Professional Documents
Culture Documents
SERVICE MANUAL
US Model
Ver. 1.2 2009.03 Canadian Model
Revision History AEP Model
E Model
Revised-2 Chinese Model
Replacement of the previously issued
Japanese Model
SERVICE MANUAL 9-852-266-12
with this manual.
Link
SPECIFICATIONS FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST
BLOCK DIAGRAMS
2009C0500-1
HVR-MRC1 © 2009.3
9-852-266-13 Sony EMCS Co. Published by Kohda TEC
Downloaded from www.Manualslib.com manuals search engine
ENGLISH JAPANESE
SPECIFICATIONS
System General
File system FAT32 Power requirement DC 7.2 V (battery pack)
CompactFlash 133x 2 GB or more DC 8.4 V (AC adaptor)
The capacity is the value when 1 Power consumption 2.2 W
GB equals 1 billion bytes. Operating temperature 0 °C to 40 °C (32 °F to 104 °F)
The actual usable capacity may Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)
be slightly less because Operating humidity 20 % (20 °C) to 90 % (35 °C)
administrative files etc. are (no condensation)
included. Dimensions
File format HDV recording MPEG-2TS HVR-MRC1 : Approx. 57 × 102 × 34 mm
(.m2t) (2 1/4 × 4 × 1 3/8 in.)
DVCAM/DV recording HVR-MRC1+HVRA-CR1: Approx. 77 × 106 × 51 mm
AVI-Type1 (3 × 4 1/8 × 2 in.)
(.AVI) (including the projecting parts)
RAW DV (.DV) (w/h/d)
Input signal Mass
HDV recording/playback HVR-MRC1 : Approx. 130 g (4.5 oz)
Video: MPEG-2TS HVR-MRC1+HVRA-CR1: Approx. 210 g (7.4 oz)
1080/60i, 30p, 24p (excluding CompactFlash and
1080/50i, 25p battery pack)
Audio: 2 CH MPEG 1 Audio Input/output jack i.LINK
Layer2 Stereo (16 bit 48 kHz) (IEEE1394 6-pin connector S400)
(1/2 CH)
4 CH MPEG 2 Audio Optional accessories AC adaptor/charger
Layer2 Stereo (16 bit 48 kHz) AC-VQ1050B
(3/4 CH) Battery pack
DVCAM/DV recording/playback NP-F570/F770/F970
Video: DV embedded
Audio: PCM digital Design and specifications are subject to change without
(12/16 bit, 32k, 48k) notice.
Recordable time 2 GB Approx. 9 minutes
4 GB Approx. 18 minutes
8 GB Approx. 36 minutes
16 GB Approx. 72 minutes
HVR-MRC1
—2—
Downloaded from www.Manualslib.com manuals search engine
ENGLISH JAPANESE
概略仕様
本機の仕様および外観は、 改良のため予告なく変更すること
がありますが、 ご了承ください。
HVR-MRC1
—3—
Downloaded from www.Manualslib.com manuals search engine
ENGLISH JAPANESE
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
: LEAD FREE MARK
transistors, that were installed during a previous repair. Point
Unleaded solder has the following characteristics.
them out to the customer and recommend their replacement.
• Unleaded solder melts at a temperature about 40°C higher than
4. Look for parts which, through functioning, show obvious signs ordinary solder.
of deterioration. Point them out to the customer and Ordinary soldering irons can be used but the iron tip has to be
recommend their replacement. applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350°C.
• Keep the temperature of the soldering iron around 270˚C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
• Do not touch the soldering iron on the same conductor of the • Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
circuit board (within 3 times).
ordinary solder so use caution not to let solder bridges occur such
• Be careful not to apply force on the conductor when soldering as on IC pins, etc.
or unsoldering. • Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
HVR-MRC1
—4—
Downloaded from www.Manualslib.com manuals search engine
ENGLISH JAPANESE
サービス,点検時には次のことにご注意下さい。
1. 注意事項をお守りください。 6. フレキシブルプリント基板の取扱いについて
サービスのとき特に注意を要する個所については, • コテ先温度を270℃前後にして行なって下さい。
キャビネット,シャーシ,部品などにラベルや捺印で • 同一パターンに何度もコテ先を当てないで下さい。
注意事項を表示しています。これらの注意書き及び取 (3回以内)
扱説明書等の注意事項を必ずお守り下さい。 • パターンに力が加わらないよう注意して下さい。
2. 指定部品のご使用を 7. 無鉛半田について
セットの部品は難燃性や耐電圧など安全上の特性を 無鉛半田を使用している基板には,無鉛(Lead Free)を意
持ったものとなっています。従って交換部品は,使用 味するレッドフリーマークがプリントされています。
されていたものと同じ特性の部品を使用して下さい。 (注意: 基板サイズによっては,無鉛半田を使用して
特に回路図,部品表に0印で指定されている安全上重要 いてもレッドフリーマークがプリントされて
な部品は必ず指定のものをご使用下さい。 いないものがあります)
3. 部品の取付けや配線の引きまわしはもとどおりに :レッドフリーマーク
安全上,チューブやテープなどの絶縁材料を使用した 無鉛半田には,以下の特性があります。
り,プリント基板から浮かして取付けた部品がありま • 融点が従来の半田よりも約40℃高い。
す。また内部配線は引きまわしやクランパによって発 従来の半田こてをそのまま使用することは可能です
熱部品や高圧部品に接近しないよう配慮されています が,少し長めにこてを当てる必要があります。
ので,これらは必ずもとどおりにして下さい。 温度調節機能のついた半田こてを使用する場合,約
4. サービス後は安全点検を 350℃に設定して下さい。
サービスのために取外したネジ,部品,配線がもとど 注意: 半田こてを長く当てすぎると,基板のパター
おりになっているか,またサービスした個所の周辺を ン(銅箔)がはがれてしまうことがあります
劣化させてしまったところがないかなどを点検し,安 ので,注意して下さい。
全性が確保されていることを確認して下さい。 • 粘性が強い
5. チップ部品交換時の注意 従来の半田よりも粘性が強いため,IC端子などが半田
• 取外した部品は再使用しないで下さい。 ブリッジしないように注意して下さい。
• タンタルコンデンサのマイナス側は熱に弱いため交 • 従来の半田と混ぜて使用可能
換時は注意して下さい。 無鉛半田には無鉛半田を追加するのが最適ですが,
従来の半田を追加しても構いません。
HVR-MRC1
—5—
Downloaded from www.Manualslib.com manuals search engine
1. SERVICE NOTE ENGLISH JAPANESE
Method:
Use the DC input terminal. (AC power adaptor/changer (AC-VQ1050B) and DK cable).
X Y y ZZ
i LINK I: Main 1y Physical Y1 When error is defined
ATA A: Sub 2y Logical Y2 in the devise, the error
Power Supply P: Other 9y Other Y9 code of it is displayed.
MPEG/AVI M:
Other X:
Fatal Error F:
Self-diagnosis Code
Cause Corrective Action
X Yy ZZ
Cash overflow by transfer rate delay of
A 12 01 Be sure that the CompactFlash you are using is the recommended type.
CompactFlash.
A 12 02 The selection clip is not found. Be sure that the CompactFlash you are using is the recommended type.
Reformat the CompactFlash using this unit again, after reformatting
A 12 03 The filesystem of CompactFlash is broken.
the CompactFlash using personal computer.
A 19 91 CompactFlash recognition error Check the type you are using.
I 12 ** Error related to i.LINK Turn this unit off and then back on.
It is generated the error by the power supply
P 12 ** Turn this unit off and then back on.
control from main CPU to sub CPU.
It is generated the error by the power
P 21 01 supply control from sub CUP to each Turn this unit off and then back on.
device.
P 21 02 It could not enter to the sleep mode. Turn this unit off and then back on.
M 12 ** The input video stream is abnormal. Turn this unit off and then back on.
The recording animation could not
M 21 ** Turn this unit off and then back on.
correctly treat.
Communication abnormality between
F 11 01 Turn this unit off and then back on.
CompactFlash and main CPU.
F 11 02 i.LINK error. Turn this unit off and then back on.
F 12 ** It abnormal is generated by the file system. Reformat the CompactFlash using this unit.
F 20 01 Reset failure of PHY (Physical Layer) There is particularly no solution
Main CPU cannot be communicated with
F 21 ** Turn this unit off and then back on.
sub CPU.
F 22 ** Sub CPU cannot control each device. Turn this unit off and then back on.
F 29 00 Sub CPU farm is not written. Turn this unit off and then back on.
F 91 ** Fatal error of originating hardware. Turn this unit off and then back on.
F 92 ** Fatal error of originating software. Turn this unit off and then back on.
X 91 85 Reception buffer overflow. Turn this unit off and then back on.
X 99 ** Error code of main CPU firmware. Turn this unit off and then back on.
Note: ** is arbitrary value.
HVR-MRC1
1-1
Downloaded from www.Manualslib.com manuals search engine
ENGLISH JAPANESE
1-1. 修理時の電源供給について
本機では,安定化電源(8.4Vdc)からバッテリ端子に電源を供給した場合,約 10 秒後にシャットオフし,動作しなくなります。
これを避けるため,下記の方法を用いてください。
方法:
DC入力端子を使用する。(ACアダプタ/チャージャ(AC-VQ1050)とDKケーブルを使用する。)
1-2. 自己診断機能
エラーが発生した場合は,エラー内容に合わせて LCD 画面にエラーコードが表示されます。
また,カメラ側にエラーコードが送信されます。
LCD画面
ERROR
A:12:01
自己診断表示:X:Yy:ZZ
X Y y ZZ
i.LINK I: メイン 1y フィジカル Y1 デバイスにエラーの
規定があれば,その
ATA A: サブ 2y ロジカル Y2 コードを表示する。
電源 P: その他 9y その他 Y9
MPEG/AVI M:
その他 X:
致命的なエラー F:
自己診断コード
原因 対処
X Yy ZZ
コンパクトフラッシュの転送速度遅延に
A 12 01 使用のコンパクトフラッシュが推奨のカードか確認する。
よるキャッシュオーバーフロー。
A 12 02 選択クリップが見つからない。 使用のコンパクトフラッシュが推奨のカードか確認する。
コンパクトフラッシュのファイルシステ パソコンでコンパクトフラッシュのフォーマットを行った
A 12 03 後,本機で再度コンパクトフラッシュのフォーマットを行
ムが壊れている。 う。
A 19 91 コンパクトフラッシュ認識エラー。 電源を切り,再度電源を入れ直す。
I 12 ** i.LINK関連のエラー。 電源を切り,再度電源を入れ直す。
メインCPUからサブCPUへの電源制御で
P 12 ** エラー発生。 電源を切り,再度電源を入れ直す。
サブCUPから各デバイスへの電源制御で
P 21 01 エラー発生。 電源を切り,再度電源を入れ直す。
P 21 02 スリープモードに入れなかった。 電源を切り,再度電源を入れ直す。
M 12 ** 入力ビデオストリーム異常。 電源を切り,再度電源を入れ直す。
M 21 ** 記録動画を正しく処理できなかった 電源を切り,再度電源を入れ直す。
コンパクトフラッシュ−メインCPU間通
F 11 01 信異常。 電源を切り,再度電源を入れ直す。
F 11 02 i.LINKエラー。 電源を切り,再度電源を入れ直す。
F 12 ** ファイルシステムで異常発生。 本機でコンパクトフラッシュのフォーマットを行う。
F 20 01 PHY(Physical Layer)のリセット失敗。 電源を切り,再度電源を入れ直す。
メインCPUがサブCPUとの通信ができな
F 21 ** い。 電源を切り,再度電源を入れ直す。
F 22 ** サブCPUが各デバイスを制御できない。 電源を切り,再度電源を入れ直す。
サブC P U ファームが書き込まれていな
F 29 00 い。 特になし
F 91 ** ハードウェア起因の致命的なエラー。 電源を切り,再度電源を入れ直す。
F 92 ** ソフトウェア起因の致命的なエラー。 電源を切り,再度電源を入れ直す。
X 91 85 受信バッファオーバーフロー。 電源を切り,再度電源を入れ直す。
メインCPUファームウェアのエラーコー
X 99 ** ド。 電源を切り,再度電源を入れ直す。
注:** は任意の値。
HVR-MRC1
1-2E
Downloaded from www.Manualslib.com manuals search engine
2. DISASSEMBLY
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt
Do not insert the cable insufficiently nor crookedly. which comes off at the point.
(Be careful or some
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped. pieces of gilt may be left inside)
HVR-MRC1
2-1
Downloaded from www.Manualslib.com manuals search engine
2-1. IDENTIFYING PARTS
CF Base Cabinet
⋅ FP-202 Flexible Board
CF Main Cabinet
⋅ CF-110 Board
⋅ FP-201 Flexible Board
⋅ LC-095 Board
⋅ TK-071 Board
CF Door
⋅ SW-525 Board
- DISASSEMBLY FLOW -
2-2-1. BASE CABINET SECTION 2-2-2. MAIN CABINET SECTION
⋅ CF Base Cabinet ⋅ CF-110 Board
⋅ TK-071 Board ⋅ LCD Block
⋅ SW-525 Board
i.LINK Cradle
Cabinet (BATT)
Cabinet (CF)
⋅ CR-090 Board
- DISASSEMBLY FLOW -
2-2-3. ADAPTOR SECTION
⋅ CR-090 Board
⋅ Cabinet (BATT)
HVR-MRC1
2-2
Downloaded from www.Manualslib.com manuals search engine
HELP
2-2. DISASSEMBLY
EXPLODED VIEW HARDWARE LIST
2-2-1. BASE CABINET SECTION
Follow the disassembly in the numerical order given.
1 CF Base Cabinet (1-1 to 1-4)
2 TK-071 Board (2-1 to 2-5)
1-1 (#53)
1 CF Base Cabinet
1-4
2-2
2-1 (#46)
2 TK-071 Board
2-3
1-3 (Claw)
HVR-MRC1
2-3
Downloaded from www.Manualslib.com manuals search engine
2-2-2. MAIN CABINET SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 CF-110 Board (1-1 to 1-5)
2 LCD Block (2-1 to 2-2)
3 SW-525 Board (3-1 to 3-9)
1-2 (#46)
1-3 (#11)
1-5
1 CF-110 Board
C
F
-1
10
1-1 2-1
2 LCD Block
3-7 (#11)
Note: Don't touch grease.
3-3 (#11)
A
3-6 (#46)
3-8
3-4
(Boss)
S
3-1
W
-5
25
2-2
3-2
(#2)
3-9
3-5
1-4 (Open)
HVR-MRC1
2-4
Downloaded from www.Manualslib.com manuals search engine
2-2-3. ADAPTOR SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 CR-090 Board (1-1 to 1-10)
2 Cabinet (BTT) (2-1 to 2-6)
1-1 (#2)
2 Cabinet (BTT)
2-5
(Open)
2-3
1-4
HELP
1-3
2-6
HELP
2-2
2-1 (#12)
2-4
(#12) 1-6 1-5 (#12)
1-9 (#12)
1 CR-090 Board
1-10
1-2 (#12)
HVR-MRC1
2-5
Downloaded from www.Manualslib.com manuals search engine
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
Hook
HVR-MRC1
HELP
Downloaded from www.Manualslib.com manuals search engine
3. BLOCK DIAGRAMS
Link
HVR-MRC1
18 - 20 2 - 6, 21 - 23, 27 - 31, 47 - 49
HDV/DV HOT HOT CN4001 CN8002
4, 6 - 9, 11 ,40 - 49
CN9004
15, 14, 18, 17
A10, A11,
HDV-i.LINK, DV-i.LINK HDV-i.LINK, DV-i.LINK
C11, B11
C7, A6,
B7, A7,
37 - 34
6 - 13
6-3
TPA+, TPA-, TPB+, TPB- TPA+, TPA-, TPB+, TPB- LD[0] - LD[7] DD[1] - DD[15] D00 - D15 D00 - D15
A5, B6
CTL0, CTL1
4, 5
IC4003
PCLK
W9, Y10, V9
HDV/DV i.LINK 2 C6
39, 37, 35
13, 15, 17
INTERFACE LREQ
1 D7
(1/5) LPS DA0 - DA2 A00 - A02 A00 - A02
15 A12
LKON
19 B12 COMPACT
59
X4001 CNA #CS0 xCS0 xCS0 FLASH
3 U9 13 39 7
24.576MHz #CS1 xCS1 xCS1
60 #RESET Y8 14 38 32
53 #DIOR xIORD xIORD
Y15 18 34 34
#DIOW xIORW xIORW
V14 20 32 35
INTRQ INTRQ INTRQ
Y11 24 28 37
IC1005 POR- IC4002 IORDY IORDY IORDY
S3.3V 4 1 2 4 W14 34 18 42
RESET BUFFER DMARQ xINPACK xINPACK
(5/5) (1/5) W15 36 16 43
#DMACK xREG xREG
W11 38 14 44
xDASP xDASP
40 12 45
xCD xCD1
IC1004 2 50 26
MRESET MRESET_R xCD2
M3.3V 4 RESET 1 V3 25
#RESET xRESET xRESET
(5/5) V10 32 20 41
SW-525 BOARD COVER_STAT
50 2
COVER_STAT
S7005
PLAY PLAY DDQ[0] - DDQ[31] IC3001
EXEC H 13 8 8 IC2003
PLAY REC RESET SWITCH 512M ENA ENA Q6001, Q6002
(4/5) DA[0] - DA[12] SDRAM 3 12 3 12
z LED DRIVE
SUB_S_RESET (3/5)
S7009 S7006 RESET 1 C1 D6001, D6002
40 4 CLKD
2 C9 J1 (BACKLIGHT)
REC_ON REC_ON IC2001
9 12 39
SUB CPU
D20, F18, E20
12
S7007 (4/5)
8, 1, 2
IC2004 (2/5)
S7010
4, 5, 3
ACV_UNREG 3.0V
H3.3V
SET_UNREG M3.3V
IC1001
M3.3VA
DC CONTROL S3.3V
(5/5)
P3.3V
1.8V
SW_OFF
A1.8V
A : VIDEO/AUDIO SIGNAL
05
HVR-MRC1
3-1
5, 6
5, 6
8, 9
1
DC IN MINUS_A
2 F9001 UNREG
MINUS_B UNREG R1042 F1002 Q1009
6, 7
3, 4
3, 4
6, 7
3
Q1011
Q1013
CN9001
D1004
BATT(+)
+ 1
SET_UNREG
BT901 SW
2
BATTERY
PWR_SUB_33
SIG Q1008
TERMINAL S 3 IC2001
SW_OFF
BATT(-)
− 4 SUB CPU
Q1007, Q1010 (4/5)
32 P20/ANI0
DC IN
DETECT PWR_P33
P75 6
DCIN_AD
25 P27/ANI7 P124/XT2/ 41 PWR_LCD
Q1003, Q1006
EXCLKS
BATTERY BATT_AD
26 P26/ANI6 P140/PCL/ 36 PWR_MAIN_33
DETECT
SW-525 BOARD IB_ENABLE
INTP6
33 P130 PWR_CF0
S7010 SLEEP P74 7
CN7001 CN2001 17 P15/TOH0
POWER SW_PWR SW_PWR SW_PWR CARD_DETECT
6 15 16 P16/TOH1 P33/TI51/ 5
/INTP5 TO51/INTP4
ON
SW_OFF_CN SW_OFF_CN
8 13
OFF
IC2003 IC1005
D7009 Q7001 3.3V 3.3V
REC LAMP, 3 18 RESET SWITCH RESET
R7001 LED DRIVE (5/5)
CF ACCESS FB2001 (4/5)
FB1006
S3.3V S3.3V POR- IC4002
2 VIN VOUT 3 4 VDD VOUT 1 2 4
5 VIN IC1002 BUFFER
(1/5)
3.3V REG R1025,
(5/5) Q1004 L1002 R1026 FB1005
A1.8V
SWITCHING
1.8V
FB4006
FB4002
SENSE1+ 30 Q1015
SENSE1- 31
IC1001 Vosense1 1 LC-095 BOARD
FB4003
FB4004
FB4005
FL4001
FL4002
FL4003
DC CONTROL
(5/5) Vosense2 9
#RESET
IC4003
28 RUN/SS1 15 LCD
SW2
HDV/DV i.LINK INTERFACE
BG2 18 IC1003 (1/5)
13 RUN/SS2 TG2 14 3V REG CF-110 BOARD
Q1001 (5/5) CN2002
R1023, CN8004 CN8003 R6004,
FB1003 FB1007 CN6002
R1024 3.0V 3.0V 3.0V Q6001, Q6002 R6005
SWITCHING 5 VIN VOUT 4 1 14 1 14
L1001 LED DRIVE
Q1005 CONT FB6001
IC3001 D6001, D6002
1 512M (BACKLIGHT)
PWR_LCD SDRAM
(3/5)
Q1017
FB1008
H3.3V
FP-201
FB3001
FB4001
PWR_CF FLEXIBLE
Q1018
BOARD
FB1009 CN4001 CN8002 CN8001
M3.3V
Vcc VCC
FB1010
IC2004 25 27 13
Vcc
POWER SWITCH PWR_MAIN_33 26 26 38
FB5001
FB5002
FB5004
FB5003
3.3V IC1004
RESET
(5/5)
IC5001 IC5002
M RESET
4 VDD VOUT 1 V3 RST- MAIN CPU EEPROM
(2/5) (2/5)
05
HVR-MRC1
3-2E
CN902
Attaching
CN903
FP-203
HOT SHOE HOT SHOE FLEXIBLE
BOARD
16 1 16 20
SW-525 BOARD
7
2 1
4 3
1 20 6 5
9 8
CN7001
FP-202
FLEXIBLE
FLEXIBLE FLAT CABLE
CN9005
BOARD 20 1
(FFC-157)
CN9004
HDV/DV
CR-090 BOARD
(SIDE A)
IC5002
20 1
(EEPROM)
(Not supplied)
CN2001
20 20 1
1 4 1 3
1 CN9001 CN9002
TK-071 BOARD TK-071 BOARD CN4002
(SIDE B) (SIDE A)
ND6001 BT901
LCD BATTERY
TERMINAL
2 50
1 14 1 CN4001 51
CN2002 S
J901
DC IN
1 49
CN6002
LC-095 BOARD LC-095 BOARD
(SIDE A) 14 1
(SIDE B)
1 51
FLEXIBLE FLAT CABLE
(FFC-159)
FP-201
FLEXIBLE
BOARD
14 1
CN8003
51 1
CF-110 BOARD CF-110 BOARD
(SIDE A) (SIDE B)
53 51
CN8004
1 14
26
2
CN8002
51
CN8001 50
COMPACT FLASH
CONNECTOR
(Compact Flash)
2
1
49
25
50
54 52
05
HVR-MRC1
4-1 FRAME
Link
TK-071 BOARD (1/5)
LC-095 BOARD (LCD)
(HDV/DV i.LINK INTERFACE)
HVR-MRC1
HVR-MRC1
4-2
Downloaded from www.Manualslib.com manuals search engine
4-2. SCHEMATIC DIAGRAMS ENGLISH JAPANESE
(JAPANESE)
回路図共通ノート
0印の部品,または0印付きの点線で囲まれた部品は,
(他に必要なノートは各ブロックに記載してあります) 安全性を維持するために重要な部品です。
【回路図ノート】 従って交換時は,必ず指定の部品を使用して下さい。
・ケミコン,タンタルを除くコンデンサで,耐圧50V以下のもの
はその耐圧を省略。単位はすべてμF(pはpF)。 お願い
・チップ抵抗で指示のないものは,1/10W以下。 図面番号で部品を指定するときは基板名又はブロック
を併せて指定して下さい。
kΩ=1000Ω,MΩ=1000kΩ
・チップ部品交換時の注意
取り外した部品は再使用せず,未使用の部品をご使用くださ
い。
タンタルコンデンサのマイナス側は熱に弱いため注意してくだ
さい。
・チップ部品には下記のように表示したものがあります。
例 C 541 L 452
22U 10UH
TA A 2520
↑ ↑ ↑
種類 ケースサイズ 外形寸法(mm)
・抵抗,コンデンサ,ICなど定数にXXがあるものは,使用して
いない事を示しています。このため,使用していない回路が記
載されている事があります。
・★印のある部品は,機種などにより異なりますので機能別マウ
ント一覧表を参照してください。
・可変抵抗と半固定抵抗で,B特性の表示を省略。
・信号名表記について,下記のような場合があります。
XEDIT → EDIT PB/XREC → PB/REC
・2は不燃性抵抗。
・1はヒューズ抵抗。
・Cはパネル表示名称。
・AはB+ライン。
・BはB−ライン。
・JはBライン(+,−)の入出力方向を示す。
・Cは調整名称。
【電圧・波形測定条件ノート】
・電圧値及び信号波形は測定点対アース間の参考値。
(デジタルマルチメータ;入力インピーダンス DC10MΩ使
用)
・使用テスタの入力インピーダンスにより電圧値が多少異なりま
す。
HVR-MRC1
4-3
Downloaded from www.Manualslib.com manuals search engine
1 2 3 4 5 6 7 8 9 10 11 12
A A
FB4001
H3.3V M3.3V S3.3V
R4040
R4043
100k
10k
IC4002
TC7S08FU(TE85R)
CN4001 51P
B R4044 BUFFER B
GND 1 SUB_TO_PHY
XX 3.3
R4001 33 CARD_DETECT 3.3
1
xCD 2 CARD_DETECT
R4002 33 DD[3] R4045 3.3
D03 POR-
2
3 DD[3] XX
3.3 R4049 R4051
R4003 33 DD[11] 1k
D11
3
4 DD[11] XX
R4004 33 DD[4]
D04 5 DD[4] C4005
10V
R4005 33 DD[12] 0.1u
D12 6 DD[12] B X4001
33 DD[5] R4046 24.576MHz
R4006
D05 7 DD[5] XX 1 2
C4007 25V
R4007 33 DD[13] 50V
D13 8 DD[13] 0.01u B C4008 CH 50V C4011
33 DD[6] 12p 3 4 CH
R4008 12p
D06 9 DD[6]
R4009 33 DD[14]
0
D14 10 DD[14]
R4056
R4057
R4010 33 DD[7]
D07 11 DD[7]
R4011 33 DD[15] FL4001
D15 12 DD[15] FB4002 FB4005 P3.3VA FB4006
33 1 2
C xCS0 13
R4012
#CS0 P3.3V P3.3V C
R4013 33 FB4004
xCS1 14 #CS1 3 4
0.1u B
B
R4034 10k
C4009
C4006
C4010
C4015 C4016
C4013
GND(A10) 15 4.7u
0.1u
0.1u
0.1u 4.7u
B B B 6.3V
GND(xVS1) 16 6.3V
GND(xATA_SEL) 17
3.3
3.3
1.5
1.5
3.3
1.3
3.3
3.3
3.3
R4015 22
0
xIORD 18 #DIOR
GND(A09) 19 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 CN4002 20P
R4016 22
NC
DGND4
DGND3
DVDD4
DVDD3
XO
XI
PLLGND2
PLLGND1
PLLVDD
FILTER1
FILTER0
#RESET
AVDD5
AVDD4
AGND6
AGND5
xIORW 20 #DIOW 1 REG_GND
C4002
H3.3VVV
GND(A08) 21 2 2 REG_GND
B 4
FL4003
CF-110 10V
CN8002 GND(xWE) 22 0.1u 3 REG_GND
Through the R4035 10k 3
GND(A07) 23 1 4 REG_GND
FP-201 Flexible 82 0
R4018
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
INTRQ INTRQ LREQ AGND4 N.C
1
25 PCLK SET_UNREG 6
D R0/P3.3 0.1u
0 D
Vcc 10k CNA TPA1+ UNREG
3
26 R4037 CNA B 7
1 R4070
Vcc(A06) CTL0 TPA1- ACV_UNREG
4
27 CTL0 ACV_UNREG 8
0 0.2 R4073 0
C4003 CTL1 ACV_UNREG
TPB1+
5
GND(xVS2) 30 LD[1] 11
R4038
B R4062
10k
4700
0
R4039
DGND2
DVDD2
AGND1
TESTM
AVDD1
AVDD2
R4027 XX
xPDIAG 42 #PDTAG
#ISO
D001
CPS
PC0
PC1
PC2
LND001 – LND020
3.3
3.3
3.3
3.3
3.3
SM
SE
1k
1k
D02 45 DD[2]
0
3.3
3.3
R4031 33 DD[9]
D09 46 DD[9]
FB4003
R4059
R4058
R4061
R4060
GND(xIOIS16) 47 B
R4032 33 DD[10] 0.1u
D10 48 DD[10] C4014 3 4
1 2
GND(xCD2) 49 LKON
0.1u
R4054
C4012
GND 51 XX
R4053 XX
R4052
XX
GND
G G
05
HVR-MRC1
4-4 TK-071 (1/5)
CLKD
DDQ[10]
DDQ[11]
DDQ[12]
DDQ[13]
DDQ[14]
DDQ[15]
DDQ[16]
DDQ[17]
DDQ[18]
DDQ[19]
DDQ[20]
DDQ[21]
DDQ[22]
DDQ[23]
DDQ[24]
DDQ[25]
DDQ[26]
DDQ[27]
DDQ[28]
DDQ[29]
DDQ[30]
DDQ[31]
CLKE
R5037 R5039 R5040 R5041
DDQ[0]
DDQ[1]
DDQ[2]
DDQ[3]
DDQ[4]
DDQ[5]
DDQ[6]
DDQ[7]
DDQ[8]
DDQ[9]
M3.3V
DA[12]
DA[11]
DA[10]
FB5001
DA[9]
DA[8]
DA[7]
DA[6]
DA[5]
DA[4]
DA[3]
DA[2]
DA[1]
DA[0]
10k 10k 10k 10k
1.8V
DQM3
DQM2
DQM1
DQM0
JL5001 TMS
#RAS
#CAS
#WE
1.8V 33
56
#CS
BA1
BA0
DDQ[10]
DDQ[11]
DDQ[12]
DDQ[13]
DDQ[14]
DDQ[15]
DDQ[16]
DDQ[17]
DDQ[18]
DDQ[19]
DDQ[20]
DDQ[21]
DDQ[22]
DDQ[23]
DDQ[24]
DDQ[25]
DDQ[26]
DDQ[27]
DDQ[28]
DDQ[29]
DDQ[30]
DDQ[31]
R5022
R5024
DDQ[0]
DDQ[1]
DDQ[2]
DDQ[3]
DDQ[4]
DDQ[5]
DDQ[6]
DDQ[7]
DDQ[8]
DDQ[9]
JL5003 TDI
C5001
4.7u B
6.3V JL5004 TDO
A C5002
A
10u B P17 U14 W10 B9 M3 L3 U11 D1 E2 F2 G4 F1 G3 H3 H1 D2 E4 T2 J3 K1 M4 N2 P2 R1 R2 P4 U3 V2 W1 W2 A17 C9 D5 A3 B4 C5 A4 C8 B8 A8 D9 C10 A18 D16 C17 B17 A19 B19 B20 D18 C20 E18 E19 G17 G18 G19 H18 H20 J18 K19 R20 R19 U18 U19 B5 C4 B3 B2 JL5005 TRST
6.3V
JL5006 VCC
VSS3
VSS2
VSS1
VSS_PLL3
VSS_PLL2
VSS_PLL1
VSSA
CS-
RAS-
CAS-
WE-
DQM3
DQM2
DQM1
DQM0
BA1
BA0
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
CKE
CLKD
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
TCK
TMS
TDI
TDO
C5003
10u B C5030 JL5007 GND
6.3V 0.1u
C5004 B 10V
4.7u B
6.3V
V5 W5 W6 Y6 V7 W7 Y7 V8 W8 V12 U12 Y13 W13 V13 Y14 U16 C19 E17 D19 D20 F18 E20 A2
VSS4 TRST
VSS5 SCLK
are used for IC5002. It is included
VSS6
in TK-071 complete board though
SI
neither of these are supplied.
VSS7 SD
VSS8 SWE-
VSS9 SCS-
VSS10 SRESET- 0 0.8
SO
8
B VSS11 XPD15 0
SI
GND
B
7
VSS12 SCK
XPD14 3.2 VCC 3.2
6
VSS13 xRESET
XPD13 3.2 xWP 0
5
VSS14 xCS
XPD12
VSS15 XPD11 IC5002 (Note) EEPROM
AT45DB081B-CNU
VSS16 XPD10 AT45DB081D-SU
VSS17 XPD9 C5032
VSS18 B
XPO8 0.1u 10V
VSS19 XPD7
VSS20 XPD6
VSS21 XPD5
VSS22 XPD4 X5001
R5046 27MHz
VSS23 XPD3 100 FB5005
C 3 4 C
VSS24 XPD2 2 1
C5031 C5034
0.001u
VSS25 XPD1 0.1u 0.1u
C5033
B B
VSS26 XPD0 10V 10V
AV2_DATA5
AV2_DATA4
AV2_DATA3
AV2_DATA2
AV2_DATA1
AV2_DATA0
AV1_DATA7
AV1_DATA6
AV1_DATA5
AV1_DATA4
AV1_DATA3
AV1_DATA2
AV1_DATA1
AV1_DATA0
AV3_DATA0
AV3_DATA1
AV3_DATA2
AV3_DATA3
AV3_DATA4
AV3_DATA5
AV3_DATA6
AV3_DATA7
AV2_VALID
AV1_VALID
AV3_VALID
AV4_VALID
AV3_DREQ
AV4_DATA
M3.3VA
AV2_SOP
AV1_SOP
AV3_SOP
AV4_SOP
AV2_SOF
AV2_CLK
AV1_SOF
AV1_CLK
AV3_CLK
AV3_SOF
AV4_CLK
AV4_SOF
AV3_IRC
G G
DIOW-
DD15
DD14
DD13
DD12
DD11
DD10
DD0
DD6
DD5
DD4
DD3
DD2
DD1
DD9
DD8
DD7
LD7
LD6
LD5
LD4
LD3
LD2
LD1
LD0
B16 A16 C16 B13 C13 A14 B14 C14 A15 B15 D14 C15 L19 L18 M20 K20 K18 J20 J19 J17 H19 G20 F20 L20 T3 P3 N3 N1 K3 K2 J1 J2 J4 U1 T4 U2 H2 R3 W3 Y3 W4 V4 U5 B11 C11 A11 A10 A7 B7 A6 C7 V15 Y17 W17 V20 T18 T20 P20 N19 M18 N18 P19 T19 U20 T17 V16 W16 V14
#DIOW
4700
4700
4700
4700
XX
LD[7]
LD[6]
LD[5]
LD[4]
LD[3]
LD[2]
LD[1]
LD[0]
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
DD[15]
DD[14]
DD[13]
DD[12]
DD[11]
DD[10]
DD[2]
DD[9]
DD[8]
DD[7]
DD[6]
DD[5]
DD[4]
DD[3]
DD[1]
DD[0]
R5018
R5019
R5020
R5021
R5023
R5001
R5002
R5003
R5004
R5005
R5006
R5007
R5008
R5009
R5010
R5011
R5012
R5013
R5014
R5015
R5016
R5017
R5025
R5026
CL5002
CL5003
CL5004
CL5005
CL5006
CL5007
CL5008
CL5009
CL5010
CL5011
CL5012
CL5013
CL5014
CL5015
CL5016
CL5017
CL5018
CL5019
H NO MARK:REC/PB MODE
H
LD[7]
LD[6]
LD[5]
LD[4]
LD[3]
LD[2]
LD[1]
LD[0]
DD[15]
DD[14]
DD[13]
DD[12]
DD[11]
DD[10]
DD[9]
DD[8]
DD[7]
DD[6]
DD[5]
DD[4]
DD[3]
DD[2]
DD[1]
DD[0]
05
HVR-MRC1
4-5 TK-071 (2/5)
A A
M3.3V
DA[0]
E2 D3 D2 B1 C2 A1 C3 A2 A8 C7 A9 C8 B9 D8 D7 E8 R2 N3 R1 N2 P1 M2 M3 L2 L8 M7 M8 P9 N8 R9 N7 R8 H8 J7 G7 J3 H2 H1 G3 G2 G1 F3 F7 G9 G8
K9 K1 F8 F2 J8 K8 J9 K7 J2 J1 E3 E7 H3 H7 H9 K2 K3 A7 F9 L7 R7 B2 B7 C9 D9 E1 L1 M9 N9 P2 P7 A3 F1 L3 R3 B3 B8 C1 D1 E9 L9 M1 N1 P3 P8
DA[0] A0 VSSQ
DA[1]
DA[1] A1 VSSQ
DA[2]
DA[2] A2 VSSQ
B DA[3]
DA[3]
A3 VSSQ B
DA[4]
DA[4] A4 VSSQ FB3001
DA[5]
DA[5] A5 VSSQ
DA[6]
DA[6] A6 VSSQ
M3.3V
DA[7]
DA[7] A7 VSSQ
DA[8] C3001
DA[8] A8 VSSQ 4.7u
DA[9] 6.3V
DA[9] A9 VSSQ
DA[10] B
DA[10] A10 VSS
DQM0
DQM1
DQM2
DQM3
#CS
#WE
F #RAS
R3001
33
F
R3002
#CAS
33
CLKE CL3003
CLKD
DA[12]
DA[11]
G G
H
TK-071 BOARD (3/5) H
SDRAM
05
HVR-MRC1
4-6 TK-071 (3/5)
FB2001
S3.3V LCD_RESET
LCD_CS1
LCD_A0
R2001
R2002
R2003
R2004
R2005
R2006
R2008
R2009
R2010
R2053
A LCD_SDA A
LCD_SCL
33k 33k 33k 33k 33k 33k 33k 33k 33k 33k
CN2001 20P CN2002 14P
10V 10V
C2004 C2006
B B
GND 20 0.1u 0.1u 14 GND
R2034 SCL
GND 19 13 SCL
3300
3.3V 18 12 GND
R2035
SDA
GND 17 11 SDA
3300
LED_ON 16 10 GND
R2036 A0
R2011
SW_PWR 15 9 A0
1k 3300
GND 14 8 GND
R2012 R2037 #CS_CN
SW_OFF_CN 13 7 CS
1k 3300
R2013
REC_ON 12 6 GND
1k
R2014 R2038 #RES
B STOP 11 1k 5 RES B
3300
GND 10 4 GND
R2015 R2039 ENA
REW 9 3 ENA
1k XX
R2016
PLAY 8 2 GND
1k PWR_LCD
R2017
FF 7 3.0V 1 3.0V
1k
GND 6 CNA
R2018
CAM_LINK 5
R2019
1k CF-110
MENU 4 CN8004
1k Through the
R2020
REPEAT 3 Flexible Flat Cable
1k
(FFC-159)
GND 2 COVER_STAT
(Page 4-9)
GND 1 SW_OFF
B
R2007
R2040
R2041
R2043
R2044
R2046
R2049
220k
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
33k
33k
33k
33k
33k
33k
C SW-525 C
CN7001 25V 25V 25V 25V
25V 25V 25V 25V 25V 25V 25V
Through the
Flexible Flat Cable
C2003
C2005
C2001
C2002
C2007
C2008
C2009
C2010
C2011
C2012
C2013
(FFC-157)
(Page 4-11)
GND
IC2003
10k
10k
R2032
R2028
TC7S32FU(TE85R) R2042
33k
RESET 33k
R2027
SWITCH
3.3
3.2
1
C2017 0 R2048
2
0.1u R2033 3.3 0
3
10V B
1k
D D
CL2026
R2045
1u 10V
C2018 0.1u
4.7u B
B
R0/P3.3
6.3V B
R2021
R2022
3.3
2.5
3.3
3.3
3.3
3.3
3.3
3300
3300
48 47 46 45 44 43 42 41 40 39 38 37
VDD
VSS
REGC
P121/X1/OCD0A
P122/X2/EXCLK/OCD0B
FLMOD
P123/XT1
P124/XT2/EXCLKS
RESET
P40
P41
P120/INTP0/EXLVI
3.2 0 R2050
R2047
25 26 27 28 29 30 31 32 33 34 35 36
PWR_MAIN_33
3.2 3.3 XX SUB_S_RESET
I2C_SDA P61/SDA0 P00/TI000
2
XX
0 3.3
P62/EXSCL0 P01/TI010/TO00
3
SUB_TO_PHY
E CL2004
1.3 3.3 E
P63 P130
4
IB_ENABLE
0 IC2001 3.3
CARD_DETECT P33/TI51/TO51/INTP4 P20/ANI0
5
PWR_SUB_33
1.8 0
PWR_P33 P75 P21/ANI1 PWR_BATT
6
3.3 1 XX
P72/KR2 P24/ANI4
9
3.3 1 CL2041
12 11 10
P71/KR1 P25/ANI5
3.3 0.7 CL2042
XX
XX
0 2
R2056
P32/INTP3/OCD1B
P27/ANI7
P31/INTP2/OCD1A
DCIN_AD
P10/xSCK1/TxDO
P16/TOH1/INTP5
CL2012
P11/SI10/RxD0
P17/TI50/TO50
C2019 C2020
P30/INTP1
XX XX
P15/TOH0
P14/RxD6
P12/SO10
P13/TxD6
AVREF
AVSS
F F
IC2004 13 14 15 16 17 18 19 20 21 22 23 24
IC2005 TC7S32FU(TE85R)
R2062 R2061 XX POWER SWITCH JL2001 VCC
R2059
XX XX
XX
R1/P0.6
R1/P0.5
R0/P3.2
3.2
3.2
3.2
1
0 JL2003 CLK
2
0 JL2004 RXD
3
R2065
XX
XX
G R2064 R2023 XX G
MRESET MRESET_R
0
CF_NDASP
SLEEP
MAIN_TO_SUB
LCD_SDA
05
HVR-MRC1
4-7 TK-071 (4/5)
1 2 3 4 5 6 7 8 9 10 11 12
IC1002
3.3V REG S-812C33BPI-C4NTFG
S3.3V
B+ SWITCH 8 ON/OFF FB1006
1
Q1012 NC
RTQ035P02TR 8 8
VIN
2
D1003
A FB1001 F1001 (1.4A/32V) RSX101VA-30TR 6 8
FB1002 VIN B A
8 3.3 C1045
VSS
4
5
3
ACV_UNREG 2 0.1u
VOUT
1 SPWR
C1004
0.01u R1033 R1034
C1012
B 10u 270k 1M C1042
3
R1005 R1009 0 C1034
10V C 1u
C1005 56k 3600 D1004 0.1u B
0.01u R1012 RSX101VA-30TR 10V 10V
Q1007 B
B
LSK3541FS8T2L
DC IN DETECT 270k
0 0 IC1003 3.0V
2.3
SW_OFF TK11130CSCL-G
DCIN_AD 2.8 Q1011 3V REG FB1007
C1014 R1006 R1010 3.3 3
D1005 DTC115EETL
0.1u 18k 1800
MAZS120008SO 10V INVERTER 0 5 4
Q1008 Q1009
B 3.3 C1035 VIN
GND RTQ035P02TR RTQ035P02TR PWR_SUB_33 R1036 VOUT
CONT
B+ SWITCH 10u 33k C1046
GND
B+ SWITCH Q1013 B
NC
1u
B F1002 (1.4A/32V) 6 6 DTC115EETL
B
R1042 2.3 5 2.7 2.7 5 8 1 2 3
4
4
SET_UNREG 2 2 INVERTER 3.3
0 1 1 PWR_LCD
C1001 10V C1025 10V
C1006
1u 0.01u C1013 Q1003,Q1006 1u
B 2.3 7.2 7.2 B
B 10u
3
BATTERY DETECT
C
C1002 10V C1007 0 C1022 10V R1019
1u 0.01u Q1017 H3.3V
B 0 Q1006
B 1u 1M RTQ035P02TR B+ SWITCH
DTA124EE-TL B
3.3
IB_ENABLE
2.3 6 FB1008
Q1003 3.3 5 3.3
4
2
DTC144EMT2L R1007 Q1010 1
120k DTC115TMT2L 7.2
R1011 DC IN DETECT C1036
R1037
PWR_BATT 10u 33k
0 C1047
3
BATT_AD 0 B
XX 1u
B 10V
C1015 R1008
D1006
0.1u 51k
C MAZS120008SO PWR_CF C
Q1018 M3.3V
RTQ035P02TR B+ SWITCH
6 FB1009
3.3 5 3.3
4
2
1
M3.3VA
C1037
10u 0 C1048
3
B 1u FB1010
R1045
1k
PWR_MAIN_33
R1038 R1041
47k
Q1005 33k
D D
4
FDS6986AS 2.8
SWITCHING
6 S3.3V
3
10k B+ SWITCH
C1016
R1002 6.1
3.3
3.3
0.8
56k C R1029
0 750 0
33k
16 15 14 13 12 11 10 9 C1049
Q1001 R1039 1u
3.3
5.1
6.1
DTC115TMT2L DTC144EMT2L
NC
SW2
TG2
RUN/SS2
SENSE2+
SENSE2-
NC
Vosense2
E NVERTER Q1014 0 E
R1035 1k INVERTER
PWR_P33
1.8
C1039
0.1u B
8.2 0.6
17
BOOST2
8
ITH2
M3.3V
2.8 3.3
18
BG2
7
33VOUT
RESET
19
PGND IC1004
6
SGND
C1009 10V BU4325FVE-TR
IC1001
1u B 5 LTC3728LXCUH#TR-R5 1
GND
20
INTVCC
5
ITH1 3.2
DC R1022 VOUT MRESET
1
R1015 R1017 R1020
C1003 C 0.7 CONTROL 0 3.3
CL1001
21
EXTVCC SUB
4
2
SLEEP FCB
0 XX XX XX
10u 3.3 1.8
CT
3
3.5 0
22
BG1
3
VIN B
2
PLLFLTR
10 B 10V R1016 R1018 R1021
6.8 0.8
24
Vosense1
0.1u XX XX 0
RESET
RUN/SS1
SENSE1+
SENSE1-
PGOOD
IC1005
R1044 BU4325FVE-TR
SW1
TG1
NC
NC
POR-
25 26 27 28 29 30 31 32 33 C1021 C1023 3.3
SUB
2
0.001u 0.001u
6.1 6.1 3.3 1.9
1.8
1.7
2.9
1.5
10V C1011 25V C1017 50V C1019 C1020 R1013 R1014 C1024 1u C1044
100p 5600 10k 100p B 0.1u
Q1002 1000p
D1002 B 0.01u CH50V 50V CH FB1004 A1.8V B
DTC115TMT2L RB520CS-30T2R C
CL1002
INVERTER
2 2.9
G G
R1025 0.051
L1002 FB1005
8 1 1.8
8 7
5 4.7uH 0.051
1.8 6 3 R1026 R1030
20k C1029 C1031 C1032 C1033
C1027 4.7u 10u
Q1004 27p B 6.3V B 4.7u B 4.7u
FDS6986AS 4 3.5 50V CH B
R1031
SWITCHING 16k
R1032
1k
05
HVR-MRC1
4-8 TK-071 (5/5)
A A
8 37 14P CN8003
A10 CL8001 GND(A10)
xVS1 33 36 GND(xVS1)
XX
C xATA_SEL 9
R8015
35 xATA_SEL C
R8016 XX
xIORD 34 34 xIORD
A09 10 33 GND(A09)
R8017 XX
xIORW 35 32 xIORW TK-071
A08 11 31 GND(A08) (1/5)
R8018 XX CN4001
COMPACT xWE 36 30 GND(xWE)
Through the
FLASH FP-201
A07 12 29 GND(A07)
R8019 XX Flexible
INTRQ 37 28 INTRQ (Page 4-4) GND
Vcc 13 27 Vcc
Vcc 38 26 Vcc
A06 14 25 Vcc(A06)
xCSEL 39 24 GND(xCSEL)
A05 15 23 GND(A05)
D CL8002 D
xVS2 40 22 GND(xVS2)
A04 16 21 GND(A04)
R8021 XX
xRESET 41 20 xRESET
A03 17 19 GND(A03)
R8022 XX
IORDY 42 18 IORDY
R8023 XX
A02 18 17 A02
R8024 XX
xINPACK 43 16 xINPACK
R8025 XX
A01 19 15 A01
R8026 XX
xREG 44 14 xREG
R8027 XX
A00 20 13 A00
R8028 XX
xDASP 45 12 xDASP
R8029 XX
D00 21 11 D00
XX
E xPDIAG 46
R8030
10 xPDIAG E
R8031 XX
D01 22 9 D01
R8032 XX
D08 47 8 D08
R8033 XX
D02 23 7 D02
R8034 XX
D09 48 6 D09
CL8003
xIOIS16 24 5 GND(xIOIS16)
R8036 XX
D10 49 4 D10
R8037
xCD2 25 3 GND(xCD2)
XX R8038 XX
GND 50 2 COVER_STAT
1 GND
54
53
52
51
GND
S8001
COVER
F OPEN/CLOSE
F
1 C 2
3 4 C8001
D8001 0.01u
EDZ-TE61-5.6B
G G
H
CF-110 BOARD H
CF CONNECTOR
XX MARK:NO MOUNT
05
HVR-MRC1
4-9 CF-110
A A
CL6030
FB6001
B B
R6007 R6008 R6009 R6010
300k 390 150k 510k
C6012 C6013
10u 0.1u
ND6001 LCD
C B
VSS
1
CN6002 14P
VDD1
2
GND 1
R6011 33k P/S
3
SCL 2
R6012 33k C86
4
GND 3
VSS2
5
SDA 4
R6013 33k CLS
6
GND 5
Q6002 R6014 33k M/S
7
C CF-110 A0 6
R6001
RTF015P02TL
R6003
D6001
CL-271TLY-C-TS C
CN8003 R6004 VDD2
8
3 3
Through the GND 7
XX XX 470 VR
9
Flexible Flat Cable D6001, D6002
CS 8 CL-271TLY-C-TS C6003 16V
(FFC-159) (BACKLIGHT)
49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
R6024 D6002 1u C V5
(Page 4-9) GND 9 0 R6005
33k C6002 C6004 10V
0.1u B V4
RES 10 0 1u 470
C6005 10V
DTC144EMT2L 0.1u B V3
GND 11 Q6001 Q6001, Q6002 C6006
ENA LED DRIVE 0.1u V2
ENA 12 B
C6007
C6001 3.3 V1
GND 13 0.1u B
0.1u B VDD3
3.0V 14
VSS3
C6008
1u C2+
C
C2-
C1+
C6009
D 1u C
C1- D
C6010
C3-
1u C
VOUT
C6011
VSS4
1u C
VSS5
VDD4
SDA
D7
SCL
D6
R6015 33k D5
R6016 33k D4
R6017 33k D3
R6018 33k D2
R6019 33k D1
E E
R6020 33k D0
VDD5
R6021 33k RD
R6022 33k WR
VSS6
A0
A0
#RES
RES
VDD6
R6023 33k CS2
#CS
CS1
VSS7
CL6001 DOF
F CL6002 CL F
CL6003 FR
CL6004 FRS
CL6005 OSC2
CL6006 OSC1
G G
H LC-095 BOARD H
LCD
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
05
HVR-MRC1
4-10 LC-095
A A
C7004
C7007
B 2 4 2 4 2 4 B
D7001
S7001
EDZ-TE61-5.6B
EDZ-TE61-5.6B
EDZ-TE61-5.6B
S7004
C7001
S7007
0.01u
0.01u
0.01u
D7007
D7004
1 3 1 3 1 3
B
B
25V
25V
25V
CAM LINK MENU REPEAT
C7008
C7005
C 2 4 2 4 2 4 C
D7002
S7008
S7002
EDZ-TE61-5.6B
EDZ-TE61-5.6B
EDZ-TE61-5.6B
S7005
C7002
0.01u
0.01u
0.01u
D7008
D7005
1 3 1 3 1 3
B
B
25V
25V
25V
. H >
PLAY
,
,
EXEC
CN7001 20P
20 GND
19 GND
18 REPEAT
C7006
17 MENU
D 2 4 2 4 2 4 D
D7003
S7006
S7003
EDZ-TE61-5.6B
EDZ-TE61-5.6B
16 CAM_LINK
C7003
S7009
0.01u
0.01u
D7006
15 GND
1 3 1 3 1 3
B
B
25V
25V
14 FF
TK-071
13 PLAY (4/5)
12 REW CN2001
s
z Through the
11 GND Flexible Flat Cable
STOP
REC STOP (FFC-157)
10
(Page 4-7)
9 REC_ON
8 SW_OFF_CN
7 GND
6 SW_PWR
5 LED_ON
E 4 GND E
3 3.3V
D7011
XX
R7001 2 GND
S7010
330 R0/P3.3
1 GND
43 2 1 D7009
7 5
R3.3/P0
8 6 CL-196HR-CD-T
REC LAMP, Q7001 3.3
CF ACCESS DTA144EMT2L
POWER
LED DRIVE
ON T OFF
F F
G G
SW-525 BOARD
H H
CONTROL SWITCH
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
R:REC MODE
P:PB MODE
05
HVR-MRC1
4-11 SW-525
A A A A
Note: CN902 (HOT SHOE) is not included in FP-202 flexible board. Note: CN903 (HOT SHOE) is not included in FP-203 flexible board.
D D D D
E E E E
F
FP-202 FLEXIBLE BOARD F F
FP-203 FLEXIBLE BOARD F
HOT SHOE (MEMORY RECORDING UNIT) HOT SHOE (i.LINK CRADLE)
(PRINTED WIRING BOARD is omitted) (PRINTED WIRING BOARD is omitted)
05 05
HVR-MRC1
4-12 FP-202, FP-203
1 2 3 4 5 6 7 8 9 10 11 12
FP-203
FLEXIBLE
LND001 – LND020
(Page 4-12)
A A
ACV_UNREG
ACV_UNREG
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
20P
DETECT
UNREG
UNREG
TPA+
TPB+
TPA-
TPB-
N.C
N.C
Note: BT901 and J901 are not included
CN9005
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
6
8
9
BT901
BATTERY
B TERMINAL
CN9001 4P FB9001 F9001 (1.4A/32V) B
+ BATT(+) 1
SW 2 CL9001
C9003
S SIG 3 CL9002 0.01u
B D9001 LD9002
− MAZS120008SO
BATT(-) 4 R9002
C9004 CHASSIS_GND
0.01u 0
B
CN9004
TH9001
RB9001 6 TPA+
0 TH9002
1 2
7
3 4 5 TPA-
5 6 TH9003
2
7 8 4 TPB+
TH9004 HDV/DV
3 TPB-
1
5
C C
2 VG
8
J901
1 VP
DC IN
CN9002 3P LF9001 F9002 (1.4A/32V)
2 1
PLUS 1
3 4
MINUS_A 2 C9001 10V C9005 R9003
MINUS_B 3 0.01u LD9001
1u B B D9002 0
MAZS120008SO CHASSIS_GND
C9002 10V C9006
0.01u
1u B B
C9007
XX
D D
E E
F F
G G
H
CR-090 BOARD H
DC IN, HDV/DV CONNECTOR
XX MARK:NO MOUNT
05
HVR-MRC1
4-13 CR-090
Link
LC-095 BOARD
HVR-MRC1
(JAPANESE) 4 1
プリント図共通ノート
【プリント図ノート】
・ :無鉛半田を使用しています。
・ :基板
:フレキシブル配線板
見ている面側のパターン。
:裏側のパターン
(他のパターンについては表示されていません)
・スルーホールは省略。
・プリント図には,本機で使用していない部品が記載されている
場合があります。
・Cはパネル表示名称。
HVR-MRC1
4-14
Downloaded from www.Manualslib.com manuals search engine
TK-071 (6 layers)
: Uses unleaded solder.
C1005
R1013
R1020
R1017
R1015
R1014
C1021
R1022
R1032
R1021
R1018
R1016
C1023
C1024
C1020
R1029
C1004
C1001
R1031
F1001 C1019
C1018 33
IC1001
C1006
FB1001
R4069 C1017
C1016
C1013
D1005
R1043
R1044
16 25
CL1002
C1007
FB1002
20 CN4002 1 R1010 17 24
E
4 1
Q1002
G
Q1007
C
1
6
K D1001 A A D1002 K C1011
D
C1010
B
R1003
CL1001
Q1012
C1003
Q1005 C1008
R1001
E
C1009
Q1001
1
5
R1011
C1012
R4070
C
D001
R1004
B
R1002
R4071
R1023
1
5
C1028
5 8
E
LF4001
Q1011
L1001
3
4
R1009
R1033
R1034
B
FB1003
R1024
R4062
C1037
A
4
8
C1034
R4063
C1030 R1045
C1035
FB1007
E
C1046
R4068 R4065
Q1013
R1005
D1003
C1022
C4018
R4073
R4072
3
6 4 D
C4016
R4067 R4064
B
IC1002 2 FL4003 1 C4017
6 4
1 3
1
Q1018 4
R1006
C1014
FB4006
R1012
R4066
Q1015
C4019
KK
1 3
5 4
Q1009
C4007
2
C1031 IC1003
FL4002
R1025
R4049
8 5
Q1010
1 2 3
3
4
C1042
C4005
5 4 G S R4051
C
5
C1025
FL4001 2
IC4002
D1004
FB1009
3
4
1 3 L1002
1
48 33
C4014
E
R1038 R1039 C1049
C1048
3
R1026
Q1004
C4015
C
R4043
R4046
C1029
1
C1045
49 32
1
R1036
FB4002
R1040
C5032
Q1014
A
R1019 FB1010 R4061
C4013
R4044
Q1008
C4012
C1032 FB1006 B E
R5015
R5011
R5013
R5010
R5006
R5008
FB1004
C1039 G
FB4005 65 R4060
Q1016
D1006 C4010
4
FB1005 C1033 D FB4003
8
R5016
R5014
R5012
R5009
R5017
R5007
C5018
2
4
C E
E
C5013 R4059
Q1003
Q1006
C
R4057
JL5011 JL5010 JL5009 JL5008
X4001
R4058
5
1
R4042 R4048
IC1004
C1043
C1040
R4056
1
6 4
R4052
R1008
C1015
3
1
R1007
4
3
A20 B20 C20 D20 E20 F20 G20 H20 J20 K20 L20 M20 N20 P20 R20 T20 U20 V20 W20Y20 1
Q1017
3
C4008
64 17
R5038 R4053
5
IC1005
C1044
C1041
R5036 A19 B19 C19 D19 E19 F19 G19 H19 J19 K19 L19 M19 N19 P19 R19 T19 U19 V19 W19Y19 R2040 R2039
1 16 R4054
FB4004
R5022
C4009
R5034
CN2002
C1047 R1037
R2041
R2038
R4055
A18 B18 C18 D18 E18 F18 G18 H18 J18 K18 L18 M18 N18 P18 R18 T18 U18 V18 W18Y18
CL4004
R2043 R4047
R5002
FB5001
C5002
C4006
A17 B17 C17 D17 E17 F17 G17 H17 J17 K17 L17 M17 N17 P17 R17 T17 U17 V17 W17Y17
C5001
C5022
C5023
R2037
R2044 C5008
R5001 R4050
C5020
R2046 C5007
R5003 A16 B16 C16 D16 U16 V16 W16Y16
14
R2036
CL5005
A14 B14 C14 D14 U14 V14 W14Y14
R1 P1 N1 M1 L1 K1 J1 H1 G1 F1 E1 D1 C1 B1 A1
R2 P2 N2 M2 L2 K2 J2 H2 G2 F2 E2 D2 C2 B2 A2
R3 P3 N3 M3 L3 K3 J3 H3 G3 F3 E3 D3 C3 B3 A3
R7 P7 N7 M7 L7 K7 J7 H7 G7 F7 E7 D7 C7 B7 A7
R8 P8 N8 M8 L8 K8 J8 H8 G8 F8 E8 D8 C8 B8 A8
R9 P9 N9 M9 L9 K9 J9 H9 G9 F9 E9 D9 C9 B9 A9
R5004 R2035
FB5006
CL5002 A1.8V
C3008
C3010
A13 B13 C13 D13 U13 V13 W13Y13
C5019
FB5004
C5003
R4002 R4003
C3007
C5004
C5024
A12 B12 C12 D12 J12 K12 L12 M12 U12 V12 W12Y12
CL5043
C3013
C5005
CL5001
R4004 R4005
FB5003
R4006 R4007
A11 B11 C11 D11 J11 K11 L11 M11 U11 V11 W11Y11
2
R5027
C5025
FB5002
C3014
IC5001 R4008 R4009
M_3.3V
A10 B10 C10 D10 J10 K10 L10 M10 U10 V10 W10Y10
IC3001
R4010 R4011
C5026
A9 B9 C9 D9 J9 K9 L9 M9 U9 V9 W9 Y9 M3.3VA
C5010
R4034
JL5006 JL5007
CL3003
C5030
R5028
A7 B7 C7 D7 U7 V7 W7 Y7
C3005
R4018
C3006
R4016
R5040
M3.3V
FB4001
C5006 C3001
R5041
A6 B6 C6 D6 U6 V6 W6 Y6 C3004
C4003
CN4001
C4002
A5 B5 C5 D5 U5 V5 W5 Y5 C3012
FB3001
R5039
JL5005
C5014
CL5019
R3002
C5016 A2 B2 C2 D2 E2 F2 G2 H2 J2 K2 L2 M2 N2 P2 R2 T2 U2 V2 W2 Y2 R4026 R4023 R4039
C5012
C5009
R3001
CL5016
CL5017
CL5018
R4031 R4032
51
C5021
CL5011 CL5010
CL5013
X5001
CL5014
4 3
FB5005 R5035 R4001
R5032
R5033
R5030
R5029
R5031
2
R5025
R5023
R5021
R5020
1
1
C5033
C5029
C5027
R5018
R5019
R2022
R2021
3 IC2004 1
5
R2048
JL2001
CL2012
R2056
R2055
JL2008
JL2002
JL2003
JL2006
R2032 3 1
IC2003 CL2004
R2003 R2018 C2005 C2001 4 5
R2042
R2045
JL2005
JL2004
C2017
12 1 CL2026 R2033
R2004 R2017 C2007 R2053
R2058 R2057
13 48 C2016 C2022
R2007
C2008
R2064
R2063
R2061
C2009 IC2001
R2031 3IC2005 1
R2006 R2015 4 5
R2028 R2065
R2008 R2014
C2010
24 37 1-874-877- 11 R2059
C2024
C2011
05
20
CN2001
R2009 R2013
25 36
C2012
R2012
CL2041
C2013
C2004
C2006
R2011
R2050
C2020
C2019
CL2042 R2023
R2010
05
1-874-877- 11
HVR-MRC1
4-15 TK-071
14 1
4 2 COVER
S8001
3 1 OPEN/CLOSE
D8001
C8001
51
53
CN8004
1
14
26
2
1
R8001
R8002
R8003
R8004
R8005
R8006
R8007
CN8002
R8008
R8009
51
R8010
50
R8011
R8012
R8013
CL8001
R8015
COMPACT
CN8001
R8016
R8017 FLASH
R8018
R8019
CL8002
R8021
R8022
R8023
R8024
R8025
R8026
R8027
R8028
R8029
R8030
R8031
R8032
2
R8033
1
R8034
CL8003
R8036
R8037
R8038
50 49
25
54
52
1-874-878- 11
HVR-MRC1
4-16 CF-110
SW-525 BOARD
3 3 3 1
1 1
4 2 4 2 4 2
H
> >
PLAY
,
EXEC
3 1 3 1 3
1
S7002 S7005 S7008
4 2 4 2 4 2
LC-095
BOARD C7002 C7005 C7008
(SIDE A)
D7002 D7005 D7008
REC
s
STOP z
3 1 3 3 1
1
ND6001 4 2 4 2 4 2
LCD
C7003
D7003 C7006
A
1 49
D7009
D7011
CF ACCESS E B
K
A K Q7001
D6001, D6002 5 1 4 7
C
R7001
(BACKLIGHT) S7010
05 6 8
A
D6002
20
K
POWER
OFF T ON
CN7001
05 1-874-879- 11
1
1-874-880- 11
CL6030
1 CN6002 14 E B
FB6001
C6001
Q6001
C6012 C
G
Q6002
R6024
C6013 R6001 S
R6005
C6002
R6003 R6004
R6023
CL6002 CL6004 CL6006
R6022
R6020
R6019
C6011
C6008
C6009
C6010
R6018
R6017
R6016
R6009
R6011
R6012
R6013
R6014
R6008
C6004
C6005
C6006
C6007
R6015
R6010
R6007
C6003
05 1-874-879- 11
HVR-MRC1
4-17 LC-095, SW-525
1 2
3 4
TH9004
TH9003
5 6
8 9
CN9004
LD9001
C9007
TH9001
R9002
R9003
LD9002
20 CN9005 1
2 8
RB9001
1 7
HDV/DV
C9005 C9006
D9002 F9002
D9001
F9001
C9003 C9004
1 4
LF9001
FB9001
2 3
C9001 C9002
CL9001 CL9002
1 4 1 3
CN9002
CN9001
05 1-874-881- 11 1-874-881-
05 11
HVR-MRC1
4-18E CR-090
A B C
HVR-MRC1
(ENGLISH)
NOTE: When indicating parts by reference number,
• -XX, -X mean standardized parts, so they may have some differences from please include the board name.
the original one.
• Items marked “*” are not stocked since they are seldom required for routine The components identified by mark 0 or
service. Some delay should be anticipated when ordering these items. dotted line with mark 0 are critical for safety.
• The mechanical parts with no reference number in the exploded views are not Replace only with part number specified.
supplied. Les composants identifiés par une marque
• Due to standardization, replacements in the parts list may be different from 0 sont critiques pour la sécurité.
the parts specified in the diagrams or the components used on the set. Ne les remplacer que par une pièce portant
• CAPACITORS: le numéro spécifié.
uF: µF
• COILS • Color Indication of Appearance Parts
uH: µH Example:
• RESISTORS (SILVER) : Cabinet’s Color
All resistors are in ohms. (Silver) : Parts Color
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
(JAPANESE)
【使用上の注意】 お願い
• ここに記載されている部品は, 補修用部品であるため, 回路図及び 図面番号で部品を指定するときは基板名又はブロック
セットに付いている部品と異なる場合があります。 を併せて指定してください。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。 0印の部品,または0印付の点線で囲まれた部品は,
• コンデンサの単位でuFはμFを示します。 安全性を維持するために,重要な部品です。
• 抵抗の単位Ωは省略してあります。 従って交換時は,必ず指定の部品を使用してください。
金 被:金属被膜抵抗。
サンキン:酸化金属被膜抵抗。 • 外装部品色表示
• インダクタの単位でuHはμHを示します。 例:
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ (SILVER):セットの色を表す。
A..., μPA..., μPB..., μPC..., μPD...を示します。 (Silver) : 部品の色を表す。
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HVR-MRC1
5-1
Downloaded from www.Manualslib.com manuals search engine
Ver. 1.2 2009.03
The changed portions from
Ver. 1.1 are shown in blue.
5. REPAIR PARTS LIST
ns
10
#53
9
11 8
(Note)
7
Note: There are differences in the label indication in
each country/area. #46
Use the correct part for the each camera or model.
(See the chart below)
Note: 仕向によりラベル表示に相違があります。
下表を参照してカメラ本体の機種名・仕向に
合った部品を使用してください。
6
Part No.
Main Model Description
HVR-Z7J
HVR-S270J * A-1700-861-A 4
SERVICE (HVR-MRC1 MAIN J) 5
HVR-MRC1K (J)
HVR-Z7U
HVR-S270U * A-1700-862-A
HVR-MRC1K (US, CND) SERVICE (HVR-MRC1 MAIN U)
HVR-Z7N * A-1700-863-A
HVR-S270N SERVICE (HVR-MRC1 MAIN N)
HVR-Z7P 2 3
HVR-S270P * A-1700-864-A
HVR-Z7E SERVICE (HVR-MRC1 MAIN EP)
HVR-S270E
* A-1700-865-A
HVR-MRC1K (AEP) SERVICE (HVR-MRC1 MAIN KCE)
HVR-Z7C
HVR-S270C * A-1700-866-A
HVR-MRC1K (CH) SERVICE (HVR-MRC1 MAIN C)
Main Cabinet Section
(See page 5-3)
Ref. No. Part No. Description Ref. No. Part No. Description
* 1 3-295-565-01 LABEL (J), CF CAUTION (J) 8 1-965-667-11 FP-202 FLEXIBLE BOARD
* 1 3-295-566-01 LABEL (U), CF CAUTION (US, CND, AEP, E)
* 1 3-295-567-01 LABEL (CN), CF CAUTION (CH) 9 X-2188-922-1 CABINET ASSY, CF BASE
2 1-965-666-11 FP-201 FLEXIBLE BOARD * 10 3-290-945-01 LABEL, FUSE REPLACEMENT
3 1-835-017-11 FLEXIBLE FLAT CABLE (FFC-159) * 11 (Note) SERVICE (HVR-MRC1 MAIN)
CN902 1-818-891-31 CONNECTOR, EXTERNAL (HOT SHOE)
4 A-1498-040-A TK-071 BOARD, COMPLETE (SERVICE) #46 2-660-401-11 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
5 3-290-970-01 SHEET, RADIATION
6 X-2188-921-1 HEAT SINK ASSY, CF #53 3-080-206-21 SCREW, TAPPING, P2 (Black)
* 7 3-290-971-01 SHEET (FP202)
HVR-MRC1
5-2
Downloaded from www.Manualslib.com manuals search engine
Ver. 1.2 2009.03
The changed portions from
Ver. 1.1 are shown in blue.
5. REPAIR PARTS LIST
57
C
F
-1
10
70
58
59
#11 #11
68 60
A 61
#46
62
55
63
54
53
S
64
W
-5
#11
25
#2 65
71
69
52
ns
51
ns
66
67 A
Ref. No. Part No. Description Ref. No. Part No. Description
51 X-2188-920-1 DOOR ASSY, CF * 63 3-290-928-01 SHEET, CF DIFFUSION
52 X-2188-919-1 LOCK ASSY, DOOR * 64 3-290-926-01 FRAME, CF LCD GROUND
53 A-1490-529-A SW-525 BOARD, COMPLETE 65 3-288-253-01 CABINET, CF MAIN
54 1-835-016-11 FLEXIBLE FLAT CABLE (FFC-157)
55 X-2188-918-1 FRAME ASSY, DOOR 66 3-290-968-01 WINDOW, LCD
67 3-295-564-01 LABEL, CF
56 X-2188-823-1 FRAME ASSY, CF MAIN * 68 2-891-483-01 TAPE, LCD
57 A-1490-526-A CF-110 BOARD, COMPLETE 69 3-296-530-01 SHEET (H)
58 1-835-017-11 FLEXIBLE FLAT CABLE (FFC-159) * 70 3-290-969-01 FRAME (UPPER), CF DOOR GROUND
59 A-1544-473-A LC-095 BOARD, COMPLETE (SERVICE)
60 3-290-930-01 HOLDER, LCD * 71 2-697-881-01 DAMPER, LCD
#2 2-635-562-31 SCREW (M1.7) (Black)
* 61 3-290-929-01 SHEET, CF REFLECTION #11 3-078-890-11 SCREW, TAPPING (Silver)
* 62 3-290-927-01 LIGHT, GUIDE #46 2-660-401-11 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
HVR-MRC1
5-3
Downloaded from www.Manualslib.com manuals search engine
Ver. 1.2 2009.03
The changed portions from
Ver. 1.1 are shown in blue.
5. REPAIR PARTS LIST
111
108 109
BT901
107
J901
106 105
#12 #12
113 #12
114 #12
#12
#1
102
104
101
103
CN903
#1
0 F9001 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V) Q6001 6-550-119-01 TRANSISTOR DTC144EMFS6T2L
0 F9002 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V) Q6002 6-551-067-01 TRANSISTOR RTF015P02TL
* FB9001 1-481-196-21 FERRITE, EMI (SMD) (3216) R6004 1-218-839-11 METAL CHIP 470 0.5% 1/10W
R6005 1-218-839-11 METAL CHIP 470 0.5% 1/10W
< LINE FILTER > R6007 1-208-946-81 METAL CHIP 300K 0.5% 1/16W
R6008 1-218-948-11 RES-CHIP 390 5% 1/16W
* LF9001 1-457-217-21 COMMON MODE CHOKE COIL R6009 1-208-939-11 METAL CHIP 150K 0.5% 1/16W
< RESISTOR > R6010 1-208-952-81 METAL CHIP 510K 0.5% 1/16W
R6011 1-218-971-11 RES-CHIP 33K 5% 1/16W
R9002 1-216-864-11 SHORT CHIP 0 R6012 1-218-971-11 RES-CHIP 33K 5% 1/16W
R9003 1-216-864-11 SHORT CHIP 0 R6013 1-218-971-11 RES-CHIP 33K 5% 1/16W
HVR-MRC1
5-5
Downloaded from www.Manualslib.com manuals search engine
Ver. 1.1 2008.06
The changed portions from LC-095 SW-525 TK-071
Ver. 1.0 are shown in blue.
Ref. No. Part No. Description Ref. No. Part No. Description
R6014 1-218-971-11 RES-CHIP 33K 5% 1/16W S7010 1-771-731-21 SWITCH, SLIDE (POWER (ON/OFF))
< DIODE > C1021 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C1022 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
D7001 8-719-074-67 DIODE EDZ-TE61-5.6B C1023 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
D7002 8-719-074-67 DIODE EDZ-TE61-5.6B C1024 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
D7003 8-719-074-67 DIODE EDZ-TE61-5.6B C1025 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
D7004 8-719-074-67 DIODE EDZ-TE61-5.6B
D7005 8-719-074-67 DIODE EDZ-TE61-5.6B C1026 1-164-860-11 CERAMIC CHIP 27PF 5% 50V
C1027 1-164-860-11 CERAMIC CHIP 27PF 5% 50V
D7006 8-719-074-67 DIODE EDZ-TE61-5.6B * C1028 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
D7007 8-719-074-67 DIODE EDZ-TE61-5.6B * C1029 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
D7008 8-719-074-67 DIODE EDZ-TE61-5.6B C1030 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
D7009 8-719-077-09 DIODE CL-196HR-CD-T
(REC LAMP, CF ACCESS) C1031 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
* C1032 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
< TRANSISTOR > * C1033 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C1034 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
Q7001 6-550-239-01 TRANSISTOR DTA144EMFS6T2L C1035 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
< RESISTOR > C1036 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
C1037 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
R7001 1-208-671-11 METAL CHIP 330 0.5% 1/16W C1038 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C1039 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
< SWITCH > C1040 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
S7001 1-771-844-21 SWITCH, TACTILE (CAM LINK) C1041 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
S7002 1-771-844-21 SWITCH, TACTILE (., EXEC M) C1042 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
S7003 1-771-844-21 SWITCH, TACTILE (s STOP) C1043 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
S7004 1-771-844-21 SWITCH, TACTILE (MENU) C1044 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
S7005 1-771-844-21 SWITCH, TACTILE (H PLAY, EXEC) C1045 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
S7006 1-771-844-21 SWITCH, TACTILE (REC z) C1046 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
S7007 1-771-844-21 SWITCH, TACTILE (REPEAT) C1047 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
S7008 1-771-844-21 SWITCH, TACTILE (>, EXEC m) C1048 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
S7009 1-771-844-21 SWITCH, TACTILE (REC) C1049 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C2001 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
HVR-MRC1
5-6
Downloaded from www.Manualslib.com manuals search engine
Ver. 1.2 2009.03
The changed portions from TK-071
Ver. 1.1 are shown in blue.
Ref. No. Part No. Description Ref. No. Part No. Description
C5008 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2002 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V C5009 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2003 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V C5010 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2004 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2005 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V C5011 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2006 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C5012 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C5013 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2007 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V C5014 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2008 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V C5015 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2009 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C2010 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V C5016 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2011 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V C5017 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C5018 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2012 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V C5019 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2013 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V C5020 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C2016 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C2017 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C5021 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
* C2018 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V C5022 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C5023 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C2022 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C5024 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C2023 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V * C5025 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
* C3001 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C3002 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C5026 1-164-933-11 CERAMIC CHIP 220PF 10% 50V
C3003 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C5028 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C5030 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C3004 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C5031 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C3005 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C5032 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C3006 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C3007 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C5033 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C3008 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C5034 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C3009 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < CONNECTOR >
C3010 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C3011 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V * CN2001 1-818-516-71 CONNECTOR, FFC/FPC (ZIF) 20P
C3012 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V CN2002 1-816-645-61 FFC/FPC CONNECTOR (LIF) 14P
C3013 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V * CN4001 1-820-857-81 CONNECTOR, FPC (ZIF) 51P
CN4002 1-816-648-61 FFC/FPC CONNECTOR (LIF) 20P
C3014 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C3015 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < DIODE >
C4001 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C4002 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V D001 6-500-750-01 DIODE NSAD500H-T1-A
C4003 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V 0 D1001 6-501-272-01 DIODE RB520CS-30T2R
0 D1002 6-501-272-01 DIODE RB520CS-30T2R
C4005 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V D1003 6-501-124-01 DIODE RSX101VA-30TR
* C4006 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V D1004 6-501-124-01 DIODE RSX101VA-30TR
C4007 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C4008 1-164-852-11 CERAMIC CHIP 12PF 5% 50V * D1005 6-501-961-01 DIODE MAZS120G08S0
C4009 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V * D1006 6-501-961-01 DIODE MAZS120G08S0
C4010 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < FUSE >
C4011 1-164-852-11 CERAMIC CHIP 12PF 5% 50V
C4012 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V 0 F1001 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V)
C4013 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V 0 F1002 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V)
C4014 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
< FERRITE BEAD >
C4015 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
* C4016 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V * FB1001 1-481-196-21 FERRITE, EMI (SMD) (3216)
C4017 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V FB1002 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)
C4018 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V FB1003 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)
C4019 1-164-933-11 CERAMIC CHIP 220PF 10% 50V FB1004 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)
FB1005 1-400-619-11 BEAD, FERRITE (CHIP) (1608)
* C5001 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V
C5002 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V FB1006 1-400-619-11 BEAD, FERRITE (CHIP) (1608)
C5003 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V FB1007 1-400-619-11 BEAD, FERRITE (CHIP) (1608)
* C5004 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V FB1008 1-400-619-11 BEAD, FERRITE (CHIP) (1608)
C5005 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V FB1009 1-400-331-11 FERRITE, EMI (SMD) (1005)
FB1010 1-400-619-11 BEAD, FERRITE (CHIP) (1608)
C5006 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C5007 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V FB2001 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)
HVR-MRC1
5-7
Downloaded from www.Manualslib.com manuals search engine
TK-071
Ref. No. Part No. Description Ref. No. Part No. Description
FB3001 1-400-915-21 INDUCTOR (EMI FERRITE) (2012)
FB4001 1-400-915-21 INDUCTOR (EMI FERRITE) (2012) Q1016 6-551-067-01 TRANSISTOR RTF015P02TL
FB4002 1-400-915-21 INDUCTOR (EMI FERRITE) (2012) Q1017 6-550-354-01 TRANSISTOR RTQ035P02TR
FB4003 1-400-331-11 FERRITE, EMI (SMD) (1005) Q1018 6-550-354-01 TRANSISTOR RTQ035P02TR
L1001 1-456-019-11 INDUCTOR 4.7uH R1037 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
L1002 1-456-019-11 INDUCTOR 4.7uH R1038 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
R1039 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
< LINE FILTER > R1040 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R1041 1-208-927-11 METAL CHIP 47K 0.5% 1/16W
LF4001 1-457-064-13 COMMON MODE CHOKE COIL
R1042 1-216-864-11 SHORT CHIP 0
< TRANSISTOR > R1043 1-218-977-11 RES-CHIP 100K 5% 1/16W
R1044 1-218-977-11 RES-CHIP 100K 5% 1/16W
Q1001 6-550-566-01 TRANSISTOR DTC115TMFS6T2L R1045 1-218-953-11 RES-CHIP 1K 5% 1/16W
Q1002 6-550-566-01 TRANSISTOR DTC115TMFS6T2L R2001 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
Q1003 6-550-119-01 TRANSISTOR DTC144EMFS6T2L
0 Q1004 6-709-438-01 TRANSISTOR FDS6986AS R2002 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
0 Q1005 6-709-438-01 TRANSISTOR FDS6986AS R2003 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
R2004 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
Q1006 8-729-928-34 TRANSISTOR DTA124EE-TL R2005 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
Q1007 6-551-346-01 TRANSISTOR LSK3541FS8T2L R2006 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
Q1008 6-550-354-01 TRANSISTOR RTQ035P02TR
Q1009 6-550-354-01 TRANSISTOR RTQ035P02TR R2007 1-208-943-11 METAL CHIP 220K 0.5% 1/16W
Q1010 6-550-566-01 TRANSISTOR DTC115TMFS6T2L
Note: Two interchangeable kinds of IC are used for
IC5002. It is included in TK-071 complete board
* Q1011 6-551-600-01 TRANSISTOR DTC115EETL
though neither of these are supplied.
Q1012 6-550-354-01 TRANSISTOR RTQ035P02TR
* Q1013 6-551-600-01 TRANSISTOR DTC115EETL
Q1014 6-550-119-01 TRANSISTOR DTC144EMFS6T2L Note: IC5002には互換性のある2種類のICが使用され
ています。これらはいずれも供給されません
Q1015 6-551-067-01 TRANSISTOR RTF015P02TL
が,マウント済みTK-071基板に含まれます。
• Refer to page 5-1 for mark 0.
HVR-MRC1
5-8
Downloaded from www.Manualslib.com manuals search engine
TK-071
Ref. No. Part No. Description Ref. No. Part No. Description
R2008 1-208-923-11 METAL CHIP 33K 0.5% 1/16W R4022 1-218-935-11 RES-CHIP 33 5% 1/16W
R2009 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
R2010 1-208-923-11 METAL CHIP 33K 0.5% 1/16W R4023 1-218-933-11 RES-CHIP 22 5% 1/16W
R2011 1-208-683-11 METAL CHIP 1K 0.5% 1/16W R4024 1-218-935-11 RES-CHIP 33 5% 1/16W
R4025 1-218-935-11 RES-CHIP 33 5% 1/16W
R2012 1-208-683-11 METAL CHIP 1K 0.5% 1/16W R4026 1-218-935-11 RES-CHIP 33 5% 1/16W
R2013 1-208-683-11 METAL CHIP 1K 0.5% 1/16W R4028 1-218-935-11 RES-CHIP 33 5% 1/16W
R2014 1-208-683-11 METAL CHIP 1K 0.5% 1/16W
R2015 1-208-683-11 METAL CHIP 1K 0.5% 1/16W R4029 1-218-935-11 RES-CHIP 33 5% 1/16W
R2016 1-208-683-11 METAL CHIP 1K 0.5% 1/16W R4030 1-218-935-11 RES-CHIP 33 5% 1/16W
R4031 1-218-935-11 RES-CHIP 33 5% 1/16W
R2017 1-208-683-11 METAL CHIP 1K 0.5% 1/16W R4032 1-218-935-11 RES-CHIP 33 5% 1/16W
R2018 1-208-683-11 METAL CHIP 1K 0.5% 1/16W R4033 1-218-935-11 RES-CHIP 33 5% 1/16W
R2019 1-208-683-11 METAL CHIP 1K 0.5% 1/16W
R2020 1-208-683-11 METAL CHIP 1K 0.5% 1/16W R4034 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2021 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16W R4035 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R4036 1-218-962-11 RES-CHIP 5.6K 5% 1/16W
R2022 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16W R4037 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2026 1-208-911-11 METAL CHIP 10K 0.5% 1/16W R4038 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R2027 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2028 1-208-911-11 METAL CHIP 10K 0.5% 1/16W R4039 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2032 1-208-923-11 METAL CHIP 33K 0.5% 1/16W R4040 1-218-977-11 RES-CHIP 100K 5% 1/16W
R4042 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
R2033 1-208-683-11 METAL CHIP 1K 0.5% 1/16W R4043 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2034 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16W R4047 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2035 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16W
R2036 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16W R4050 1-208-855-81 METAL CHIP 47 0.5% 1/16W
R2037 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16W R4051 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4055 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R2038 1-208-695-11 METAL CHIP 3.3K 0.5% 1/16W R4056 1-218-990-81 SHORT CHIP 0
R2040 1-208-923-11 METAL CHIP 33K 0.5% 1/16W R4057 1-218-990-81 SHORT CHIP 0
R2041 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
R2042 1-208-923-11 METAL CHIP 33K 0.5% 1/16W R4058 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
R2043 1-208-923-11 METAL CHIP 33K 0.5% 1/16W R4059 1-208-683-11 METAL CHIP 1K 0.5% 1/16W
R4060 1-208-683-11 METAL CHIP 1K 0.5% 1/16W
R2044 1-208-923-11 METAL CHIP 33K 0.5% 1/16W R4061 1-208-683-11 METAL CHIP 1K 0.5% 1/16W
R2045 1-208-911-11 METAL CHIP 10K 0.5% 1/16W R4062 1-208-906-81 METAL CHIP 6.2K 0.5% 1/16W
R2046 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
R2048 1-218-990-81 SHORT CHIP 0 R4063 1-208-663-11 METAL CHIP 150 0.5% 1/16W
R2049 1-208-923-11 METAL CHIP 33K 0.5% 1/16W R4064 1-218-938-11 RES-CHIP 56 5% 1/16W
R4065 1-218-938-11 RES-CHIP 56 5% 1/16W
R2053 1-208-923-11 METAL CHIP 33K 0.5% 1/16W R4066 1-218-864-11 METAL CHIP 5.1K 0.5% 1/10W
R2055 1-208-911-11 METAL CHIP 10K 0.5% 1/16W R4067 1-218-938-11 RES-CHIP 56 5% 1/16W
R2064 1-218-990-81 SHORT CHIP 0
R3001 1-208-647-11 METAL CHIP 33 0.5% 1/16W R4068 1-218-938-11 RES-CHIP 56 5% 1/16W
R3002 1-208-647-11 METAL CHIP 33 0.5% 1/16W R4069 1-216-864-11 SHORT CHIP 0
R4070 1-216-864-11 SHORT CHIP 0
R4001 1-218-935-11 RES-CHIP 33 5% 1/16W R4071 1-216-864-11 SHORT CHIP 0
R4002 1-218-935-11 RES-CHIP 33 5% 1/16W R5018 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R4003 1-218-935-11 RES-CHIP 33 5% 1/16W
R4004 1-218-935-11 RES-CHIP 33 5% 1/16W R5020 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R4005 1-218-935-11 RES-CHIP 33 5% 1/16W R5021 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R5022 1-218-935-11 RES-CHIP 33 5% 1/16W
R4006 1-218-935-11 RES-CHIP 33 5% 1/16W R5023 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R4007 1-218-935-11 RES-CHIP 33 5% 1/16W R5024 1-218-938-11 RES-CHIP 56 5% 1/16W
R4008 1-218-935-11 RES-CHIP 33 5% 1/16W
R4009 1-218-935-11 RES-CHIP 33 5% 1/16W R5027 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R4010 1-218-935-11 RES-CHIP 33 5% 1/16W R5028 1-218-990-81 SHORT CHIP 0
R5034 1-208-923-11 METAL CHIP 33K 0.5% 1/16W
R4011 1-218-935-11 RES-CHIP 33 5% 1/16W R5035 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4012 1-218-935-11 RES-CHIP 33 5% 1/16W R5036 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R4013 1-218-935-11 RES-CHIP 33 5% 1/16W
R4015 1-218-933-11 RES-CHIP 22 5% 1/16W R5037 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R4016 1-218-933-11 RES-CHIP 22 5% 1/16W R5038 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R5039 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R4018 1-208-861-81 METAL CHIP 82 0.5% 1/16W R5040 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R4019 1-208-861-81 METAL CHIP 82 0.5% 1/16W R5041 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
R4020 1-218-935-11 RES-CHIP 33 5% 1/16W
R4021 1-208-861-81 METAL CHIP 82 0.5% 1/16W R5046 1-218-941-81 RES-CHIP 100 5% 1/16W
HVR-MRC1
5-9
Downloaded from www.Manualslib.com manuals search engine
TK-071
Ref. No. Part No. Description Ref. No. Part No. Description
HVR-MRC1
5-10
Downloaded from www.Manualslib.com manuals search engine
• EXCEPT J MODEL
Checking supplied accessories.
CD-ROM (Note)
“Manuals for Digital HD Video Camera Recorder”
• J MODEL
付属品
CD-ROM (Note)
「Manuals for Digital HD Video Camera Recorder」
HVR-MRC1
5-11E
Downloaded from www.Manualslib.com manuals search engine
6. ADJUSTMENTS
• Connection Diagram
(Connecting cord)
(DK-215)
Fig. 6-1-1
Procedures
1) Attach the iLINK cradle (HVRA-CR1) to the set.
2) Connect the set to the PC with the i.LINK cable.
Note: Remove the Compact Flash card if it has been inserted in the set.
3) Slide the POWER switch of this set to ON.
4) Check that the LCD screen of the set changes from “Welcome” to a blinking state of CF icon as shown below.
Icon is blinking
Fig. 6-1-2
HVR-MRC1
6-1
Downloaded from www.Manualslib.com manuals search engine
1-2. List of Service Tools
J-1 J-2 J-3
iLINK cable
(Commercial item)
AC Adaptor/Charger
Personal computer (AC-VQ1050)
(Note 1) 1-479-580-11
• Files used
Folder Name File Name Remarks
Uploader 1394API.dll For installation of exclusive driver
1394DIAG.sys
1394vdev.inf
1394vdev.sys
port95nt.exe
CMD1394.exe
tnf.exe
batch_e HISTORY_E.bat Reading of history information
(English version) ERROR_E.bat Clearing of error code history
POWER_E.bat Clearing of accumulated POWER ON time
REC_E.bat Clearing of accumulated recording time
PB_E.bat Clearing of accumulated playback time
FILE_E.bat Clearing of accumulated files created
CFDET_E.bat Clearing of accumulated CF detection count
batch_j HISTORY.bat Reading of history information
(Japanese version) ERROR.bat Clearing of error code history
POWER.bat Clearing of accumulated POWER ON time
REC.bat Clearing of accumulated recording time
PB.bat Clearing of accumulated playback time
FILE.bat Clearing of accumulated files created
CFDET.bat Clearing of accumulated CF detection count
Note 1: OS: Windows XP HomeEdition (Service Pack2 or later)
Windows XP Professional (Service Pack2 or later)
Standard installation is required.
Operation is not assured if rhe above OS has been upgraded.
CPU: MMX Pentium 200 MHz or faster
IEEE1394 terminal (DV connector)
Note 2: Retrieve the batch file etc. used from the item of “ESI Jig & Software” of “ESI homepage” by the following conditions
Model Name: HVR-MRC1
Category: MPU/ROM/Software
HVR-MRC1
6-2
Downloaded from www.Manualslib.com manuals search engine
1-3. Installation of Driver 6. Select “Add a new hardware device” and click “Next”.
Fig. 6-1-5
Fig. 6-1-3
Fig. 6-1-6
Fig. 6-1-4
Fig. 6-1-7
HVR-MRC1
6-3
Downloaded from www.Manualslib.com manuals search engine
9. Click “Have Disk”. 12. Click “OK”.
Fig. 6-1-11
Fig. 6-1-8
11. Select “1394vdev.inf” copied to the PC and click “Open”. 14. Click “Next”. Then, the installation starts.
HVR-MRC1
6-4
Downloaded from www.Manualslib.com manuals search engine
15. Confirm the result of driver installation. 17. If “Unknown device” is displayed below “1394 Test Devices”,
Open “System Properties” → “Device Manager”. update the driver in the procedures below.
Fig. 6-1-16
Fig. 6-1-14
Fig. 6-1-17
19. Select “Install from a list or specific location” and click “Next”.
Fig. 6-1-15
Fig. 6-1-18
HVR-MRC1
6-5
Downloaded from www.Manualslib.com manuals search engine
20. Click “Browse”. 22. After the installation completes, click “Finish”.
23. Open “Device Manager”. If “1384 Virtual Devices” is displayed
below “1394 Test Devices”, the installation is normally fin-
ished.
Fig. 6-1-19
21. Specify the location (Uploader) where the driver is saved and
click “OK”.
The installation starts. Fig. 6-1-21
Fig. 6-1-20
HVR-MRC1
6-6
Downloaded from www.Manualslib.com manuals search engine
1-4. Reading of History Information 1-5. Clearing of Error Code History
Note: The following shows a case that uses the batch file of En- Note: The following shows a case that uses the batch file of En-
glish version. glish version.
For Japanese version, use “HISTORY.bat”. For Japanese version, use “ERROR.bat”.
Procedures Procedures
1. Double-click “HISTORY_E.bat” copied to the PC. 1. Double-click “ERROR_E.bat” copied to the PC.
2. The command prompt starts up. Following the message, press 2. The command prompt starts up.
the [ENTER] key of PC.
Fig. 6-1-24
Fig. 6-1-22
• To execute, press the [ENTER] key of PC. The clearing of error
3. The Notepad will open automatically and display the history code history will be executed.
information. • To cancel, click “x” mark at the upper right of the command
prompt window to close the command prompt window.
Fig. 6-1-25
HVR-MRC1
6-7
Downloaded from www.Manualslib.com manuals search engine
1-6. Clearing of Accumulated POWER ON Time 1-7. Clearing of Accumulated Recording Time
Note: The following shows a case that uses the batch file of En- Note: The following shows a case that uses the batch file of En-
glish version. glish version.
For Japanese version, use “POWER.bat”. For Japanese version, use “REC.bat”.
Procedures Procedures
1. Double-click “POWER_E.bat” copied to the PC. 1. Double-click “REC_E.bat” copied to the PC.
2. The command prompt starts up. 2. The command prompt starts up.
• To execute, press the [ENTER] key of PC. The clearing of accu- • To execute, press the [ENTER] key of PC. The clearing of accu-
mulated POWER ON time will be executed. mulated recording time will be executed.
• To cancel, click “x” mark at the upper right of the command • To cancel, click “x” mark at the upper right of the command
prompt window to close the command prompt window. prompt window to close the command prompt window.
3. When the clearing of accumulated POWER ON time finished, 3. When the clearing of accumulated recording time finished, the
the following message will be displayed in the command following message will be displayed in the command prompt
prompt window. window.
4. Press the [ENTER] key of PC to close the command prompt 4. Press the [ENTER] key of PC to close the command prompt
window. window.
HVR-MRC1
6-8
Downloaded from www.Manualslib.com manuals search engine
1-8. Clearing of Accumulated Playback Time 1-9. Clearing of Accumulated Files Created
Note: The following shows a case that uses the batch file of En- Note: The following shows a case that uses the batch file of En-
glish version. glish version.
For Japanese version, use “PB.bat”. For Japanese version, use “FILE.bat”.
Procedures Procedures
1. Double-click “PB_E.bat” copied to the PC. 1. Double-click “FILE_E.bat” copied to the PC.
2. The command prompt starts up. 2. The command prompt starts up.
• To execute, press the [ENTER] key of PC. The clearing of accu- • To execute, press the [ENTER] key of PC. The clearing of accu-
mulated playback time will be executed. mulated files created will be executed.
• To cancel, click “x” mark at the upper right of the command • To cancel, click “x” mark at the upper right of the command
prompt window to close the command prompt window. prompt window to close the command prompt window.
3. When the clearing of accumulated playback time finished, the 3. When the clearing of accumulated files created finished, the
following message will be displayed in the command prompt following message will be displayed in the command prompt
window. window.
4. Press the [ENTER] key of PC to close the command prompt 4. Press the [ENTER] key of PC to close the command prompt
window. window.
HVR-MRC1
6-9
Downloaded from www.Manualslib.com manuals search engine
1-10. Clearing of Accumulated CF Detection Count
Note: The following shows a case that uses the batch file of En-
glish version.
For Japanese version, use “CFDET.bat”.
Procedures
1. Double-click “CFDET_E.bat” copied to the PC.
2. The command prompt starts up.
Fig. 6-1-34
Fig. 6-1-35
HVR-MRC1
6-10E
Downloaded from www.Manualslib.com manuals search engine
3-290-149-11(1)
Memory Recording
Unit
Operating Instructions
Owner’s record
The model number and the serial number are located at the name plate on the left of the
unit. Record the serial number in the space provided below. Refer to these numbers
whenever you call upon your Sony dealer regarding this product.
HVR-MRC1
2008 Sony Corporation
Using in VIDEO mode .................................... 6 All other product names mentioned herein may be the
Connecting this unit to a camcorder ................................ 6 trademarks or registered trademarks of their respective
Inserting/removing optional memory media ................ 6 companies. Furthermore, ™ and “®” are not mentioned in
each case in this manual.
Menu settings ...................................................................... 6
Specifications ............................................... 28
Precautions ................................................... 29
Getting the best performance from the
battery pack ................................................. 30
2
Downloaded from www.Manualslib.com manuals search engine
Overview
3
Downloaded from www.Manualslib.com manuals search engine
Names of parts
1
qg
5
6
7 qf
2 qh
8
3 9
q;
4 qj qk
qa
qs
qd
Attaching to the i.LINK cradle
Attach this unit to the i.LINK cradle by sliding
the unit in the direction of the arrow.
4
Downloaded from www.Manualslib.com manuals search engine
LCD screen display
VIDEO mode
1 2 3 4 5 qa
9 6 q;
8 7
5
Downloaded from www.Manualslib.com manuals search engine
Using in VIDEO mode
Inserting/removing optional
memory media
• Although this unit has been tested with CompactFlash, 1
Sony does not guarantee its operation with all 1
CompactFlash.
The operation of this unit with Sony CompactFlash has
been checked.
CompactFlash capacity and available
• CompactFlash with 133x 2GB or more specifications are recording time
recommended for this unit. (A speed of less than 133x is
CompactFlash available recording time
not guaranteed; space less than 2GB is not guaranteed.)
• Always format a new CompactFlash with this unit 2GB Approx. 9 min.
before use.
4GB Approx. 18 min.
• Do not remove the CompactFlash while the access lamp
is blinking. 8GB Approx. 36 min.
16GB Approx. 72 min.
Inserting the CompactFlash
1 Open the CompactFlash slot door while sliding the Notes
OPEN latch.
Do not repeatedly insert or remove the CompactFlash over a
2 Push the CompactFlash in the correct direction until it short amount of time. Doing so may cause mis-recognition of
clicks into place. the CompactFlash and memory malfunction. If you open the
3 Close the CompactFlash slot door. CompactFlash slot door while the unit is recording or in
playback, operations will stop. If that occurs, be sure that the
1 status on the LCD screen changes to x (playback/recording
is stopped) before removing the CompactFlash.
When ejecting the CompactFlash, forcefully pressing the eject
lever and allowing the CompactFlash to be pointed
downward when ejected will cause the CompactFlash to fall.
Menu settings
3
Check the individual settings and change them if necessary.
For details, see page 7.
1 Display the menu screen on the LCD screen by
pressing the MENU button.
2
2 Select the desired setting by pressing the PREVIOUS/
REW button or the NEXT/FF button and press the
PLAY/EXEC button.
3 Select the desired item by pressing the PREVIOUS/REW
button or the NEXT/FF button and press the PLAY/
EXEC button.
4 Return to the VIDEO mode screen by pressing the
STOP button. Press the MENU button to close the
menu screen.
Notes
You cannot record or play back movies while the menu
screen is displayed on the LCD screen. Also, you cannot
change to the menu screen on the LCD screen during
recording or playback.
6
Downloaded from www.Manualslib.com manuals search engine
Menu organization (VIDEO mode)
DELETE Notes
Deletes the recorded data or formats the CompactFlash. When inputting the stream signal from the i.LINK,
• CLIP INTERVAL and LOOP is valid.
Displays the three clip numbers from those displayed on the
normal screen.
Selects and deletes clips. i.LINK MODE
• ALL • AUTO ....... Automatically switches to the camcorder
Deletes all the recorded clips. recording/playback format.
• FORMAT • HDV .......... Plays back HDV format only.
Formats the CompactFlash. • DV ............. Plays back DVCAM (DV) format only.
If there is no clip, you cannot make a selection.
7
Downloaded from www.Manualslib.com manuals search engine
CAMERA NO
SETTING You can assign a number to the data clip name when
recording.
TC FORMAT Use this mode to assign non-overlapping numbers to clip
Follows the DF/NDF of the time code from the camcorder names recorded simultaneously on more than one camcorder,
connected to this unit. or to manage clip data by assigning numbers.
• AUTO ....... Follows the time code format of the camcorder. Press the PREVIOUS/REW (previous clip/rewind) or NEXT/
• NDF ........... Records the time code in NDF format. FF (next clip/fast-forward) button to select the number and
• DF .............. Records the time code in DF format. press the PLAY/EXEC (playback/execute) button.
Notes Select the digits one by one. The display returns to the menu
after two digits are selected.
The default [AUTO] setting is NDF. If time code information The factory default setting is [00].
from the camcorder is not obtained, this unit is set to the most
recent recording setting.
ALL RESET
DV FILE TYPE
Restores all default settings.
Changes the DV recording format.
• AVI ............ Records video in AVI format.
• RAW DV ... Records video in DV format.
INTERVAL
• REC TIME
Selects the interval recording time.
You can select [0.5sec], [1sec], [1.5sec] or [2sec].
• INT.TIME
Selects the interval time between recordings.
You can select [30 sec], [1 min], [5 min], or [10 min].
SLEEP MODE
Switches the sleep mode ON/OFF.
• OFF
Sleep mode is set to OFF.
• 1min
If the i.LINK cable is disconnected and no operation is done
for more than one minute, this unit automatically switches to
SLEEP status.
• 5min
If the i.LINK cable is disconnected and no operation is done
for more than five minutes, this unit automatically switches
to SLEEP status.
To return to normal status, reconnect the i.LINK cable to this
unit or turn the POWER switch off and back on.
Notes
In SLEEP MODE, this unit is not completely switched off but
continues to run using low power consumption.
8
Downloaded from www.Manualslib.com manuals search engine
Recording images from the camcorder to this unit
Images recorded by the camcorder can be recorded onto this x Recording video simultaneously on this unit and
unit. a camcorder
– Connecting to a camcorder with an “external REC
control” function (SYNCHRO mode)
Recording images When connected to a camcorder that has an external REC
(POWER switch at the ON side) control function, this unit can be controlled by the
camcorder to record video data simultaneously to the
The different methods of recording are as follows: camcorder recording on tape.
• Clips recorded by this unit include several frames after
x Recording video simultaneously on this unit and the recording stopping point on the tape.
a camcorder
x Recording on this unit during camcorder tape Camcorder STANDBY REC STANDBY
x Recording video from this unit This unit STANDBY REC STANDBY
x Operating cache recording
x Operating interval recording 1 Press the CAM LINK button of this unit and set it to
x Operating loop recording ON.
2 Set the [CAM LINK SEL] setting of this unit to
[SYNCHRO].
3 Set the [EXT REC CTRL] setting of the camcorder to
[SYNCHRONOUS].
4 Connect the camcorder to this unit via an i.LINK cable.
Notes
5 Press the REC START/STOP button of the camcorder to
• A 0 KB file may be created, but the file cannot be opened start recording.
because it does not have video data. Do not delete the 0 KB • The above Step 3 is for the HVR-Z7/S270 series. For details
file on your computer. If you do, this clip cannot be played on another camcorder you want to connect to this unit,
back. refer to the operating instructions supplied with that
• When changing the tape, the audio may mute on some camcorder.
camcorder models. At the recorded part, only video is • For details on the types of camcorder that have an “external
recorded. REC control” function and on motion detection, refer to the
• When HDV recording with this unit, if you start the tape “Guide to supported models and their functions” supplied
recording with the camcorder, the i.LINK output stream is with this unit.
cut for about 0.5 seconds, so when that video is recorded
onto this unit, it is the cut form. In this case, the file will be – Connecting to a camcorder without an “external
separated before and after changing the tape recording REC control” function (FOLLOW mode)
started. When connected to a camcorder that has no external REC
• The file will be separated automatically every time the control function, this unit regularly checks the status of
recording time of one clip over about 20 minutes but this the camcorder and follows its recording operation.
clip is operated as a same clip.
• If the i.LINK cable is disconnected or the power of the Camcorder STANDBY REC STANDBY
connecting device turned off during recording, recording
stops but the data recorded until that point is recorded.
• If the power of this unit is turned off by battery exhaustion This unit STANDBY REC STANDBY
9
Downloaded from www.Manualslib.com manuals search engine
x Recording on this unit during camcorder tape
Cache recording mode
replacement
When connected to a camcorder that has an external REC The most recent approximately maximum 14 seconds of
control function, you can record video on this unit only video and audio captured by the camcorder are held in a
while changing the tape of the camcorder. buffer memory and automatically recorded when the
recording button is pressed.
5 minutes before end of tape
Camcorder REC Changing the tape REC STANDBY To set cache recording
REC STOP
Select [CACHE] from [REC MODE] on the menu screen.
This unit STANDBY REC STANDBY
Notes
1 Press the CAM LINK button of this unit and set it to • After cache recording, it may take about 30 seconds to write
ON. data of the cache part.
2 Set the [CAM LINK SEL] setting of this unit to
[SYNCHRO]. Interval recording mode
3 Set the [EXT REC CTRL] setting of the camcorder to Records a series of videos at regular intervals.
[RELAY]. This function is useful to observe things like cloud
4 Connect the camcorder to this unit via an i.LINK cable. movements or daylight changes. Only DVCAM/DV format is
5 Press the REC START/STOP button of the camcorder to valid.
start recording.
Selecting an interval recording time
• When the remaining time of the tape is less than 5 minutes,
Select [SETTING] t [INTERVAL] t [REC TIME] on the
the camcorder sends a command to this unit to start
menu screen to set the time.
recording.
You can select [0.5sec], [1sec], [1.5sec] or [2sec].
• The recording by this unit can be stopped from the
camcorder after changing the tape or by pressing the STOP Setting the interval time
button of this unit. Select [SETTING] t [INTERVAL] t [INT TIME] on the
• The noise of the tape change is recorded. menu screen to set the time.
• The above Step 3 is for the HVR-Z7/S270 series. For details You can select [30sec], [1min], [5min] or [10min].
on another camcorder you want to connect to this unit,
refer to the operating instructions supplied with that Setting interval recording
camcorder. Select [INTERVAL] from [REC MODE] on the menu screen.
• For details on camcorders that have an “external REC
control” function and on motion detection, refer to the LCD screen display in interval recording mode
“Guide to supported models and their functions” supplied
with this unit.
Notes
• During RELAY recording, the cache recording cannot be Remains on during
operated. recording and blinks
during standby
x Recording video from this unit
You can use this unit to start or stop recording a video
input signal from an i.LINK without linked operation to a
device connected via i.LINK.
10
Downloaded from www.Manualslib.com manuals search engine
Loop recording mode
Repeats overwrite-recording using the available space on the
CompactFlash.
You cannot select this mode if the remaining recording time
is less than 5 minutes (CompactFlash icon is flashing).
Notes
• The speed will slow according to the volume of data being
written because of limitations of the CompactFlash
capacity. For that reason, the following usages are
recommended when operating loop recording;
– Use a new CompactFlash (more than 300x).
– Format a CompactFlash before starting loop recording.
• CAM LINK is turned OFF automatically while in the
interval and loop recording modes. Press the REC button to
starting recording.
• The data recorded by loop recording mode is updated at
regular intervals. When updating the data, the whole
recording time may be shortened.
• Updates the data regardless of update intervals when
starting recording by a camcorder during loop recording
mode in HDV.
11
Downloaded from www.Manualslib.com manuals search engine
Playback the image recorded on a
CompactFlash in this unit
To play back video clip recorded on a CompactFlash in this
unit, you need to connect this unit to a playback device via an Trick playback
i.LINK cable. When the playback image is output to i.LINK, the clip is
played at 3x, 6x, and 9x the normal speed.
– ALL REPEAT
Standard playback ALL REPEAT plays back all recorded images in this unit
In this mode, the recorded clip in this unit is output to the to the last clip then goes back to the first clip and repeats
i.LINK depending on the type of format. playback.
File B-2
File B-3
File C-2
File C-3
12
Downloaded from www.Manualslib.com manuals search engine
You can record the time code of the HVR-Z7/S270 without a
Useful functions in combination tape in the HVR-Z7/S270.
with HVR-Z7/S270
If you want to record video using the time code of
Tapeless external REC control the HVR-Z7/S270, set the time code setting of the
HVR-Z7/S270 as follows.
Even if there is no tape in the HVR-Z7/S270, you can start or
stop recording the image on this unit. Time code value always advances.
• TC MAKE ........ PRESET
Set the EXT REC CTRL setting of the HVR-Z7/S270 as
• TC RUN ........... FREE RUN
follows.
• REC CTRL MODE ..... EXT ONLY Time code value only advances during recording.
You can start or stop recording the image on a • TC MAKE ........ PRESET
CompactFlash in this unit with START/STOP button only. • TC RUN ........... REC RUN
(If there is a tape in the HVR-Z7/S270, you can start
recording video data with REC button of the video camera In combination with the time code settings of the HVR-Z7/
operation part, stop recording video data with STOP button S270, this unit operates as follows.
of the video camera operation part on the tape.)
Time code of this Time code of this
Tips TC MAKE TC RUN unit with a tape in unit without a tape
If there is no tape in the SYNCHRONUS or RELAY settings, the HVR-Z7/S270 in the HVR-Z7/S270
you can start or stop recording the image on a CompactFlash
in this unit. When starting The internal time
recording on a tape, code of this unit
video is recorded runs automatically.
• STBY COMMAND ..... Desired setting
using the time code
* For details, refer to the operating instructions for the REGENERATE – of the tape base.
external REC control of the HVR-Z7/S270. If the time code of
the tape base cannot
Set this unit as follows. be read, the time
• CAM LINK SEL .......... SYNCHRO code starts from
• Press the CAM LINK button to set to CAM LINK [ON]. 00:00:00:01.
When starting When starting
recording on a tape recording on
or CompactFlash in CompactFlash in
this unit, the time this unit, the time
REC RUN code value advances code value
from the preset time advances from the
PRESET code of the HVR- preset time code of
Z7/S270. the HVR-Z7/S270.
The preset time code The preset time
value advances code value
FREE RUN constantly and data advances constantly
is recorded using the and data is recorded
data code. using the data code.
13
Downloaded from www.Manualslib.com manuals search engine
Display the operational status of this unit on the HVR-Z7/S270 LCD screen
CAMERA mode
– Indicators – Status check indicator
• The following information can be displayed on the LCD • The following information can be displayed on the status
screen of the HVR-Z7/S270. check indicator (CAMERA mode) of the HVR-Z7/S270.
1
2
TIME CODE
CompactFlash mode Mode icon Displays the time code during recording.
STANDBY x CLIP
Displays the clip number during recording.
REC z
CAM LINK
Displays the CAM LINK status of this unit.
(When CAM LINK [OFF] is set, you cannot record from the
HVR-Z7/S270.)
REMAIN
Displays the CompactFlash remaining recording time.
REMAIN
Displays the battery level.
(When connected to an AC adaptor/charger, “AC” is
displayed.)
Not displayed when this unit is connected to the camcorder.
It is displayed when the unit is connected to the i.LINK
cradle.
14
Downloaded from www.Manualslib.com manuals search engine
VCR mode
– Indicators – Status check indicator
• The following information can be displayed on the LCD • The following information can be displayed on the status
screen of the HVR-Z7/S270. check indicator (VCR mode) of the HVR-Z7/S270.
2
1
3
REW m
REMAIN
Displays the CompactFlash remaining recording time.
PLAY PAUSE u
REMAIN
REC z Displays the battery level.
(When this unit is connected to an AC adaptor/charger,
3 Time code of the playback signal of this unit “AC” is displayed.)
This time code is displayed during playback of a video Not displayed when this unit is connected to the camcorder.
recorded by this unit. It is displayed when the unit is connected to the i.LINK
cradle.
4 Data code
This data code is displayed during playback of a video
recorded by this unit.
15
Downloaded from www.Manualslib.com manuals search engine
Using in COMPUTER mode
Connecting to a computer
16
Downloaded from www.Manualslib.com manuals search engine
Menu organization (COMPUTER mode)
root HDV
DV-NTSC
DV-PAL
DRIVE
SETTING TC FORMAT AUTO
NDF
DF
DV FILETYPE AVI
RAW DV
CAMERA NO
*Boldface settings are default settings.
Notes
HDV
• For the following cases, operate “Safety remove Device (for
Operate in the VIDEO mode. Set this mode when reading or
Windows)” or “Remove by putting the media icon into the
writing HDV stream data on a CompactFlash in this unit
trash (for Mac OS)” etc., and check that the access lamp
using editing software.
turns off.
– When switching the each modes DRIVE, HDV or DV-
DV-NTSC NTSC, DV-PAL
– When disconnecting the i.LINK cable from the computer
Operate in the VIDEO mode. Set this mode when reading or – When turning off the power of this unit
writing DV (NTSC format) stream data on a CompactFlash in To recognize this unit again after these operations,
this unit using the editing software. disconnect i.LINK cable from the computer once, then
reconnect it.
DV-PAL • Depending on the video editing software, this unit may not
be recognized without switching the mode before starting
Operate in the VIDEO mode. Set this mode when reading or the software.
writing DV (PAL format) stream data on a CompactFlash in • If you change the operation mode frequently, the computer
this unit using the editing software. and this unit may not communicate correctly. Switch the
mode of this unit at intervals about 5 seconds or more.
• HDV, DV-NTSC, and DV-PAL mode may not be
DRIVE recognized because of a limitation of the computer when
Operate as an external removable media of the computer. switching them directly.
(Default setting) If that situation occurs, disconnect this unit from the
computer, then select the mode.
• If the combination of the settings of the editing software
SETTING (HDV/DV-NTSC, DV-PAL) and this unit are incorrect,
You can set this when in VIDEO mode. images may be distorted or recognized incorrectly.
Settings are reflected in setting in the VIDEO mode operation
when connecting to a camcorder.
For details about setting, refer to “Menu organization
(VIDEO mode).”
17
Downloaded from www.Manualslib.com manuals search engine
Folder saving format
Folder organization
XX_CCCC_YYYY-MM-DD_hhmmss.M2T
XX_CCCC_YYYY-MM-DD_hhmmss.IDX
XX_CCCC_YYYY-MM-DD_hhmmss.AVI
XX_CCCC_YYYY-MM-DD_hhmmss.IDX
XX_CCCC_YYYY-MM-DD_hhmmss.AVI
XX_CCCC_YYYY-MM-DD_hhmmss.IDX
An actual file name has numbers as the
following information.
XX_CCCC_YYYY-MM-DD_hhmmss.DV
• XX : Camera No. (00 to 99)
XX_CCCC_YYYY-MM-DD_hhmmss.IDX
• CCCC : Clip No. (0001 to 9999)
• YYYY : Year (1995 to 2094) XX_CCCC_YYYY-MM-DD_hhmmss.DV
• MM : Month (01 to 12) XX_CCCC_YYYY-MM-DD_hhmmss.IDX
• DD : Day (01 to 31)
• hh : Hour (00 to 23)
• mm : Minute (00 to 59)
• ss : Second (00 to 59)
• M2T/AVI/DV : Extension
Tracks.dat
When not setting the clock set, file name will be “xx_cccc_0000-00-00_000000.extension.”
When the file is separated, the bottom number of the file name will be counted up.
When cache recording in HDV format, the cache part may be separated as a 14-second file (maximum).
Files
The maximum file size is 4 GB. If a file size exceeds 4 GB, that file is automatically divided.
XX_CCCC_YYYY-MM-DD_hhmmss.M2T XX_CCCC_YYYY-MM-DD_hhmmss.DV
Data recorded in HDV format DV format data recorded when DV FILE TYPE is set to
When playback, HDV compatible playback software is RAW DV
needed. For playback on Windows, Raw DV compatible playback
software is needed.
XX_CCCC_YYYY-MM-DD_hhmmss.AVI
DV format data recorded when DV FILE TYPE is set to XX_CCCC_YYYY-MM-DD_hhmmss.IDX and Tracks.
AVI dat
Information files of recording data in folders
(number of files, number of frames, starting time code,
etc.)
Used with a connection tool. Do not delete this file.
Notes
• During HDV recording, a new file will be created at the recording starting point of the tape.
• Segmented files recorded from HDV stream
Some computer applications cannot play back the transitions between segmented files properly. If this happens, join the files
using the “Sony Recording Unit Utility” or “M2T File Connection Tool” (*).
* Available from the Sony support page
18
Downloaded from www.Manualslib.com manuals search engine
Notes regarding COMPUTER mode
19
Downloaded from www.Manualslib.com manuals search engine
Power supply
20
Downloaded from www.Manualslib.com manuals search engine
AC adaptor/charger
Do not short-circuit the DC plug of the AC adaptor/charger
To connect this unit to a wall outlet
or battery terminal with any metallic objects. This may cause For prolonged operation, such as playing the recorded
a malfunction. images, you can operate this unit from a domestic wall outlet
without worrying about battery life.
To remove the battery pack from this unit Notes on battery pack/AC adaptor
Press the BATT RELEASE button of this unit and slide the • Avoid the following while the ACCESS lamp is lit. Failure
battery pack in the direction of the arrow. to do so may cause malfunction.
– Removing the battery pack
– Removing the AC adaptor (while charging with the AC
adaptor)
• Always turn off the POWER switch before removing the
battery pack or the AC adaptor.
21
Downloaded from www.Manualslib.com manuals search engine
Trouble shooting
Power sources
Symptom Cause/Remedy
This unit gets warm. • This unit may get warmer while you use it. This is not a malfunction.
The remaining battery time indicator • The ambient temperature is too high or too low, or the battery pack has not been
does not indicate the correct time. charged enough. This is not a malfunction.
t Fully charge the battery pack again. If the problem persists, the battery pack
may be worn out. Replace it with a new one (p. 20).
• The indicated time may not be correct in certain circumstances.
The battery pack discharges too • The ambient temperature is too high or too low, or the battery pack has not been
quickly. charged enough. This is not a malfunction.
t Fully charge the battery pack again. If the problem persists, the battery pack
may be worn out. Replace it with a new one (p. 20).
Recording
Symptom Cause/Remedy
Pressing the REC switch does not • This unit is writing the video you just shot to the CompactFlash.
start recording. t Wait for a while and then slide the REC switch.
• The CompactFlash of the unit is full.
t Delete unnecessary images.
t Format this unit by selecting DELETE and then FORMAT.
The ACCESS lamp remains on even • This unit is recording the image you just shot.
when you stop recording. t Do not remove the AC adaptor or the battery pack while the lamp is turned on.
Recording stops. • Fragmentation has occurred.
t Format this unit by selecting DELETE and then FORMAT.
22
Downloaded from www.Manualslib.com manuals search engine
Connecting a computer
Symptom Cause/Remedy
An error message appears when you t Set the computer display as follows:
place the supplied CD-ROM in your – 1024 × 768 dots or more, high color (16 bits, 65,000 colors) or more.
computer.
The image or sound on this unit • Depending on the computer you are using, the played back image or sound may
cannot be played back correctly. stop temporarily, but this does not affect the images or sound copied to your
computer.
• Playback software is not installed on your computer.
t Install playback software on your computer.
The extension of a file is not t To display the extension, follow the steps below.
displayed on your computer. 1 In the window folder, click [Tools] t [Folder option...] t [View] tab.
2 Under Advanced Settings, uncheck [Hide file extensions for known file types].
3 Click [OK].
23
Downloaded from www.Manualslib.com manuals search engine
Warning indicators
Self-diagnosis display
When an error occurs the following warning indicators may appear on the LCD screen.
24
Downloaded from www.Manualslib.com manuals search engine
Caution message
25
Downloaded from www.Manualslib.com manuals search engine
About i.LINK
The HDV/DV jack provided on this unit is an i.LINK- To use i.LINK functions of this unit
compliant jack. This section describes the i.LINK standard This unit can be connected to Sony i.LINK-compatible
and its features. devices other than camcorders (e.g. VAIO computers).
This unit may not be compatible with certain i.LINK video
What is i.LINK? devices such as digital televisions, DVD recorders/players
i.LINK is a digital serial interface for sending and receiving and MICROMV recorders/players even if they are equipped
digital video, digital audio, and other data between this unit with an i.LINK jack. Before connecting to another device,
and other equipment equipped with an i.LINK terminal. You confirm whether it is HDV/DVCAM (DV) compatible.
can also control other equipment using i.LINK. For precautions on connecting and the availability of
i.LINK-compatible equipment can be connected using an compatible software applications, refer to the operating
i.LINK cable. Possible applications are operations and data instructions of the device to be connected.
exchange with various digital AV equipment.
When two or more i.LINK-compatible equipment are Notes
connected to this unit, operations and data exchange are • When connecting an i.LINK cable to this unit or a
possible with equipment directly connected to this unit and computer, check the direction of the jack. Forcibly inserting
also with equipment connected to this unit via other the jack may damage the terminal or cause a malfunction.
equipment. • Always connect the i.LINK cable to the computer first and
Note, however, that the method of operation may vary then to this unit. Connecting the i.LINK cable to this unit
depending on the characteristics and specifications of the first may cause this unit to malfunction because of static
equipment to be connected. Also, there are cases where electricity.
operations and data exchange may not be possible even if the • When using an i.LINK cable to connect this unit to a device
connection is made. equipped with an i.LINK jack, switch off the device and
Notes remove the power cord from the AC outlet before
connecting or disconnecting the i.LINK cable. If the i.LINK
• Normally, only one device can be connected to this unit cable is connected or disconnected while the power cord of
using i.LINK cable. When you connect this unit to HDV/ the device is connected to the AC outlet, a high-voltage
DVCAM (DV)-compliant equipment that allows multiple current (8 to 40 V) output from the i.LINK jack of the device
connections, refer to the operating instructions of the will flow into this unit and damage it.
equipment to be connected. • Before changing the HDV/DV format etc. of the camcorder,
• i.LINK is an easy-to-remember term for the IEEE 1394 disconnect the i.LINK cable. Changing the format after
proposed by Sony, and is a trademark approved by many connecting the i.LINK cable, the video signal may not be
corporations in Japan and overseas. recognized correctly.
• IEEE 1394 is an international standard standardized by the
Institute of Electrical and Electronics Engineers. Required i.LINK cable
Use a Sony i.LINK cable.
About the i.LINK baud rate
The maximum baud rate of i.LINK varies depending on the i.LINK and are trademarks of Sony Corporation.
equipment. There are three types.
S100 (Approximately 100 Mbps*)
S200 (Approximately 200 Mbps)
S400 (Approximately 400 Mbps)
The baud rate is listed under “Specifications” in the operating
instructions of individual equipment. It may be indicated
near the i.LINK interface on some equipment.
The baud rate may vary from the indicated value when this
unit is connected to equipment with a different maximum
baud rate.
* What is Mbps?
Mbps stands for “megabits per second.” It is the volume of
data that can be sent or received in 1 second. For example, a
baud rate of 100 Mbps means that 100 megabits of data can
be sent in 1 second.
26
Downloaded from www.Manualslib.com manuals search engine
Optional CompactFlash
CompactFlash
27
Downloaded from www.Manualslib.com manuals search engine
Specifications
System
File system FAT32
CompactFlash 133x 2 GB or more
The capacity is the value when 1
GB equals 1 billion bytes.
The actual usable capacity may
be slightly less because
administrative files etc. are
included.
File format HDV recording MPEG-2TS
(.m2t)
DVCAM/DV recording
AVI-Type1
(.AVI)
RAW DV (.DV)
Input signal
HDV recording/playback
Video: MPEG-2TS
1080/60i, 30p, 24p
1080/50i, 25p
Audio: 2 CH MPEG 1 Audio
Layer2 Stereo (16 bit 48 kHz)
(1/2 CH)
4 CH MPEG 2 Audio
Layer2 Stereo (16 bit 48 kHz)
(3/4 CH)
DVCAM/DV recording/playback
Video: DV embedded
Audio: PCM digital
(12/16 bit, 32k, 48k)
Recordable time 2 GB Approx. 9 minutes
4 GB Approx. 18 minutes
8 GB Approx. 36 minutes
16 GB Approx. 72 minutes
General
Power requirement DC 7.2 V (battery pack)
DC 8.4 V (AC adaptor)
Power consumption 2.2 W
Operating temperature 0 °C to 40 °C (32 °F to 104 °F)
Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)
Operating humidity 20 % (20 °C) to 90 % (35 °C)
(no condensation)
Dimensions
HVR-MRC1 : Approx. 57 × 102 × 34 mm
(2 1/4 × 4 1/8 × 1 3/8 in.)
HVR-MRC1+HVRA-CR1: Approx. 77 × 106 × 51 mm
(3 1/8 × 4 1/4 × 2 1/8 in.)
(including the projecting parts)
(w/h/d)
Mass
HVR-MRC1 : Approx. 130 g (4 oz)
HVR-MRC1+HVRA-CR1: Approx. 210 g (7 oz)
(excluding CompactFlash and
battery pack)
Input/output jack i.LINK
(IEEE1394 6-pin connector S400)
28
Downloaded from www.Manualslib.com manuals search engine
Precautions
LCD screen
• Do not exert excessive pressure on the LCD screen, as it
may cause damage.
• If this unit is used in a cold place, a residual image may
appear on the LCD screen. This is not a malfunction.
• While using this unit, the back of the LCD screen may heat
up. This is not a malfunction.
29
Downloaded from www.Manualslib.com manuals search engine
Getting the best performance from the battery pack
30
Downloaded from www.Manualslib.com manuals search engine
Additional information on this product and answers to
frequently asked questions can be found at our Customer
Support Website.
#5: M1.7 X 3.5 (Tapping) #6: M1.4 X 1.7 #7: M1.7 X 1.6 #8: M1.7 X 3.5 (Tapping)
(Black) (Silver) (Black) (Silver)
3-080-204-01 2-598-474-01 7-627-552-18 3-078-890-01
#9: M1.7 X 5.0 (Tapping) #10: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping) #12: M1.7 X 5.0 (Tapping)
(Silver) (Silver) (Silver) (Black)
3-078-890-21 2-599-475-31 3-078-890-11 3-080-204-21
#13: M1.7 X 2.5 (Tapping) #14: M1.7 X 2.5 #15: M1.4 X 1.5 #16: M1.4 X 2.5
(Silver) (Silver) (Silver) (Silver)
3-085-397-01 2-599-475-11 3-062-214-01 2-586-337-01
#17: M1.7 X 1.5 #18: M1.4 X 2.5 #19: M1.2 X 4.0 (Tapping) #20: M1.4 X 3.0
(Silver) (Silver) (Red) (Silver)
2-586-389-01 2-635-591-21 3-086-156-21 2-635-591-31
1.5
2.5 4.0 3.0
3.5
#21: M1.4 X 3.0 #22: M1.7 X 5.0 (Tapping) #23: M1.7 X 4.0 (Tapping) #24: B1.7 X 5.5 (Tapping)
(Black) (Silver) (Black) (Black)
2-662-396-21 3-083-261-01 3-080-204-11 4-679-805-11
#25: M1.7 X 3.0 #26: M1.4 X 2.0 #27: M1.4 X 2.0 #28: M1.4 X 4.0 (Tapping)
(Black) (Silver) (Black) (Silver)
2-635-562-21 2-635-591-11 2-662-396-11 3-348-998-61
#29: M1.4 X 2.5 #30: M1.2 X 3.5 (Tapping) #31: M3.0 X 4.0 #32: M2.0 X 4.5 (Tapping)
(Black) (White) (Silver) (Silver)
2-662-396-01 3-086-156-11 2-102-434-01 2-102-498-01
#33: M3.0 X 6.0 #34: M3.0 X 8.0 #35: M4.0 X 6.0 (Tapping) #36: M3.0 X 6.0
(Silver) (Black) (Silver) (Silver)
3-077-331-21 3-077-331-41 3-975-291-02 4-886-821-11
#37: M2.0 X 6.0 (Tapping) #38: M3.0 X 20.0 (Tapping) #39: M2.6 X 5.0 (Tapping) #40: M2.0 X 4.0 (Tapping)
(Black) (Silver) (Black) (Silver)
3-080-206-31 7-685-651-79 7-685-791-09 7-685-851-04
3.0
20.0
6.0 5.0 4.0
#41: M3.0 X 8.0 (Tapping) #42: M2.0 X 4.0 (Tapping) #43: M1.7 X 4.0 #44: M1.7 X 3.0 (Tapping)
(Silver) (Silver) (Red) (Silver)
3-065-748-01 7-628-253-00 2-660-401-31 3-078-890-61
#45: M1.4 X 2.5 #46: M1.7 X 3.0 #47: M1.4 X 3.0 (Tapping) #48: M1.7 X 2.5
(Silver) (Red) (Silver) (Silver)
2-587-151-01 2-660-401-11 2-665-774-01 3-973-497-91
#49: M2.0 X 4.0 #50: M2.0 X 3.0 #51: M2.0 X 2.5 #52: M2.0 X 4.0 (Tapping)
(Black) (Red) (Silver) (Black)
2-630-005-31 2-891-494-11 3-073-686-01 3-080-206-11
#53: M2.0 X 5.0 (Tapping) #54: M1.75 X 6.0 (Tapping) #55: M2.0 X 4.0 #56: M2.0 X 3.5
(Black) (Black) (Silver) (Silver)
3-080-206-21 3-318-203-11 2-655-582-11 3-067-187-11
#57: M1.7 X 4.0 #58: M2.0 X 6.0 (Tapping) #59: M2.0 X 5.0 (Tapping) #60: M2.6 X 5.0
(Black) (Silver) (Silver) (Black)
7-627-852-18 3-719-408-11 3-080-205-21 3-061-062-11
#61: M3.0 X 10.0 #62: M2.0 X 3.0 #63: M5.0 X 12.5 #64: M1.7 X 5.0 (Tapping)
(Black) (Silver) (Black) (Silver)
7-682-549-09 3-080-202-21 3-060-811-21 2-666-551-21
10.0 12.5
3.0 5.0
#65: M1.4 X 3.5 #66: M1.4 X 1.4 #67: M1.4 X 2.0 #68: M1.7 X 4.0
(Silver) (Silver) (Silver) (Silver)
2-635-591-01 2-635-591-41 3-389-523-16 2-655-581-01
#69: M1.7 X 3.0 #70: M1.7 X 5.0 #71: M1.4 X 2.0 #72: M1.4 X 2.0
(Silver) (Silver) (Red) (Silver)
2-599-475-21 2-599-475-41 3-208-537-01 4-663-621-41
#73: M1.2 X 4.0 (Tapping) #74: M1.7 X 6.0 (Tapping) #75: M1.7 X 3.5 (Tapping) #76: M1.7 X 4.0 (Tapping)
(Black) (Silver) (Silver) (Silver)
3-086-156-61 2-666-551-31 2-666-551-01 2-666-551-11
#77: M1.2 X 5.0 (Tapping) #78: M1.4 X 3.5 #79: M1.4X 2.0 #80: M1.4X 2.0
(Silver) (Red) (Silver) (Black)
3-086-156-31 3-208-537-11 2-587-151-11 3-279-411-01
#81: M1.7 X 2.5 #82: M1.4 X 1.4 #83: M1.7 X 7.0 (Tapping) #84: M2.0 X 3.0
(Silver) (Silver) (Black) (Silver)
2-515-756-01 3-272-251-01 3-080-204-41 3-072-453-11
#85: M1.7 X 2.5 #86: M1.7 X 4.0 (Tapping) #87: M1.6 X 5.3 #88: M1.6 X 5.9 (Tapping)
(Black) (Silver) (Black) (Silver)
2-515-483-11 2-695-434-21 2-689-328-01 2-689-015-01
5.9
2.5 5.3
4.0
#89: M2.0 X 5.5 (Tapping) #90: M1.7 X 3.0 #91: M1.7 X 3.0 (Tapping) #92: M2.0 X 3.9
(Silver) (Silver) (Silver) (Black)
2-695-575-01 3-271-395-01 2-695-434-11 3-268-954-01
#93: M1.7 X 3.5 (Tapping) #94: M1.7 X 4.0 #95: M3.0 X 8.0 (Tapping) #96: M1.4 X 2.5
(Silver) (Black) (Black) (Silver)
3-254-082-01 2-515-483-31 7-685-646-79 2-587-151-21
#97: M1.4 X 2.5 #98: M3.0 X 8.0 #99: M2.5 X 6.0 (Tapping) #100: M2.0 X 6.0
(Black) (Silver) (Silver) (Black)
2-662-396-31 3-077-331-01 3-776-750-02 3-080-203-51
#101: M2.0 X 5.0 #102: M2.6 X 8.0 #103: M2.6 X 10.0 #104: M3.0 X 8.0
(Silver) (Black) (Silver) (Black)
7-621-555-39 7-621-284-30 7-685-794-09 7-682-548-09
#105: M2.0 X 4.0 #106: M2.0 X 6.0 #107: M2.0 X 5.0 #108: M1.7 X 3.0 (Tapping)
(Red) (Black) (Silver) (Black)
2-891-494-31 3-713-786-11 3-032-750-01 2-695-430-01
#109: M1.7 X 3.0 #110: M2.0 X 3.0 #111: M1.7 X 4.0 (Tapping) #112: M1.4 X 5.0
(Black) (Black) (Black) (Black)
2-515-483-21 2-630-005-21 2-887-124-01 2-178-410-11
#113: M1.7 X 5.0 #114: M2.0 X 5.5 (Tapping) #115: M1.4 X 3.5 (Tapping) #116: M2.0 X 3.5 (Tapping)
(Black) (Silver) (Silver) (Silver)
2-635-562-41 2-698-464-01 3-348-998-51 2-695-435-01
#117: M1.7 X 4.5 (Tapping) #118: M1.4 X 2.0 #119: M2.6 X 5.0 #120: M2.6 X 6.0
(Silver) (Black) (Black) (Silver)
2-695-429-31 2-655-580-01 7-627-556-58 7-621-770-67
#121: M2.0 X 4.0 (Tapping) #122: M3.0 X 6.0 #123: M4.0 X 8.0 #124: M1.7 X 2.0
(Silver) (Black) (Black) (Silver)
3-080-205-11 7-682-547-09 7-682-561-09 2-599-475-01
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2008.01 Official Release — —
1.1 2008.06 Revised-1 • Change of Repair Parts Yes
(A1 DI08-162) S.M. revised: Page 5-5, Page 5-6, Page 5-7
1.2 2009.03 Revised-2 • Change of Repair Parts Yes
(A2 DI08-386) S.M. revised: Page 5-2, Page 5-3, Page 5-4,
Page 5-5, Page 5-7
HVR-MRC1