Professional Documents
Culture Documents
com
E-mail:http://www.LGEservice.com/techsup.html
COLOR MONITOR
SERVICE MANUAL
CHASSIS NO. : CL-32
FACTORY MODEL: LB500K
MENU
AUTO/SEL
ECT
CONTENTS
SPECIFICATIONS ................................................... 2 TROUBLESHOOTING GUIDE .............................. 13
PRECAUTIONS ....................................................... 3 PRINTED CIRCUIT BOARD................................... 17
TIMING CHART ....................................................... 4 EXPLODED VIEW...................................................18
OPERATING INSTRUCTIONS ................................ 5 REPLACEMENT PARTS LIST ...............................20
WIRING DIAGRAM ................................................. 6 PIN CONFIGURATION............................................23
BLOCK DIAGRAM ................................................... 8 SCHEMATIC DIAGRAM (LGP MODULE) .............. 25
ADJUSTMENT ...................................................... 12 SCHEMATIC DIAGRAM (AUO MODULE) ............. 31
SPECIFICATIONS
1. LCD CHARACTERISTICS 3-3. Operating Frequency
Type : TFT XGA LCD Module Horizontal : 30 ~ 63kHz
Size : 352.0(H) x 263.5(V) x 14.0(T) Vertical : 56 ~ 75Hz
Pixel Pitch : 0.297mm x 0.297mm
Color Depth : 6bits(with FRC)/ 16M colors (LPL Module) 4. POWER SUPPLY
: 6bits / 262,144 colors (AUO Module) 4-1. Power
Active Video Area : 15.0inch 100~240V, 50/60Hz 0.6A
(304.128 x 228.096)
Surface Treatment : Anti-Glare, Hard Coating (3H) 4-2. Power Consumption
Backlight Unit : Top/Bottom edge side 2CCFL
Electrical Interface : LVDS interface (LG Philips Module) MODE H/V SYNC VIDEO POWER CONSUMPTION LED COLOR
: TTL interface (AUO Module) POWER ON (MAX) ON/ON ACTIVE less than 30 W GREEN
-2-
PRECAUTION
WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING
• There are some special components used in LCD BE CAREFUL ELECTRIC SHOCK !
monitor that are important for safety. These parts are
• If you want to replace with the new backlight (CCFL) or
marked on the schematic diagram and the
inverter circuit, must disconnect the AC adapter
replacement parts list. It is essential that these critical
because high voltage appears at inverter circuit about
parts should be replaced with the manufacturer’s
650Vrms.
specified parts to prevent electric shock, fire or other
hazard.
• Handle with care wires or connectors of the inverter
• Do not modify original design without obtaining written circuit. If the wires are pressed cause short and may
permission from manufacturer or you will void the burn or take fire.
original parts and labor guarantee.
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.
-3-
TIMING CHART
VIDEO
B A
E
C
F
D
SYNC
-4-
OPERATING INSTRUCTIONS
MENU
AUTO/SELECT
Power Connector
See front control panel D-Sub Signal Connector
2 3 4 1
amber.
2. Menu Button When adjusting your display settings, always
Use this button to enter or exit the On Screen press the AUTO/SELECT button before entering
Display. the On Screen Display(OSD). This will
automatically adjust your display image to the
3. Button ideal settings for the current screen resolution
size (display mode).
Use these buttons to choose or adjust items in the
On Screen Display. The best display mode is 1024x768.
100
Bring up Contrast and
100
Brightness adjustment.
-5-
WIRING DIAGRAM (LG Philips Module)
Connector Ass’y :
P/N: 6631T11016C
Connector Ass’y :
P/N: 6631T20008U
J702
J706
J705
CN2
CN3
J1
-6-
WIRING DIAGRAM (AUO Module)
Connector Ass’y :
P/N: 6631T11011H
Connector Ass’y :
P/N: 6631T20008U
J402
J706
J705
CN2
CN3
J1
-7-
EEPROM
E-DDC SCLK
24LC02 MICOM EEPROM
SDATA
(MTV312) 24LC16
D- Schmitt Trigger
H.V Hsyncm 5VR
Sub (74HCT14A)
Vsyncm
15P Hsync2 Vsync2 Control Panel
Inverter on/off DIMADJ
Interface
ADC/PLL/Scaler 20 Pin
RGB 24 Bit LVDS
(GMZAN2) Connector
Inverter on/off
-8-
CON 3.3VD
DIMADJ
3.3VD 3.3V_PL 3.3V_AD 2.5V_A 2.5V_D
8P Regulator 3.3V_A
5VR
BA033
CON 2P 3.3V_PL
BD Regulator
12VS
BA033 +3.3V
SMPS
BLOCK DIAGRAM (LG Philips Module)
PWM Regulator
DIMADJ
Controller BA033 Module Power 3.3V
CON 2P
LIPS
DESCRIPTION OF BLOCK DIAGRAM (LG Philips Module)
1. Scaler One chip IC(GMZAN-2, U201)
GMZAN-2 (U201) is one chip IC which it supports four internal function blocks of Video Amp, PLL,
A/D converter and Video processor.
Video signal (0.7Vp.p) clamped through C207, 208, 209 with matching IC’s proper cut off voltage.
This signal is processed as a proper 8 bit digital signal by U201’s amplifying, phase locking, A/D converting,
and scaling operations.
U201 outputs 24bit RGB data and control signals(Clock, Horizontal and Vertical sync, and Data Enable)
as LVDS IC’s input signals.
1) Microprocessor (U501) distinguishes polarity and frequency by calculating horizontal and vertical sync input
from signal source.
2) Microprocessor (U501) carries out power control by sending power-down trigger signal to each IC.
3) Microprocessor (U501) communicates with EEPROM (U502), and GMZAN-2 (U201)
through IIC(2 lines) or 4 bit bus line. It makes all devices operated properly.
4) Microprocessor (U501) let User adjust screen by OSD function.
LVDS transmitter (U411) delivers digital signal to the receiver inside LCD module by method of abstraction.
The abstracted signals are pairs of RIN0+-, RIN1+-, RIN2+-, RIN3+-, and RCLKIN+- of which voltage swing
is 0.5V each.
When SHUTON pin’s input is High, transmitter goes to power down mode.
4. DC/DC block
This block supplies DC voltages of 5VS to interface board and 12V to inverter by converting AC input voltage
of 100~240Vac.
Converting method is SMPS(Switching Mode Power Supply).
Inverter on/off signal from microprocessor makes inverter turned on or off .
DIMADJ signal from microprocessor does inverter’s current adjustment for Brightness control.
-9-
EEPROM
E-DDC SCLK
24LC02 MICOM EEPROM
SDATA
(MTV312) 24LC16
D- Schmitt Trigger
H.V Hsyncm 5VR
Sub (74HCT14A)
Vsyncm
15P Hsync2 Vsync2 Control Panel
Inverter on/off DIMADJ
Interface
ADC/PLL/Scaler 80 Pin
TTL 36 Bit Two channel
RGB (GMZAN2) Connector
Inverter on/off
3.3VD
- 10 -
CON 3.3VD 3.3V_PL 3.3V_AD 2.5V_A 2.5V_D
DIMADJ
8P Regulator 3.3V_A
5VR
BA033
CON 2P 3.3V_PL
BD
Regulator
12VS +3.3V
BLOCK DIAGRAM (AUO Module)
BA033
SMPS
5VR Regulator +2.5V_A
Filter RC117
Inverter on/off
Inverter on/off
2.5V_D
PWM Regulator
DIMADJ
Controller BA033 Module Power 3.3V
CON 2P
LIPS
DESCRIPTION OF BLOCK DIAGRAM (AUO Module)
1. Scaler One chip IC(GMZAN-2, U201)
GMZAN-2 (U201) is one chip IC which it supports four internal function blocks of Video Amp, PLL,
A/D converter and Video processor.
Video signal (0.7Vp.p) clamped through C207, 208, 209 with matching IC’s proper cut off voltage.
This signal is processed as a proper 8 bit digital signal by U201’s amplifying, phase locking, A/D converting,
and scaling operations.
U201 outputs 36 bit two channel RGB data and control signals (Clock, Horizontal and Vertical sync, and
Data Enable) as LCD panel’s input signals.
1) Microprocessor (U501) distinguishes polarity and frequency by calculating horizontal and vertical sync input
from signal source.
2) Microprocessor (U501) carries out power control by sending power-down trigger signal to each IC.
3) Microprocessor (U501) communicates with EEPROM (U502), and GMZAN-2 (U201)
through IIC(2 lines) or 4 bit bus line. It makes all devices operated properly.
4) Microprocessor (U501) let User adjust screen by OSD function.
4. DC/DC block
This block supplies DC voltages of 5VS to interface board and 12V to inverter by converting AC input voltage
of 100~240Vac.
Converting method is SMPS(Switching Mode Power Supply).
Inverter on/off signal from microprocessor makes inverter turned on or off .
DIMADJ signal from microprocessor does inverter’s current adjustment for Brightness control.
- 11 -
ADJUSTMENT
All adjustment are thoroughly checked and corrected 2. Adjustment for White Balance
when the monitor leaves the factory, but sometimes 1) Display color 0,0 pattern at Mode 13.
several minor adjustment may be required. 2) Set External Bright to MAX position and Contrast to
Adjustment should be following procedure and after MAX Position.
warming up for a minimum of 10 minutes. 3) Select PRESET START → BIAS CAL command
Alignment appliances and tools. and Enter.
4) No attempt to manually adjust, BIAS data is auto-
- IBM Compatible PC
matically adjusted and saved to the EEPROM.
- Programmable Signal Generator.
5) Display color 15,0 pattern at Mode 13.
(eg. VG-819 made by Astrodesign Co.)
6) Select DRIVE CAL command and Enter.
- E(E)PROM with each mode data saved.
7) Color 1 (9300K) and Color 2 (6500K) are
- Alignment Adapter and Software.
automatically adjusted and saved to the EEPROM.
1. Adjustment for Factory Preset Mode 8) Select PRESET EXIT command and Enter.
1) Run alignment program for LB500K on the IBM
compatible PC.
2) Select EEPROM All Init. command and Enter.
3) Display cross hatch pattern at Mode 1.
4) Select EDID WRITE command and Enter.
IBM 9 6
Video Signal 5 1
Compatible PC 15 11
Generator 10 6
5 1
C
PARALLEL PORT
d
13
se
1
tu
25
No
14
2
23
RS
OFF ON
5V
EL
Control Line
F
LL
C
RA
PA
VG ON
WE
S 5V
(110V/220V)
PO
E 74LS06
A
T
MO Power LED
CS
NI OFF 4.7K
YN
TO
V-S
R
74LS06
E ST Switch
B
B
F V-Sync On/Off Switch
(Switch must be ON.)
- 12 -
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
CHECK POWER
CHECK J705 BOARD, AND FIND
NO
VOLTAGE OUT A SHORT POINT
PIN5, PIN6 (5V)? AS OPENING
EACH POWER LINE
YES
CHECK
U802 PIN 1 NO
CHECK U803.
VOLTAGE
(5V) ?
YES
CHECK
NO CHECK 5VS LINE
U805 PIN 1 Voltage
(OPEN CHECK)
(5V) ?
NO PROBLEM
YES
IS U201
PIN12 (3.3V) NO
VOLTAGE REPEATED
AS PULSE
SHAPE ?
NO
- 13 -
2. NO RASTER (OSD IS NOT DISPLAYED) – LIPS
NO RASTER
(OSD IS NOT DISPLAYED)
J705
NO
PIN5, PIN 6 CHECK LIPS
5V?
YES
YES
1. CONFIRM BRIGHTNESS
J705 PIN1 NO OSD CONTRL STATE.
5V? 2. CHECK MICOM DIM-ADJ
PORT
YES
CHECK
PULSE AS
CONTACTING SCOPE
PROBE TO CAUTION LABEL. NO
(CONTACT PROBE TO LIPS
CAUTION LABEL.
CAN YOU SEE PULSE
AT YOUR
SCOPE?
YES
- 14 -
3. NO RASTER (OSD IS NOT DISPLAYED) – gmZAN2
NO RASTER
(OSD IS NOT DISPLAYED)
U201 NO
POWER PINS CHECK U802, U806
3.3V?
YES
YES J402
(AUO Module) PIN63 IS 65MHz CLOCK?
PIN66 IS 48KHz H-SYNC? NO CHECK
PIN70 IS 60Hz V-SYNC? CONNECTION LINE
PIN69 IS 48KHz DEN? FROM U201 TO J402
IS PULSE APPEARED
AT SIGNAL PINS?
YES
(LG Philips Module) YES
J402 NO CHECK
U401/U411 PIN74, PIN 1 U805
PIN31 IS 65MHz CLOCK? 3.3V?
PIN27 IS 48KHz H-SYNC?
NO
PIN28 IS 60Hz V-SYNC? YES
PIN30 IS 48KHz DEN?
IS PULSE APPEARED TROUBLE IN CABLE
AT SIGNAL PINS? OR LCD MODULE
U401 PIN1 NO
CHECK U805
3.3V?
YES
TROUBLE IN CABLE
OR LCD MODULE
- 15 -
4. NO RASTER (OSD IS DISPLAYED) – gmZAN2
NO RASTER
(OSD IS DISPLAYED)
YES
U201
NO
POWER PIN CHECK U802, U806
3.3V?
YES
CHECK 1. CHECK PC
R,G,B INPUT? NO 2. CHECK SIGNAL CABLE
U201 PIN 87, 91, 95 & D-SUB CONNECTOR
LINE
YES
CHECK
NO CHECK H-SYNC LINE
H-SYNC INPUT
(D-SUB→U701→MICOM
U201 PIN 150?
→U201 PIN150)
- 16 -
PRINTED CIRCUIT BOARD
U502
C514 R561
L701
J702
R560 C706
J706
R581
U805
C820
R580
C832
R570
R571
R726
C713
R541
R525
C816
C813
R537
R533
R534
C503
C502
L710
R529 1
C516 X201
R528 C410
R551
R531 C409 C408 C407 C406 R712
R403 R404
C818
C819
Q506
R724
R723
R725
C703
U702
Q502
R713
C403
U701
R510
R715
R727
Q505
L802
L804
L401
C248 C210 C829
R532
R511
D708
C249 C224 C223
C235
R512 C242
C511
C270
ZD501
PANNEL
C402
C212 R206
C712
Q501 160
150 C215 C828 R714
D707
LPL
R535
U802
R401
R539 R711
L703
L702
L705
L704
R540
C501
C401
R710 R733 R716
C817
120
R515
C243
R709
C404
C708
C709
R708
C711
C710
R722
R518 R705
C513
Q503
Q701
ZD701
5
R516 C237 C238 C236
R536
C227 C234
L803
R734
C233 C229 C206
10
R517 C405 C214 D703 D704 D705
110
U401
C731
C218 C231
R526 R202
C247 C217
C512
BA205
U807
C707
C505 C245 C246
X501
C241 C244
R707
R523 C239 C240
C228
BA206
R717
C232
R527 C222 C221 R201 C827
20
C506 C219 C821
R205
C824
100
ZD702
R524
C226
R501 C802
R538
R503 BA202
C508 C258
C801
R504
C230
C262
L204
R505 R519
90
R506 C259
30
R507 R520
R508
R207
C225
C261
C205
R521 L805
R509 C269
BA201
BA203
C826
C515
R703
C257
C715
L707
40
L706
C504
R720
R522
R813
R204
C254 R208
C250
C202 C208
R701
C204
C255 R210 D702
L202
C825
R203
D701
C256 R209 D706
80
C831
60
R706
70
50
C509
BA204
U201
RA501 RA502
C211
C216
J705
L801
MODEL:LB500K
C717
C220
C271
L205
DATE :2002.07.20
J703
C716
L708
P/N :6870T534A12
C514 R561
L701
J702
R560 C706
J706
R581
U805
C820
R580
C832
R570
R571
R726
C713
R541
R525
C816
C813
R537
R533
R534
C503
C502
L710
R529 1
C516 X201
R528 C410
R551
R531 C409 C408 C407 C406 R712
R403 R404
C818
C819
Q506
R724
R723
R725
C703
U702
Q502
U701
R510
R715
R727
Q505
L802
L804
L401
R511
D708
C249 C224 C223
C235
R512 C242
C511
C270
ZD501
PANNEL
C402
C212 R206
C712
Q501 160
150 C215 C828 R714
D707
LPL
R535
U802
R401
R539 R711
L703
L702
L705
L704
R540
C501
C401
120
R515
C243
R709
C404
C708
C709
R708
C711
C710
R722
R518 R705
C513
Q503
Q701
ZD701
5
C227 C234
L803
R734
U401
C731
C218 C231
R526 R202
C247 C217
C512
BA205
U807
C707
C241 C244
R707
R717
C232
C824
100
ZD702
R524
C226
R501
C802
R538
R503 BA202
C508 C258
C801
R504
C230
C262
L204
R505 R519
90
R506 C259
30
R507 R520
R508
R207
C225
C261
C205
R521 L805
R509 C269
BA201
BA203
C826
C515
R703
C257
C715
L707
40
L706
C504
R720
R522
R813
R204
C254 R208
C250
C202 C208
R701
C204
D701
C256 R209 D706
80
C831
60
R706
70
50
C509
BA204
U201
RA501 RA502
C211
C216
J705
L801
MODEL:LB500K
C717
C220
C271
L205
DATE :2002.07.20
J703
C716
L708
P/N :6870T534A12
ZD1
LED1
SW1
R6
P/N:6870T534C12
R4
DATA:2002.07.20 SW2
ZD2 R1 R2 SW7
- 17 -
EXPLODED VIEW
8
7
11
9
9-1
- 18 -
5
4-B
2-1
2 4-A
10
1
EXPLODED VIEW PARTS LIST
2-1 6304FAU004A LCD(LIQUID CRYSTAL DISPLAY) L150X3M AU TFT COLOR 1024X768 TTL (LB500K-GU)
6634B00051A ADAPTER, AC-DC, PWI1502LG 5V/12A 1A/1A LIPS FOR K-CHASSIS (POWER NET)
6
or 6634B00053A ADATER, AC-DC, ADP-30EP 5V/12A 1A/1A LIPS FOR K-CHASSIS (DELTA)
9 6631T11016C CONNECTOR ASSEMBLY, 20P H-H 100MM UL20276 I/FACE CABLE LB500K (LB500K-GL)
9-1 6631T11011H CONNECTOR ASSEMBLY, 80P H-H 133MM FPC F219-017 LB500J (LB500K-GU)
- 19 -
REPLACEMENT PARTS LIST
CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS,
READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL.
* NOTE : S SAFETY Mark
AL ALTERNATIVE PARTS
- 20 -
DATE: 2002. 7. 24. DATE: 2002. 7. 24.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
TRANSISTOR
C818 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C819 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P Q502 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP S
C820 0CE107CF610 100UF SHL,SD 16V 20% BULK FL Q503 0IKE704200H KIA7042AP TO-92 TP 4.2 VOLT.
C821 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R Q701 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP S
C824 0CH8107F611 100UF 16V M 85STD(CYL) R/TP
C825 0CE107CF610 100UF SHL,SD 16V 20% BULK FL
RESISTORs
C826 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C827 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P R201 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
C828 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R R202 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
C829 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5P R203 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
C831 0CH8107F611 100UF 16V M 85STD(CYL) R/TP R204 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
C832 0CH8107F611 100UF 16V M 85STD(CYL) R/TP R205 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
C835 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R R206 0RJ2701D677 2.7K OHM 1/10 W 5% 1608 R/TP
R207 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R208 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
DIODEs
R209 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
D701 0DS226009AA KDS226 TP KEC SOT-23 80V 300M R210 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
D702 0DS226009AA KDS226 TP KEC SOT-23 80V 300M R401 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
D703 0DS226009AA KDS226 TP KEC SOT-23 80V 300M R403 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
D704 0DS226009AA KDS226 TP KEC SOT-23 80V 300M R404 0RJ5601D477 5.6K OHM 1/10 W 1% 1608 R/TP
D705 0DS226009AA KDS226 TP KEC SOT-23 80V 300M R501 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
D706 0DS226009AA KDS226 TP KEC SOT-23 80V 300M R502 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
D707 0DS301109AA MMBD301LT1 TP MOTOROLA SOT23 3 R503 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
D708 0DS301109AA MMBD301LT1 TP MOTOROLA SOT23 3 R504 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
ZD701 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323 R505 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
ZD702 0DZ560009GB BZT52C5V6S DIODES R/TP SOD323 R506 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R507 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
ICs R508 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R509 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
U201 0IPRPGA002A GMZAN2-160P GENESIS MICROCHIP R510 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
U401 0ITH638300B THC63LVDM83R THINE 56P,TSSOP R R511 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
U501 0IZZTSZ199A MYSON 42PIN BK OTP LB500K R512 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
U502 0ISG240860B M24C08W6 SGS-THOMSON 8SOP R/TP R513 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
U701 0IMO741420B MC74HCT14ADR2 14P,SOIC TP LEVE R515 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
U702 0ICS240213A CAT24WC02J-TE13 8P SOP TP 2K I R516 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
U802 0IPMGKE011A KIA78D33F KEC DPAK R/TP 3.3V L R517 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
U805 0IRH033000A BA033SFP P/MOLD-5 TP REGULATOR R518 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
U806 0IPMGON007A NCP1117ST25T3 ON SEMI SOT223 R R519 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R520 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
COILs & COREs R521 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R522 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
L201 6210TCE001P HB-1S2012-121JT CERATECH 2012M R523 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
L202 6210TCE001P HB-1S2012-121JT CERATECH 2012M R524 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
L203 6210TCE001P HB-1S2012-121JT CERATECH 2012M R525 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
L204 6210TCE001P HB-1S2012-121JT CERATECH 2012M R526 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
L205 6210TCE001P HB-1S2012-121JT CERATECH 2012M R527 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
L401 6210TCE001G HH-1M3216-501 CERATEC 3216MM R R528 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
L701 6210TCE001S HU-1M2012-121 CERATECH 2012MM R529 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
L702 6210TCE001P HB-1S2012-121JT CERATECH 2012M R530 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
L703 6210TCE001P HB-1S2012-121JT CERATECH 2012M R531 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
L704 6210TCE001P HB-1S2012-121JT CERATECH 2012M R532 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
L705 6210TCE001P HB-1S2012-121JT CERATECH 2012M R533 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
L706 6210TCE001P HB-1S2012-121JT CERATECH 2012M R534 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
L707 6210TCE001P HB-1S2012-121JT CERATECH 2012M R535 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
L710 6210TCE001G HH-1M3216-501 CERATEC 3216MM R R536 0RJ1004D677 1000000 OHM 1/10 W 5% 1608 R/T
L801 6210TCE001G HH-1M3216-501 CERATEC 3216MM R R537 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
L802 6210TCE001G HH-1M3216-501 CERATEC 3216MM R R540 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
L803 6210TCE001G HH-1M3216-501 CERATEC 3216MM R R541 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
L804 6210TCE001G HH-1M3216-501 CERATEC 3216MM R R551 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
L805 6210TCE001G HH-1M3216-501 CERATEC 3216MM R R560 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP(LB500K-GU)
R561 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R571 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
- 21 -
DATE: 2002. 7. 24.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
OTHERs
CONTROL BOARD
- 22 -
PIN CONFIGURATION
CAT24WC02J-TE13 8P
BLOCK DIAGRAM
DIP Package(p) SOIX Package(J)
EXTERNAL LOAD
A0 1 8 VCC A0 1 8 VCC
A1 2 7 WP A1 2 7 WP D OUT
SENSE AMPS
SHIFT REGISTERS
A2 3 6 SCL A2 3 6 SCL ACK
V SS 4 5 SDA V SS 4 5 SDA V CC
TSSOP Package(U)
SDA START/STOP
LOGIC
A0 1 8 VCC
A1 2 7 WP
A2 3 6 SCL E 2 PROM
XDEC
V SS 4 5 SDA
WP CONTROL
LOGIC
PIN CONFIGURATION
MC74HCT14ADR2 14P
BLOCK DIAGRAM 1 2
A1 Y1
A1 1 14 VCC
3 4
Y1 2 13 AS A2 Y2
A2 3 12 Y6 A3
5 6
Y3
Y2 4 11 A5
9 8
A4 Y4
A3 5 10 Y5
11 10
Y3 6 9 A4 A5 Y5
GND 7 8 Y4
13 12
A6 Y6
- 23 -
THC63LVDM83R
THC63LVDM83R
1 56
RS TA4
2 55
TD1 TA3
3 54 THC63LVDM83R
TA5 TA2 DATA
4 53
TA6 GND (LVDS)
5 52
GND TA1
- 24 -
SCHEMATIC DIAGRAM
(LG Philips Module)
1. GMZAN2
- 25 -
2. LVDS
- 26 -
3. MICOM
- 27 -
4. DC/DC BLOCK
- 28 -
5. CONNECTOR & JACKS
- 29 -
6. KEY PART
- 30 -
SCHEMATIC DIAGRAM
(AUO Module)
1. GMZAN2
- 31 -
2. LVDS
- 32 -
3. MICOM
- 33 -
4. DC/DC BLOCK
- 34 -
5. CONNECTOR & JACKS
- 35 -
6. KEY PART
- 36 -
Aug. 2002
P/NO : 3828TSL083J Printed in Korea