Professional Documents
Culture Documents
schneider-electric.com
Schneider Electric policy is one of continuous technological innovation and the Company therefore reserves
the right to amend any data herein without prior notice. The images shown in this catalog are for descriptive
purposes only. They may therefore differ from specific models that are selected. Some of the features described may
be available only for some models or configurations. Please refer to the specific technical literature for further details.
Uniflair ...............................................................................................................Page 6
Uniflair benefits..................................................................................................Page 8
Availability
Continuous operation to safeguard
the customer’s business.
Energy saving
Technological excellence
for efficient performance.
Data center
Industry
Perfect for racked and nonracked IT loads, these products meet the diverse
requirements of any data center environment. These intelligent units monitor
the status of components and environmental parameters to ensure correct
functionality during all modes of operation. When combined with hot-or-cold-aisle
containment solutions, Uniflair products can further improve efficiency and achieve
higher densities.
CapEx
recent increases in the ASHRAE recommended data
center operation temperature ranges
• Optimum design on heat exchangers to reach SHR
(sensible heat ratio) close to 1 and so to provide CapEx optimization
more useful (sensible) cooling capacity in the can be achieved by
same footprint. using a cooling infra-
• Optimized management system to have all structure that is simply
Schneider Electric cooling resources connected implemented and
for energy maximization based on real, adapted to changing
instantaneous load conditions. site requirements.
A fundamental requirement for each data center is to • adapt to a wide range of supervision and network
guarantee continuous operation. languages and protocols
Reliability is achieved thanks to the design and • can easily interface with a wide range
implementation of cooling systems that are intrinsically of BMS systems
reliable and incorporate an appropriate level of
DCIM
redundancy.
Solutions
considerations, such as a dual source of cooling and
electrical power.
In case of power failure, capacitors release the stored Alternatively, the unit can adjust the airflow based on a
energy until it is not exhausted, the minimum time combination of the heat load in the room (related to the
ensured with the Ultracapacitor fully charged is two speed of inverter driven compressor) and the airflow
minutes. When power is reset, the capacitors start regulation from minimum to maximum.
re-charging.
MAX
MIN MAX
Cooling capacity
160 +39%
Cooling capacity [kW]
120 +68%
+112%
80
40
0
Frame 5 Frame 6 Frame 7
160 +39%
Cooling capacity [kW]
Direct Expansion 40
12 Life is On | Schneider Electric
0
Frame 5 Frame 6 Frame 7
Active Flow Controller (AFC)
Maintaining correct pressurization of the floor space is
a key factor to ensure that the cooling system operates
with maximum efficiency and that cool air is available
where needed. This process must be guaranteed for the
entire lifetime of a server room that may be upgraded
and changed over time.
25
-45% -50%
-45%
20 -40%
-24%
-35%
15 -30%
-25%
10 -20%
-15%
0%
5 -10%
-5%
0 0%
Active Floor
Active Floor is a flexible and modular system for cooling
data centres with medium- and high-density loads.
Integrated within a modular access floor in front of the
intake section of the rack, the Active Floor fits exactly
into a modular access floor panel measuring 600 mm
x 600 mm. The cold air produced by the Close Control
perimeter units is directly channeled to the source of the
thermal load thanks to the advanced adjustment of the
direction of the airflow.
Beijing -30%
Mumbai -21%
(*) Data calculated comparing IDAV2922 and TDAV3342 for 100 kW net sensible 37° return air
0
0 20 40 60 80 100
Speed (rps)
12
+11%
+10%
OOP improvement (%)
6 +6%
+4%
3
+1%
0
35˚C 30˚C 25˚C 20˚C 15˚C
Non-return valve
The non-return valve is integrated in the compressors of
LDAV3822 while on the other LDAV units it’s installed in
the refrigerant circuit. The scope of the non-return valve
is to avoid the refrigerant migration from high-pressure
to low-pressure side after compressor is switched off.
-6.9%
-6.9%
-5.6%
-6.4%
-4.1%
Shanghai -17%
Sydney -23%
Johannesburg -26%
• Part of the range optimized for high water temperatures and discharge temperature control.
• Part of the range optimized for traditional water temperatures.
The optimized design for high Delta T enables to have less consumption on yearly base compared to a unit not optimized.
-22%
-35%
• +43% cooling capacity in the box with the same power consumption compared to traditional working conditions
• +29% cooling capacity compared to traditional design at the same conditions
Cooling capacity
Cooling capacity
Lagacy Lagacy
Gen 2 Gen 2 Not Optimized Not Optimized
Gen 2 Gen 2
How it works
6.0 25
Water Temperature (˚C)
5.0
Energy Efficiency (%)
20
4.0
15
3.0
10
2.0
5
1.0 EER
0 0 Operating Water Temperature
Min Medium Medium Max
Load Load Load Load
Number of units ON
+28% +39%
+20% +42%
+0% +0%
EER
EER
Microchannel coils
The new generation of external condensers can
be equipped with microchannel condensing coils
to reduce the refrigerant charge and minimize
air-side pressure drops.
Uniflair AM Uniflair LE
Water cooled
IUWV (Upflow)
IDWV (Downflow)
IXWV (Underfloor)
Energy Saving
IUEV (Upflow)
IDEV (Downflow)
IXEV (Underfloor)
*V suffix = Electronically Commuted (EC) motor fans;C/ R suffix = backward-curved fans with asynchronous motor;
Uniflair AM
SDAC – SUAC
Range
Cooling capacity: 5 ÷ 20 kW
Refrigerant R-410A
Available versions
• Downflow (SDAC)
• Upflow (SUAC) with bottom, front, and rear suction
Standard features
• Advanced microprocessor control system is • Total front access is available for unit maintenance.
included with local or remote user terminal. • Electrical panel is situated in a compartment
• The units are equipped with forward-curved fans separated from the airflow and complies with
and directly coupled asynchronous motor. the Machinery Directive 2006/42/EC (MD)
• The structure of the unit is characterized by directive and related standards.
a self-supporting frame in galvanized steel with • Microprocessor control system includes:
panels. The external panels are coated with - Local user terminal with external accessibility
RAL9003 epoxy-polyester paint and internally - Integrated LAN card for local network connection
lined with heat- and sound-proofing insulation. of a group of CRACs
• The cooling coil is designed for an elevated SHR - Rotation and active stand-by management
and reduced pressure drops in the air section. - Free contact for general alarm and two
The coil is made from copper tubes mechanically for addressable alarms
expanded on aluminum fins, complete with - Remote on/off switch
a hydrophilic treatment.
- Ability to interface with modbus protocol
• Uniflair AM units are in conformity with the following directly on RS485 serial card
directives: Machinery Directive 2006/42/EC (MD),
- Ability to interface with main external communication
Electromagnetic compatibility Directive 2014/30/EU
protocols: BACnetTM, Lonworks, Trend, Metasys,
(EMC), Pressure equipment Directive 2014/68/EU
TCP/IP, SNMP, and StruxureWareTM platform
(PED), Regulation (EU) No 517/2014 on fluorinated
greenhouse gases (F-GAS).
• High-efficiency, EU4-pleated air filters are housed
in a metal frame and equipped with a dirty filter
differential pressure switch and low airflow differential
pressure switch.
Uniflair AM
SDAV – SUAV
Range
Cooling capacity: 5 ÷ 20 kW
Refrigerant R-410A
EC fans
Available versions
• Downflow (SDAV)
• Upflow (SUAV) with bottom, front, and rear suction
Standard features
• Advanced microprocessor control system is • Total front access is available for unit maintenance.
included with local or remote user terminal. • Electrical panel is situated in a compartment
• The units are equipped with EC fans for separate from the airflow and in compliance with
efficiency maximization. the Machinery Directive 2006/42/EC (MD) directive
• The structure of the unit is characterized by and related standards.
a self-supporting frame in galvanized steel with • Microprocessor control system includes:
panels. The external panels are coated with - Local user terminal with external accessibility
RAL9003 epoxy-polyester paint and internally - Integrated LAN card for local network connection
lined with heat- and sound-proofing insulation. of a group of CRACs
• The cooling coil is designed for an elevated SHR - Rotation and active stand-by management
and reduced pressure drops in the air section. - Free contact for general alarm and two for
The coil is made from copper tubes mechanically addressable alarms
expanded on aluminum fins, complete with - Remote on/off switch
a hydrophilic treatment.
- Ability to interface with modbus protocol
• Uniflair AM units are in conformity with the following directly on RS485 serial card
directives: Machinery Directive 2006/42/EC (MD),
- Ability to interface with main external communication
Electromagnetic compatibility Directive 2014/30/EU
protocols: BACnet, Lonworks, Trend, Metasys,
(EMC), Pressure equipment Directive 2014/68/EU
TCP/IP, SNMP, and StruxureWare platform
(PED), Regulation (EU) No 517/2014 on fluorinated
greenhouse gases (F-GAS).
• High-efficiency, EU4-pleated air filters are housed
in a metal frame and equipped with a dirty filter
differential pressure switch and low airflow differential
pressure switch.
Uniflair AM
SDWC – SUWC
Range
Cooling capacity: 5 ÷ 20 kW
Refrigerant R-410A
Available versions
• Downflow (SDWC)
• Upflow (SUWC) with bottom, front, and rear suction
Standard features
• Advanced microprocessor control system is • Total front access is available for unit maintenance.
included with local or remote user terminal. • The electrical panel is situated in a compartment separated
• The units are equipped with forward-curved fans from the airflow and complies with the Machinery Directive
and directly coupled asynchronous motor. 2006/42/EC (MD) directive and related standards.
• The structure of the unit is characterized by • Microprocessor control system includes:
a self-supporting frame in galvanized steel with - Local user terminal with external accessibility
panels. The external panels are coated with - Integrated LAN card for local network connection
RAL9003 epoxy-polyester paint and internally of a group of CRACs
lined with heat- and sound-proofing insulation. - Rotation and active stand-by management
• The cooling coil is designed for an elevated SHR - Free contact for general and two for addressable alarms
and reduced pressure drops in the air section. - Remote on/off switch
The coil is made from copper tubes mechanically
- Ability to interface with modbus protocol
expanded on aluminum fins, complete with
directly on RS485 serial card
a hydrophilic treatment.
- Ability to interface with main external communication
• Uniflair AM units are in conformity with the following
protocols: BACnet,Lonworks, Trend, Metasys,
directives: Machinery Directive 2006/42/EC (MD),
TCP/IP, SNMP, and StruxureWare platform
Electromagnetic compatibility Directive 2014/30/EU
(EMC), Pressure equipment Directive 2014/68/EU
(PED), Regulation (EU) No 517/2014 on fluorinated
greenhouse gases (F-GAS).
• High-efficiency, EU4-pleated air filters are housed
in a metal frame and equipped with a dirty filter
differential pressure switch and low airflow differential
pressure switch.
Uniflair AM
SDWV – SUWV
Range
Cooling capacity: 5 ÷ 20 kW
Refrigerant R-410A
EC fans
Available versions
• Downflow (SDWV)
• Upflow (SUWV) with bottom, front, and rear suction
Standard features
• Advanced microprocessor control system is • Total front access is available for unit maintenance.
included with local or remote user terminal. • The electrical panel is situated in a compartment
• The units are equipped with EC fans for separated from the airflow and complies with
efficiency maximization. the Machinery Directive 2006/42/EC (MD) directive
• The structure of the unit is characterized by and related standards.
a self-supporting frame in galvanized steel with • Microprocessor control system includes:
panels. The external panels are coated with - Local user terminal with external accessibility
RAL9003 epoxy-polyester paint and internally - Integrated LAN card for local network connection
lined with heat- and sound-proofing insulation. of a group of CRACs
• The cooling coil is designed for an elevated SHR - Rotation and active stand-by management
and reduced pressure drops in the air section. - Free contact for general and two for addressable alarms
The coil is made from copper tubes mechanically - Remote on/off switch
expanded on aluminum fins, complete with - Ability to interface with modbus protocol
a hydrophilic treatment. directly on RS485 serial card
• Uniflair AM units are in conformity with the following - Ability to interface with main external communication
directives: Machinery Directive 2006/42/EC (MD), protocols: BACnet, Lonworks, Trend, Metasys,
Electromagnetic compatibility Directive 2014/30/EU TCP/IP, SNMP, and StruxureWare platform
(EMC), Pressure equipment Directive 2014/68/EU
(PED), Regulation (EU) No 517/2014 on fluorinated
greenhouse gases (F-GAS).
• High-efficiency, EU4-pleated air filters are housed
in a metal frame and equipped with a dirty filter
differential pressure switch and low airflow differential
pressure switch.
Uniflair AM
SDCC – SUCC
Range
Cooling capacity: 5 ÷ 20 kW
Refrigerant CW
Available versions
• Downflow (SDCC)
• Upflow (SUCC) with bottom, front, and rear suction
Standard features
• Advanced microprocessor control system is • Total front access is available for unit maintenance.
available with local or remote user terminal. • The electrical panel is situated in a compartment
• The units are equipped with forward-curved fans separated from the airflow and complies
with directly coupled asynchronous motor. with the Machinery Directive 2006/42/EC (MD),
• The structure of the unit is characterized by Regulation (EU) No 517/2014 on fluorinated greenhouse
a self-supporting frame in galvanized steel gases (F-GAS) directive and related standards.
with panels. The external panels are coated with • Microprocessor control system includes:
RAL9003 epoxy-polyester paint and internally - Local user terminal with external accessibility
lined with heat- and sound-proofing insulation. - Integrated LAN card for local network connection of
• The unit can be selected with a two-way a group of CRACs
or three-way valve and an actuator - Rotation and active stand-by management
integrated with the microprocessor. - Free contact for general and two for addressable alarms
• The cooling coil is designed for an elevated SHR - Remote on/off switch
and reduced pressure drops in the air section. - Ability to interface with modbus protocol
The coil is made from copper tubes mechanically directly on RS485 serial card
expanded on aluminum fins, complete with
- Ability to interface with main external communication
a hydrophilic treatment.
protocols: BACnet, Lonworks, Trend, Metasys,TCP/IP,
• High-efficiency, EU4-pleated air filters are housed SNMP, and StruxureWare platform
in a metal frame and equipped with a dirty filter
differential pressure switch and low airflow
differential pressure switch.
Uniflair AM
SDCV – SUCV
Range
Cooling capacity: 5 ÷ 20 kW
Refrigerant CW
EC fans
Available versions
• Downflow (SDCV)
• Upflow (SUCV) with bottom, front, and rear suction
Standard features
• Advanced microprocessor control system is • Total front access is included for unit maintenance.
available with local or remote user terminal. • The electrical panel is situated in a compartment separated
• The units are equipped with EC fans from the airflow and complies with the Machinery Directive
for efficiency maximization. 2006/42/EC (MD), Regulation (EU) No 517/2014 on fluorinated
• The structure of the unit is characterized by greenhouse gases (F-GAS) directive and related standards.
a self-supporting frame in galvanized steel with • Microprocessor control system includes:
panels. The external panels are coated with - Local user terminal with external accessibility
RAL9003 epoxy-polyester paint and internally - Integrated LAN card for local network connection
lined with heat- and sound-proofing insulation. of a group of CRACs
• The unit can be selected with a two-way - Rotation and active stand-by management
or three-way valve and an actuator - Free contact for general and two for addressable alarms
integrated with the microprocessor. - Remote on/off switch
• The cooling coil is designed for an elevated SHR - Ability to interface with modbus protocol
and reduced pressure drops in the air section. directly on RS485 serial card
The coil is made from copper tubes mechanically
- Ability to interface with main external communication protocols:
expanded on aluminum fins, complete with
BACnet, Lonworks, Trend, Metasys,
a hydrophilic treatment.
TCP/IP, SNMP, and StruxureWare platform
• High-efficiency, EU4-pleated air filters are housed
in a metal frame and equipped with a dirty filter
differential pressure switch and low airflow
differential pressure switch.
Uniflair LE
LDCV – LUCV
Range
Cooling capacity: 20 ÷ 170 kW
Refrigerant CW
EC fans
Available versions
• Downflow (LDCV)
• Upflow (LUCV)
Standard features
• Advanced microprocessor control system UG50 with • A low airflow differential pressure alarm switch is included.
touch-screen human interface is included. • Single coil version with one chilled water circuit.
• The units are equipped with the latest generation • CW inlet temperature measurement is integrated in the microprocessor.
Radical EC fans for efficiency maximization. Impellers • Integrated discharge temperature control and room moisture control.
are made of high-tech compound material with • Zinc-free CW circuit.
optimized flow control, combined with highly efficient • Full frontal accessibility is available for maintenance.
GreenTech EC motors. These fans are designed to
• Electric panel conforms to Machinery Directive 2006/42/EC (MD) and
have easier serviceability with quick removal kit.
Electromagnetic compatibility Directive 2014/30/EU (EMC).
• The structure of the unit is characterized by a self-
• Phase sequence control.
supporting frame in galvanized steel with panels.
• Microprocessor control system includes:
The external panels are coated with RAL9003 epoxy-
- Adjustable fan speed meets energy-saving and load-sharing logics
polyester paint and internally lined with heat- and
- 7-inch, touch-screen LCD display interface
sound-proofing insulation. The internal panels are
featured by captive screws. - Integration with Uniflair Chillers for optimized management logics
• The unit can be selected with a two-way or three- - Integrated LAN card for local network connection of a group of CRACs
way valve and an actuator integrated with the - Rotation and active stand-by management
microprocessor. The actuator is available in two - Free contact for general and two for addressable alarms
versions: basic and premium. - Remote on/off switch
• The cooling coil is designed for an elevated SHR and - Integrated RS485 serial card for direct connection to
reduced pressure drops in the air section. The coil is external BMS (modbus)
made from copper tubes mechanically expanded on - Integrated TCP/IP serial card for BMS connection
aluminum fins, complete with a hydrophilic treatment. - Clock card integrated in the unit
• High-efficiency, EU4-pleated air filters are housed in a - USB integrated in the display interface
metal frame and equipped with a dirty filter - Ability to interface with main external communication protocols: BACnet,
differential pressure switch and low airflow Lonworks, Trend, Metasys, TCP/IP, SNMP, and StruxureWare platform
differential pressure switch.
Uniflair LE
HDCV
Range
Cooling capacity: 30 ÷ 250 kW
Refrigerant CW
EC fans
Available versions
• Downflow Single Coil
• Downflow Dual Coil
4
1 Data refer to nominal
HDCV MODEL 0800A1 HT 1400A1 HT 1800A1 HT 2900A1 HT 4600A1 HT 5300A1 HT 5500A1 HT
conditions: Room at
Fan type EC Backward-curved centrifugal motor fan
36 °C-30% RH water
Version High temperature temperature 20/30 °C,
Power supply V/ph/Hz 400/3/50Hz fan module installed
Fans Nr. 1 1 2 2 3 4 4 under a 900 mm raised
Airflow m3/h 7400 11000 17000 25500 28200 33700 36400 floor, and glycol 20%.
Net sensible cooling capacity4 kW 28.4 42.0 64.0 97.7 109.5 130.7 143.2
5
Includes fan module.
DIMENSIONS
Height5 mm 2510 2510 2510 2510 2510 2510 2510
Length mm 1010 1310 1720 2170 2570 3100 3405
Depth mm 865 865 865 865 865 865 865
Construction options
Unit with fan plenum installed
under the raised floor.
Uniflair LE
TDAR – TUAR
Range
Cooling capacity: 20 ÷ 100 kW
Refrigerant R-410A
Available versions
• Downflow (TDAR)
• Upflow (TUAR)
DIMENSIONS
Height mm 1960 1960 1960 1960 1960 1960 1960
Length mm 1010 1010 1310 1310 1310 1310 1310
Depth mm 750 750 865 865 865 865 865
TDAR – TUAR MODEL 1022A 1121A 1122A 1321A 1322A 1422A 1622A
Fans nr. 1 1 2 2 2 2 2
Airflow m3/h 7933 12267 12267 12267 12267 16406 16406
N° of compressors 2 2 2 2 2 2 2
Refrigerating circuits 2 1 2 1 2 2 2
Gross total cooling
kW 36,9 37,8 37,9 48,0 47,7 51,6 57,5
capacity1,2
Gross sensible cooling
kW 28,0 36,8 36,2 39,3 38,0 51,0 56,8
capacity1,2
DIMENSIONS
Height mm 1960 1960 1960 1960 1960 1960 1960
Length mm 1010 1720 1720 1720 1720 2170 2170
Depth mm 865 865 865 865 865 865 865
TDAR – TUAR MODEL 1822A 2222A3 2242A3 2522A3 2542A3 2842A3 3342A3
Fans nr. 2 3 3 3 3 3 3
Airflow m3/h 16406 21656 21656 21656 22046 22055 22055
N° of compressors 2 2 4 2 4 4 4
Refrigerating circuits 2 2 2 2 2 2 2
Gross total cooling
kW 63,9 75,1 81,2 86,7 88,1 97,4 107,6
capacity1,2
Gross sensible cooling
kW 57,3 75,1 80,3 83,3 84,5 90,8 92,9
capacity1,2
DIMENSIONS
Height mm 1960 2150 2150 2150 2150 2150 2150
Length mm 2170 2580 2580 2580 2580 2580 2580
Depth mm 865 865 865 865 865 865 865
TUAR MODEL 2222A 2242A 2522A 2542A 2842A 3342A
Fans nr. 3 3 3 3 3 3
Airflow m3/h 22154 22154 23467 23467 23068 23068
N° of compressors 2 4 2 4 4 4
Refrigerating circuits 2 2 2 2 2 2
Gross total cooling
kW 75,4 82,7 86,5 87,5 97,9 108,2
capacity1,2
Gross sensible cooling
kW 75,4 81,8 85,5 86,4 93,8 95,6
capacity1,2
DIMENSIONS
Height mm 1960 1960 1960 1960 1960 1960
Length mm 2580 2580 2580 2580 2580 2580
Depth mm 865 865 865 865 865 865
Uniflair LE
TDAV – TUAV
Range
Cooling capacity: 20 ÷ 100 kW
Refrigerant R-410A
EC fans
Available versions
• Downflow (TDAV)
• Upflow (TUAV)
Uniflair LE
LDAV
Range
Cooling capacity: 60 ÷ 140 kW
Fixed speed compressors
Refrigerant R-410A
EC fans
Available versions
• Downflow (LDAV)
Standard features
• Downflow configuration with bottom or front discharge • New generation of hermetic scroll compressor with
and suction from the top. Intermediate Discharge Valves (IDVs), built-in thermal
• Metal structural frame and inside part made with protection and anti-vibration feet
hot-dip zinc-plated sheet steel • Refrigerant R410A
• External panels coated with RAL9003 epoxy-polyester • Electronic Expansion Valve (EEV) to provide accurate
paint and internally lined with heat- and sound- control of the refrigerant superheat ensuring high
proofing insulation to class 1 according to Class energy efficiency also at low external temperatures.
B1 according to DIN 4102, BS 476 part 7,VO • Electrical panel complying with Machinery Directive
according to UL94, ASTM E84, class M1 2006/42/EC (MD) and Electromagnetic compatibility
according to NFP92-501 Directive 2014/30/EU (EMC), Regulation (EU)
• Internal panels for shutting-off the compartments No 517/2014 on fluorinated greenhouse gases (F-GAS),
affected by the airflow, made with hot-dip zinc-plated housed- in a compartment isolated from the airflow and
sheet steel and captive screws including 24V control circuit transformer, metal isolating
• High efficiency EU4 pleated air filters are contained screen for protection from live components, mains
in a metal frame and equipped with a dirty filter switch, thermomagnetic circuit-breakers, terminal board
differential pressure switch and a low airflow for no-voltage signal and control contacts.
differential pressure switch. The filters are housed • 7-inch. IT Touch Screen display interface that allows to
in a dedicated plenum box. set operating parameters, monitor the trend
• The units are equipped with the latest generation of the main working parameters, and read any
Radical EC Fans for efficiency maximization. Impellers alarm messages.
are made of high-tech compound material with • Schneider Electric IT J-Controller (J5 18 DIN),
optimized flow control, combined with highly efficient complying with Machinery Directive 2006/42/EC (MD)
GreenTech EC motors. These fans are designed to and Electromagnetic compatibility Directive 2014/30/
have easier serviceability with quick removability kit. EU (EMC), Regulation (EU) No 517/2014 on fluorinated
• Low airflow differential pressure switch greenhouse gases (F-GAS), where are connected
analogical and digital inputs necessary for control of
• Cooling coil, mounted upstream of the fans,
the unit.
constructed of copper tubes expanded into
hydrophilic aluminum fins, complete with stainless • Control software design to provide a highly accurate
steel tray and a flexible condensate drain hose real-time control of room conditions and the complete
unit management such as:
• Double refrigerant circuit each equipped with a fixed-
speed scroll compressor. - electronic expansion valve complete management
• Refrigerant circuits complying with Pressure - advanced interactivity with the
Equipment Directive 2014/68/EU (PED) including: installation environment
liquid refrigerant receiver, filter-dryer and liquid sight - dehumidification operating mode managed by
glass, electronic expansion valve, high-pressure means of EEV with devised algorithm which
pressostats with manual reset. maintains constant air flow
- double set-point with digital input selection
- emergency operation
DIMENSIONS
Height mm 2150 2150 2150 2150
Length mm 2082 2650 2650 2650
Depth mm 900 900 900 900
Uniflair LE
TDWR – TUWR
Range
Cooling capacity: 20 ÷ 100 kW
Refrigerant R-410A
Available versions
• Downflow (TDWR)
• Upflow (TUWR)
Standard features
• Advanced microprocessor control system is available • The Uniflair LE range offers the possibility to select units
with local or remote user terminal. equipped with two compressors (tandem) for each circuit,
• The units are equipped with backward-curved fans which grants better efficiency and regulation capacity at
and directly coupled asynchronous motor. partial loads (models with the **21 or **42 suffix).
• The structure of the unit is characterized • Total front access is available for unit maintenance.
by a self-supporting frame in galvanized steel • The electrical panel is situated in a compartment separated
with panels. The external panels are coated from the airflow and complies with the Machinery Directive
with RAL9003 epoxy-polyester paint and internally 2006/42/EC (MD) and related standards.
lined with heat- and sound-proofing insulation. • Microprocessor control system includes:
• Electronic expansion valve is controlled - Integrated management of the EEV
by the microprocessor and a dedicated software and refrigerating circuit parameters
that increases the precision of the cooling - Local user terminal with external accessibility
and the energy efficiency of the cooling cycle. - Integrated LAN card for local network connection of
• The cooling coil is designed for an elevated SHR a group of CRACs
and reduced pressure drops in the air section. - Rotation and active stand-by management
The coil is made from copper tubes mechanically - Free contact for general and two for addressable alarms
expanded on aluminum fins, complete with
- Remote on/off switch
a hydrophilic treatment.
- Ability to interface with modbus protocol directly
• Internal water-cooled condenser braze is welded
on RS485 serial card
and made of AISI 304 stainless steel.
- Ability to interface with main external communication
• Uniflair LE units meet the following directives:
protocols: BACnet, Lonworks, Trend, Metasys, TCP/ IP,
Machinery Directive 2006/42/EC (MD),
SNMP, and StruxureWare platform
Electromagnetic compatibility Directive 2014/30/EU
(EMC), Pressure equipment Directive 2014/68/EU
(PED), Regulation (EU) No 517/2014 on fluorinated
greenhouse gases (F-GAS).
• High-efficiency, EU4-pleated air filters are housed
in a metal frame and equipped with a dirty filter
differential pressure switch and low airflow differential
pressure switch.
DIMENSIONS
Uniflair LE
TDWV – TUWV
Range
Cooling capacity: 20 ÷ 100 kW
Refrigerant R-410A
EC fans
Available versions
• Downflow (TDWV)
• Upflow (TUWV)
Standard features
• Advanced microprocessor control system with • The Uniflair LE range offers the possibility to select units
a local or remote user terminal. equipped with two compressors (tandem) for each circuit,
• The units are equipped with EC fans for which grants better efficiency and regulation capacity at
efficiency maximization. partial loads (models with the **21 or **42 suffix).
• The structure of the unit is characterized by • Total front access is available for unit maintenance.
a self-supporting frame in galvanized steel • The electrical panel is situated in a compartment separated
with panels. The external panels are coated from the airflow and complies with the Machinery Directive
with RAL9003 epoxy-polyester paint and internally 2006/42/EC (MD) and related standards.
lined with heat- and sound-proofing insulation. • Microprocessor control system includes:
• Electronic expansion valve is controlled by - Integrated management of the EEV and refrigerating
the microprocessor and a dedicated software circuit parameters
that increases the precision of the cooling - Local user terminal with external accessibility
and the energy efficiency of the cooling cycle. - Integrated LAN card for local network connection
• The cooling coil is designed for an elevated SHR of a group of CRACs
and reduced pressure drops in the air section. - Rotation and active stand-by management
The coil is made from copper tubes mechanically - Free contact for general and two for addressable alarms
expanded on aluminum fins, complete with
- Remote on/off switch
a hydrophilic treatment.
- Ability to interface with modbus protocol directly
• Internal water-cooled condenser braze is welded
on RS485 serial card
and made of AISI 304 stainless steel.
- Ability to interface with main external communication
• Uniflair LE units meet the following directives:
protocols: BACnet, Lonworks, Trend, Metasys, TCP/IP,
Machinery Directive 2006/42/EC (MD),
SNMP, and StruxureWare platform
Electromagnetic compatibility Directive 2014/30/EU
(EMC), Pressure equipment Directive 2014/68/EU
(PED), Regulation (EU) No 517/2014 on fluorinated
greenhouse gases (F-GAS).
• High-efficiency, EU4-pleated air filters are housed
in a metal frame and equipped with a dirty filter
differential pressure switch and low airflow differential
pressure switch.
Uniflair LE
LDWV
Range
Cooling capacity: 60 ÷ 140 kW
Fixed speed compressors
Refrigerant R-410A
EC fans
Available versions
• Downflow (LDWV)
Standard features
• Downflow configuration with bottom or front discharge • New generation of hermetic scroll compressor with
and suction from the top. Intermediate Discharge Valves (IDVs), built-in thermal
• Metal structural frame and inside part made with hot- protection and anti-vibration feet
dip zinc-plated sheet steel • Refrigerant R410A
• External panels coated with RAL9003 epoxy-polyester • Electronic Expansion Valve (EEV) to provide accurate
paint and internally lined with heat- and sound- control of the refrigerant superheat ensuring high
proofing insulation to class 1 according to energy efficiency also at low external temperatures.
Class B1 according to DIN 4102, BS 476 part 7, • Electrical panel complying with Machinery Directive
VO according to UL94, ASTM E84, class M1 2006/42/EC (MD) and Electromagnetic compatibility
according to NFP92-501 Directive 2014/30/EU (EMC), housed- in a
• Internal panels for shutting-off the compartments compartment isolated from the airflow and including
affected by the airflow, made with hot-dip zinc-plated 24V control circuit transformer, metal isolating screen
sheet steel and captive screws for protection from live components, mains switch,
• High efficiency EU4 pleated air filters are contained thermomagnetic circuit-breakers, terminal board for
in a metal frame and equipped with a dirty filter no-voltage signal and control contacts.
differential pressure switch and a low airflow • 7-inch. IT Touch Screen display interface that allows
differential pressure switch. The filters are housed in a to set operating parameters, monitor the trend of
dedicated plenum box. the main working parameters, and read any alarm
• The units are equipped with the latest generation messages.
Radical EC Fans for efficiency maximization. Impellers • Schneider Electric IT J-Controller (J5 18 DIN),
are made of high-tech compound material with complying with Machinery Directive 2006/42/EC (MD)
optimized flow control, combined with highly efficient and Electromagnetic compatibility Directive 2014/30/
GreenTech EC motors. These fans are designed to EU (EMC), Regulation (EU) No 517/2014 on
have easier serviceability with quick removability kit. fluorinated greenhouse gases (F-GAS), where are
• Low airflow differential pressure switch connected analogical and digital inputs necessary for
control of the unit.
• Cooling coil, mounted upstream of the fans,
constructed of copper tubes expanded into • Control software design to provide a highly accurate
hydrophilic aluminum fins, complete with stainless real-time control of room conditions and the complete
steel tray and a flexible condensate drain hose unit management such as:
• Brazed plate water-cooled condenser made from - electronic expansion valve complete management
stainless steel. - advanced interactivity with the installation
• Double refrigerant circuit each equipped with a fixed- environment
speed scroll compressor. - dehumidification operating mode managed by
• Refrigerant circuits complying with Pressure means of EEV with devised algorithm which
equipment Directive 2014/68/EU (PED) including: maintains constant air flow
liquid refrigerant receiver, filter-dryer and liquid sight - double set-point with digital input selection
glass, electronic expansion valve, high-pressure - emergency operation
pressostats with manual reset.
DIMENSIONS
Height mm 2150 2150 2150 2150
Length mm 2082 2650 2650 2650
Depth mm 900 900 900 900
• The design of the IT J-Controller allows to physically • Standard, cleanable or low conductibility humidifier
isolate the internal connections from the external with immersed-electrodes for modulating steam
connections. The external connections on the upper production available as an option for units equipped
level offer a wide variety of accessibility options: with cooling and humidification configuration
- External CAN and Group CAN • Condensate drain pump
- Isolated 2-wire and 4-wire RS485 ports • Electrical heaters with aluminum-finned heating
- NetBotz universal sensor ports elements complete with safety thermostat (for manual
resetting) to cut off the power supply in the event of
- Alarm/Shutdown Contacts
overheating
- USB ports (Host, Device)
• High efficiency EU5 pleated air filters housed in a
- Ethernet dedicated plenum box
- HDMI display interface • Power phase correction capacitors for compressors
- Modbus • Active Flow Control to improve the balance of airflow
- Remote shutdown input between the cooling structure and IT equipment.
• Ability to interface with most common external • Energy meter and CO2 emission calculator
BMS on communication protocols and boosting on • Motorized damper on the air return side
connection towards Schneider monitoring systems:
- Modbus/RTU RS485 Accessories
- SNMP
The units can be supplied with the following external
- Modbus Over IP accessories:
- StruxureWare • Suction / discharge plenums
- StruxureON • Direct free-cooling plenums
- Cooling Tuner as service diagnostic tool • Floor stands with or without motorized damper
• Height adjustable base frame
Construction options
• Room temperature and humidity sensor
• Double power supply with automatic integrated • Smoke and fire sensors
management on the active line to provide
• Water leak detectors
redundancy and ensure a constant power supply
• 2-way pressostatic valve to modulate the water flow
through the braze plate condenser
• Condensing Pressure Regulation Valve (Flooding
Valve) to maintain a minimum condensing pressure
even with low water inlet temperature
Uniflair LE
TDER – TUER
Range
Cooling capacity: 20 ÷ 100 kW
Refrigerant R-410A
Available versions
• Downflow (TDER)
• Upflow (TUER)
Standard features
• Advanced microprocessor control system is available with local or remote user terminal. - Remote on/off switch
• The units are equipped with backward-curved fans with directly coupled - Ability to interface with modbus protocol directly on
asynchronous motor. RS485 serial card
• The structure of the unit is characterized by a self-supporting frame in galvanized steel - Ability to interface with main external communication
with panels. The external panels are coated with RAL9003 epoxy-polyester paint and protocols: BACnet, Lonworks, Trend, Metasys, TCP/IP,
internally lined with heat- and sound-proofing insulation. SNMP, and StruxureWare platform
• Electronic expansion valve is controlled by the microprocessor and a dedicated software
that increases the precision of the cooling and the energy efficiency of the cooling cycle. Construction options
• The cooling coil is designed for an elevated SHR and reduced pressure drops in the air
• Immersed electrode humidifier (D/U versions)
section. The coil is made from copper tubes mechanically expanded on aluminum fins,
• Low surface temperature electrical heaters
complete with a hydrophilic treatment.
with extended fans, complete with double safety
• The cooling coil is characterized by CW and direct expansion circuits interlaced to
thermostat and manual resetting (T/H versions)
increase the efficiency of the unit in all running conditions.
• Hot gas and hot water reheating
• Unit is equipped with an indirect free cooling system that provides the required
• Condensation control on refrigerant side with
cooling capacity when the external temperature is lower than the internal ambient.
constant water flow
Compressor power consumption is minimized while internal and external environments
are kept separate.
Accessories
• Internal water-cooled condenser braze is welded and made of AISI 304 stainless steel.
• Uniflair LE units meet the following directives: Machinery Directive 2006/42/EC (MD), The units can be supplied with the following
Electromagnetic compatibility Directive 2014/30/EU (EMC), Pressure equipment external accessories:
Directive 2014/68/EU (PED), Regulation (EU) No 517/2014 on fluorinated greenhouse
• Remote, semi-graphic user terminal
gases (F-GAS).
• RS485 serial adapter to communicate with
• High-efficiency, EU4-pleated air filters are housed in a metal frame and equipped with
external BMS
a dirty filter differential pressure switch and low airflow differential pressure switch.
• LON FTT10 serial adapter to communicate
• The Uniflair LE range offers the possibility to select units equipped with two compressors
with external BMS managed with LON protocol
(tandem) for each circuit, which grants better efficiency and regulation capacity at partial
loads (models with the **21 or **42 suffix). • TCP/IP serial adapter to communicate with external
BMS managed with SNMP protocol
• Total front access is available for unit maintenance.
• AFPS that can be adapted as a kit
• The electrical panel is situated in a compartment separated from the airflow
with installation instructions
and complies with the Machinery Directive 2006/42/EC (MD).
• Motorized damper
• Microprocessor control system includes:
• Condensate drain pump
- Integrated management of the EEV and refrigerating circuit parameters
• Suction from the top or front discharge plenums
- Local user terminal with external accessibility
• Adjustable floor stands
- Integrated LAN card for local network connection of a group of CRACs
- Rotation and active stand-by management
- Free contact for general and two for addressable alarms
Uniflair LE
TDEV – TUEV
Range
Cooling capacity: 20 ÷ 100 kW
Refrigerant R-410A
EC fans
Available versions
• Downflow (TDEV)
• Upflow (TUEV)
Standard features
• Advanced microprocessor control system is available with local or remote user terminal. - Rotation and active stand-by management
• The units are equipped with EC fans for efficiency maximization. - Free contact for general and two
• The structure of the unit is characterized by a self-supporting frame in galvanized steel for addressable alarms
with panels. The external panels are coated with RAL9003 epoxy-polyester paint and - Remote on/off switch
internally lined with heat- and sound-proofing insulation. - Ability to interface with modbus protocol directly on
• Electronic expansion valve is controlled by the microprocessor and a dedicated software RS485 serial card
that increases the precision of the cooling and the energy efficiency of the cooling cycle. - Ability to interface with main external communication
• Unit is equipped with an indirect free cooling system that provides the required cooling Protocols: BACnet, Lonworks, Trend, Metasys, TCP/IP,
capacity when the external temperature is lower than the internal ambient. SNMP, and StruxureWare platform
Compressor power consumption is minimized while internal and external
environments are kept separate. Construction options
• The cooling coil is designed for an elevated SHR and reduced pressure drops in the air
• Immersed electrode humidifier (D/U versions)
section. The coil is made from copper tubes mechanically expanded on aluminum fins,
• Low surface temperature electrical heaters with extended
complete with a hydrophilic treatment.
fans, complete with double safety thermostat and manual
• The cooling coil is characterized by CW and direct expansion circuits interlaced to
resetting (T/H versions)
increase the efficiency of the unit in all running conditions.
• Hot gas and hot water reheating
• Internal water-cooled condenser braze is welded and made of AISI 304 stainless steel.
• Uniflair LE units meet the following directives: Machinery Directive 2006/42/EC (MD),
Accessories
Electromagnetic compatibility Directive 2014/30/EU (EMC), Pressure equipment
Directive 2014/68/EU (PED), Regulation (EU) No 517/2014 on fluorinated greenhouse The units can be supplied with the following
gases (F-GAS). external accessories:
• High-efficiency, EU4-pleated air filters are housed in a metal frame and equipped with
• Remote, semi-graphic user terminal
a dirty filter differential pressure switch and low airflow differential pressure switch.
• RS485 serial adapter to communicate
• The Uniflair LE range offers the possibility to select units equipped with two
with external BMS
compressors (tandem) for each circuit, which grants better efficiency and regulation
capacity at partial loads (models with the **21 or **42 suffix). • LON FTT10 serial adapter to communicate
with external BMS managed with LON protocol
• Total front access is available for unit maintenance.
• TCP/IP serial adapter to communicate
• The electrical panel is situated in a compartment separated from the airflow and comp
with external BMS managed with SNMP protocol
lies with the Machinery Directive 2006/42/EC (MD).
• AFPS that can be adapted as a kit with
• Microprocessor control system includes:
installation instructions
- Integrated management of the cooling modes monitoring room temperature, external
• Motorized damper
temperature, and glycol circuit temperature
• Condensate drain pump
- Integrated management of the EEV and refrigerating circuit parameters
• Suction from the top or front discharge plenums
- Local user terminal with external accessibility
• Adjustable floor stands
- Integrated LAN card for local network connection of a group of CRACs
Uniflair LE
LDEV
Range
Cooling capacity: 70 ÷ 100 kW
Fixed speed compressors
Refrigerant R-410A
EC fans
Available versions
• Downflow (LDEV)
Standard features
• Downflow configuration with bottom or front discharge • New generation of hermetic scroll compressor with
and suction from the top. Intermediate Discharge Valves (IDVs), built-in thermal
• Metal structural frame and inside part made with hot- protection and anti-vibration feet
dip zinc-plated sheet steel • Refrigerant R410A
• External panels coated with RAL9003 epoxy-polyester • Electronic Expansion Valve (EEV) to provide accurate
paint and internally lined with heat- and sound- control of the refrigerant superheat ensuring high
proofing insulation to class 1 according to energy efficiency also at low external temperatures.
Class B1 according to DIN 4102, BS 476 part 7, • Energy saving units are equipped with a new patent
VO according to UL94, ASTM E84, class M1 pending solution. The 3-way valve is replaced by
according to NFP92-501 three flow control devices designed to maximize
• Internal panels for shutting-off the compartments efficiency and minimize water side pressure drops.
affected by the airflow, made with hot-dip zinc-plated • Electrical panel complying with Machinery Directive
sheet steel and captive screws 2006/42/EC (MD) and Electromagnetic compatibility
• High efficiency EU4 pleated air filters are contained Directive 2014/30/EU (EMC), Regulation (EU)
in a metal frame and equipped with a dirty filter No 517/2014 on fluorinated greenhouse gases
differential pressure switch and a low airflow (F-GAS), housed- in a compartment isolated from the
differential pressure switch. The filters are housed in a airflow and including 24V control circuit transformer,
dedicated plenum box. metal isolating screen for protection from live
• The units are equipped with the latest generation components, mains switch, thermomagnetic
Radical EC Fans for efficiency maximization. Impellers circuit-breakers, terminal board for no-voltage signal
are made of high-tech compound material with and control contacts.
optimized flow control, combined with highly efficient • 7-inch. IT Touch Screen display interface that allows
GreenTech EC motors. These fans are designed to to set operating parameters, monitor the trend
have easier serviceability with quick removability kit. of the main working parameters, and read any
• Low airflow differential pressure switch alarm messages.
• Cooling coil, mounted upstream of the fans, • Schneider Electric IT J-Controller (J5 18 DIN),
constructed of copper tubes expanded into complying with Machinery Directive 2006/42/EC
hydrophilic aluminum fins, complete with stainless (MD) and Electromagnetic compatibility Directive
steel tray and a flexible condensate drain hose 2014/30/EU (EMC), Regulation (EU) No 517/2014 on
fluorinated greenhouse gases (F-GAS), where are
• Brazed plate water-cooled condenser made from
connected analogical and digital inputs necessary for
stainless steel.
control of the unit.
• Double refrigerant circuit each equipped with a
fixed-speed scroll compressor.
• Refrigerant circuits complying with Pressure
Equipment Directive 2014/68/EU (PED) including:
liquid refrigerant receiver, filter-dryer and liquid sight
glass, electronic expansion valve, high-pressure
pressostats with manual reset.
DIMENSIONS
Height mm 2150 2150
Length mm 2082 2650
Depth mm 900 900
Uniflair LE
TDTR – TUTR
Range
Cooling capacity: 20 ÷ 100 kW
Refrigerant R-410A
Available versions
• Downflow (TDTR)
• Upflow (TUTR)
Standard features
• Advanced microprocessor control system is available • High-efficiency, EU4-pleated air filters are housed
with local or remote user terminal. in a metal frame and equipped with a dirty filter differential
• The units are equipped with backward-curved fans pressure switch and low airflow differential pressure switch.
and directly coupled asynchronous motor. • The Uniflair LE range offers the possibility to select units
• The structure of the unit is characterized equipped with two compressors (tandem) for each circuit,
by a self-supporting frame in galvanized steel which grants better efficiency and regulation capacity at
with panels. The external panels are coated partial loads (models with the **21 or **42 suffix).
with RAL9003 epoxy-polyester paint and internally • Total front access is included for unit maintenance.
lined with heat- and sound-proofing insulation. • The electrical panel is situated in a compartment separated
• Unit is characterized by two independent cooling from the airflow and complies with the Machinery Directive
sources — one CW with related circuit and one direct 2006/42/EC (MD).
expansion air cooled. • Microprocessor control system includes:
• Electronic expansion valve is controlled by the - Integrated management of the EEV
microprocessor and a dedicated software that and refrigerating circuit parameters
increases the cooling precision and the energy - Local user terminal with external accessibility
efficiency of the cooling cycle. - Integrated LAN card for local network connection of
• The cooling coil is designed for an elevated SHR a group of CRACs
and reduced pressure drops in the air section. The coil - Rotation and active stand-by management
is made from copper tubes mechanically expanded on - Free contact for general and two for addressable alarms
aluminum fins, complete with a hydrophilic treatment.
- Remote on/off switch
• Uniflair LE units meet the following directives:
- Ability to interface with modbus protocol
Machinery Directive 2006/42/EC (MD),
directly on RS485 serial card
Electromagnetic compatibility Directive 2014/30/EU
- Ability to interface with main external communication
(EMC), Pressure equipment Directive 2014/68/EU
protocols: BACnet, Lonworks, Trend, Metasys, TCP/IP,
(PED), Regulation (EU) No 517/2014 on fluorinated
SNMP, and StruxureWare platform
greenhouse gases (F-GAS).
Uniflair LE
TDTV – TUTV
Range
Cooling capacity: 20 ÷ 100 kW
Refrigerant R-410A
EC fans
Available versions
• Downflow (TDTV)
• Upflow (TUTV)
Standard features
• Advanced microprocessor control system is available • Uniflair LE units meet the following directives: Machinery Directive
with local or remote user terminal. 2006/42/EC (MD), Electromagnetic compatibility Directive 2014/30/EU
• The units are equipped with EC fans for (EMC), Pressure equipment Directive 2014/68/EU (PED), Regulation (EU)
efficiency maximization. No 517/2014 on fluorinated greenhouse gases (F-GAS).
• The structure of the unit is characterized • High-efficiency, EU4-pleated air filters are housed in a metal frame and
by a self-supporting frame in galvanized steel equipped with a dirty filter differential pressure switch and low airflow
with panels. The external panels are coated differential pressure switch.
with RAL9003 epoxy-polyester paint and internally • The Uniflair LE range offers the possibility to select units equipped with two
lined with heat- and sound-proofing insulation. compressors (tandem) for each circuit, which grants better efficiency and
• Electronic expansion valve is controlled regulation capacity at partial loads (models with the **21 or **42 suffix).
by the microprocessor and a dedicated software • Total front access is included for unit maintenance.
that increases the cooling precision and the energy • The electrical panel is situated in a compartment separated from the
efficiency of the cooling cycle. airflow and complies with the Machinery Directive 2006/42/EC (MD).
• Unit is characterized by two independent cooling • Microprocessor control system includes:
sources — one CW with related circuit and one - Integrated management of the EEV and refrigerating
direct expansion air cooled. circuit parameters
• The cooling coil is designed for an elevated SHR - Local user terminal with external accessibility
and reduced pressure drops in the air section. The coil - Integrated LAN card for local network connection of
is made from copper tubes mechanically expanded on a group of CRACs
aluminum fins, complete with a hydrophilic treatment. - Rotation and active stand-by management
• The cooling coil is characterized by CW and direct - Free contact for general and two for addressable alarms
expansion circuits interlaced to increase the efficiency
- Remote on/off switch
of the unit in all running conditions.
- Ability to interface with modbus protocol
• The CW circuit is equipped with a three-way valve
directly on RS485 serial card
and an actuator integrated with the microprocessor.
- Ability to interface with main external communication
protocols: BACnet, Lonworks, Trend, Metasys, TCP/IP,
SNMP, and StruxureWare platform
Uniflair LE
TDDR – TUDR
Range
Cooling capacity: 20 ÷ 100 kW
Refrigerant R-410A
Available versions
• Downflow (TDDR)
• Upflow (TUDR)
Standard features
• Advanced microprocessor control system is available • High-efficiency, EU4-pleated air filters are housed in a metal
with local or remote user terminal. frame and equipped with a dirty filter differential pressure
• The units are equipped with Backward-curved fans switch and low airflow differential
and directly coupled asynchronous motor. pressure switch.
• The structure of the unit is characterized by a self- • The Uniflair LE range offers the possibility to select units
supporting frame in galvanized steel with panels. equipped with two compressors (tandem) for each circuit,
The external panels are coated with RAL9003 which grants better efficiency and regulation capacity
epoxy-polyester paint and internally lined with heat- at partial loads (models with the **21 or **42 suffix).
and sound-proofing insulation. • Total front access is included for unit maintenance.
• Electronic expansion valve is controlled by the • The electrical panel is situated in a compartment separated
microprocessor and a dedicated software that from the airflow and complies with the Machinery Directive
increases the precision of the cooling and the energy 2006/42/EC (MD).
efficiency of the cooling cycle. • Microprocessor control system includes:
• The cooling coil is designed for an elevated SHR and - Integrated management of the EEV and refrigerating
reduced pressure drops in the air section. The coil is circuit parameters
made from copper tubes mechanically expanded on - Local user terminal with external accessibility
aluminum fins, complete with a hydrophilic treatment. - Integrated LAN card for local network connection of
• Internal water-cooled condenser braze is welded and a group of CRACs
made of AISI 304 stainless steel. - Rotation and active stand-by management
• Uniflair LE units meet the following directives: - Free contact for general and two for addressable alarms
Machinery Directive 2006/42/EC (MD), - Remote on/off switch
Electromagnetic compatibility Directive 2014/30/EU
- Ability to interface with modbus protocol
(EMC), Pressure equipment Directive 2014/68/EU
directly on RS485 serial card
(PED), Regulation (EU) No 517/2014 on fluorinated
- Ability to interface with main external communication
greenhouse gases (F-GAS).
protocols: BACnet, Lonworks, Trend, Metasys, TCP/IP,
SNMP, and StruxureWare platform
kW 23,8 30,4 46,2 55,9 60,5 90,5 87,8 96,0 and ESP = 20 Pa.
capacity1,2
Gross sensible cooling Data refers to nominal
kW 21,1 28,5 38,8 55,9 55,8 79,7 75,3 77,7 3
capacity1,2
conditions: Room
Gross total cooling at 24 °C-50% RH,
kW 20,5 28,3 38,6 53,9 53,9 97,6 97,3 97,6
capacity1,3
water temperature
Gross sensible cooling 7/12 °C; glycol 0%,
kW 20,4 28,2 38,4 53,7 53,7 96,7 96,4 96,7
capacity1,3
and ESP = 20 Pa.
DIMENSIONS
Height mm 1960 1960 1960 1960 1960 2150 2150 2150
4
Data refers to
downflow unit.
Length mm 1010 1310 1720 2170 2170 2580 2580 2580
Depth mm 750 865 865 865 750 865 865 865
TUDR MODELS 2242A 2542A 2842A
Fans nr. 3 3 3
Airflow m3/h 22160 23194 23194
N° of compressors 4 4 4
Refrigerating circuits 2 2 2
Gross total cooling
CW MODE DX MODE
Uniflair LE
TDDV – TUDV
Range
Cooling capacity: 20 ÷ 100 kW
Refrigerant R-410A
EC fans
Available versions
• Downflow (TDDV)
• Upflow (TUDV)
Standard features
• Advanced microprocessor control system is available with local or remote user terminal. • The electrical panel is situated in a compartment
• The units are equipped with EC fans for efficiency maximization. separated from the airflow and complies with the
• The structure of the unit is characterized by a self-supporting frame in galvanized steel Machinery Directive 2006/42/EC (MD).
with panels. The external panels are coated with RAL9003 epoxy-polyester paint and • Microprocessor control system includes:
internally lined with heat- and sound-proofing insulation. - Integrated management of the EEV and refrigerating
• Electronic expansion valve is controlled by the microprocessor and a dedicated circuit parameters
software that increases the precision of the cooling and the energy efficiency of - Local user terminal with external accessibility
the cooling cycle. - Integrated LAN card for local network connection of
• Unit is characterized by two independent cooling sources — one CW with related a group of CRACs
circuit and one direct expansion water cooled. - Rotation and active stand-by management
• The cooling coil is designed for an elevated SHR and reduced pressure drops in the - Free contact for general and two for addressable alarms
air section. The coil is made from copper tubes mechanically expanded on aluminum - Remote on/off switch
fins, complete with a hydrophilic treatment. - Ability to interface with modbus protocol directly on
• The cooling coil is characterized by CW and direct expansion circuits interlaced to RS485 serial card
increase the efficiency of the unit in all running conditions. - Ability to interface with main external communication
• Internal water-cooled condenser braze is welded and made of AISI 304 stainless steel. protocols: BACnet, Lonworks, Trend, Metasys, TCP/IP,
• The CW circuit is equipped with a three-way valve and an actuator integrated with SNMP, and StruxureWare platform
the microprocessor.
• Uniflair LE units meet the following directives: Machinery Directive 2006/42/EC (MD),
Electromagnetic compatibility Directive 2014/30/EU (EMC), Pressure equipment
Directive 2014/68/EU (PED), Regulation (EU) No 517/2014 on fluorinated greenhouse
gases (F-GAS).
• High-efficiency, EU4-pleated air filters are housed in a metal frame and equipped with
a dirty filter differential pressure switch and low airflow differential pressure switch.
• The Uniflair LE range offers the possibility to select units equipped with two compressors
(tandem) for each circuit, which grants better efficiency and regulation capacity at
partial loads (models with the **21 or **42 suffix).
• Total front access is included for unit maintenance.
kW 20,2 28,5 40,1 54,1 54,1 96,6 96,6 96,6 conditions: Room
capacity1,3
at 24 °C-50% RH,
Gross sensible cooling water temperature
kW 20,1 28,3 39,9 53,9 53,9 95,7 95,7 95,7
capacity1,3
7/12 °C; glycol 0%,
DIMENSIONS and ESP = 20 Pa.
Height mm 1960 1960 1960 1960 1960 2150 2150 2150
4
Data refers to
Length mm 1010 1310 1720 2170 2170 2580 2580 2580
downflow unit.
Depth mm 750 865 865 865 750 865 865 865
TUDV MODEL 2242A 2542A 2842A
Fans nr. 3 3 3
Airflow m3/h 22000 22500 22500
N° of compressors 4 4 4
Refrigerating circuits 2 2 2
Gross total cooling
CW MODE DX MODE
Uniflair LE
IDAV
Range
Cooling capacity: 20 ÷ 100 kW
Refrigerant R-410A
Brushless compressors
EC fans
Available versions
• Downflow air cooled
Standard features
• Brushless variable speed scroll DC compressor. • Internal water-cooled condenser braze is welded
• Units in tandem version (models **21) equipped and made of AISI 304 stainless steel.
with one brushless compressor and one fixed • Uniflair LE units meet the following directives:
speed compressor. Machinery Directive 2006/42/EC (MD), Electromagnetic
• Advanced microprocessor control system compatibility Directive 2014/30/EU (EMC), Pressure
with a local or remote user terminal. equipment Directive 2014/68/EU (PED), Regulation (EU)
• The units are equipped with EC fans for No 517/2014 on fluorinated greenhouse gases (F-GAS).
efficiency maximization. • High-efficiency, EU4-pleated air filters are housed in
• The structure of the unit is characterized by a metal frame and equipped with a dirty filter differential
a self-supporting frame in galvanized steel with pressure switch and low airflow differential pressure switch.
panels. The external panels are coated with • Total front access is available for unit maintenance.
RAL9003 epoxy-polyester paint and internally • The electrical panel is situated in a compartment separated
lined with heat- and sound-proofing insulation. from the airflow and complies with the Machinery Directive
• Electronic expansion valve is controlled by the 2006/42/EC (MD).
microprocessor and a dedicated software that • Advanced microprocessor control UG50.
increases the cooling precision and the energy • Free-contact for general alarm and 2 for addressable alarms.
efficiency of the cooling cycle. • Remote on/off switch.
• The cooling coil is designed for an elevated SHR • Integrated RS485 serial card for direct connection
and reduced pressure drops in the air section. external BMS (modbus).
• The coil is made from copper tubes mechanically • Second slot for additional serial card for BMS
expanded on aluminum fins, complete with a connection (optional).
hydrophilic treatment. • Clock card integrated in the unit.
• Discharge temperature control (option).
Uniflair LE
IDAV - IUAV
Range
Cooling capacity: 50 ÷ 140 kW
1 VSD compressor and 1 fixed speed compressor
Refrigerant R-410A
EC fans
Available versions
• Downflow (IDAV)
• Upflow (IUAV)
Standard features
• Air flow configuration: • Refrigerant circuits complying with Pressure
- Downflow configuration with bottom or front Equipment Directive 2014/68/EU (PED) including:
discharge and suction from the top liquid refrigerant receiver, filter-dryer and liquid sight
glass, electronic expansion valve, high-pressure
- Upflow configuration with top discharge and
pressostats with manual reset.
bottom or front return
• New generation of hermetic scroll compressor:
• Metal structural frame and inside part made with
hot-dip zinc-plated sheet steel - Fixed-speed compressors with Intermediate
Discharge Valves (IDVs), built-in thermal protection
• External panels coated with RAL9003 epoxy-polyester
and anti-vibration feet
paint and internally lined with heat- and sound-
proofing insulation to class 1 according to Class - Variable speed scroll compressors with a
B1 according to DIN 4102, BS 476 part 7,VO brushless Interior Permanent Magnet (IPM)
according to UL94, ASTM E84, class M1 and dedicated variable speed drive designed
according to NFP92-501 to provide maximum efficiency across the full
operating range
• Internal panels for shutting-off the compartments
affected by the airflow, made with hot-dip zinc-plated • Refrigerant R410A
sheet steel and captive screws • Electronic Expansion Valve (EEV) to provide accurate
• High efficiency EU4 pleated air filters are contained control of the refrigerant superheat ensuring high
in a metal frame and equipped with a dirty filter energy efficiency also at low external temperatures.
differential pressure switch and a low airflow • Electrical panel complying with Machinery Directive
differential pressure switch. Downflow units have 2006/42/EC (MD) and Electromagnetic compatibility
filters housed in a dedicated plenum box. Directive 2014/30/EU (EMC), Regulation (EU)
• The units are equipped with the latest generation No 517/2014 on fluorinated greenhouse gases (F-GAS),
Radical EC Fans for efficiency maximization. Impellers housed- in a compartment isolated from the airflow and
are made of high-tech compound material with including 24V control circuit transformer, metal isolating
optimized flow control, combined with highly efficient screen for protection from live components, mains
GreenTech EC motors. These fans are designed to switch, thermomagnetic circuit-breakers, terminal board
have easier serviceability with quick removability kit. for no-voltage signal and control contacts.
• Low airflow differential pressure switch • 7 inch. IT Touch Screen display interface that allows
to set operating parameters, monitor the trend of
• Cooling coil, mounted upstream of the fans,
the main working parameters, and read any alarm
constructed of copper tubes expanded into
messages.
hydrophilic aluminum fins, complete with stainless
steel tray and a flexible condensate drain hose • Schneider Electric IT J-Controller (J5 18 DIN),
complying with Machinery Directive 2006/42/EC
• Single (**11A models) or double (**22A models)
(MD) and Electromagnetic compatibility Directive
refrigerant circuit each equipped with a scroll
2014/30/EU (EMC), Regulation (EU) No 517/2014 on
compressor (one fixed-speed and one brushless
fluorinated greenhouse gases (F-GAS), where are
inverter driven, except the 1511A model that is
connected analogical and digital inputs necessary for
equipped with only one brushless inverter driven
control of the unit.
scroll compressor)
Uniflair LE
IXAV
Range
Cooling capacity: 70 ÷ 150 kW
1 VSD compressor and 1 fixed speed compressor
FPO Refrigerant R-410A
EC fans
Available versions
• Underfloor (IXAV)
Standard features
• Underfloor configuration with top return and multiple • Refrigerant circuits complying with Pressure
fan module configurations: Equipment Directive 2014/68/EU (PED) including:
- bottom discharge liquid refrigerant receiver, filter-dryer and liquid sight
glass, electronic expansion valve, high-pressure
- rear discharge
pressostats with manual reset.
- front discharge
• New generation of hermetic scroll compressor:
- front and side discharge
- Fixed-speed compressors with Intermediate
- fully open discharge Discharge Valves (IDVs), built-in thermal protection
• Metal structural frame and inside part made with and anti-vibration feet
hot-dip zinc-plated sheet steel - Variable speed scroll compressors with a
• External panels coated with RAL9003 epoxy-polyester brushless Interior Permanent Magnet (IPM)
paint and internally lined with heat- and sound-proofing and dedicated variable speed drive designed
insulation to class 1 according to Class B1 according to provide maximum efficiency across the full
to DIN 4102, BS 476 part 7,VO according to UL94, operating range
ASTM E84, class M1 according to NFP92-501 • Refrigerant R410A
• Internal panels for shutting-off the compartments • Electronic Expansion Valve (EEV) to provide accurate
affected by the airflow, made with hot-dip zinc-plated control of the refrigerant superheat ensuring high
sheet steel and captive screws energy efficiency also at low external temperatures.
• High efficiency EU4 pleated air filters are contained • Electrical panel complying with Machinery Directive
in a metal frame and equipped with a dirty filter 2006/42/EC (MD) and Electromagnetic compatibility
differential pressure switch and a low airflow differential Directive 2014/30/EU (EMC), Regulation (EU)
pressure switch. Air filters are housed in a dedicated No 517/2014 on fluorinated greenhouse gases (F-GAS),
plenum box. housed- in a compartment isolated from the airflow and
• The units are equipped with the latest generation including 24V control circuit transformer, metal isolating
Radical EC Fans for efficiency maximization. Impellers screen for protection from live components, mains
are made of high-tech compound material with switch, thermomagnetic circuit-breakers, terminal board
optimized flow control, combined with highly efficient for no-voltage signal and control contacts.
GreenTech EC motors. These fans are designed to • 7 inch. IT Touch Screen display interface that allows
have easier serviceability with quick removability kit. to set operating parameters, monitor the trend of
• Low airflow differential pressure switch the main working parameters, and read any alarm
messages.
• Cooling coil, mounted upstream of the fans,
constructed of copper tubes expanded into hydrophilic • Schneider Electric IT J-Controller (J5 18 DIN),
aluminum fins, complete with stainless steel tray and a complying with Machinery Directive 2006/42/EC (MD)
flexible condensate drain hose and Electromagnetic compatibility Directive 2014/30/
EU (EMC), Regulation (EU) No 517/2014 on fluorinated
• Double (**22A models) refrigerant circuit each
greenhouse gases (F-GAS), where are connected
equipped with a scroll compressor (one fixed-speed
analogical and digital inputs necessary for control of
and one brushless inverter driven)
the unit.
Uniflair LE
IDWV - IUWV
Range
Cooling capacity: 50 ÷ 140 kW
1 VSD compressor and 1 fixed speed compressor
Refrigerant R-410A
EC fans
Available versions
• Downflow (IDWV)
• Upflow (IUWV)
Standard features
• Air flow configuration: • Refrigerant circuits complying with Pressure
- Downflow configuration with bottom or front Equipment Directive 2014/68/EU (PED) including:
discharge and suction from the top liquid refrigerant receiver, filter-dryer and liquid sight
glass, electronic expansion valve, high-pressure
- Upflow configuration with top discharge and bottom
pressostats with manual reset.
or front return
• New generation of hermetic scroll compressor:
• Metal structural frame and inside part made with hot-
dip zinc-plated sheet steel - Fixed-speed compressors with Intermediate
Discharge Valves (IDVs), built-in thermal protection
• External panels coated with RAL9003 epoxy-polyester
and anti-vibration feet
paint and internally lined with heat- and sound-proofing
insulation to class 1 according to Class B1 according - Variable speed scroll compressors with a
to DIN 4102, BS 476 part 7,VO according to UL94, brushless Interior Permanent Magnet (IPM)
ASTM E84, class M1 according to NFP92-501 and dedicated variable speed drive designed
to provide maximum efficiency across the full
• Internal panels for shutting-off the compartments
operating range
affected by the airflow, made with hot-dip zinc-plated
sheet steel and captive screws • Refrigerant R410A
• High efficiency EU4 pleated air filters are contained • Electronic Expansion Valve (EEV) to provide accurate
in a metal frame and equipped with a dirty filter control of the refrigerant superheat ensuring high
differential pressure switch and a low airflow energy efficiency also at low external temperatures.
differential pressure switch. Downflow units have • Electrical panel complying with Machinery Directive
filters housed in a dedicated plenum box. 2006/42/EC (MD) and Electromagnetic compatibility
• The units are equipped with the latest generation Directive 2014/30/EU (EMC), Regulation (EU)
Radical EC Fans for efficiency maximization. Impellers No 517/2014 on fluorinated greenhouse gases
are made of high-tech compound material with (F-GAS), housed- in a compartment isolated from the
optimized flow control, combined with highly efficient airflow and including 24V control circuit transformer,
GreenTech EC motors. These fans are designed to metal isolating screen for protection from live
have easier serviceability with quick removability kit. components, mains switch, thermomagnetic
circuit-breakers, terminal board for no-voltage signal
• Low airflow differential pressure switch
and control contacts.
• Cooling coil, mounted upstream of the fans,
• 7-inch. IT Touch Screen display interface that
constructed of copper tubes expanded into
allows to set operating parameters, monitor the
hydrophilic aluminum fins, complete with stainless
trend of the main working parameters, and read
steel tray and a flexible condensate drain hose
any alarm messages.
• Brazed plate water-cooled condenser made from
• Schneider Electric IT J-Controller (J5 18 DIN),
stainless steel.
complying with Machinery Directive 2006/42/EC
• Single (**11A models) or double (**22A models) (MD) and Electromagnetic compatibility Directive
refrigerant circuit each equipped with a scroll 2014/30/EU (EMC), Regulation (EU) No 517/2014 on
compressor (one fixed-speed and one brushless fluorinated greenhouse gases (F-GAS), where are
inverter driven, except the 1511A model that is connected analogical and digital inputs necessary for
equipped with only one brushless inverter driven control of the unit.
scroll compressor)
Uniflair LE
IXWV
Range
Cooling capacity: 70 ÷ 150 kW
1 VSD compressor and 1 fixed speed compressor
Refrigerant R-410A
EC fans
Available versions
• Underfloor (IXWV)
Standard features
• Underfloor configuration with top return and multiple • Brazed plate water-cooled condenser made from
fan module configurations: stainless steel.
- bottom discharge • Double (**22A models) refrigerant circuit each
- rear discharge equipped with a scroll compressor (one fixed-speed
and one brushless inverter driven)
- front discharge
• Refrigerant circuits complying with Pressure
- front and side discharge Equipment Directive 2014/68/EU (PED) including:
- fully open discharge liquid refrigerant receiver, filter-dryer and liquid sight
• Metal structural frame and inside part made with hot- glass, electronic expansion valve, high-pressure
dip zinc-plated sheet steel pressostats with manual reset.
• External panels coated with RAL9003 epoxy-polyester • New generation of hermetic scroll compressor:
paint and internally lined with heat- and sound- - Fixed-speed compressors with Intermediate
proofing insulation to class 1 according to Class B1 Discharge Valves (IDVs), built-in thermal protection
according to DIN 4102, BS 476 part 7,VO according and anti-vibration feet
to UL94, ASTM E84, class M1 according to NFP92- - Variable speed scroll compressors with a
501 brushless Interior Permanent Magnet (IPM)
• Internal panels for shutting-off the compartments and dedicated variable speed drive designed
affected by the airflow, made with hot-dip zinc-plated to provide maximum efficiency across the full
sheet steel and captive screws operating range
• High efficiency EU4 pleated air filters are contained • Refrigerant R410A
in a metal frame and equipped with a dirty filter • Electronic Expansion Valve (EEV) to provide accurate
differential pressure switch and a low airflow control of the refrigerant superheat ensuring high
differential pressure switch. Air filters are housed in a energy efficiency also at low external temperatures.
dedicated plenum box.
• Electrical panel complying with Machinery Directive
• The units are equipped with the latest generation 2006/42/EC (MD) and Electromagnetic compatibility
Radical EC Fans for efficiency maximization. Impellers Directive 2014/30/EU (EMC), Regulation (EU)
are made of high-tech compound material with No 517/2014 on fluorinated greenhouse gases (F-GAS),
optimized flow control, combined with highly efficient housed- in a compartment isolated from the airflow and
GreenTech EC motors. These fans are designed to including 24V control circuit transformer, metal isolating
have easier serviceability with quick removability kit. screen for protection from live components, mains
• Low airflow differential pressure switch switch, thermomagnetic circuit-breakers, terminal board
• Cooling coil, mounted upstream of the fans, for no-voltage signal and control contacts.
constructed of copper tubes expanded into • 7 inch. IT Touch Screen display interface that allows
hydrophilic aluminum fins, complete with stainless to set operating parameters, monitor the trend
steel tray and a flexible condensate drain hose of the main working parameters, and read any
alarm messages.
Uniflair LE
IDEV - IUEV
Range
Cooling capacity: 50 ÷ 100 kW
1 VSD compressor and 1 fixed speed compressor
Refrigerant R-410A
EC fans
Available versions
• Downflow (IDEV)
• Upflow (IUEV)
Standard features
• Air flow configuration: • Refrigerant circuits complying with Pressure Equipment
- Downflow configuration with bottom or front Directive 2014/68/EU (PED) including: liquid refrigerant
discharge and suction from the top receiver, filter-dryer and liquid sight glass, electronic
expansion valve, high-pressure pressostats with manual
- Upflow configuration with top discharge and bottom
reset.
or front return
• New generation of hermetic scroll compressor:
• Metal structural frame and inside part made with hot-
dip zinc-plated sheet steel - Fixed-speed compressors with Intermediate
Discharge Valves (IDVs), built-in thermal protection
• External panels coated with RAL9003 epoxy-polyester
and anti-vibration feet
paint and internally lined with heat- and sound-proofing
insulation to class 1 according to Class B1 according - Variable speed scroll compressors with a brushless
to DIN 4102, BS 476 part 7,VO according to UL94, Interior Permanent Magnet (IPM) and dedicated
ASTM E84, class M1 according to NFP92-501 variable speed drive designed to provide maximum
efficiency across the full operating range
• Internal panels for shutting-off the compartments
affected by the airflow, made with hot-dip zinc-plated • Refrigerant R410A
sheet steel and captive screws • Electronic Expansion Valve (EEV) to provide accurate
• High efficiency EU4 pleated air filters are contained control of the refrigerant superheat ensuring high
in a metal frame and equipped with a dirty filter energy efficiency also at low external temperatures.
differential pressure switch and a low airflow • Energy saving units are equipped with a new patent
differential pressure switch. Downflow units have pending solution. The 3-way valve is replaced by three
filters housed in a dedicated plenum box. flow control devices designed to maximize efficiency
• The units are equipped with the latest generation and minimize water side pressure drops.
Radical EC Fans for efficiency maximization. Impellers • Electrical panel complying with Machinery Directive
are made of high-tech compound material with 2006/42/EC (MD) and Electromagnetic compatibility
optimized flow control, combined with highly efficient Directive 2014/30/EU (EMC), Regulation (EU)
GreenTech EC motors. These fans are designed to No 517/2014 on fluorinated greenhouse gases (F-GAS),
have easier serviceability with quick removability kit. housed- in a compartment isolated from the airflow and
• Low airflow differential pressure switch including 24V control circuit transformer, metal isolating
screen for protection from live components, mains
• Cooling coil, mounted upstream of the fans,
switch, thermomagnetic circuit-breakers, terminal board
constructed of copper tubes expanded into
for no-voltage signal and control contacts.
hydrophilic aluminum fins, complete with stainless
steel tray and a flexible condensate drain hose • 7-inch. IT Touch Screen display interface that allows to
set operating parameters, monitor the trend of the main
• Brazed plate water-cooled condenser made from
working parameters, and read any alarm messages.
stainless steel.
• Schneider Electric IT J-Controller (J5 18 DIN),
• Single (**11A models) or double (**22A models)
complying with Machinery Directive 2006/42/EC
refrigerant circuit each equipped with a scroll
(MD) and Electromagnetic compatibility Directive
compressor (one fixed-speed and one brushless
2014/30/EU (EMC), Regulation (EU) No 517/2014 on
inverter driven, except the 1511A model that is
fluorinated greenhouse gases (F-GAS), where are
equipped with only one brushless inverter driven
connected analogical and digital inputs necessary for
scroll compressor)
control of the unit.
Uniflair LE
IXEV
Range
Cooling capacity: 60 ÷ 150 kW
1 VSD compressor and 1 fixed speed compressor
Refrigerant R-410A
EC fans
Available versions
• Underfloor (IXEV)
Standard features
• Underfloor configuration with top return and multiple • Single (**11A models) or double (**22A models)
fan module configurations: refrigerant circuit each equipped with a scroll
- bottom discharge compressor (one fixed-speed and one brushless
inverter driven, except the 2311A model that is
- rear discharge
equipped with only one brushless inverter driven
- front discharge scroll compressor)
- front and side discharge • Refrigerant circuits complying with Pressure
- fully open discharge Equipment Directive 2014/68/EU (PED) including:
liquid refrigerant receiver, filter-dryer and liquid sight
• Metal structural frame and inside part made with
glass, electronic expansion valve, high-pressure
hot-dip zinc-plated sheet steel
pressostats with manual reset.
• External panels coated with RAL9003 epoxy-polyester
• New generation of hermetic scroll compressor:
paint and internally lined with heat- and sound-proofing
insulation to class 1 according to Class B1 according - Fixed-speed compressors with Intermediate
to DIN 4102, BS 476 part 7,VO according to UL94, Discharge Valves (IDVs), built-in thermal protection
ASTM E84, class M1 according to NFP92-501 and anti-vibration feet
• Internal panels for shutting-off the compartments - Variable speed scroll compressors with a brushless
affected by the airflow, made with hot-dip zinc-plated Interior Permanent Magnet (IPM) and dedicated
sheet steel and captive screws variable speed drive designed to provide maximum
efficiency across the full operating range
• High efficiency EU4 pleated air filters are contained
in a metal frame and equipped with a dirty filter • Refrigerant R410A
differential pressure switch and a low airflow differential • Electronic Expansion Valve (EEV) to provide accurate
pressure switch. Air filters are housed in a dedicated control of the refrigerant superheat ensuring high
plenum box. energy efficiency also at low external temperatures.
• The units are equipped with the latest generation • Energy saving units are equipped with a new patent
Radical EC Fans for efficiency maximization. Impellers pending solution. The 3-way valve is replaced by three
are made of high-tech compound material with flow control devices designed to maximize efficiency
optimized flow control, combined with highly efficient and minimize water side pressure drops.
GreenTech EC motors. These fans are designed to
• Electrical panel complying with Machinery Directive
have easier serviceability with quick removability kit.
2006/42/EC (MD) and Electromagnetic compatibility
• Low airflow differential pressure switch Directive 2014/30/EU (EMC), Regulation (EU)
• Cooling coil, mounted upstream of the fans, No 517/2014 on fluorinated greenhouse gases
constructed of copper tubes expanded into (F-GAS), housed- in a compartment isolated from the
hydrophilic aluminum fins, complete with stainless airflow and including 24V control circuit transformer,
steel tray and a flexible condensate drain hose metal isolating screen for protection from live
components, mains switch, thermomagnetic
• Brazed plate water-cooled condenser made from
circuit-breakers, terminal board for no-voltage signal
stainless steel.
and control contacts.
- Alarm/Shutdown Contacts • Fan module shipped separately from the upper unit
Uniflair CAP
Range
Cooling capacity: 7 ÷ 160 kW
Refrigerant R-410A
Uniflair OCC
Range
Heat dissipation: 40 ÷ 200 kW
Refrigerant R-410A
AC or EC fans
TECHNICAL DATA
1
Gross cooling
capacities; fans must
OCC - ONE CIRCUIT 1701 2101 2401 2601 3101 3301 3901
be deduced to obtain
Fan Type AC / EC axial fans
net cooling data.
Power supply V/ph/Hz 230/1/50 230/1/50 230/1/50 230/1/50 230/1/50 400/3/50 400/3/50
Fans Nr. 2 2 2 2 3 2 3 2
Measured in free field
Airflow Nr. 2 2 2 3 3 2 2 conditions at 10 meters
Heat dissipation1 m3/h 17227 16313 15216 22275 23372 32700 29525 from the unit.
Noise level2 kW 45,8 55,5 62,1 69,7 81,9 87,9 102
Refrigerating circuits dB(A) 45 45 45 47 47 51 51
DIMENSIONS
Height mm 1150 1150 1150 1150 1150 1250 1250
Length mm 2380 2380 2380 2660 2660 2660 2660
Depth mm 800 800 800 800 800 800 800
IUAV MODEL 3502 4202 4702 5302 6202 6702 7702
Fan type AC / EC axial fans
Power supply V/ph/Hz 230/1/50 230/1/50 230/1/50 230/1/50 230/1/50 400/3/50 400/3/50
Fans Nr. 4 4 4 6 6 4 4
Airflow m3/h 34453 32625 30431 44550 46744 65400 59050
Heat dissipation1 kW 91,6 111,0 124,2 139,4 163,8 175,8 204,0
Noise level2 dB(A) 48 48 48 50 50 54 54
DIMENSIONS
Height mm 2253 2253 2253 2253 2253 2453 2453
Length mm 2380 2380 2380 2660 2660 2660 2660
Depth mm 800 800 800 800 800 800 800
Active floor
Range
Cooling capacity: 6 ÷ 15 kW
Standard features
• Active floor is a flexible and modular system for cooling
data centers with medium- and high-density loads.
Integrated within a modular access floor in front of the
intake section of the rack, the Active Floor fits exactly
into a modular access floor panel measuring 600 mm
x 600 mm. The cold air produced by the close control
perimeter units is directly channeled to the source of the
thermal load thanks to the advanced adjustment of the
direction of the airflow. The active floor creates a high-
density bubble of air, which is maintained at a constant
temperature along the whole intake section of the rack,
guaranteeing operation at the nominal design conditions.
The airflow varies according to the actual thermal load
and is detected by two sensors placed on the discharge
section of the servers.
• Active floor employs variable speed EC, motor-driven
fans to minimize energy consumption.
• This solution may be used in stand-alone applications as
well as with perimeter close control units equipped with
underfloor pressure control.
• The active floor guarantees optimum operation
of high-density equipment for loads installed in each
module of 25 kW and 40 kW with solutions featuring
the two modules certified by TUV.
TECHNICAL DATA
ACTIVE FLOOR
Power supply V/ph/Hz 220/1+N/60
N° of fans/motor 1/E.C
Max airflow m³/h/CFM 4988/2936
Nominal airflow m³/h/CFM 2880/1650
Min airflow m³/h/CFM 1698/999
DIMENSIONS
Height mm/inch 230/9.1
Width mm/inch 600/23.6
Depth mm/inch 600/23.6
Around-the-clock operation every day of the year • Control through the Uniflair Netvisor
supervision system
• Highly reliable equipment
• Connection to a centralized supervision system
• Reduced running costs
• Operational accuracy
• Continuous service
• Flexibility
• Low running costs
Uniflair WM
WDA – WDF
Range
Cooling capacity: 6 ÷ 15 kW
Refrigerant R407C
Available versions
• Without direct free-cooling (WDA)
• With direct free-cooling (WDF)
Standard features
• Monoblock conditioning units can be installed on the outside wall of the air • The double external paneling is available in galvanized,
conditioned room. painted sheet steel and gives separate access to the fan
• Built-in air condenser is included. The units can be supplied completely assembled compartment and electric board compartments. This
and filled with refrigerant; all the components are set in the factory for normal enables maintenance and regulation to be carried out
working conditions and the electrical and cooling functions are tested. Installation without having to turn the unit off.
only requires simple electrical wiring and mechanical fixing to the shelter, even by • Power supply:
nonspecialized personnel. - 400 V/3+N/50 Hz standard on request
• The direct free-cooling units (WMF) are supplied with a motorized damper. During - 230 V/1/50 Hz on 221 and 341 models
free-cooling the excess air is expelled from the room through the condenser section - Main power supply + UPS 48 VDC (evaporator DC fan/s)
without using any extra overpressure dampers. • Microprocessor control.
• Complete access to all the components allows servicing entirely from the outside, • Scroll compressor.
without having to enter the room which is normally protected by controlled access. • EU4 filter (optional).
• The external screws are stainless steel, antitamper and can only be removed using • Modulating condenser fan/s speed control.
special tools.
• Free-cooling metal pre-filter.
TECHNICAL DATA
1
Data refers to
mechanical operation:
WDA – WDF MODEL WDF0221A WDF0341A WDF0481A WDF0501A
Ambient temperature:
Power supply V/ph/Hz 400/3+N/50
27 °C/40% RH,
Mechanical cooling1 external temperature
Sensible cooling capacity kW 6,0/6,0 9,0/9,0 12,0/12,0 15,0/15,0 35 °C/R407C
Airflow m³/h 1650 2350 2900 4200 (data consider
inlet and outlet
COMPONENT FEATURES
evaporating coil),
N° of evaporator fans 1 2 2 2 and Maximum external
N° of condenser fans 1 1 1 1 temperature 45 °C.
Compressor power
kW 1,25 1,94 3,56 3,78
consumption1
DIMENSIONS
Height mm 1800 1800 1800 1800
Width mm 950 950 950 1120
Depth mm 650 650 650 650
Uniflair WM
WMA – WMF
Range
Cooling capacity: 3.9 ÷ 16.9 kW
Refrigerant R407C
Available versions
- Without direct free-cooling (WMA)
- With direct free-cooling (WMF)
Standard features
• Monoblock conditioning units are installed on the outside wall of the air conditioned room. • Power supply:
• Air condenser is built in. The units can be supplied completely assembled - 230 V/1/50 Hz or 400 V/3+N/50 Hz
and filled with refrigerant. (standard, according to the model)
• All the components are set in the factory for normal working conditions. Electrical - Main power supply + UPS 230 V
and cooling functions are all tested. Installation only requires simple electrical wiring - Main power supply + UPS
and mechanical fixing to the shelter, even by nonspecialized personnel. - 48 VDC (evaporator DC-fan/s)
• The direct free-cooling units (WMF) are supplied with a motorized damper. • Microprocessor control.
During free-cooling the excess of air is expelled from the room through • Scroll compressor (rotary for 0121 model) housed
the condenser section without using extra overpressure dampers. in compartment isolated from the airflow.
• Complete access to all the components so that servicing can be entirely done from the • EU4 filter (optional).
outside, without having to enter the room which is normally protected by controlled access. • Modulating condenser fan/s speed control.
• The external screws are stainless steel, antitamper and can only be removed using • Free-cooling metal pre-filter.
special tools.
• The double external paneling is available in galvanized, painted sheet steel and gives
separate access to the fan compartment and electric board compartments. This enables
maintenance and regulation to be carried out without having to turn the unit off.
TECHNICAL DATA
1
Room: 26 °C/40% RH;
external temperature:
WMA – WMF MODELS 0121 0181 0251 0281 0331 0551 0661
35 °C; R407C.
Power supply V/ph/Hz 230/1/50 400/3+N/50
Mechanical cooling1 2
Room: 26 °C; external
Sensible cooling capacity kW 3,9/3,9 5,4/5,4 7,4/7,4 8,2/8,2 9,6/9,6 15,2/15,2 16,9/16,9 temperature:
Airflow m³ / h 1240 1460 2240 2240 2670 4580 4580 14 °C; R407C.
WMF MODEL
3
ARI standard.
Free-cooling2
Sensible cooling capacity kW 5,0 5,8 8,5 8,5 9,2 17,4 17,4 4
Optional.
Airflow m³/h 1230 1430 2100 2100 2280 4310 4310
5
Measurements taken
COMPONENT FEATURES
at 1 meter above the
N° of evaporator fans 1 1 2 2 2 1 1 floor and at a distance
N° of condenser fans 1 1 1 1 2 1 1 of 5 meters from
Air filter efficiency EU2 EU2 EU2 EU2 EU2 EU2 EU2 the unit in free field,
Nominal compressor power3 kW 1,2 1,8 2,2 2,5 3,0 4,4 5,2 mechanical cooling.
Uniflair MB
XMA – XMF – XDA – XDF
Range
Cooling capacity: XM* 5.7 ÷ 12.3 kW XD* 6.3-15.0 kW
Refrigerant R407C
Available versions
• Upflow (XMA)
• Upflow with free-cooling (XMF)
• Downflow (XDA)
• Downflow with free-cooling (XDF)
Standard features
• Monoblock conditioning units are installed inside • Cooling circuit includes:
the installation. These units are ideal when the required - Filter and flow sight glass
solution is easy to install with all the refrigerant - Thermostatic expansion valve
components already installed. - High- and low-pressure pressostats
• The unit has a self-supporting steel structure - Scroll compressor with thermal protection
finished in epoxy powder and external panels in steel - Ecological refrigerant R407C
finished in epoxy powder; it’s lined internally - Modulating condenser fan speed regulation.
with abrasion-resistant, self-extinguishing material • The microprocessor control manages the unit
for noise and heat insulation. autonomously and the free-cooling function
• Units are supplied ready for installation, completely and can be integrated with the most common BMSs.
assembled and filled with refrigerant in the factory, The control includes:
where they are calibrated and the electric and cooling - Microprocessor control board and user terminal
systems are tested.
- Room temperature sensor
• Easy installation and connection to the outside
- Mixed air temperature sensor (X*F version only)
is provided using rigid or flexible pipes that are fitted
- External temperature sensor (X*F version only)
to the window.
• Power supply:
• The air filtration is provided with an EU2-efficiency air
- 230 V/ 1/ 50 Hz or 400 V/3+N/50 Hz
filter in self-extinguishing material and a rigid metal
(Standard, according to the model)
frame; the free-cooling version is available with
an additional free-cooling metal pre-filter. EU4 filters - Main power supply + UPS 230 V
are available as an option. - Main power supply + UPS 48 VDC
• The evaporating and condensing fans are made (evaporator DC fan/s, available only for XMF)
of in galvanized steel. Double-inlet centrifugal fan(s) • Microprocessor control.
with forward-curved blower are keyed directly • Scroll compressor with low noise level.
to motor shaft. • EU4 filter (optional).
• The electrical panel is housed in a compartment • Modulating condenser fan/s speed control.
isolated from the airflow, complying with Machinery • Free-cooling metal pre-filter.
Directive 2006/42/EC (MD), Regulation (EU)
No 517/2014 on fluorinated greenhouse gases
(F-GAS). Separate power supply for fans and
microprocessor is available as an option.
Uniflair SP
UCA – UCF – UWA – UWF
Range
Cooling capacity: 5,9 ÷ 14,5 kW
Refrigerant R407C
Available versions
• Ceiling mounted (UCA)
• Ceiling mounted with direct free-cooling (UCF)
• Wall mounted (UWA)
• Wall mounted with direct free-cooling (UWF)
Standard features
• Units are made of two separate sections: the evaporation section, which is installed inside the • Internal and external units
conditioned room (UCA – UCF – UWA – UWF), and the condensation section (MRA), which is are powered separately.
installed on the outside. • Power supply:
• The evaporator is designed to be fixed to the ceiling or a wall and, with advanced microprocessor - 230 V/1/0 Hz or 400 V/3+N/50 Hz
control, it is very precise in maintaining the set parameters inside the conditioned room. (Standard, according to the model)
• Servicing is very simple as different access is given to the electrical board, the technical • Main power supply + UPS
compartment, and the servomotor for the free-cooling damper. - 48 VDC (evaporator DC-fan/s)
• There is a special panel for the fan compartment, which means calibration and servicing can be • Evaporator sections are equipped with:
carried out safely without having to turn the unit off. - Microprocessor control
• UCF units have free-cooling that intakes air from the back of the unit through a connection - EU4 filter (optional)
that can be made using either rigged ducting or flexible piping. - Scroll compressor
• The user terminal (on request) is fitted to the wall for the ceiling units and onboard - Modulating condenser fan/s speed control
for the wall fitted units, and gives complete control for the unit regarding changing
and displaying the operating parameters.
TECHNICAL DATA 1
Room: 26 °C/45% RH;
MODELS CEILING UCA – UCF WALL UWA – UWF external temperature:
0341 0401 0481 0341 0401 0481 35 °C; R407C.
Power supply V/ph/Hz 230/1/50 230/1/50 2
Room: 26 °C; external
Mechanical cooling1
temperature: 14 °C;
Sensible cooling cap. kW 5,9/5,9 7,1/7,1 8,1/8,1 10,4/10,4 14,5/14,5 5,9/5,9 7,1/7,1 8,1/8,1 10,4/10,4 14,5/14,5 R407C.
Airflow m³/h 1850 1850 220 2600 3900 1850 1850 2200 2600 3900
UCF-UWF 0341 0401 0481 0341 0401 0481
3
ARI standard.
Free-cooling2
Sensible cooling cap. kW 6,7 6,7 6,9 9,5 14 6,7 6,7 6,9 9,5 14
Airflow m³/h 1850 1850 220 2600 3900 1850 1850 2200 2600 3900
DIMENSIONS
Height mm 330 330 330 410 410 1200 1200 1200 1300 1300
Width mm 950 950 950 1150 1150 980 980 980 1150 1150
Depth mm 1050 1050 1050 1300 1300 330 330 330 410 410
EXTERNAL UNIT MRA 0221 0281 0341 0401 0611 0211 0281 0341 0401 0611
Power supply V/ph/Hz 230/1/50 400/3+N/50 230/1/50 400/3+N/50
Nominal compressor
kW 1,7 2,1 2,6 3,1 4,6 1,7 2,1 2,6 3,1 4,6
power3
Airflow m³/h 1800 2990 2990 6290 6290 1800 2990 2990 6290 6290
DIMENSIONS
Height mm 610 610 610 1230 1230 610 610 610 1230 1230
Width mm 850 850 850 1200 1200 850 850 850 1200 1200
Depth mm 345 345 345 80 80 345 345 345 480 480
schneider‑electric.com.
March 2019
©2019 Schneider Electric. All Rights Reserved. Schneider Electric | Life Is On is a trademark
and the property of Schneider Electric SE, its subsidiaries, and affiliated companies.
998-20086951_GMA-US_A