Professional Documents
Culture Documents
Crown and Bridge Quiz - Attempt 2 by Jennifer Loppnow - 5/21/2021 1:30:11 AM - Failed - 45%
Crown and Bridge Quiz - Attempt 2 by Jennifer Loppnow - 5/21/2021 1:30:11 AM - Failed - 45%
Online Study System for the Certified Dental
Technician and Recognized Graduate Examinations
Crown and Bridge Quiz - Attempt 2 by Jennifer Loppnow - 5/21/2021 1:30:11 AM - Failed - 45%
All Learning Objectives 20 9/20
Which of the following will frequently cause porcelain chipping to chip on a zirconia framework?
Correct Yours
1 inadequate framework design
0 points applying polishing paste
using a water cooled handpiece
using diamond tools at low speed
What is the purpose of centrically balanced occlusion?
Correct Yours
2
have contacts made simultaneously and with equal force
1 point avoid impinging on the cheeks and tongue
prevent the wear of cusp tips
What is the purpose of using wetting agents on dental impressions prior to pouring?
Correct Yours
3 increases the density of the stone
0 points reduces the number of surface bubbles
makes the stone flow faster
prevents the stone from sticking to the impression
What is an important factor in choosing a pre-solder?
Correct Yours
4 melting range
1 point type of flux
grain size
welding ability
Tripoli is less abrasive than rouge.
5 Correct Yours
1 point true
false
Which action would cause abrasion to the die?
Correct Yours
6 not applying die hardener
1 point applying too much die spacer
applying separator on the die
finishing the crown on the die
Which type of pontic design would be the easiest for the patient to keep clean?
Correct Yours
7
ridge lap
0 points sanitary
saddle
In which relationship is the mandibular arch wider than the maxillary arch?
Correct Yours
8
overjet
1 point overbite
crossbite
Which of the following is true regarding a cusp-fossa relationship?
Correct Yours
9
The patient is placed in a balanced occlusion.
1 point Cusp tips do not actually occlude with opposing dentition.
The patient's anterior guidance protects cusp tips.
Which of the following is a simple hinge type articulator?
Correct Yours
10 non-adjustable
1 point semi-adjustable
fully adjustable
Fixed-adjustable articulator.
When polishing a soldered or welded joint, polishing compound should be used with a
Correct Yours
11 chamois cloth and rubbed by hand.
0 points chamois wheel on high speed.
buffing wheel on high speed.
buffing wheel on low speed.
When preparing the metal on a ceramic bridge for laser welding, the joint surfaces should be oxidized.
12 Correct Yours
0 points true
false
What is the ideal thickness of wax to be pressed to a metal coping?
Correct Yours
13 .3 mm
1 point .5 mm
.8 mm
1.0 mm
What is the proper term to describe the direct joining of parent metals?
Correct Yours
14 soldering
0 points melting
welding
interfacing
Which of the following teeth have single antagonists?
Correct Yours
15 maxillary lateral incisors
0 points mandibular central incisors
mandibular primary canines
mandibular third molars
Margin design is the most important consideration for a lithium disilicate bridge.
16 Correct Yours
0 points true
false
What is the Ideal proximal contact on a posterior tooth?
Correct Yours
17 point just below the marginal ridge.
0 points area just below the marginal ridge.
area at the marginal ridge.
point at the marginal ridge.
When the mesiobuccal cusp of the maxillary first molar in alignment with the embrasure of the mandibular second premolar and first
molar is in what type of occlusion?
Correct Yours
18
class I
1 point class II
class III
class IV
Which type of the following waxes is hardest?
Correct Yours
19 utility wax strips
0 points boxing wax
type I inlay wax
type II inlay wax
To prevent excess stone in the tongue of a mandibular cast, it is necessary to bead the impression 3 mm from the periphery.
20 Correct Yours
0 points true
false