PROFESSIONAL TESTING, INSPECTION
METROLOGY 8 ENGINEERING SERVICES Excellence, it’s Our Promise
CERTIFICAT D'ETALONNAGE
CALIBRATION CERTIFICATE,
N° E£02-05-1/20
Délivréa: CERT
Issued to: ZI La Charguia- Rue 8600 N°82-Tunis, Tunisie
Equipement étalonné
Calibrated instrument
Désignati WELDING MACHINE
Designation
Constructeur: = LINCOLIN type: Invertee
Manufacturer : type: 270 SX.
NP de séri 1191001306 Identification: Inexistant
Serial Number : identification
Date d’émission : 11/02/2020
Date of issue :
Ce certificat comprend (03) pages
‘This certificate include (03) pages
PRESIDENT DIRECTEUR GENERAL.
(CHIEF EXECUTIVE OFFICER
SMADHI MOHAMED
a reproduction de ce cerifcat nest autorise que sous I forte de fesimilé photographie intra
This ertficte may not be reproduced other ta in Fl by photographic rocess
PROTIMESS sa, Lot 34 Zone Industrielle
iba 4, 1152 ~ Zaghouan — Tunisie
421672 668 421, Fax: +216 72 668 431
site: www.protimess.com, Email : protimess@iprotimess.comRésolution
Resolution:
Alichage:
Display:
Remarques
ates
NA
200A
1A
Numérique
CALIBRATION CERTIFICATE N° EO2.05-1/20
‘Siti candion
Température
Temperature
Humidité
Humidity
Liew
1812°C
5085 %RH
Site client
Ds
Reéalisé par
@’étalonnage
Date of calibration
11/02/2020
BWajih
Place of calibration
Mode opératoire
Operating procedure
L’étalonnage a été effectué par comparaison directe des indications de l'instrument soumis 4 I’étalonnage avec un
étalon réfierencé ci-dessous, les deux placées dans le méme milieu de comparaison. L’étalonnage a été effectué en
twois points répartis sur toute I’étendue de mesure,
The calibration was performed by direct comparison of instrument indications under test with a standard referenced below,
both placed in the same comparison environment. Calibration was performed at three temperature points.
Référentiels utilisées
Used references
DCT-PREV-E 10 Procedure of electrical calibration
LAB GTA 10
Etalons utilisées
Reference equipments used
‘Technical guide for accreditation
Désignation | Marque ‘Modéle NE Certificat
Designation Brand. model Certificate N”
Ampermetric clamp FLUKE 316 27420200WS
Page 2/3
PROTIMESS sa, Lot 34 Zone Industrielle Zriba 4, 1152 - Zaghouan — Tunisie
MF :127320Si/A/MLO00 , R.C : BO6214252012, Tél: +216 72 668 421, Fax: +216 72 668431
site: www.protimess.com, Email: protimesvaiprotimess.comCALIBRATION CERTIFICATE N° EO2.05-1/20
‘Traceability
L’étalonnage a été réalisé avec des étalons raccordés A la chaine (inter nationale,
‘The calibration has been executed by instruments that are traceable to (inter)national standards.
Incertitude
‘Uncertainty
Les incertitudes élargies mentionnées sont celles correspondant & deux incertitudes-types. Les incertitudes sont calculées en
tenant compte des différentes composantes d’incertitudes, étalons de référence, moyen d’étalonnage, conditions
environnement, contribution de I'instrument étalonné, répétabilité
‘The reported expanded uncertainties is determined by a coverage factor K~2 providing @ level of confidence of approximately
95%. The uncertainties are calculated taking into account the different components of uncertainties, reference standards,
calibration means, environmental conditions, contribution of the calibrated instrument, repeat
Résultats de ’étalonnage
Calibration Results
Valeur indique par Valeur mesuré Correction | Incertitude élargie
instrument par létalon Expanded
uncertainty (K=2)
@ A) (a) (a)
70 708 08
102 103,5 os 45
160 1624 24
Fin de Certificat
-S End of Certificate ce
METI
DOCUMENT O
Page 3/3
PROTIMESS sa, Lot 34~Zone Industrielle Zriba 4, 1152 - Zaghouan—T
7320S/A/MIOO0 , R.C : BO6214252012, Tél: +216 72 668 421, Fax: +216 72 668 431
site: www-protimess.com, Email : protimess@jprotimess.com