Professional Documents
Culture Documents
CONTENTS
Chapter 11.37
TROUBLESHOOTING.................................................................... 11.37-3
CONTENTS
Chapter 11.37
GENERAL DESCRIPTION
Plastic Case
Metal Case
DISPLAY ILLUMINATION
Two integral cold-cathode fluorescent lamps provide back
illumination of the LCD panel.
TEMPERATURE CONTROL
Air is drawn through an external filter into the display interior, by
two fans that are controlled by a circuit incorporating a thermistor
placed at the exhaust vent at the top of the casing. The speed of the
fans is increased to provide cooling when the display is heated by
the sun. The fans still provide a gentle airflow even when the
display is exposed to extreme cold. In this case the warm air inside
the ATM is used to keep the LCD panel slightly warm.
TEST TOOLS
None.
STRAPPING
None.
ADJUSTMENTS
There are no field serviceable parts inside the display. Failed units
should be returned for repair.
WARNING
Warm-up
Allow the display to warm-up in the host system for ten minutes so
that the temperature of the display and system board stabilises
before adjustments are attempted.
Press the MENU button to display the main menu.
Use the + and - buttons to scroll through the main menu func-
NCR — CONFIDENTIAL AND PROPRIETARY
Use pursuant to Company Instructions
11.37-2 DECEMBER 2006
UNIVERSAL 12.1 INCH STANDARD BRIGHTNESS COLOUR DISPLAY
tions list.
Press the MENU button to select a function from the list.
Press the + or - buttons to make the required adjustment.
Press the MENU button to save the setting.
Repeat the procedure for the remaining functions.
Press the MENU button to exit the menu saving the settings.
TROUBLESHOOTING
To ensure an unimpeded airflow through the display casing, clean
or renew the foam air filter at a preventive maintenance call to the
ATM. The filter can be removed by flexing the outer part of the
plastic holder until it unclips from the inner part. Vacuum or tap
out the dust from the filter or fit a new filter.
CONNECTOR ASSIGNMENT
The position of the connectors on the rear of the display module are
shown in the illustration below:
LTM121
Menu
Data
Signal
Connector
Power
CD1224TBS/12
Data
Signal
Connector
Menu
Not Used
Power
POWER CONNECTOR
The 4-way power connector on the LCD display has the following
pinout (looking into the connector):
+5 V RTN 3 1 +5 V
+12 V RTN 4 2 +12 V
GND 6
RED 1 GND 11
GND 7
GREEN 2 DATA 12
GND 8
BLUE 3 H.SYNC 13
N/C 9
N/C 4 V.SYNC 14
GND 10
GND 5 CLOCK 15
CABLE INFORMATION
This section shows the cabling to the LCD display in the
personaS86 ATM.
VGA SIGNAL
RED VIDEO 1
V V V V V V V V V V V V V V V
1
V V V V V V V V V V V V V V V
GREEN VIDEO
2 2
BLUE VIDEO
3 3
N/C N/C
4 4
GND
5 5
RED RTN
6 6
GREEN RTN
7 7
BLUE RTN
8 8
+5 V (FUSED) N/C
9 9
SYNC GND
10 10
N/C GND
11 11
DDC SERIAL DATA
12 12
HORIZ SYNC
13 13
VERT SYNC
14 14
DDC SERIAL CLOCK
15 15
J7 FACIA UNI_CONNECT J1
12 V RTN 12 V RTN
B5 B5
V V
V V V V
V V
V V
7 4
Liquid Crystal
12 V 12 V
Display
32 B6 B6 2
5 V RTN
3
5V
1
5 V RTN
Power Supply Unit
5V
Depository
Shutter
10
V V
4
5 V RTN
5V
J6
Dispenser
5V
Shutter
1 A1 A1 10
V V
V V
V V
V V
5 V RTN
19 A2 A2 4