Wf) Vindexhemnn
Mil
Acceptable Weld Joint
Home / |B-Pro Information / Acceptable Weld Joint
Some Acceptable Weld Joint as per IBR Regulations
ISr.No| Type ofJoint | IBR Regulation No. | Design Notes | Figure
Butt
125(a) Figure- | Applicable plate thickness
1 welded 48 xi/6 less than 20 mm
joint
2 weed 125(a) Applicable plate thickness less
* Figure-3 than 20 mm
joint
3 | Butt welded joint | x1/3eigeg | 125(@) Figure- Applicable plate thickness
wee 1&XiI/5 above than 20 mm
joint
idea 125(a) Figure- Applicable plate thickness
wee 2&XIN6 above than 20 mm
joint
Shelltohead butt | Figure- | Outside diameter
join 4a matchoy
Wi
Lergamel 2%
Pressure side
Shelltohead butt | _ Inside diameter Cd
join match 7
U8 (1,— 14) 807 NOT LESS THAN 58 me
Shelltohead | iq | Dished end thicker than shellcither
butt join side Taper joint
Le te 1) 97 WoT LSS
Shell tohead | xlIN0 | Shell thicker than Dished end. Either
butt join
side Taper acceptable10 Nozzle pipe / Shell to WN Flange 28(ix)
joint (a)
1h Nozzle pipe / Shell to WN Flange 28(ix)
joint (b)
2 Nozzle pipe / Shell to WN Flange 28(ix)
joint {c)SMM.
MIN. RAD. |
\
13. | Nozzle to shell /Dished end joint- | 365/29 | Set-on
Without RF pad xI/93 Nozzle
14 | Nozzletoshell/Dished | 5.6, | Setin Nozzle (Single vee with
end joint Without RF pad Back gouge) Full Penetration a
15 | Nozzletoshell/Dishedend | xII/8sD | —Set-in Nozzle (Double
joint Without RF pad (8) vee) Full PenetrationL NZ
VA,
9
2
x] [ pone
1 | Nozletoshell/Dished | yiigiia) | Partial Penetration
end joint weld joint
a7 | Nozzletoshell /Dished | yujgeis) | Partial Penetration
end joint weld joint
18 Nozzle to shell / Dished end xi/85F | Double vee Full
joint with RF Pad
PenetrationNozzle to shell / Dished end
Single vee Full
9 joint with RF Pad xive7 Penetration
go | TubetoTubesheet | 6, | Seal weld with light
joint expansion
2 Tube to xI/67A | Strength weld with light
Tubesheet joint
expansion22
Flange to shell joint
29
SLR.
wk
SMM.
8
of Icke
ty BUT NOT LESS THAN 5 mm
te SUT NOT LESS THAN 6 mm
ts BUT NOT LESS THAN 6 mm
Flange to shell joint
30
a
e
2
aa
3
WL
= O5¢ te BUT NOT LESS THAN S rm
= Bm
C= ty BUT NOT LESS THAN 10 mm
E
BUT NOT LESS THAN 8 mm
24
Flange to shell joint
32A= 05 ty BUT NOT LESS THEN 5 mm
mm MW
5 BUT NOT LESS THEN 10am
‘St, AUT NOT LESS THAN 6 mm
25 | Flange to shell joint | 31 rr 2
3} |e El
8 = ty BUT NOT LESS THAN 5 mm
E = 3/2 ts BUT NOT LESS THAN & mm
26 | Flangetoshelljoint | 33
ella [|
B= mm
E = 3/2 4, BUT NOT LESS THAN 5 mm
F = 1 mm We
27 | Flange toshelljoint | 33WE ARE PROUD TO SAY
e°
minke Dy ce
Contact