Professional Documents
Culture Documents
LED TV
SERVICE MANUAL
CHASSIS : LM91X
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS 2
SA ET PRECAUTIONS
SERVICIN PRECAUTIONS 4
SPECI ICATION
AD USTMENT INSTRUCTION
TROU LE SHOOTIN 12
EXPLODED VIE 24
Copyright LG Electronics. Inc. All right reserved. -2- LGE Internal Use Only
Only for training and service purposes
SA ET PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and E ploded Vie .
It is essential that these special safety parts should be replaced ith the same components as recommended in this manual to prevent
Shoc , Fire, or other Hazards.
Do not modify the original design ithout permission of manufacturer.
General Guidance Lea age Current Hot Chec (See belo Figure)
Plug the AC cord directly into the AC outlet.
An isolation Transformer should al ays be used during the
servicing of a receiver hose chassis is not isolated from the AC Do not use a line Isolation Transformer during this chec .
po er line. Use a transformer of ade uate po er rating as this Connect 1. K/10 att resistor in parallel ith a 0.1 uF capacitor
protects the technician from accidents resulting in personal in ury bet een a no n good earth ground ( ater Pipe, Conduit, etc.)
from electrical shoc s. and the e posed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
It ill also protect the receiver and it s components from being ith 1000 ohms/volt or more sensitivity.
damaged by accidental shorts of the circuitry that may be Reverse plug the AC cord into the AC outlet and repeat AC voltage
inadvertently introduced during the service operation. measurements for each e posed metallic part. Any voltage
measured must not e ceed 0.7 volt RMS hich is corresponds to
If any fuse (or Fusible Resistor) in this TV receiver is blo n, 0. mA.
replace it ith the specified. In case any measurement is out of the limits specified, there is
possibility of shoc hazard and the set must be chec ed and
hen replacing a high attage resistor (O ide Metal Film Resistor, repaired before it is returned to the customer.
over 1W), eep the resistor 10mm a ay from PCB.
Lea age Current Hot Chec circuit
Keep ires a ay from high voltage or high temperature parts.
AC Volt-meter
al ays perform an AC lea age current chec on the e posed Good Earth Ground
such as WATER PIPE,
metallic parts of the cabinet, such as antennas, terminals, etc., to CONDUIT etc.
To Instrument's
be sure the set is safe to operate ithout damage of electrical 0.15µF
exposed
shoc . METALLIC PARTS
Lea age Current Cold Chec (Antenna Cold Chec ) 1.5 Kohm/10W
ith the instrument AC plug removed from AC source, connect an
electrical umper across the t o AC plug prongs. Place the AC
When 25A is impressed between Earth and 2nd Ground
s itch in the on position, connect one lead of ohm-meter to the AC for 1 second, Resistance must be less than 0.1
plug prongs tied together and touch other ohm-meter lead in turn to *Base on Adjustment standard
each e posed metallic parts such as antenna terminals, phone
ac s, etc.
If the e posed metallic part has a return path to the chassis, the
measured resistance should be bet een 1MΩ and .2MΩ.
hen the e posed metal has no return path to the chassis the
reading must be infinite.
An other abnormality e ists that must be corrected before the
receiver is returned to the customer.
Copyright LG Electronics. Inc. All right reserved. - - LGE Internal Use Only
Only for training and service purposes
SERVICIN PRECAUTIONS
CAUTION: Before servicing receivers covered by this service unit under test.
manual and its supplements and addenda, read and follo the 2. After removing an electrical assembly e uipped ith ES
SAFETY PRECAUTIONS on page of this publication. devices, place the assembly on a conductive surface such as
NOTE: If unforeseen circumstances create conflict bet een the aluminum foil, to prevent electrostatic charge buildup or
follo ing servicing precautions and any of the safety precautions on e posure of the assembly.
page of this publication, al ays follo the safety precautions. . Use only a grounded-tip soldering iron to solder or unsolder ES
Remember: Safety First. devices.
4. Use only an anti-static type solder removal device. Some solder
General Servicing Precautions removal devices not classified as anti-static can generate
1. Al ays unplug the receiver AC po er cord from the AC po er electrical charges sufficient to damage ES devices.
source before . Do not use freon-propelled chemicals. These can generate
a. Removing or reinstalling any component, circuit board electrical charges sufficient to damage ES devices.
module or any other receiver assembly. 6. Do not remove a replacement ES device from its protective
b. Disconnecting or reconnecting any receiver electrical plug or pac age until immediately before you are ready to install it.
other electrical connection. (Most replacement ES devices are pac aged ith leads
c. Connecting a test substitute in parallel ith an electrolytic electrically shorted together by conductive foam, aluminum foil
capacitor in the receiver. or comparable conductive material).
CAUTION: A rong part substitution or incorrect polarity 7. Immediately before removing the protective material from the
installation of electrolytic capacitors may result in an leads of a replacement ES device, touch the protective material
e plosion hazard. to the chassis or circuit assembly into hich the device ill be
installed.
2. Test high voltage only by measuring it ith an appropriate high CAUTION: Be sure no po er is applied to the chassis or circuit,
voltage meter or other voltage measuring device (DVM, and observe all other safety precautions.
FETVOM, etc) e uipped ith a suitable high voltage probe. 8. Minimize bodily motions hen handling unpac aged
Do not test high voltage by dra ing an arc . replacement ES devices. (Other ise harmless motion such as
. Do not spray chemicals on or near this receiver or any of its the brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity
4. Unless specified other ise in this service manual, clean sufficient to damage an ES device.)
electrical contacts only by applying the follo ing mi ture to the
contacts ith a pipe cleaner, cotton-tipped stic or comparable General Soldering Guidelines
non-abrasive applicator 10 (by volume) Acetone and 0 (by 1. Use a grounded-tip, lo - attage soldering iron and appropriate
volume) isopropyl alcohol ( 0 - strength) tip size and shape that ill maintain tip temperature ithin the
CAUTION: This is a flammable mi ture. range or 00 F to 600 F.
Unless specified other ise in this service manual, lubrication of 2. Use an appropriate gauge of RMA resin-core solder composed
contacts in not re uired. of 60 parts tin/40 parts lead.
. Do not defeat any plug/soc et B voltage interloc s ith hich . Keep the soldering iron tip clean and ell tinned.
receivers covered by this service manual might be e uipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall ire-
6. Do not apply AC po er to this instrument and/or any of its bristle (0. inch, or 1.2 cm) brush ith a metal handle.
electrical assemblies unless all solid-state device heat sin s are Do not use freon-propelled spray-on cleaners.
correctly installed. . Use the follo ing unsoldering techni ue
7. Al ays connect the test receiver ground lead to the receiver a. Allo the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive ( 00 F to 600 F)
lead. b. Heat the component lead until the solder melts.
Al ays remove the test receiver ground lead last. c. uic ly dra the melted solder ith an anti-static, suction-
8. Use ith this receiver only the test fi tures specified in this type solder removal device or ith solder braid.
service manual. CAUTION: or uic ly to avoid overheating the circuit
CAUTION: Do not connect the test fi ture ground strap to any board printed foil.
heat sin in this receiver. 6. Use the follo ing soldering techni ue.
a. Allo the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices ( 00 F to 600 F)
Some semiconductor (solid-state) devices can be damaged easily b. First, hold the soldering iron tip and solder the strand against
by static electricity. Such components commonly are called the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. E amples of typical ES c. uic ly move the soldering iron tip to the unction of the
devices are integrated circuits and some field-effect transistors and component lead and the printed circuit foil, and hold it there
semiconductor chip components. The follo ing techni ues only until the solder flo s onto and around both the
should be used to help reduce the incidence of component component lead and the foil.
damage caused by static by static electricity. CAUTION: or uic ly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-e uipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any e cess or
charge on your body by touching a no n earth ground. splashed solder ith a small ire-bristle brush.
Alternatively, obtain and ear a commercially available
discharging rist strap device, hich should be removed to
prevent potential shoc reasons prior to applying po er to the
Copyright LG Electronics. Inc. All right reserved. -4- LGE Internal Use Only
Only for training and service purposes
IC Remove/Replacement CAUTION: Maintain original spacing between the replaced
Some chassis circuit boards have slotted holes (oblong) through component and adjacent components and the circuit board to
which the IC leads are inserted and then bent flat against the prevent excessive component temperatures.
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with Circuit Board Foil Repair
boards using the familiar round hole, use the standard technique Excessive heat applied to the copper foil of any printed circuit
as outlined in paragraphs 5 and 6 above. board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
Removal following guidelines and procedures should be followed whenever
1. Desolder and straighten each IC lead in one operation by gently this condition is encountered.
prying up on the lead with the soldering iron tip as the solder
melts. At IC Connections
2. Draw away the melted solder with an anti-static suction-type To repair a defective copper pattern at IC connections use the
solder removal device (or with solder braid) before removing the following procedure to install a jumper wire on the copper pattern
IC. side of the circuit board. (Use this technique only on IC
Replacement connections).
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and 1. Carefully remove the damaged copper pattern with a sharp
solder it. knife. (Remove only as much copper as absolutely necessary).
3. Clean the soldered areas with a small wire-bristle brush. 2. carefully scratch away the solder resist and acrylic coating (if
(It is not necessary to reapply acrylic coating to the areas). used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
"Small-Signal" Discrete Transistor carefully crimp it around the IC pin. Solder the IC connection.
Removal/Replacement 4. Route the jumper wire along the path of the out-away copper
1. Remove the defective transistor by clipping its leads as close as pattern and let it overlap the previously scraped end of the good
possible to the component body. copper pattern. Solder the overlapped area and clip off any
2. Bend into a "U" shape the end of each of three leads remaining excess jumper wire.
on the circuit board.
3. Bend into a "U" shape the replacement transistor leads. At Other Connections
4. Connect the replacement transistor leads to the corresponding Use the following technique to repair the defective copper pattern
leads extending from the circuit board and crimp the "U" with at connections other than IC Pins. This technique involves the
long nose pliers to insure metal to metal contact then solder installation of a jumper wire on the component side of the circuit
each connection. board.
Power Output, Transistor Device 1. Remove the defective copper pattern with a sharp knife.
Removal/Replacement Remove at least 1/4 inch of copper, to ensure that a hazardous
1. Heat and remove all solder from around the transistor leads. condition will not exist if the jumper wire opens.
2. Remove the heat sink mounting screw (if so equipped). 2. Trace along the copper pattern from both sides of the pattern
3. Carefully remove the transistor from the heat sink of the circuit break and locate the nearest component that is directly
board. connected to the affected copper pattern.
4. Insert new transistor in the circuit board. 3. Connect insulated 20-gauge jumper wire from the lead of the
5. Solder each transistor lead, and clip off excess lead. nearest component on one side of the pattern break to the lead
6. Replace heat sink. of the nearest component on the other side.
Carefully crimp and solder the connections.
Diode Removal/Replacement CAUTION: Be sure the insulated jumper wire is dressed so the
1. Remove defective diode by clipping its leads as close as it does not touch components or sharp edges.
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Copyright LG Electronics. Inc. All right reserved. - - LGE Internal Use Only
Only for training and service purposes
SPECI ICATION
NOTE : Speci cations and others are sub ect to change ithout notice for improvement.
1 A R
This spec sheet is applied all of the TV used LM 1 chassis.
2 S
Each part is tested as belo ithout special appointment
T
1) Performance : LGE TV test method follo ed
2) Demanded other speci cation
- Safety : CE,IEC speci cation
- EMC : CE,IEC speci cation
4
41 R -PC
No. Item Speci cation Remar s
1 Supported Sync. Type Separate Sync.(RGB), SOG
Horizontal 0 6 Hz
2 Operating Fre uency Analog
Vertical 6 61 Hz
Ma 1 66 768 60 Hz
Operating Fre uency Analog
Recommend 1 66 768 60 Hz
Temp : 10 C C
4 Operating Environment
Humidity : 20 80
Temp : -10 C 60 C non condensing
Storage Environment
Humidity : 0 non condensing
4 2 TV
No. Item Speci cation Remar s
1 Mar et Central and South America
2 Broadcasting system NTSC, PAL-M, PAL-N
BAND Available Channel
VHF 02 1
Available Channel
UHF 14 6
CATV 02 12
4 Receiving system Upper Heterodyne
Video Input PAL, SECAM, NTSC Rear (1EA)
6 RGB Input RGB-PC(Analog (D-SUB 1 Pin) Rear (1EA)
7 USB Input MP , PEG, Movie Rear (1EA)
8 AV Audio Output RF/AV/HDMI Audio Output Rear (1EA)
HDMI Input HDMI-DTV Rear (1EA)
10 Audio Input (1EA) AV RGB-PC L/R Input(1EA)
Copyright LG Electronics. Inc. All right reserved. -6- LGE Internal Use Only
Only for training and service purposes
5 R I PC
No. Resolution H-fre ( Hz) V-fre .(Hz) Pi el cloc (MHz) Proposed Remar
1 640 480 1.46 . 4 2 .17
2 800 600 7.87 60. 17 40.0
1024 768 48. 6 60.0 6 .0
4 1280 720 47.77 .8 74.
11 2 864 4. 4 60.0 80
6 1 66 768 47.71 .7 8 .
HDMI I DTV
No Resolution H-fre ( Hz) V-fre .( Hz) Pi el cloc (MHz) Proposed Remar s
1 720 480 1 .7 . 4 1 . 00 SDTV, DVD 480I( 2 I)
2 720 480 1 .7 60.00 1 . 14 SDTV, DVD 480I( 2 I) Spec. out but display.
720 76 1 .62 0.00 1 . 00 SDTV, DVD 76I(62 I) 0Hz
4 720 480 1.47 . 4 27 SDTV 480P
720 480 1. 60.00 27.027 SDTV 480P
6 720 76 1.2 0.00 27 SDTV 76P
7 1280 720 44. 6 . 4 74.176 HDTV 720P
8 1280 720 4 60.00 74.2 HDTV 720P
1280 720 7. 0.00 74.2 HDTV 720P
10 1 20 1080 28.12 0.00 74.2 HDTV 1080I
11 1 20 1080 .72 . 4 74.176 HDTV 1080I
12 1 20 1080 .7 60.00 74.2 HDTV 1080I
1 1 20 1080 6.2 0.00 148. HDTV 1080P
14 1 20 1080 67.4 2 . 4 148. 0 HDTV 1080P
1 1 20 1080 67. 60.00 148. HDTV 1080P
16 1 20 1080 27 24.00 74.2 HDTV 1080P
17 1 20 1080 .7 0.00 74.2 HDTV 1080P
18 1 20 1080 26. 7 2 . 7 74.2 HDTV 1080P
1 1 20 1080 .716 2 . 76 74.2 HDTV 1080P
Copyright LG Electronics. Inc. All right reserved. -7- LGE Internal Use Only
Only for training and service purposes
AD USTMENT INSTRUCTION
1 A R 2 D
This spec. sheet applies to LM 1 Chassis applied TV all - The EDID data is automatically saved.
models manufactured in TV factory
2 4 EDID DATA
- 2 MT4 A(RGB-PC)
2 S RGB-PC : 128Bytes
1) Because this is not a hot chassis, it is not necessary to 0 1 2 4 6 7 8 A B C D E F
10 01 17 01 0 80 4 1D 78 EA 4D A 6 4F E 26
Caution 20 0F 47 4A 21 08 00 81 80 81 C0 71 40 B 00 81 40
70 00 2 44 20 48 44 20 4C 47 20 4 6 0A 20 01 0
80 02 0 21 F1 4F 84 0 0 02 20 22 10 11 1 12 14
M PC A A 0 1F 07 16 01 26 11 07 0 0 7F 07 6 0 0C 00 10
1 ADC C A0 00 02 A 80 18 71 8 2D 40 8 2C 4 00 0 2 21
D0 00 0 2 21 00 00 1E 01 1D 80 D0 72 1C 16 20 10
NO Item CMD CMD Data 0
1 2 E0 2C 2 80 0 2 21 00 00 E 02 A 80 D0 72 8 2D
F0 40 10 2C 4 20 0 2 21 00 00 1E 00 00 00 00 6F
Enter Ad ust A A 0 0 hen transfer the
Ad ust MODE Mode In Mode In ,
Carry the command.
Ad ust Se uence
aa 00 00 Enter Ad ust Mode
b 00 60 RGB Input (1024 768)
ad 00 10 Ad ust 1024 768 RGB
aa 00 0 End Ad ust mode
2 EDID D
21 O
- It is a VESA regulation. A PC or a MNT ill display an
optimal resolution through information sharing ithout any
necessity of user input. It is a realization of Plug and Play .
22 E
- Since EDID data is embedded, EDID do nload IG, HDMI
cable and D-sub cable are not need.
Copyright LG Electronics. Inc. All right reserved. -8- LGE Internal Use Only
Only for training and service purposes
4 A A 414 A C P
(1) RS-2 2C Command used during auto-ad .
41 A RS-2 2C COMMAND
411 O E plantion
CMD ID DATA
/B ad . Ob ective Ho -it- or s b 00 00 Begin hite Balance ad ustment
(1) Ob ective: To reduce each Panel s /B deviation End hite Balance ad ustment
(2) Ho -it- or s : hen R/G/B gain in the OSD is at 1 2, it b 00 ff
(internal pattern disappears )
means the panel is at its Full Dynamic Range. In order to
prevent saturation of Full Dynamic range and data, one of (2) Ad ustment Map
R/G/B is ed at 1 2, and the other t o is lo ered to nd Command Data Range Default
Ad . item
the desired value. (lo er caseASCII) (He .) (Decimal)
( ) Ad ustment condition : normal temperature CMD1 CMD2 MIN MA
1) Surrounding Temperature : 2 C C R Gain g 00 C0
2) arm-up time: About Min G Gain h 00 C0
) Surrounding Humidity : 20 80 B Gain i 00 C0
4) Before hite balance ad ustment, Keep po er on Cool
R Cut
status, don t po er off G Cut
Ad . condition and cautionary items B Cut
(1) Lighting condition in surrounding area surrounding lighting R Gain a 00 C0
should be lo er 10 lu . Try to isolate ad . area into dar
G Gain b 00 C0
surrounding.
B Gain c 00 C0
(2) Probe location: Color Analyzer (CA-210) probe should Medium
R Cut
be ithin 10cm and perpendicular of the module surface
G Cut
(80 100 )
( ) Aging time B Cut
1) After Aging Start, Keep the Po er ON status during R Gain d 00 C0
Minutes. G Gain e 00 C0
2) In case of LCD, Bac -light on should be chec ed arm B Gain f 00 C0
using no signal or Full- hite pattern. R Cut
G Cut
412 E
(1) Color Analyzer: CA-210 (NCG: CH / CG: CH12 / LED:
CH14)
(2) Ad . Computer (During auto ad ., RS-2 2C protocol is
needed)
( ) Ad ust Remocon
(4) Video Signal Generator MSPG- 2 F 720p/204-
Gray(Model: 217, Pattern: 4 )
Color Analyzer Matri should be calibrated using CS-1000
41 E
Co lo r Analyzer
Probe RS -232C
DFT JIG
Co m p ut er
RGB Cable RS -232C RS -232C
Copyright LG Electronics. Inc. All right reserved. - - LGE Internal Use Only
Only for training and service purposes
415 A 5 T O
Auto B calibration Method : Press AD ey on the Ad ustment remote control,
1) Set TV in AD mode using P-ONLY ey (or PO ER ON then select Tool option.
ey)
2) Place optical probe on the center of the display
- It need to chec probe condition of zero calibration
before ad ustment. S - I -
) Connect RS-2 2C Cable After nal inspection, press IN-STOP ey of the Ad ustment
4) Select mode in AD Program and begin a ad ustment. remote control and chec that the unit goes to Stand-by
) hen B ad ustment is completed ith OK message, mode.
chec ad ustment status of pre-set mode (Cool, Medium,
arm)
6) Remove probe and RS-2 2C cable.
/B Ad . must begin as start command b 00 00 , and n-
ND H-
ish as end command b 00 ff , and Ad . offset if need. 1 ND HI-POT -
1) Chec the PO ER CABLE and SIGNAL CABE insertion
LED hite balance table condition
If Model is Polaris Model, G-gain is applied.
(1) Cool Mode 2 ND HI-POT -
1) Purpose : Especially G-gain ad ust leads to the lu- 1) Pallet moves in the station. (PO ER CORD / AV CORD is
minance enhancement. Ad ust the color temperature tightly inserted)
to reduce the deviation of the module color tempera- 2) Connect the AV ACK Tester.
ture. ) Controller (G S10 -4) on.
2) Principle : To ad ust the hite balance ithout the 4) GND Test (Auto)
saturation, Ad ust the G gain more than 172 ( If R - If Test is failed, Buzzer operates.
gain or G gain is more than 2 , G gain can ad ust - If Test is passed, e ecute ne t process (Hi-pot test).
less than 172 ) and change the others ( R/B Gain ). (Remove A/V CORD from A/V ACK BO )
) Ad ustment mode : mode Cool ) HI-POT test (Auto)
(2) Medium / arm Mode - If Test is failed, Buzzer operates.
1) Purpose : Ad ust the color temperature to reduce the - If Test is passed, GOOD Lamp on and move to ne t
deviation of the module color temperature. process automatically.
2) Principle : To ad ust the hite balance ithout the
saturation, Fi the one of R/G/B gain to 1 2 (default
data) and decrease the others. C
)Ad ustment mode : T o modes Medium / arm 1) Test voltage
- GND: 1. KV/min at 100mA
41 R - SIGNAL: KV/min at 100mA
( hite Balance Ad . coordinate and color temperature) 2) TEST time: 1 second
1) Luminance: 204 Gray, 80IRE ) TEST POINT
2) Standard color coordinate and temperature using CS-1000 - GND Test PO ER CORD GND and SIGNAL CA-
(over 26 inch) BLE GND.
- Hi-pot Test PO ER CORD GND and LIVE NEU-
TRAL.
41 R 4) LEAKAGE CURRENT: At 0. mArms
( hite Balance Ad . coordinate and color temperature)
The spec of color temperature and coordinate.
Color Cool , 00 K 0.274 ( 0.0 ) Test Signal
Temperature Y 0.278 ( 0.0 ) - Inner pattern
for /B ad ust
A
Medium 8,000 K 0.2 0 ( 0.0 ) - E ternal hite Measurement condition:
Y 0.2 8 ( 0.0 ) pattern 1) RF input: Mono, 1 KHz sine ave signal, 100 Modulation
arm 6, 00 K 0. 18 ( 0.0 ) (80IRE, 204gray) 2) CVBS, Component: 1 KHz sine ave signal 0. Vrms
Y 0. 4 ( 0.0 ) ) RGB PC: 1 KHz sine ave signal 0.7 Vrms
Luminance Cool Min : 80 Typ : 110 Test Signal No. Item Min Typ Ma Unit Remar
(cd/m ) Inner pattern Audio practical
Medium Min : 80 Typ : 110 (204gray,80IRE) (1) Measurement condition
ma Output, L/R
1 4. .0 6.0 Vrms - E /AVL/Clear Voice: Off
arm Min : 70 Typ : 110 (Distortion 10
(2) Spea er(8 Impedance)
ma Output)
Copyright LG Electronics. Inc. All right reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
9 US S D S 1 O
1) Put the USB Stic to the USB soc et. 1 1 M ADC C
2) Automatically detecting update le in USB Stic . Enter E AD UST mode by pressing AD ey.
- If your do nloaded program version in USB Stic is Lo , it Enter Internal ADC calibration mode by pressing or OK
didn t or . But your do nloaded version is High, USB data ey at ADC Calibration
is automatically detecting.(Do nload Version High Po er
only mode, Set is automatically Do nload)
) Sho the message Copying les from memory .
1 2 A
(1) Set TV in Ad . mode using PO ER ON
(2) ero Calibrate the probe of Color Analyzer, then place it on
the center of LCD module ithin 10cm of the surface.
( ) Press AD ey E ad ust using ad . R/C hite Bal-
ance then press the cursor to the right (KEY ). hen
KEY( ) is pressed 216 Gray internal pattern ill be
displayed.
(4) One of R Gain / G Gain / B Gain should be ed at 1 2,
and the rest ill be lo ered to meet the desired value.
( ) Ad . is performed in COOL, MEDIUM, ARM modes of
color temperature.
Copyright LG Electronics. Inc. All right reserved. - 11 - LGE Internal Use Only
Only for training and service purposes
TROU LE SHOOTIN
1 NO PO ER-M PC A
NO PO ER
YES
YES
YES
4
Chec Line short or open bet een
NO
Check waveform of X501 IC 01 and 01,
Change IC 01 or change 01
YES
YES
6
is there any waver at 11pin of P120, NO change IR board
when use remote controller? Or chec Line short or open of P120
Insert F/ 4
X501
Copyright LG Electronics. Inc. All right reserved. - 12 - LGE Internal Use Only
Only for training and service purposes
2 N P LED
NO RASTER
(Screen is not displayed)
YES
Chec Line short or open bet een
2 Is 1.8V at L501? NO IC711/IC704 and IC 01,
Is 1.25V at L500? If there is any problem at Line,
Change IC711/IC704 or change IC 01
YES
NO
It is not over 2V at Pin of IC 01.
is 2V at 3pin of IC901?
Change IC 01.
YES
Copyright LG Electronics. Inc. All right reserved. -1 - LGE Internal Use Only
Only for training and service purposes
A N A -M PC A
Abnormal/No screen
(all input)
YES
If is not under 1. V at R722,
change 721 or chec open and short
2 NO of Line among 720 and 721.
Is 12V at 1pin of P101? If is under 11V at L110,
Chec open and short
Of line bet een L110 and P101.
YES
YES
Change module
AVE ORMS
Copyright LG Electronics. Inc. All right reserved. - 14 - LGE Internal Use Only
Only for training and service purposes
4 A TV -M PC A
YES
If 1.7V is not at plus pin of TU401, chec
2 NO It is over V at 2pin of IC401,
Is 1.8V at 7pin of TU401? if it is not, Chec Line bet een TU401
and IC401 is open or short.
Another is change IC401 or TU401
AVE ORMS
4
Copyright LG Electronics. Inc. All right reserved. -1 - LGE Internal Use Only
Only for training and service purposes
5 A AV -M PC A
Abnormal screen (AV)
1 NO
Put into AV cable completely? Insult AV cable tight
YES
YES
YES
Change IC 01
AVE ORMS
R505 (CVBS)
Copyright LG Electronics. Inc. All right reserved. - 16 - LGE Internal Use Only
Only for training and service purposes
A R PC -M PC A
Abnormal screen (RGB PC)
YES
YES
YES
Change IC 01
AVE ORMS
Copyright LG Electronics. Inc. All right reserved. - 17 - LGE Internal Use Only
Only for training and service purposes
A HDMI -M PC A
Abnormal screen (HDMI)
YES
YES
Can read EDID and Chec Line bet een K204 and IC 01
HDCP key though is open or short, Another is
16,15pin of JK204 Change HDMI cable
YES
YES
YES
Chec Line bet een K204 and IC 01
6 Is waveform at 1,3,4,6,7,9pin NO
is open or short, Another is
Of JK204? Change HDMI cable
YES
Change IC 01
Copyright LG Electronics. Inc. All right reserved. - 18 - LGE Internal Use Only
Only for training and service purposes
N -M PC A
NO sound (All source)
1
NO
Does wire connect P301 with speaker? Connect ire bet een P 01 and spea er.
YES
If 8V is not plus at L70 , chec
2 of K700 is open.
Is 19.4V at 19,20,31,32pin NO
If is not Chec Line bet een L70
of IC301 ? and IC 01 is open or short.
.Another is change IC 01
YES
If V is not plus 0pin of IC 01,
NO chec It is over V at L 01
Is 3.3V at 40pin of IC301? if it is not, Chec Line bet een L 01
and IC 01 is open or short.
Another is change IC701,IC 01
YES
4
Chec Line bet een IC 01 and IC 01
Is I2C waveform at NO
is open or short, Another is change
10,11pin of IC301?
IC 01 or IC 01.
YES
Copyright LG Electronics. Inc. All right reserved. -1 - LGE Internal Use Only
Only for training and service purposes
9 A TV -M PC A
YES
AVE ORMS
4
Copyright LG Electronics. Inc. All right reserved. - 20 - LGE Internal Use Only
Only for training and service purposes
1 A AV -M PC A
Abnormal sound (AV)
1 NO
Put into AV cable completely? Insult AV cable tight
YES
YES
Change IC 01
AVE ORMS
C520,C521(audio in)
Copyright LG Electronics. Inc. All right reserved. - 21 - LGE Internal Use Only
Only for training and service purposes
11 A HDMI -M PC A
Abnormal sound (HDMI)
YES
YES
Can read EDID and Chec Line bet een K204 and IC 01
HDCP key though is open or short, Another is
16,15pin of JK204 Change HDMI cable
YES
YES
YES
Chec Line bet een K204 and IC 01
6 Is waveform at 1,3,4,6,7,9pin NO
is open or short, Another is
Of JK204? Change HDMI cable
YES
Change IC 01
Copyright LG Electronics. Inc. All right reserved. - 22 - LGE Internal Use Only
Only for training and service purposes
LOC DIA RAM
Copyright LG Electronics. Inc. All right reserved. -2 - LGE Internal Use Only
Only for training and service purposes
EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts
are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as recommended
in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
910
900
400
535
LV1
A2
120
820
540
800
200
300
511
302
510
501
Copyright © LG Electronics. Inc. All right reserved. - 24 - LGE Internal Use Only
Only for training and service purposes
EAX65327301
29MN33A
[RD1]E-LUG
6B IR & LED C126
4.7uF 1
R120 R121 10V
R122 JP120
3.3K 3.3K
100
2
5B [RD1]C-SPRING KEY1
C121 JP121
ROUT KEY2
R123
100
0.1uF
16V
3
D121
JP122
20V
D120
C120
20V
4B [RD1]CONTACT 0.1uF
16V 4
JP123
EEP_SCL 5
5A [WH1]C-SPRING JP124
LOUT +3.5V_ST
EEP_SDA 6
JP125
R124
6A [WH1]E-LUG 100
7
READY JP126
R125
100
8
6G [RD3]E-LUG JP127
9
C JP128
R126
10K B Q120 10
5G [RD3]C-SPRING LED_B MMBT3904(NXP)
JP129
RIN READY
R127
E
11
10K
100pF 50V
100pF 50V
D126 20V
20V
[RD3]CONTACT
READY
READY
4G
C122
C123
12
D127
13
5F [WH2]C-SPRING
LIN
JP108
5E [RD2]C-SPRING
COMPONENT
COMMON_R R130
100
COMPONENT
ZD105 R145 IR
SD05
[RD2]E-LUG-S 75
D123
C124 JP130
20V
7E ZD106
SD05 +3.5V_ST 1000pF
50V
COMPONENT
JP131
JP107
5D [BL]C-SPRING
COMPONENT
COMMON_B C125
ZD103 COMPONENT D124
R146 4.7uF
SD05 5.6V
4C [GN]CONTACT ZD104
75 10V
SD05
COMPONENT
5C [GN]C-SPRING
6C [GN]E-LUG
P101
10031HR-30
LVDS
12.12.19. ESD(Add zenerDiode)
3
JK101 33A
4
PPJ234-03 AV_IN/OUT 5
6E [YL]E-LUG
6
RXA3+
12.12.18 : ESD(Add to zener diode) 7
RXA3-
5E [YL]O-SPRING 8
COMMON_VIN 9
RXACK+
ZD101 10
R101
SD05 RXACK-
4E [YL]CONTACT JP103 ZD102
75
11
SD05
12
RXA2+
13
5D [WH2]O-SPRING JP101
R106
RXA2-
10K AUDIO_LIN 14
18
RXA0+
5C [RD2]O-SPRING JP102
R103 19
RXA0-
10K C101
AUDIO_RIN 20
D102 R102 R104
20V 220K 12K 1000pF
21
7C [RD2]E-LUG-S 50V R110
RIN 22
10K
+3.3V_M
23
C104
10uF R111
5B [WH1]O-SPRING JP104
R108
10V 24 10K
READY
C103 1K MNT_LOUT 25
D104 5600pF C B 26
[WH1]E-LUG-S
20V 50V
E MUTE_AOUT
7B READY R112
3.9K
POP NOISE 27 PANEL_VCC
Q101 28
MMBT3904(NXP)
LOUT 29
JP110
4A [RD1]CONTACT
30
READY
C106 C112
10uF 31 10uF
5A [RD1]O-SPRING JP105
R109
10V 16V
C105 1K MNT_ROUT
D105 5600pF C B
[RD1]E-LUG
20V 50V
E MUTE_AOUT
6A READY R113
3.9K POP NOISE
Q103
MMBT3904(NXP)
ROUT
C opyright ⓒ 201 4 LG Elec tronic s . Inc . All right res erved. LG E Internal Us e Only
Only for training and s ervic e purpos es
EAX65327301
29MN33A
JK201
SPG09-DB-010
RGB Change the Doide from EAH39491601 to EAF61771401
D201,D202,D203
2013.11.26
HDMI1 R231
1K
C
R230
10K B Q230
HDMI1_HPD
R202
R203
MMBT3904(NXP)
R201
RGB
RGB
RGB
75
75
75
Change the Doide from EAH39491601 to EAF61771401
D201 E
D202
D203
D200,D231
RGB
RGB
RGB
2013.11.26
+5V_USB
6 RED_GND GND_R
HDMI1_DET
GND_2
D231
SHIELD
1 11 RED 20
COMMON_R 19 HPD Change the Doide from EAH39491601 to EAF61771401
R234 R235
GREEN_GND JP220 GND_G
18 +5V_POWER
4.7K 10K D232,D233
2013.11.26 R232 R233
7 2.7K 2.7K
D200
R204
DDC_DATA
READY
33 17 DDC/CEC_GND
2 12 JP204
GREEN JP221 16 SDA HDMI1_SDA
BLUE_GND JP222 GND_B
DSUB_G 15 SCL
JP205
HDMI1_SCL
8 14 NC
D233
RGB D234
D232
R205
H_SYNC 33 13 CEC READY RCLAMP0544T.TCT
6.5VTO11.0V
3 13 DSUB_HSYNC
12 CLK- 1 8
BLUE JP223
HDMI1_CK-
COMMON_B 11 CLK_SHIELD
NC JP224 2 7
9 RGB 10
CLK+ HDMI1_CK+
V_SYNC R206 DATA0- 3 6
4 14
33
DSUB_VSYNC
9 HDMI1_D0-
GND_1 8
DATA0_SHIELD 4 5
JP225
DATA0+ HDMI1_D0+
+3.5V_ST 7
SYNC_GND DATA1- 9
10 RGB
6
DDC_CLOCK
JP226 R207
R208 DATA1_SHIELD 1 8
5 15
33
10K
5
DATA1+
HDMI1_D1-
DDC_GND
JP227
4 2 7
DSUB_DET 3 DATA2-
HDMI1_D1+
3 6
DATA2_SHIELD
HDMI1_D2-
RGB C203 68pF
2
RGB R212 22K
READY
C201 DATA2+ 4 5
JP228
68pF 1
HDMI1_D2+
D205
D206
50V
16 READY
D204
D207
D208
C202
SHILED 68pF
50V
D235 9
JK203 RCLAMP0544T.TCT
6.5VTO11.0V
RGB
RGB
RGB
1.RED
READY
2.GRN
Change the Doide from EAH39491601 to EAF61771401
3.BLU D204,D205,D206,D207,D208
4.NC 2013.11.26
+5V_USB
5.ST-DET
7.GNC R210
8.B_GND 4.7K
9.G_GND DSUB_SCL
10.R_GND
11.GND DSUB_SDA
12.SDA R209 READY
4.7K READY
13.HSYNC C205 C206
14.VSYNC 18pF 18pF
50V 50V
15.SCL
C221
22uF
6.3V
3AU04S-305-ZC-(LG)
JK701
JP208
USB DOWN STREAM
USB_DN
2
JP209
USB_DP
3
C opyright ⓒ 201 4 LG Elec tronic s . Inc . All right res erved. LG E Internal Us e Only
Only for training and s ervic e purpos es
EAX65327301
29MN33A
SW_RESET
C320
1000pF
50V
+19V
50V
I2S_MCLK R304 100
22000pF
C319
+3.3V_M
[EP]GND
10V
VDD_IO
GND_IO
PGND1A
PVDD1A
PVDD1B
R313 R314 SPK_L+
L303
CLK_I
RESET
BST1A
OUT1A
12 12
10uH
C330 R322
0.1uF 4.7K
C325 50V
AD
390pF
50V
C329
C326 0.47uF
50V
SPEAKER_L
390pF
50V C331 R323
L304
40
39
38
37
36
35
34
33
32
31
0.1uF
10uH 50V 4.7K
R315 R316 SPK_L-
AGND_PLL 1 30 OUT1B 12 12
I2S_WS
R302 100 8 23 1uF SPK_R+ SPK_R+
2
10V JP301
R303 100 BCK 9 22 PGND2A C311
SPK_R-
I2S_SCK 22000pF SPK_R- 1
AUAMP_SDA
SDA 10 21 OUT2A 50V .
11
12
13
14
15
16
17
18
19
20 SMAW250-H04R
P301
AUAMP_SCL
READY READY
SCL
FAULT
MONITOR_0
MONITOR_1
MONITOR_2
BST2B
PGND2B
OUT2B
PVDD2B
PVDD2A
POWER_DET
C341
0.1uF
25V Q341
MMBT3904(NXP)
C
E
B R342 1K 1 OUT1 OUT4 14
C342
R343 10K
MNT_LOUT 0.0068uF
50V
R341
4.7K C343 33pF 50V 2 INPUT1- INPUT4- 13
R344
6.8K
MNT_L_AMP
R345 5.6K 3 INPUT1+ INPUT4+ 12
+18V
4 VCC GND 11
C344
0.1uF
25V
MNT_R_AMP
R346 5.6K 5 INPUT2+ INPUT3+ 10
+18V C345 33pF 50V
C opyright ⓒ 201 4 LG Elec tronic s . Inc . All right res erved. LG E Internal Us e Only
Only for training and s ervic e purpos es
EAX65327301
29MN33A
IF
PAL_ISOLATOR
NTSC
+3.3V_TU
TU401 TU402
TDSH-G501D(B) TDSS-H501F(B) R404
100K
R403
100
TUNER_RESET
C401
0.1uF
NC NC_1 16V +3.3V_TU
1 1
RESET RESET R407
2.2K
R408
2.2K
2 2
TUNER_SCL
SCL SCL C402
3 3 47pF
50V
C404 R410
C405 1
SIF NC_2 0.1uF
16V
22uF
6.3V
C411
0.1uF
C412
10uF
6 6 1/10W
+1.8V_M
16V
10V
9 9 10uF
10V
B1 A1 B1 A1 NTSC
R413-*1
C410
0.1uF
should be guarded by ground
B1 A1 B1 A1 0
16V
PAL
R413
10
PAL
IF_P
B2 A2 12 R414
10
PAL_NON_ISOLATOR
IF_N
B2
A2
NC_1
1
READY
0 R401 RESET
2
SCL
READY 3
0 R402 SDA
4
3.3V
5
NC_2
6
1.8V
7
NC_3
8
IF_AGC
9
DLIF_[P]
10
DLIF_[N]
11
B1 A1
B1 A1
12
SHIELD
C opyright ⓒ 201 4 LG Elec tronic s . Inc . All right res erved. LG E Internal Us e Only
Only for training and s ervic e purpos es
AUAMP_SCL
EAX65327301
AUAMP_SDA
BLU_CURRENT_CTL
HDMI1_SDA
HDMI1_D0+
HDMI1_D0-
HDMI1_CK+
HDMI1_HPD
SW_RESET
HDMI1_CK-
HDMI1_D1+
HDMI1_D1-
+3.3V_ST
*H/W OPTION
MUTE_AOUT
HW_RESET
I2S_MCLK
HD FHD
29MN33A
IR
LED_B
HW_OPT LOW HIGH
MSTAR Vcc
PWM_DIM
DSUB_SDA
DSUB_SCL
KEY2
KEY1
+1.8V_M
2.2uF
READY
C552
R519
4.7K +3.3V_M
GPIO69/I2S_OUT_MCK
R544
R543
33
33
10K
R542
R535 1K
R541 FHD
100 100
READY
R518 R550 +1.2V_VDDC
100 R545
100
C549 R540
0.1uF 1K
R537
22
R536
22
4.7K C501 ST 1.26V
33
R531
10uF
R505
HW_OPT1 10V
C553 HD
0.1uF
SAR3/GPIO72
SAR2/GPIO73
SAR1/GPIO74
SAR0/GPIO75
PWM1/GPIO25
PWM0/GPIO26
R551
AVDD_DDR_2
R534 4.7K
R546
HOTPLUG_D
100 1K
DDCDD_DA
RXCKP_D
RXCKN_D
HWRESET
DDCA_DA
DDCA_CK
TESTPIN
R533
RX1P_D
RX1N_D
RX0P_D
RX0N_D
GPIO70
GPIO68
GPIO67
0
DDR 1.8V
[EP]
IRIN
+1.8V_M
GND
CEC
C503
22uF
6.3V
INV_ON
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
READY
R522 100
R500 DDCDD_CK 1 102 GPIO64
HDMI1_SCL
33
RX2N_D 2 101 GPIO63 +3.3V_ST
HDMI1_D2-
RX2P_D
THERMAL
AVDD_MOD_4
C548
0.1uF
ST 3.3V
HDMI1_D2+ 3 129 100 L502
+3.5V_ST +3.3V_ST
HOTPLUG_A 4 99 USB0_DP BLM18PG121SN1D
USB_DP C504
10uF
RXCKN_A 5 98 USB0_DM 10V
USB_DN
RXCKP_A 6 97 SPI_CZ
SPI_CZ
RX0N_A 7 96 SPI_DO
SPI_DO
RX0P_A 8 95 SPI_DI
SPI_DI
AVDD_MOD_1 9 94 SPI_CK
+3.3V_ST SPI_CLK
C505
0.1uF
RX1N_A 10 93 PWM3/GPIO25 FLASH_WP
RX1P_A 11 IC501 92 PWM2/GPIO24 R549 READY
33 EEPROM(256K)
IC503
EEPROM_RENESAS
IC503-*1
M24256-BRMN6TP
EEPROM_ST
E0 VCC
2
8
7
WC
10K
RX2N_A GPIO1
LGE6841 (ATV_13)
E2 SCL
SDA
1 8 4 5
R506
+3.3V_ST
C513 SO/SIO1 HOLD
SCLK
3 6
W25Q64FVSSIG
68 0.047uF
CVBSOUT1 LVBCKM
R581
29 74
10K
CS VCC
+3.3V_ST C515 AVDD_AU33 LVBCKP SPI_CZ
R571 FLASH_WINBOND
1 8
0.1uF 30 73 100 C575
L506 AUREF 31 72 LVB3M SPI_DO
R572 DO[IO1]
2 7
%HOLD[IO3] 0.1uF
16V
C516 C517 100
120-ohm 10uF
16V
0.1uF VAG 32 71 LVB3P R576 WP[IO2] CLK R574
FLASH_WP 3 6 SPI_CLK
100
LINEIN_L1 33 70 LVB4M 100
GND DI[IO0] R575
4 5 SPI_DI
LINEIN_R1 34 69 LVB4P 100
C576
C520 2.2uF LINEIN_L3 35 68 LVA0M 0.1uF
AUDIO_LIN
RXA0- RXA0- 16V
C522 R510 C521 2.2uF LINEIN_R3 36 67 LVA0P READY
220pF 220K AUDIO_RIN
RXA0+ RXA0+
R508
100 LINEOUTL3 37 66 LVA1M
MNT_L_AMP RXA1-
RXA1-
LINEOUTR3 38 65 LVA1P
MNT_R_AMP RXA1+
R509 RXA1+
100
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
C523 R511
220pF 220K
+3.5V_ST H/W RESET
XTALO
XTALI
AVDD3P3_DMPLL
AVDD3P3_DADC
VIFP
VIFM
IFAGC
VSS
AVDD_DDR
GPIO55/I2S_OUT_WS
GPIO56
GPIO57/I2S_OUT_BCK
GPIO58/I2S_OUT_SD
GPIO60
GPIO61
VDDP
VDDC_1
LVA4P
LVA4M
LVA3P
LVA3M
LVACLKP
LVACLKM
AVDD_MOD_2
LVA2P
LVA2M
IC504 R561
JP501
JP502
JP503
JP504
APX803D29 10K
GND
33
R520
33
R521
1M
RXACK-
470
RXACK+
RXA2+
RXA3+
RXA3-
RXA2-
C542 C560
0.1uF 0.1uF
+3.3V_ST
X501 C561
4.7uF
24MHz 4.7uF
R513
C562
R514 R517 +1.8V_M 10V
10V
100 100 10K R564
I2S_SCK
0
I2S_SDO
RXACK-
HW_RESET
RXA3+
RXA3-
RXA2-
TUNER_RESET
RXA2+
RXACK+
I2S_WS
R524
C531 C534 C535
TUNER_SCL
C530 0 C563
TUNER_SDA
+3.3V_M
R563
62K
15pF 15pF 0.1uF READY 0.1uF 0.1uF
C551 16V
220pF
50V
C541
C536 C537 0.022uF
33pF 33pF 16V
C544 C545
C536,C537 : 390pF->33pF L521 0.1uF
+1.2V_VDDC
IF_N
C opyright ⓒ 201 4 LG Elec tronic s . Inc . All right res erved. LG E Internal Us e Only
Only for training and s ervic e purpos es
EAX65327301
29MN33A
+19V
L901 D901 L601 L602 D603
33uH BR210 VOUT#1=53.2V 33uH 33uH UF3D(SUZHOU GRANDE)
REDUCE RIPPLE CURRENT
100V
C902 C903 C913 R920
C901 C911 C912 100K
47uF 10uF 0.1uF 33uF 33uF 1uF 1/8W
25V 25V 50V 100V 100V 50V
READY
C905
R909 R911
100pF 220K 30K
C914 R921
1uF 100K
50V 1/16W 1/16W 1/8W
50V
IC901
+5V_USB
READY
TPS40210DGQR [EP] C918
250V
560pF READY
R601 R603 R604
RC VDD READY 10K 3K
READY R918 1K +19V NEW_02
1 10 R917 20 D
20 IC600
THERMAL
C 1% R605 C601
R906 C907 R602 Q603
0.22uF SS BP 100K 1000pF DT1641AS [EP]GND
11
BOOST_EN
R903
1K DIS/EN
3 8
GDRV
R913
3.3 G
Q902
AOD478 INV_ON E EN
1 24
VIN
D
Q603-*1
G SMK630D
THERMAL
S
R914 R626 R600
COMP ISNS OVP VREF C622 1uF
25
3.9K 120K 270K S
4 7 2 23
1% 1/8W 1/8W CMI_OLD 25V
R628 C614
FB GND 1% 1% 1000pF NC_1 CS
5 6 6.2K 3 22
CMI_NEW 1% 50V 2014.01.07 BS.HAN
C908 C909 C910
READY
R628-*1
R915
R916
0.1
1W
1% 7 18
18K
1% CMI_OLD
BLU_CURRENT_CTL CMI_NEW R624 R637
R624-*1 30K LS8 LS1 R635 C625
20K 8 17 0.1
R905 1%
1% 1.5K 1%0.1uF 1%
1K CMI_OLD
CMI_NEW R625 25V
R625-*1 2K LS7 LS2 1W
1% 560 9 16
VOUT = VREF*(1+51K/680) 1%
1%
= 0.7 *(1+51K/680) LS6 LS3
R631
39K
10 15
= 53.2V R907 1%
680
1/8W LS5 LS4
1% 11 14 R633
1.5K
10K
1%
R647
NC_2 LGND
12 13
ZD602
33V
FIRST BOOST UP
C629 R648 C627
33uF 1M 1uF
100V 1/8W 100V
1%
JP601
C630 C628
P601 R649
33uF 1M 1uF
SMAW200-03 3 1/8W
100V 1% 100V
2 JP602
1
VOUT#2
C opyright ⓒ 201 4 LG Elec tronic s . Inc . All right res erved. LG E Internal Us e Only
Only for training and s ervic e purpos es
EAX65327301
29MN33A
19V TO ST3.3V DCDC CONVERTER
+19V
IC701
MP2315GJ
R702
100K
** 3.5V_ST -> 1.26V VDDC
R701 R705 V0 = 0.8*(1+(R2/R1))
JK700
JP701 47K AAM
1 8
FB 33K +3.5V_ST IC704
KJA-DC-1-0032 AP7173-SPG-13 HF(DIODES)
+3.5V_ST +1.2V_VDDC OUT:1.26V
4 IN VCC [EP]
4 2 NEW 7
L702
3A
10uH
2 2 C701 C703 C704 SW EN/SYNC IN OUT
68uF 10uF 0.1uF 3 6 1 8
25V
THERMAL
35V 25V
C706 R706
ZD702
1 1 GND BST 20130528 cJ.LIM 0.1uF C707 C708 C709 2013.08.07 PG FB R1
9
4 5 2 7
5V
22uF 10uF 0.1uF 5.1K 5.6B->5V
25V 25V C742
R704 6.3V 10V READY->APPLY 1%
R703 1% 10uF
68 20K 20130528 cJ.LIM 1% R740
R707 VCC SS R741 10V
3 6 2.7K
27K
4.7K
JP702 C705 C746
1% R744 560pF
0.1uF 10K EN GND 50V
50V 4 5
C740
R708 10uF
10K 10V
1%
READY +18V
READY READY C745
C715
D711
R711 R715 C714
18V
0.1uF 47uF 10uF
33K 470
25V 25V 10V
G
Q712
AO3407A
READY READY
R713
READY
5.6K
R710 C
10K
B
+3.3V_M
READY
R716
Q713
E MMBT3904(NXP)
READY
** +3.5V_ST -> 3.3V_M
7.5K
+3.5V_ST
Q710
AO3435
D
+3.3V_M
R750
10K
19V TO PANEL VCC(12V/5V) DCDC CONVERTER
R723 R749
4.7K POWER_SW 2.2K
IC702 READY
C724
BOOST_EN
MP2315GJ 0.47uF
16V C
R747
10K B Q711
R720 R724
47K AAM FB 33K POWER_SW MMBT3904(NXP)
1 8
L720 E
15uH
IN VCC
+19V 2 NEW 7 P_12V FET Multi_NXP
Q720-*3
FET Multi_DIODES_B
Q720-*4
PMV48XP DMP2130L
3A
ZD701
READY
C727
15V
D
S
D
10uF 0.1uF 3 6 10uF 10uF 0.1uF 43K
25V 25V 1%
25V 16V 16V
C723
GND BST 0.1uF
20130528 cJ.LIM READY
G
4 5
G
25V R726
R722 100K FET Multi_DIODES_A FET Multi_AOS_B
R721 20K 1%
68 Q720-*1 Q720-*2
ZXMP3F30FHTA
C722 ** Switch Panel-Vcc AO3407B
D
0.1uF R727
10K
50V 1%
P_12V
G
FET Multi_AOS_A
Q720 PANEL_VCC
AO3407A
D
C761 READY
0.1uF R765 R766
16V 3.3K 4.7K
R761 C760
G
22K 1uF
25V
R771
19V TO USB 5V DCDC CONVERTER 20K
3 6 0.1uF
5.6B
C773 1%
GND BST 0.1uF R776
4 5 20130528 cJ.LIMREADY
25V 33K
R773
R772 20K 1%
68
C772 R777
0.1uF 15K
50V
1%
C opyright ⓒ 201 4 LG Elec tronic s . Inc . All right res erved. LG E Internal Us e Only
Only for training and s ervic e purpos es