osrost2024 Removal and Instalaton (Cynder Head Assembly) ALLDATA Repair
2015 Nissan-Datsun Sentra L4-1.8L (MRA8DE)
Vehicle > Engine, Cooling and Exhaust > Engine > Cylinder Head Assembly > Service and Repair > Removal and
Replacement
REMOVAL AND INSTALLATION
CYLINDER HEAD
Removal and Installation
REMOVAL
1 Release fuel pressure, Refer to "Work Procedure” See: Fuel Pressure > Component Tests and General
Diagnostics > Work Procedure.
2.0rain engine coolant and engine oil. Refer to "Changing Engine Coolant” See: Coolant > Procedures > Changing
Engine Coolant (for Coolant) and "Draining" See: Engine Oil > Procedures > Draining (for Oil).
3.Remove fan motor and shroud assembly. Refer to "Component" See: Radiator Cooling Fan > Removal and
Replacement > Component.
4.Remove the exhaust manifold, Refer to "Exploded View" See: Exhaust Manifold > Removal and Replacement >
Exploded View
5.Remove the intake manifold. Refer to "Exploded View" See: Intake Manifold > Removal and Replacement >
Exploded View.
6.Remove the fuel injector and fuel tube assembly. Refer to "Exploded View" See: Fuel Rail > Removal and
Replacement > Exploded View.
7.Remove the water outlet. Refer to "Exploded View" See: Coolant Outlet > Removal and Replacement > Exploded
View.
8 Remove the rocker cover. Refer to "Exploded View” See: Valve Cover > Removal and Replacement > Exploded
View.
9,Remove the front cover and timing chain. Refer to “Exploded View" See: Timing Chain > Removal and
Replacement > Exploded View.
10.Remove the camshaft. Refer to "Exploded View” See: Camshaft, Engine > Removal and Replacement >
Exploded View.
11.Remove cylinder head
htpssimy alléata.comrepalrrepalartcle!5511Sicomponent/6Sitypel401nonstandardi68797S!selRetLinktrve 7si06:2021 Removal and Installation (Cylinder Head Assembly)- ALLDATA Repair
- Loosen cylinder head bolts in the reverse order as shown.
White arrow indicates : Engine front
12.Remove cylinder head gasket.
INSTALLATION
install cylinder head gasket
CAUTION:
Do not reuse cylinder head gasket.
2.Install cylinder head, and tighten cylinder head bolts in order as shown using Tool (A).
- Clean threads and seating surfaces of bolts.
- Apply new engine oil to threads and seating surface of bolts.
CAUTION:
- If cylinder head bolts are reused, check their outer diameters before installation. Refer to “Inspection” See:
Cylinder Head Assembly > Overhaul > Inspection.
htpssimy alléata.comrepalrrepalartcle!5511Sicomponent/6Sitypel401nonstandardi68797S!selRetLinktrve
24si06:2021 Removal and Installation (Cylinder Head Assembly)- ALLDATA Repair
- Check and confirm the tightening angle by using Tool (A).
Do not judge by visual inspection without the tool.
Tool number (A): KV10112100 (BT-8653-A)
Step 1; 40.0 Nm (4.1 kg-m, 30 ft-Ib)
Step 2: 100 clockwise in order
Step 3: 0 Nm (0 kg-m, 0 ft-lb)
Step 4: 40.0 Nm (4.1 kg-m, 30 ft-Ib)
Step 5: 100 clockwise in order
Step 6: 100 clockwise in order
White arrow indicates : Engine front
3 Installation of remaining components is in the reverse order of removal.
htpssimy alléata.comrepalrrepalartcle!5511Sicomponent/6Sitypel401nonstandardi68797S!selRetLinktrve
a4si06:2021 Removal and Installation (Cylinder Head Assembly)- ALLDATA Repair
htpssimy alléata.comrepalrrepalartcle!5511Sicomponent/6Sitypel401nonstandardi68797S!selRetLinktrve
4a