Professional Documents
Culture Documents
ECO
Service Manual
Page
PRECAUTIONS 3
SPECIFICATIONS 4
TIMING CHART 5, 6
OPERATING INSTRUCTIONS 9, 10
SERVICE MODE 11
WIRING DIAGRAM 12
DISASSEMBLY 13
ADJUSTMENT 14
EXPLODED VIEW 15
• Do not modify original design without obtaining written • If you want to replace with the new backlight
permission from manufacturer or you will void the (CCFL) or inverter circuit, must disconnect the
original parts and labor guarantee. AC adapter because high voltage appears at
inverter circuit about 650Vrms.
TAKE CARE DURING HANDLING THE LCD
MODULE WITH BACKLIGHT UNIT. • Handle with care wires or connectors of the
inverter circuit. If the wires are pressed cause
• Must mount the module using mounting holes short and may burn or take fire.
arranged in four corners.
• Do not press on the panel, edge of the frame strongly Leakage Current Hot Check Circuit
or electric shock as this will result in damage to the
screen.
2. OPTICAL CHARACTERISTICS
Digital
Horizontal : 28 ~ 75kHz
Vertical: 60Hz
Dot clock :< 165MHz
4. Max. Resolution
Analog / Digital: 1600 x 1200 / 60Hz
*3. Change decimal-seven-digit serial number to the ACII code and input it by unit.
Ex) 5000001-> 35,30,30,30,30,30,31
*4. Input the data as the value of the lower 8 bits of the sum up all registers from #0 to #126 is equal to
"00h".
Ex) The sum of data from #0 to #126 is "1C2Bh". In this case, the check sum is "D5h",
2Bh+D5h=100h
*3. Change decimal-seven-digit serial number to the ACII code and input it by unit.
Ex) 5000001-> 35,30,30,30,30,30,31
*4. Input the data as the value of the lower 8 bits of the sum up all registers from #0 to #126 is equal to
"00h".
Ex) The sum of data from #0 to #126 is "1C2Bh". In this case, the check sum is "D5h",
2Bh+D5h=100h
2. MENU Button
This button turns the menu screen on and off.
4. OK Button
This button activates the selected menu item and
adjustments made using the buttons (3).
INPUT
These buttons switch the video input signal between
INPUT1 and INPUT2 when two computers are connected
to the display. (Only available when menu is turned off.)
5. ECO Button
This button is used to reduce the power consumption.
When the menu screen is not displayed, you can also
automatically adjust the picture quality for the current input
signal while keeping pressing this button for more than 3
seconds (One touch Auto adjust). (Analog RGB signal
only)
6. Light sensor
This sensor measures the brightness of the area
surrounding the display. Be sure not to cover the sensor
with paper, etc.
7. Headphone jack
This jack output audio signals to your headphone.
11. AC IN connector
This connector connects the power cord (supplied).
「COLOR TEMP」
You can set color temperature (Factory Setting Area).
「INITIAL EEPROM」
You can initialize micro computer data. Therefore, COLOR TEMP data becomes the default “128”. User
table data is reset.
「CLR. ETI」
ETI is reset, “0 H”.
「AGING」
You can change aging status ON/OFF. Default is OFF.
「WHITE BALANCE」
There are ADC(Analogue Digital Converter) calibration function and ADC MANUAL calibration function.
ADC calibration function adjustment is required when A (Main) board is replaced. Bias is usually input
on supplied service boards. MANUAL calibration function is rarely used.
* When ADC calibration is enforced, please calibrate with WHITE WINDOW pattern of Analogue VGA
signal.
** Input Signal: 31.4kHz, 600×480/60Hz and 0.73VP-P (75Ω terminate)
「DEFAULT TIMING」
You can select 1152×870 or 1152×864. Default is 1152×870.
「MODULE」
You can select γ (table) corresponded to each module.
When you replace A board or Panel, it is required to set the Panel inch size and the Panel maker name
on selecting “MODULE”.
⑬
⑲
⑰
⑫
⑳
⑦
⑤ ⑪
⑥
⑩
⑧
③
①
②
S205x
*Please refer to the following URL of TV QA web page to see the latest service parts list.
http://www.tvqa.sony.co.jp/index(E).htm
“TVQA Common” Æ “Flat TV: ID Parts Information”