Professional Documents
Culture Documents
MAX16807/MAX16808
The MAX16807/MAX16808 are integrated, high-efficien- ♦ Eight Constant-Current Output Channels (Up to
55mA Each)
cy white or RGB LED drivers. They are designed for
LCD backlighting and other LED lighting applications ♦ ±3% Current Matching Among Outputs
with multiple strings of LEDs. The MAX16807/ ♦ Paralleling Channels Allows Higher Current per
LED String
MAX16808’s current-mode PWM controller regulates
the necessary voltage to the LED array. Depending on ♦ Outputs Rated for 36V Continuous Voltage
the input voltage and LED voltage range, it can be ♦ Output-Enable Pin for PWM Dimming (Up to 30kHz)
used with boost or buck-boost (SEPIC) topologies. The ♦ One Resistor Sets LED Current for All Channels
MAX16807/MAX16808 feature an 8V to 26.5V input volt- ♦ Wide Dimming Ratio Up to 5000:1
age range. A wide range of adjustable frequency ♦ Low Current-Sense Reference (300mV) for High
(20kHz to 1MHz) allows design optimization for efficien- Efficiency
cy and minimum board space. ♦ 8V to 26.5V Input Voltage or Higher with External
Biasing Devices
The MAX16807/MAX16808 LED drivers include eight
♦ Open LED Detection (MAX16808)
open-drain, constant-current-sinking LED driver outputs
rated for 36V continuous operation. The LED current- ♦ 4-Wire Serial Interface to Control Individual
Output Channels
control circuitry achieves ±3% current matching among
strings and enables paralleling of outputs for LED string Applications
currents higher than 55mA. The output-enable pin is LCD White or RGB LED Backlighting:
used for simultaneous PWM dimming of all output chan- LCD TVs, Desktop, and Notebook Panels
nels. Dimming frequency range is 50Hz to 30kHz and Automotive Navigation, Heads-Up,
dimming ratio is up to 5000:1. The constant-current out- and Infotainment Displays
puts are single resistor programmable and the LED cur- Industrial and Medical Displays
rent can be adjusted up to 55mA per output channel. Ambient, Mood, and Accent Lighting
The MAX16807/MAX16808 operate either in stand-alone Ordering Information
mode or with a microcontroller (µC) using an industry-
standard, 4-wire serial interface. The MAX16808 includes TEMP PKG
circuitry that automatically detects open-circuit LEDs. PART PIN-PACKAGE
RANGE CODE
The MAX16807/MAX16808 include overtemperature MAX16807AUI+ -40°C to +125°C 28 TSSOP-EP** U28ME-1
protection, operate over the full -40°C to +125°C tem-
MAX16808AUI+* -40°C to +125°C 28 TSSOP-EP** U28ME-1
perature range, and are available in a thermally
enhanced, 28-pin TSSOP exposed paddle package. +Denotes lead-free package.
*Future product—contact factory for availability.
Pin Configurations appear at end of data sheet. **EP = Exposed paddle.
Typical Operating Circuits
VIN VOUT
L D
Q COUT R1 LEDs
CC2
RCS
CC1 RC1
R2
CREF CT
Typical Operating Circuits continued at end of data sheet.
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
ABSOLUTE MAXIMUM RATINGS
MAX16807/MAX16808
2 _______________________________________________________________________________________
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
ELECTRICAL CHARACTERISTICS (PWM CONTROLLER) (continued)
MAX16807/MAX16808
(VCC = +15V, V+ = +3V to +5.5V referenced to PGND, RT = 10kΩ, CT = 3.3nF, REF = open, COMP = open, CREF = 0.1µF, VFB = 2V,
CS = AGND, AGND = PGND = 0V; all voltages are measured with respect to AGND, unless otherwise noted. TJ = TA = -40°C to
+125°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
_______________________________________________________________________________________ 3
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
ELECTRICAL CHARACTERISTICS (LED DRIVER)
MAX16807/MAX16808
(V+ = +3V to +5.5V, AGND = PGND = 0V; all voltages are measured with respect to PGND, unless otherwise noted. TA = TJ = -40°C
to +125°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
Standby Current
RSET = 360Ω, fCLK = 5MHz, OE = V+,
(Interface Active, All Output Ports 3.8 4.8 mA
DIN, LE = PGND or V+, DOUT unconnected
High Impedance)
Supply Current
RSET = 360Ω, OE = PGND, DIN,
(Interface Idle, All Output Ports I+ 17 30 mA
LE = V+, DOUT unconnected
Active Low)
INTERFACE (DIN, CLK, DOUT, LE, OE)
Input-Voltage High 0.7
VIH V
(DIN, CLK, LE, OE) x V+
Input-Voltage Low 0.3
VIL V
(DIN, CLK, LE, OE) x V+
Hysteresis Voltage
VHYST 0.8 V
(DIN, CLK, LE, OE)
Input Leakage Current
ILEAK -1 +1 µA
(DIN, CLK)
OE Pullup Current to V+ IOE V+ = 5.5V, OE = PGND 0.25 1.5 25.0 µA
LE Pulldown Current to PGND ILE V+ = 5.5V, LE = V+ 0.25 1.5 25.0 µA
V+
Output-Voltage High (DOUT) VOH ISOURCE = 4mA V
- 0.5V
Output-Voltage Low (DOUT) VOL ISINK = 4mA 0.5 V
0oC ≤ TA ≤ +125°C, VOUT = 1V to 2.5V, RSET =
46.5 50 53.5
360Ω
OUT_ Output Current IOUT_ mA
TA = -40°C, VOUT = 1V to 2.5V,
43 57
RSET = 360Ω
OUT_ Leakage Current OE = V+ 1 µA
OUT_ Fault Detection Threshold
VOUTTH V+ = 5.5V, OE = V+ 0.8 V
(MAX16808)
4 _______________________________________________________________________________________
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
5V TIMING CHARACTERISTICS
MAX16807/MAX16808
(V+ = +4.5V to +5.5V, AGND = PGND = 0V; all voltages are measured with respect to PGND, unless otherwise noted. TA = TJ = -40°C
to +125°C, unless otherwise noted. Typical values are at TA = +25°C.) (Notes 1, 5)
_______________________________________________________________________________________ 5
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
3.3V TIMING CHARACTERISTICS
MAX16807/MAX16808
(V+ = +3V to < +4.5V, AGND = PGND = 0V; all voltages are measured with respect to PGND, unless otherwise noted. TA = TJ = -40°C
to +125°C, unless otherwise noted. Typical values are at TA = +25°C.) (Notes 1, 5)
6 _______________________________________________________________________________________
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
Typical Operating Characteristics
MAX16807/MAX16808
(VCC = +15V, V+ = 3V to 5.5V, RT = 10kΩ, CT = 3.3nF, VREF = COMP = open, CREF = 0.1µF, VFB = 2V, CS = AGND = PGND = 0V.
Typical values are at TA = +25°C, unless otherwise noted.)
MAX16807 toc02
MAX16807 toc03
VCC = 7 5V CT = 560pF
9 VCC RISING
39 4.9
8
37 4.7
7 VCC FALLING
6 35 4.5
ICC (µA)
VCC (V)
ICC (mA)
5 33 4.3
4
31 4.1
3
29 3.9
2
HYSTERESIS
1 27 3.7
0 25 3.5
-40 -25 -10 5 20 35 50 65 80 95 110 125 -40 -25 -10 5 20 35 50 65 80 95 110 125 -40 -25 -10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C) TEMPERATURE (°C) TEMPERATURE (°C)
MAX16807 toc06
MAX16807 toc04
MAX16807 toc05
IREF = 1mA
5.06 4.998
5 00
5.04 4.996
4.95
4.994
5.02
4.90 4.992
VREF (V)
VREF (V)
VREF (V)
OSCILLATOR FREQUENCY (fOSC) OSCILLATOR RT/CT DISCHARGE CURRENT CURRENT-SENSE TRIP THRESHOLD
vs. TEMPERATURE vs. TEMPERATURE vs. TEMPERATURE
550 8.04 0.40
MAX16807 toc08
MAX16807 toc07
MAX16807 toc09
RT = 3 65kΩ VRT/CT = 2V
540 CT = 560pF 8.02 0.38
RT/CT DISCHARGE CURRENT (mA)
OSCILLATOR FREQUENCY (kHz)
530 0.36
8.00
520 0.34
CS THRESHOLD (V)
_______________________________________________________________________________________ 7
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
MAX16807/MAX16808
TIMING RESISTANCE OUT IMPEDANCE vs. TEMPERATURE OUT IMPEDANCE vs. TEMPERATURE
vs. OSCILLATOR FREQUENCY (RDS_ON PMOS DRIVER) (RDS_ON NMOS DRIVER)
1000 5.0 10
MAX16807 toc11
MAX16807 toc10
MAX16807 toc12
4.8 ISOURCE = 100mA ISINK = 200mA
4.6 9
CT = 1nF
4.4 8
100 CT = 560pF 4.2
7
CT = 220pF 4.0
RDS_ON (Ω)
RDS_ON (Ω)
3.8 6
RT (kΩ)
CT = 100pF 3.6
10 5
3.4
3.2 4
CT = 10nF 3.0
3
1 CT = 4.7nF 2.8
CT = 3 3nF 2.6 2
2.4
CT = 2.2nF 1
2.2
0.1 2.0 0
10k 100k 1M 10M -40 -25 -10 5 20 35 50 65 80 95 110 125 -40 -25 -10 5 20 35 50 65 80 95 110 125
FREQUENCY (Hz) TEMPERATURE (°C) TEMPERATURE (°C)
PROPAGATION DELAY FROM CURRENT-LIMIT ERROR-AMPLIFIER OPEN-LOOP GAIN COMP VOLTAGE LEVEL TO TURN
COMPARATOR TO OUT vs. TEMPERATURE AND PHASE vs. FREQUENCY OFF DEVICE vs. TEMPERATURE
MAX16807 toc14
100 2.3
MAX16807 toc15
MAX16807 toc13
2.1
-40
PHASE (DEGREES)
70 100
GAIN
2.0
VCOMP (V)
60 -65
GAIN (dB)
80
50 PHASE 1.9
60 -90
40 1.8
40 -115
30
20 -140 1.7
20
10 0 -165 1.6
55
50 TA = +125°C TA = +25°C
ICC (mA)
45 1.90
TA = -40°C
40 TA = -40°C
35
1.85
30
25
20 1.80
20 120 220 320 420 520 620 720 820 920 1020 3.0 35 40 4.5 50 5.5
FREQUENCY (kHz) SUPPLY VOLTAGE (V)
8 _______________________________________________________________________________________
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
Typical Operating Characteristics (continued)
MAX16807/MAX16808
(VCC = +15V, V+ = 3V to 5.5V, RT = 10kΩ, CT = 3.3nF, VREF = COMP = open, CREF = 0.1µF, VFB = 2V, CS = AGND = PGND = 0V.
Typical values are at TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT vs. SUPPLY VOLTAGE SUPPLY CURRENT vs. SUPPLY VOLTAGE
(INTERFACE IDLE, ALL OUTPUTS OFF, RSET = 360Ω) (INTERFACE IDLE, ALL OUTPUTS ON, RSET = 720Ω)
3.70 20
MAX16807 toc19
MAX16807 toc18
TA = +125°C TA = +85°C
17
3 65 TA = +125°C TA = +85°C
SUPPLY CURRENT (mA)
3 50 5
30 35 4.0 45 5.0 5.5 30 3.5 4.0 45 5.0 55
SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V)
SUPPLY CURRENT vs. SUPPLY VOLTAGE OUT_ CURRENT vs. OUT_ VOLTAGE
(INTERFACE IDLE, ALL OUTPUTS ON, RSET = 360Ω) (RSET = 720Ω, V+ = 3.3V)
25 30
MAX16807 toc21
MAX16807 toc20
22 25
TA = +125°C TA = +85°C
SUPPLY CURRENT (mA)
TA = -40°C
OUT_ CURRENT (mA)
20
19 TA = +25°C
15
TA = +85°C
16
TA = +125°C
10
13 TA = +25°C 5
TA = -40°C
10 0
30 3.5 4.0 45 5.0 55 0 0.5 10 1.5 20 2.5 30
SUPPLY VOLTAGE (V) OUT_ VOLTAGE (V)
OUT_ CURRENT vs. OUT_ VOLTAGE OUT_ CURRENT vs. OUT_ VOLTAGE
(RSET = 360Ω, V+ = 3.3V) (RSET = 720Ω, V+ = 5.0V)
60 30
MAX16807 toc23
MAX16807 toc22
50 25
OUT_ CURRENT (mA)
OUT_ CURRENT (mA)
40 20 TA = -40°C
TA = +25°C
30 TA = -40°C 15
TA = +25°C TA = +85°C
20 10 TA = +125°C
TA = +85°C
10 TA = +125°C 5
0 0
0 05 1.0 15 2.0 25 3.0 0 05 1.0 15 2.0 25 3.0
OUT_ VOLTAGE (V) OUT_ VOLTAGE (V)
_______________________________________________________________________________________ 9
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
Typical Operating Characteristics (continued)
MAX16807/MAX16808
(VCC = +15V, V+ = 3V to 5.5V, RT = 10kΩ, CT = 3.3nF, VREF = COMP = open, CREF = 0.1µF, VFB = 2V, CS = AGND = PGND = 0V.
Typical values are at TA = +25°C, unless otherwise noted.)
OUT_ CURRENT vs. OUT_ VOLTAGE OUT_ CURRENT vs. SUPPLY VOLTAGE V+
(RSET = 360Ω, V+ = 5.0V) (RSET = 720Ω, VOUT = 2V)
60 26.0
MAX16807 toc25
MAX16807 toc24
50
25.5 TA = +85°C
40 TA = +125°C
TA = -40°C
TA = +25°C
30 25.0
TA = +85°C
20 TA = +125°C TA = +25°C
24.5 TA = -40°C
10
0 24.0
0 0.5 1.0 1.5 2.0 2.5 3.0 3.0 3.5 4.0 4.5 5.0 55
OUT_ VOLTAGE (V) SUPPLY VOLTAGE (V)
OUT_ CURRENT vs. SUPPLY VOLTAGE V+ OUT_ CURRENT vs. SET RESISTANCE
(RSET = 360Ω, VOUT = 2V) (V+ = 5.0V)
52 50
MAX16807 toc26
MAX16807 toc27
40
51 TA = +85°C
OUT_ CURRENT (mA)
OUT_ CURRENT (mA)
TA = +125°C
30
50
20
TA = +25°C
49 TA = -40°C 10
48 0
3.0 35 4.0 45 5.0 5.5 0 1 2 3 4 5
SUPPLY VOLTAGE (V) RSET (kΩ)
10 ______________________________________________________________________________________
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
Pin Description
MAX16807/MAX16808
PIN NAME FUNCTION
1, 13, 28 N.C. No Connection. Not internally connected. Leave unconnected.
2 AGND Analog Ground
3 OUT MOSFET Driver Output OUT. Connects to the gate of the external n-channel MOSFET.
Power-Supply Input. Bypass VCC to AGND with a 0.1µF ceramic capacitor or a parallel combination
4 VCC
of a 0.1µF and a higher value ceramic capacitor.
5 REF 5V Reference Output. Bypass REF to AGND with a 0.1µF ceramic capacitor.
6–9 OUT4–OUT7 LED Driver Outputs. OUT4–OUT7 are open-drain, constant-current-sinking outputs rated for 36V.
Active-Low Output Enable Input. Drive OE low to PGND to enable the OUT0–OUT7. Drive OE high to
10 OE
disable OUT0–OUT7.
Serial-Data Output. Data is clocked out of the 8-bit internal shift register to DOUT on CLK’s rising
11 DOUT
edge.
12 SET LED Current Setting. Connect RSET from SET to PGND to set the LED current.
14 V+ LED Driver Positive Supply Voltage. Bypass V+ to PGND with a 0.1µF ceramic capacitor.
15, 16 PGND Power Ground
17 DIN Serial-Data Input
18 CLK Serial-Clock Input
Latch-Enable Input. Data is loaded transparently from the internal shift register(s) to the output
19 LE latch(es) while LE is high. Data is latched into the output latch(es) on LE’s falling edge, and retained
while LE is low.
20–23 OUT0–OUT3 LED Driver Outputs. OUT0–OUT3 are open-drain, constant-current-sinking outputs rated for 36V.
24 COMP Error-Amplifier Output
25 FB Error-Amplifier Inverting Input
26 CS PWM Controller Current-Sense Input
PWM Controller Timing Resistor/Capacitor Connection. A resistor RT from RTCT to REF and a
27 RTCT
capacitor CT from RTCT to AGND set the oscillator frequency.
Exposed Paddle. Connect to the ground plane for improved power dissipation. Do not use as the
— EP
only ground connection for the part.
______________________________________________________________________________________ 11
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
ode of a string of LEDs connected in series. The con- The MAX16808 includes circuitry that automatically
MAX16807/MAX16808
stant-current capability is up to 55mA per output, set detects open-circuit LEDs. Fault status is loaded into the
for all 8 outputs by an external resistor, R SET . The serial-interface shift register when LE goes high and is
devices can operate in a stand-alone mode (see the automatically shifted out on DOUT when the next data
Typical Operating Circuits.) transmission is shifted in. The number of channels can be
expanded by using the MAX6970 and MAX6971 family in
conjunction with the MAX16807 and MAX16808.
UVLO
MAX16807 VOLTAGE-
DIVIDER
REFERENCE PREREG VCC
2 5V 5V
26.5V
THERMAL
SHUTDOWN
VDD
EN_REF
BG 5V REG REF
SNS
REG_OK
DELAY VOLTAGE
DIVIDER
AGND
VCC
300mV
ILIM
S Q OUT
R
CS
CPWM
2R
VEA
CLK
FB
COMP R OSC Q
RTCT
CLK
SERIAL-TO-PARALLEL SHIFT REG STER
DIN D0 D1 D2 D3 D4 D5 D6 D7 DOUT
OUTPUT LATCHES
POWER-ON
LE D0 D1 D2 D3 D4 D5 D6 D7 RESET V+
OE
V+
CONSTANT-CURRENT SINK
THERMAL CURRENT
D0 D1 D2 D3 D4 D5 D6 D7 REFERENCE SET
SHUTDOWN
PGND
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
12 ______________________________________________________________________________________
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
MAX16807/MAX16808
UVLO
MAX16808 VOLTAGE-
DIVIDER
REFERENCE PREREG VCC
2 5V 5V
26.5V
THERMAL
SHUTDOWN
VDD
EN_REF
BG 5V REG REF
SNS
REG_OK
DELAY VOLTAGE
DIVIDER
AGND
VCC
300mV
ILIM
S Q OUT
R
CS
CPWM
2R
VEA
CLK
FB
COMP R OSC Q
RTCT
CLK
SERIAL-TO-PARALLEL SHIFT REGISTER
DIN D0 D1 D2 D3 D4 D5 D6 D7 DOUT
OUTPUT LATCHES
POWER-ON
LE D0 D1 D2 D3 D4 D5 D6 D7 RESET V+
OE
V+
CONSTANT-CURRENT SINK
THERMAL CURRENT
D0 D1 D2 D3 D4 D5 D6 D7 REFERENCE SET
SHUTDOWN
PGND
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
______________________________________________________________________________________ 13
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
OUT is a push-pull output with the on-resistance of the
MAX16807/MAX16808
V+
pMOS typically 3.5Ω and the on-resistance of the
nMOS typically 4.5Ω. The driver can source 2A and
sink 1A typically. This allows for the MAX16807/
MAX16808 to quickly turn on and off high gate-charge
68W/L W/L
OUT_ MOSFETs. Bypass VCC with one or more 0.1µF ceramic
1.23 capacitors to AGND, placed close to the VCC pin. The
1 23V REST average current sourced to drive the external MOSFET
995R
depends on the total gate charge (QG) and operating
frequency of the converter. The power dissipation in the
MAX16807/MAX16808 is a function of the average out-
put drive current (IDRIVE). Use the following equation to
R
calculate the power dissipation in the device due to
IDRIVE:
SET PGND
IDRIVE = (QG x fSW)
PD = (IDRIVE + ICC) x VCC
Figure 1c. OUT_ Driver Internal Diagram where I CC is the operating supply current. See the
Typical Operating Characteristics for the operating
supply current at a given frequency.
Switch-Mode Controller
Error Amplifier
Current-Mode Control Loop The MAX16807/MAX16808 include an internal error
The advantages of current-mode control over voltage- amplifier. The inverting input is at FB and the noninvert-
mode control are twofold. First, there is the feed-for- ing input is internally connected to a 2.5V reference.
ward characteristic brought on by the controller’s ability Set the output voltage using a resistive divider between
to adjust for variations in the input voltage on a cycle- output of the converter VOUT, FB, and AGND. Use the
by-cycle basis. Second, the stability requirements of following formula to set the output voltage:
the current-mode controller are reduced to that of a sin-
gle pole system unlike the double pole in the voltage-
⎛ R1 ⎞
mode control scheme. The MAX16807/MAX16808 use VOUT = ⎜1 + ⎟ x VFB
a current-mode control loop where the output of the ⎝ R2 ⎠
error amplifier is compared to the current-sense voltage
(VCS). When the current-sense signal is lower than the where VFB = 2.5V.
inverting input of the CPWM comparator, the output of Oscillator
the comparator is low and the switch is turned on at The oscillator frequency is programmable using an
each clock pulse. When the current-sense signal is external capacitor and a resistor at RTCT (see RT and
higher than the inverting input of the CPWM compara- CT in the Typical Operating Circuits). RT is connected
tor, the output is high and the switch is turned off. from RTCT to the 5V reference (REF), and CT is con-
Undervoltage Lockout (UVLO) nected from RTCT to AGND. REF charges CT through
The turn-on supply voltage for the MAX16807/ RT until its voltage reaches 2.8V. CT then discharges
MAX16808 is 8.4V (typ). Once VCC reaches 8.4V, the through an 8.3mA internal current sink until CT’s voltage
reference powers up. There is a 0.8V of hysteresis from reaches 1.1V, at which time CT is allowed to charge
the turn-on voltage to the UVLO threshold. Once VCC through RT again. The oscillator’s period is the sum of
reaches 8.4V, the MAX16807/MAX16808 operate with the charge and discharge times of CT. Calculate the
VCC down to 7.6V (typ). Once VCC goes below 7.6V, charge time as follows:
the device is in UVLO. When in UVLO, the quiescent tC = 0.57 x RT x CT
supply current into VCC falls back to 32µA (typ), and where t C is in seconds, R T in ohms (Ω), and C T in
OUT and REF are pulled low. Farads (F).
MOSFET Driver The discharge time is then:
OUT drives an external n-channel MOSFET and swings tD = (RT x CT x 1000) / [(4.88 x RT) - (1.8 x 1000)]
from AGND to VCC. Ensure that VCC remains below the
absolute maximum VGS rating of the external MOSFET.
14 ______________________________________________________________________________________
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
where t D is in seconds, R T in ohms (Ω), and C T in
MAX16807/MAX16808
Farads (F). VCS
RCS =
The oscillator frequency is then: IP − P
VN VOUT
L1 C1
D
COUT
Q L2
R1 LEDs
CC2
RCS
CC1 RC1
R2
VCC FB
CN
3V TO 5 5V
V+
CBYP
MAX16807
PGND OUT0
MAX16808
OUT1
DIN OUT2
LE OUT3
OUT4
EXTERNAL OUT5
CLK
CLOCK INPUT
DOUT OUT6
EXTERNAL
OE OUT7
DIM INPUT
SET
REF RTCT
RT
RSET
CREF CT
______________________________________________________________________________________ 15
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
LED Driver LE is the latch enable input of the MAX16807/
MAX16807/MAX16808
H H R0 R1 … Rn-2 Rn-1
L L R0 R1 … Rn-2 Rn-1
X R0 R1 R2 … Rn-1 Rn
X X X … X X L R0 R1 R2 … Rn-1 Rn
P0 P1 P2 … Pn-1 Pn H P0 P1 P2 … Pn-1 Pn L P0 P1 P2 … Pn-1 Pn
X X X … X X H L L L … L L
L = Low Logic Level
H = High Logic Level
X = Don’t Care
P = Present State (Shift Register)
R = Previous State (Latched)
16 ______________________________________________________________________________________
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
MAX16807/MAX16808
LE tLW
tCL tCH tLS
tCP
CLK
tDH
tDS
DIN D7 D0
tDO
DOUT D7
tOEW
OE
tOEF tOER
80%
OUT_
20%
tf tr
LE
CLK
tCRR CLK
DOUT D7 D6 D5 D4
OUT_
______________________________________________________________________________________ 17
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
data have been clocked into the shift register(s), and LED Dimming
MAX16807/MAX16808
18 ______________________________________________________________________________________
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
Pin Configuration Chip Information
MAX16807/MAX16808
PROCESS: BiCMOS
TOP VIEW
+
N.C. 1 28 N.C.
AGND 2 27 RTCT
OUT 3 26 CS
VCC 4 MAX16807 25 FB
MAX16808
REF 5 24 COMP
OUT4 6 23 OUT3
OUT5 7 22 OUT2
OUT6 8 21 OUT1
OUT7 9 20 OUT0
OE 10 19 LE
DOUT 11 18 CLK
SET 12 17 DIN
N.C. 13 16 PGND
V+ 14 15 PGND
TSSOP-EP
______________________________________________________________________________________ 19
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
Typical Operating Circuits (continued)
MAX16807/MAX16808
VIN VOUT
L D
COUT
Q
R1 LEDs
CC2
RCS
CC1 RC1
R2
VCC FB
CIN
3V TO 5 5V
V+
CBYP OUT0
PGND OUT1
MAX16807 OUT2
MAX16808
OUT3
OUT4
SCLK CLK OUT5
MOSI DIN OUT6
µC MISO DOUT OUT7
LOAD LE
ENABLE OE OPERATION WITH MICROCONTROLLER
SET
REF RTCT
RSET RT
CREF CT
20 ______________________________________________________________________________________
Integrated 8-Channel LED Drivers with
Switch-Mode Boost and SEPIC Controller
Package Information
MAX16807/MAX16808
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 21
© 2006 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.