Professional Documents
Culture Documents
Geotechnical Engineering II Lab Quiz 1: Required
Geotechnical Engineering II Lab Quiz 1: Required
* Required
MCQs
While determining relative density, the surcharge weight applied to the top 1 point
2 psi
1.5 psi
1 psi
0.5 psi
Air Pressure
Water Pressure
200 kPa
50 kPa
150 kPa
100 kPa
In a CU test, the drainage valve will be kept ________ while applying the deviator
stress. *
Open
Closed
With a specific gravity of 2.6, emax of 0.767, emin of 0.433, what is the dry 2 points
1.814
1.471
1.625
1.8
incorrect *
Unconsolidated Undrained
Unconsolidated Drained
Consolidated Undrained
Consolidated Drained
The corrected area used in the direct shear test is always _______ than the 1 point
less
more
same
In direct shear test, normal load applied on top of the soil results in * 1 point
normal stress
shear stress
When soil is in its loosest state, relative density is 0% and its relative 1 point
compaction is *
0%
40%
80%
100%
What is the undrained shear strength of soil which has the following Mohr's 1 point
stress circle? *
150 kPa
250 kPa
125 kPa
100 kPa
The strength parameters obtained from the direct shear test are 1 point
True
False
At a frequency of 60Hz, the corresponding amplitude and running time of 1 point
the vibrating table used to determine relative density must be ____ mm and
____ minutes respectively. *
Drained test
The same mold used to perform relative density test on sands can be used 1 point
for gravels. *
True
False
50 - 100%
80 - 100%
95 - 100%
0 - 100%
UCT is generally performed on ___________ * 1 point
σ1
σ3
σ1-σ3
(σ1-σ3)/2
When preparing a cylinder of soil, the length to diameter ratio of the 1 point
2/3
between 2 and 3.
1.5
In a direct shear test, the shear stress and normal stress on a dry sand 1 point
sample at failure are 0.6 kg/cm2 and 1 kg/cm2 respectively. The angle of
internal friction of the sand will be nearly *
25
31
37
43
When the Mohr circle is drawn from the results of UCT, its diameter will be 1 point
equal to *
cohesion
shear Strength
undrained Strength
While performing a Direct Shear Test in a 6cm*6cm shear box, failure was 2 points
observed after the deflection dial gauge reached 170, and the load dial
gauge reached 72. The least count of the deflection dial gauge is
0.01mm/div and the proving ring constant is 0.82lb/div. The shear stress at
failure is _______. *
16.8 kPa
75.11 kPa
2 kPa
72.98 kPa
In a triaxial test, the values of σ1 and σ3 are 200 kPa and 100 kPa 1 point
respectively. What will the radius of the Mohr's stress circle be? *
50 kPa
100 kPa
150 kPa
200 kPa
Which of the following triaxial tests is the slow test? * 1 point
Unconsolidated Undrained
Consolidation Undrained
Consolidated Drained
Unconfined Compression
The corrected area used in the unconfined compression test is always 1 point
less
more
same
What is the angle of internal friction for the following soil? * 1 point
37.96ᵒ
0.9115ᵒ
42.34ᵒ
3.2172ᵒ
In plastic failure, load corresponding to __________ strain is taken as the 1 point
failure load *
10 %
5%
15%
30 %
50 %
A proving ring is used to determine the applied load due to its consistent 1 point
____________ properties. *
Compressive
Tensile
Elastic
Plastic
The measured in-situ bulk density of soil at a construction site is 1.620 2 points
95%
99.7%
96.5%
90%
Back Submit
This content is neither created nor endorsed by Google. Report Abuse - Terms of Service - Privacy Policy
Forms