guided menus ("Make-it-run" wizards) for applications
• Menu guidance with brief explanations of the individual parameter functions
Reliable operation
• Operation in the following languages:
– Via local display:
English, German, French, Spanish, Italian, Dutch, Portuguese, Polish, Russian, Swedish, Turkish,
Chinese, Japanese, Bahasa (Indonesian), Vietnamese, Czech
– Via "FieldCare" operating tool:
English, German, French, Spanish, Italian, Chinese, Japanese
• Uniform operating philosophy applied to device and operating tools
• If replacing the electronic module, transfer the device configuration via the integrated memory
(integrated HistoROM) which contains the process and measuring device data and the event
logbook. No need to reconfigure.
Efficient diagnostics increase measurement availability
• Troubleshooting measures can be called up via the device and in the operating tools
• Diverse simulation options, logbook for events that occur and optional line recorder functions
74 Endress+Hauser
Proline Promass F 200
Order code for "Display; Operation", option C "SD02" Order code for "Display; Operation", option E "SD03"
1 1
– –
+ +
E E
A0015544 A0015546
Display elements
• 4-line display
• With order code for "Display; operation", option E:
White background lighting; switches to red in event of device errors
• Format for displaying measured variables and status variables can be individually configured
• Permitted ambient temperature for the display: –20 to +60 °C (–4 to +140 °F)
The readability of the display may be impaired at temperatures outside the temperature range.
Operating elements
• With order code for "Display; operation", option C:
Local operation with 3 push buttons: , , E
1 2 3
A0013137
Endress+Hauser 75
Proline Promass F 200
6 8
3
2
1 4 5 7
A0013764
1 2 3
7 6 7 6 7 6
A0019013
76 Endress+Hauser
Proline Promass F 200
1 1 2
3
4
5
6 6
7 8 9 8 9 7 8 9 8 9
A0023460
3 –
+
E
2 1
A0014019
1 Service interface (CDI = Endress+Hauser Common Data Interface) of the measuring device
2 Commubox FXA291
3 Computer with "FieldCare" operating tool with COM DTM "CDI Communication FXA291"
Endress+Hauser 77
Proline Promass F 200
C-Tick symbol The measuring system meets the EMC requirements of the "Australian Communications and Media
Authority (ACMA)".
Ex approval The measuring device is certified for use in hazardous areas and the relevant safety instructions are
provided in the separate "Safety Instructions" (XA) document. Reference is made to this document on
the nameplate.
The separate Ex documentation (XA) containing all the relevant explosion protection data is
available from your Endress+Hauser sales center.
ATEX/IECEx
Currently, the following versions for use in hazardous areas are available:
Ex d
Category (ATEX) Type of protection
Ex ia
Category (ATEX) Type of protection
Ex nA
Category (ATEX) Type of protection
78 Endress+Hauser
Proline Promass F 200
Ex ic
Category (ATEX) Type of protection
CCSAUS
Currently, the following versions for use in hazardous areas are available:
IS (Ex i) and XP (Ex d)
Class I, II, III Division 1 Groups ABCDEFG
For sensors with nominal diameter DN 80: Class I, II, III Division 1 Groups CDEFG
NI (Ex nA, Ex nL)
• Class I Division 2 Groups ABCD
• Class II, III Division 1 Groups EFG
Functional safety The measuring device can be used for flow monitoring systems (min., max., range) up to SIL 2
(single-channel architecture) and SIL 3 (multichannel architecture with homogeneous redundancy)
and is independently evaluated and certified by the TÜV in accordance with IEC 61508.
The following types of monitoring in safety equipment are possible:
• Mass flow
• Volume flow
• Density
Functional Safety Manual with information on the SIL device → 85
Pressure Equipment The devices can be ordered with or without a PED approval. If a device with a PED approval is
Directive required, this must be explicitly stated in the order. For devices with nominal diameters less than or
equal to DN 25 (1"), this is neither possible nor necessary.
Endress+Hauser 79
Proline Promass F 200
• With the PED/G1/x (x = category) marking on the sensor nameplate, Endress+Hauser confirms
compliance with the "Essential Safety Requirements" specified in Annex I of the Pressure
Equipment Directive 97/23/EC.
• Devices bearing this marking (PED) are suitable for the following types of medium:
– Media in Group 1 and 2 with a vapor pressure greater than, or smaller and equal to0.5 bar
(7.3 psi)
– Unstable gases
• Devices not bearing this marking (PED) are designed and manufactured according to good
engineering practice. They meet the requirements of Art.3 Section 3 of the Pressure Equipment
Directive 97/23/EC. The range of application is indicated in tables 6 to 9 in Annex II of the
Pressure Equipment Directive.
80 Endress+Hauser
Proline Promass F 200
Ordering information
Detailed ordering information is available from the following sources:
• In the Product Configurator on the Endress+Hauser website: www.endress.com → Select your
country → Products → Select measuring technology, software or components → Select the product
(picklists: measurement method, product family etc.) → Device support (right-hand column):
Configure the selected product → The Product Configurator for the selected product opens.
• From your Endress+Hauser Sales Center: www.addresses.endress.com
Product Configurator - the tool for individual product configuration
• Up-to-the-minute configuration data
• Depending on the device: Direct input of measuring point-specific information such as
measuring range or operating language
• Automatic verification of exclusion criteria
• Automatic creation of the order code and its breakdown in PDF or Excel output format
• Ability to order directly in the Endress+Hauser Online Shop
Application packages
Many different application packages are available to enhance the functionality of the device. Such
packages might be needed to address safety aspects or specific application requirements.
The application packages can be ordered with the device or subsequently from Endress+Hauser.
Detailed information on the order code in question is available from your local Endress+Hauser sales
center or on the product page of the Endress+Hauser website: www.endress.com.
Detailed information on the application packages:
Special Documentation on the device → 85
HistoROM extended Comprises extended functions concerning the event log and the activation of the
function measured value memory.
Event log:
Memory volume is extended from 20 message entries (basic version) to up to 100
entries.
Data logging (line recorder):
• Memory capacity for up to 1000 measured values is activated.
• 250 measured values can be output via each of the 4 memory channels. The
recording interval can be defined and configured by the user.
• Data logging is visualized via the local display or FieldCare.
Accessories
Various accessories, which can be ordered with the device or subsequently from Endress+Hauser, are
available for the device. Detailed information on the order code in question is available from your
local Endress+Hauser sales center or on the product page of the Endress+Hauser website:
www.endress.com.
Endress+Hauser 81
Proline Promass F 200
Accessories Description
Promass 200 transmitter Transmitter for replacement or storage. Use the order code to define the following
specifications:
• Approvals
• Output
• Display / operation
• Housing
• Software
Accessories Description
Heating jacket Is used to stabilize the temperature of the fluids in the sensor.
Water, water vapor and other non-corrosive liquids are permitted for use as fluids.
If using oil as a heating medium, please consult with Endress+Hauser.
Heating jackets cannot be used with sensors fitted with a rupture disk.
82 Endress+Hauser
Proline Promass F 200
BA00371F
For details, see "Technical Information" TI00429F and Operating Instructions
Wireless HART adapter Is used for the wireless connection of field devices.
SWA70 The WirelessHART adapter can be easily integrated into field devices and existing
infrastructures, offers data protection and transmission safety and can be operated
in parallel with other wireless networks with minimum cabling complexity.
BA00053S
For details, see "Technical Information" TI00025S and Operating Instructions
Fieldgate FXA520 Gateway for the remote diagnostics and remote configuration of connected HART
measuring devices via a Web browser.
Field Xpert SFX350 Field Xpert SFX350 is a mobile computer for commissioning and maintenance. It
enables efficient device configuration and diagnostics for HART and FOUNDATION
Fieldbus devices in the non-Ex area.
Endress+Hauser 83
Proline Promass F 200
Memograph M graphic The Memograph M graphic display recorder provides information on all relevant
display recorder measured variables. Measured values are recorded correctly, limit values are
monitored and measuring points analyzed. The data are stored in the 256 MB
internal memory and also on a SD card or USB stick.
BA00247R
For details, see "Technical Information" TI00133R and Operating Instructions
RN221N Active barrier with power supply for safe separation of 4-20 mA standard signal
circuits. Offers bidirectional HART transmission.
BA00202R
For details, see "Technical Information" TI00073R and Operating Instructions
RNS221 Supply unit for powering two 2-wire measuring devices solely in the non-Ex area.
Bidirectional communication is possible via the HART communication jacks.
Cerabar M The pressure transmitter for measuring the absolute and gauge pressure of gases,
steam and liquids. It can be used to read in the operating pressure value.
Cerabar S The pressure transmitter for measuring the absolute and gauge pressure of gases,
steam and liquids. It can be used to read in the operating pressure value.
BA00271P
For details, see "Technical Information" TI00383P and Operating Instructions
Documentation
For an overview of the scope of the associated Technical Documentation, refer to the following:
• The W@M Device Viewer : Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate or scan the
2-D matrix code (QR code) on the nameplate.
84 Endress+Hauser
Proline Promass F 200
Operating Instructions
Documentation code
ATEX/IECEx Ex i XA00144D
ATEX/IECEx Ex d XA00143D
ATEX/IECEx Ex nA XA00145D
cCSAus IS XA00151D
cCSAus XP XA00152D
INMETRO Ex i XA01300D
INMETRO Ex d XA01305D
INMETRO Ex nA XA01306D
NEPSI Ex i XA00156D
NEPSI Ex d XA00155D
NEPSI Ex nA XA00157D
Special Documentation
Installation Instructions
Installation Instructions for spare part sets Specified for each individual accessory
Registered trademarks
HART®
Registered trademark of the HART Communication Foundation, Austin, USA
PROFIBUS®
Registered trademark of the PROFIBUS User Organization, Karlsruhe, Germany
FOUNDATIONTM Fieldbus
Registration-pending trademark of the Fieldbus Foundation, Austin, Texas, USA
TRI-CLAMP®
Registered trademark of Ladish & Co., Inc., Kenosha, USA
Applicator®, FieldCare®, Field XpertTM, HistoROM®, Heartbeat TechnologyTM
Registered or registration-pending trademarks of the Endress+Hauser Group
Endress+Hauser 85
www.addresses.endress.com