Professional Documents
Culture Documents
Mainboard 17MB120DS
Mainboard 17MB120DS
Chasis Presentation
APRIL 2016
Phone
USB 3.0 USB 2.0
Head
IR HDMI 1 DP DP IN
DP SPI
HDMI1
OUT
Out
Mboot
SPI
DP
HDMI SPLITTE
HDMI 3
Splitter or DVI
OPS FFC
Nand R IC
IC Mstar Flash
RAM
Connector
Power
RAM
CVBS/YPbPr
RJ12
SUBW LINE (Service
DSUB9
FRC IN Only) or
S/PDIF
LINE LAN RTC
OUT
VGA
(For internal)
BLUETOOTH
JOYSTICK
INTERNAL
SPEAKER
USB D/B
WIFI &
IR LED
USB
Panel TCON
HDCP 2.2 / HDMI1.4 (FHD) input (1 HDMI default, 1 HDMI opt. with DVI, 1 HDMI opt with HDMI 1 Output , 1 HDMI opt. with
OPS)
HDCP 2.2 / HDMI2.0 (UHD) input (1 HDMI default, 1 HDMI opt. with DVI, 1 HDMI opt. with OPS)
1 Displayport1.2a input / 1 DP 1.2a output
1 PC (VGA) input
1 YPbPr / Back S-Video
Line In/ Line out
1 Optic S/PDIF output
1 USB 3.0, 1 USB 2.0 port
1 USB2.0 for touchscreen (optional)
1 OPS interface (optional)
1 Extender IR
1 Dsub9 RS232
1 RJ45 10/100 Support Ethernet
1 RJ12 (for service only)
Tuner ATV/DVB-T/T2/C (optional)
4K2K@ 50/100Hz Vby1, FHD@ 50/100Hz LVDS interface
4
Power socket is used for taking voltages which are 12V, 5V and VDD_Audio.
These voltages are produced in power board.
Also socket is used for giving dimming, backlight and standby signals with power board.
Possible causes: Backlight pin, dimming pin, backlight supply, stby on/off pin
BACKLIGHT_ON/OFF pin should be high when the backlight is ON. R89 must be low when the backlight is OFF. If it is a problem,
please check Q10 and the panel cables. Also it can be tested in TP137 on main board
0V or +3.3V
0V or +3.3V
≈+3.3V
+12V
+12V
10
0V
11
+12V
+3.3V
+1V
+24V
+1.8V
+3.3V
+1V
+1.5V
12
+3.3V
13
+3.3V
14
+5V
+5V
+5V +5V
15
+3.3V
+24V
+24V
+3.3V
16
+3.3V
<+2.9V
17
0V
≈200ms
+12V
18
HBB - 2016
19
2017
You can control the product from an external PC via RS-232 (COM port) or LAN
(Ethernet port) on the PC.
For instance, system source can be changed by RS-232 from remote computer. When a
command is sent from the PC to the product, the product operates according to the
received command and sends a response message to the PC.
In general, the RS-232 commands are sent for operating the implemented functions
via serial port and utility. A suitable utility can be used such as described below.
Download and install the PuTTY software from the following link first:
http://www.putty.org/.
Run the software and enter the Display’s IP address in the field Host Name.
Enter “1986” as a default value in the field Port. Then select “Telnet” as Connection
type and click the Open button.
Note: Refer to the Connectivity section of this manual for information on connecting the
Display to a network and displaying the IP address of the Display.
4
Use the commands in the RS232 Command Table. For example, if “GETVOLUME”
command is entered, current volume level should be displayed on the putty window as
shown in the pictures below.
Another example;
When “GETSOURCE” command is entered, current source should be displayed on the
putty window as shown in the picture below.
Run the software and select Serial as Connection Type. Enter the Display’s serial port in
the field Serial Line (in the following example it is COM4) and “115200” in the field
Speed. Then click the Open button.
Enables/disables remote control string-integer n (n = ON, n set remote state On or set remote state OFF
SETRC
commands. = OFF)
string-integer n (n = 0, n = 1,
KEY Send key to Eclipse. ......, n = up, ......, n = menu, n key send to Eclipse
.....ext.)
You may observe prints Bank 0, Bank 1 etc. Be sure or observe debug print outs: "MFC
ISP: done" will be writen... This may take over
USBOPERATIONS Perform USB Operations no parameter 10 minutes.
integer n (5=FAV,
Select source. (0=TV, other source indexes(some of them 7=HDMI1, 8=HDMI2, " #*select TV source or
are not enabled))
SELECTSOURCE 11=YPbPr, 12=Vga, #*select External source …"
18=DVI , 19=DP ,
20=OPS)
"#*standby off or
GETSTANDBY Get standby on/off. no parameter #*standby on"
You may observe prints Bank 0, Bank 1 etc. Be sure or observe debug print outs: "MFC ISP: done" will
be writen... This may take over
USBOPERATIONS Perform USB Operations no parameter 10 minutes.
#*setDigitalOut() set to n OR
SETDIGITALOUT Set digital out. string n (compressed, pcm) #*Incorrect digital out mode
parameter entered
10
Set static IP address of eth0 network str-int n Example: set_IP_ "#*IP address setting Succesfull
set_IP_address
interface. address 192.168.0.15 #*IP address setting NOK"
Get IP address of eth0 network interface.
get_IP_address Usage: get_IP_address no parameter #*IPaddr: ...
12
VGA/PC COMMANDS
Command Description Parameter Return
13
GETCOLOUR Get picture colour value. no parameter #*THE COLOUR VALUE : ...
"#*Picture colour value is set to n
#*Same value is set. Do nothing.
SETCOLOUR Set picture colour value. int n (0 ≤ n ≤ 100)
#*Incorrect value must between
defined ranges 0-100"
"#*Picture skin tone value is set to n
#*Same value is set. Do nothing.
Set picture skin tone value.
SETSKINTONE int n (-5 ≤ n ≤ 5) #*Incorrect value must between
defined ranges -5-5"
str-int type, value (type = redgain, "#*White Balance is set to value Invalid value for White Balance (0-
greengain, bluegain, redoffset, 255)
SETWB Set white balance value.
greenoffset, blueoffset) (0 ≤ value ≤250) Invalid type for White Balance"
14
"seMonitorirtual3D() set
int n (0 = off, 1 = low, 2 = to n Incorrect virtual 3d
SETVIRTUAL3D Set virtual 3d values.
medium, 3 = high) mode paramater entered
"
Inrease Contrast Level by 1 step
CONTRASTUP no parameter Picture contrast value is set to …
15
16
set view style (Flat or #*The view style is set to ... (Flat or Folder)
SETVIEWSTYLE string n (Flat, Folder)
Folder)
get view style (Flat or #*The view style is ... (Flat or
GETVIEWSTYLE no parameter
Folder) Folder)
integer n ( 5, 10, 15, 20, #*The slideshow interval is set to
SETSLIDESHOWINTERVAL set slide show interval
25, 30 ) ... seconds
#*The slideshow interval is ... seconds
GETSLIDESHOWINTERVAL get slide show interval no parameter
17
18
19
1. RJ12 is connected to UART 0, DSUB9 is connected to UART 1. Therefore, UART 0 and UART 1 could
be tested separately in this type of the board
2. RJ12 and DSUB9 both are connected to UART 0. UART 1 is supported for OPS module but not
reachable. Therefore, only UART 0 could be tested in this type of the board.
• Open any serial port communications program (e.g Realterm). Configure serial communication settings as
below:
Baud Rate : 19200 for UART0, 9600 for UART1
Parity : None
Data Bits :8
Stop Bits :1
Handshake : None
Note that UART0 default value: ASCII, UART1 default value: HEX In the tables given below, XY represents are variable byte.
All byte values are hexadecimal.
Error Responses
• NAK reply: 15 When the display cannot understand the received command, it returns this value. In such a case, check
the sending code and send the same command again.
• Error reply: 1C 00 00 When the display cannot execute the received command for any reasons, it returns this value. In such a
case, check the sending code and the setting status of the display. 20
Packet
Header Data CRC Setting 0 1 2 Notes
Action Type
code Size flag code
Name Operation L H L H L H L H L H L H
ON BE EF 03 06 00 19 D3 02 00 00 60 02 00 06
Monitor OFF BE EF 03 06 00 19 D3 02 00 00 60 01 00 06
XY can be either 00 or 01. 00
GET BE EF 03 06 00 19 D8 03 00 00 60 07 00 1D 00 XY
means OFF, 01 means ON.
ON BE EF 03 06 00 D6 D2 01 00 02 20 01 00 06
Mute
OFF BE EF 03 06 00 46 D3 01 00 02 20 00 00 06
XY can be either 00 or 01. 00
GET BE EF 03 06 00 75 D3 02 00 02 20 00 00 1D 00 XY
means OFF, 01 means ON.
ON BE EF 03 06 00 6B D9 01 00 20 30 01 00 06
Screen
OFF BE EF 03 06 00 FB D8 01 00 20 30 00 00 06
XY can be either 00 or 01. 00
GET BE EF 03 06 00 C8 D8 02 00 20 30 00 00 1D 00 XY
means OFF, 01 means ON.
OPS BE EF 03 06 00 FE D2 01 00 00 20 00 00 06
HDMI BE EF 03 06 00 0E D2 01 00 00 20 03 00 06
Source
VGA BE EF 03 06 00 6E D2 01 00 00 20 01 00 06
SCART2(CVBS) BE EF 03 06 00 00 00 01 00 00 20 04 00 06
FAV BE EF 03 06 00 00 00 01 00 00 20 05 00 06
S-Video BE EF 03 06 00 00 00 01 00 00 20 06 00 06
HDMI2 BE EF 03 06 00 00 00 01 00 00 20 08 00 06
HDMI3 BE EF 03 06 00 00 00 01 00 00 20 09 00 06
HDMI4 BE EF 03 06 00 00 00 01 00 00 20 0A 00 06
YPbPr BE EF 03 06 00 00 00 01 00 00 20 0B 00 06
SCART2 BE EF 03 06 00 00 00 01 00 00 20 0D 00 06
(S-Video)
TV BE EF 03 06 00 00 00 01 00 00 20 0E 00 06
SCART1(CVBS) BE EF 03 06 00 00 00 01 00 00 20 0F 00 06
SCART1
BE EF 03 06 00 00 00 01 00 00 20 10 00 06
(S-Video)
DVD BE EF 03 06 00 00 00 01 00 00 20 11 00 06
Source
DVI BE EF 03 06 00 00 00 01 00 00 20 12 00 06
DP BE EF 03 06 00 00 00 01 00 00 20 13 00 06
WIDI BE EF 03 06 00 00 00 01 00 00 20 15 00 06
XY can be one of the following:
01: OPS, 02: HDMI, 03: VGA,
04: SCART2(CVBS), 05: FAV,
06: S-Video, 08: HDMI2, 09: HDMI3, 0A: HDMI4, 0B: YPbPr,
0D: SCART2(S-Video), 0E: TV, 0F: SCART1(CVBS), 10: SCART1(S-
GET BE EF 03 06 00 CD D2 02 00 00 20 00 00 1D 00 XY Video), 11: DVD,
12: DVI, 13: DP, 15: WIDI
Note that all of the sources are not enabled.
GET BE EF 03 06 00 31 D3 02 00 01 20 00 00 1D 00 XY
Volume
INCREMENT BE EF 03 06 00 57 D3 04 00 01 20 00 00 06
DECREMENT BE EF 03 06 00 86 D2 05 00 01 20 00 00 06
XY can take 00 as a minimum and 1D as a maximum.
SET BE EF 03 06 00 31 D3 03 00 01 20 01 XY 06
21
HBB - 2017
22
APRIL 2017
UNB Series
eXNB Series
VW55X501 VW55X701
49" (450 Nits 3.8 mm) 55" (500 Nits 1.8 mm) 55" (700 Nits 1.8 mm) 55" (500Nits 3.8 mm) 55" (700Nits 3.8 mm)
Backlight Type DLED DLED DLED DLED DLED
Panel Technology IPS IPS IPS IPS IPS
Panel Type 24/7 DID Panel 24/7 DID Panel 24/7 DID Panel 24/7 DID Panel 24/7 DID Panel
Front Type Ultra narrow bezel Extra narrow bezel Extra narrow bezel Ultra narrow bezel Ultra narrow bezel
Orientation Horizontal / Vertical Horizontal / Vertical Horizontal / Vertical Horizontal / Vertical Horizontal / Vertical
Resolution 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080
Brightness 450 cd/m2 500 cd/m2 700 cd/m2 500 cd/m2 700 cd/m2
Contrast Ratio 1300 : 1 1400 : 1 1400 : 1 1400 : 1 1400 : 1
Dynamic Contrast
360000 : 1 400000 : 1 560000:1 400000 : 1 560000:1
Ratio
Panel life time
(Typ.)(LED Life Time) 60000hrs 60000hrs 60000hrs 60000hrs 60000hrs
Size 1077.6 (L) × 607.8 (H) 1211.4 (L) x 682.2 (H) 1211.4 (L) x 682.2 (H) 1213.4(H) x 684.2(V) 1213.4(H) x 684.2(V)
× 94.2 mm (D) x 53.3(D) x 53.3(D) x 97.6mm(D) x 97.6mm(D)
1196 (H) x 729 (V) x 1359(H) x 804(V) x 1359(H) x 804(V) x 1359(H) x 804(V) x 1359(H) x 804(V) x
Shipping Size (1 Unit)
209 (D) 209(D) 209(D) 209(D) 209(D)
Panel Weights 27.5 kg 29.4 kg 30.3 kg 30.1 kg 29.5 kg
Shipping Weight (1
Unit) 30.5 kg 32.4 kg 33.3 kg 33.1 kg 32.5 kg
Shipping Weight (4
Unit) 131 kg 138 kg 143 kg 142 kg 139 kg
Bezel Width 3.8 mm 1.8 mm 1.8 mm 3.8 mm 3.8 mm
Working Conditions
Temperature
+50°C / 0°C +50°C / 0°C +50°C / 0°C +50°C / 0°C +50°C / 0°C
Conditions
Humidity 90% 90% 90% 90% 90%
General Features
Keyboard N/A N/A N/A N/A N/A
Speaker N/A N/A N/A N/A N/A
Joystick Button þ þ þ þ þ
RTC Clock þ þ þ þ þ
Failure Feedback No No No No No
Brightness Sensor No No No No No
Power
Power Supply 110 VAC - 240 VAC 110 VAC - 240 VAC 110 VAC - 240 VAC 110 VAC - 240 VAC 110 VAC - 240 VAC
Power
Consumption(Deep
StandBy) TBD TBD TBD TBD TBD
Power
Consumption(On Full
Load) 110W 195W 250W 186W 308W
5
MD.ASY.17TS12-VIDEOWALL_MATRIX BOX
10
11
12
13
Daisy Chain
14
15
Set ID:
Product ID in the system. It is used in RS232 communication and
communication with the product is performed by using this ID if any
product in the system is to be commanded.
Serial Number:
The serial number of the product which is written in production line.
Model Name:
Model name of the product which is written in production line.
16
17
18
20
•No Backlight
220V cabling, mains and 220V input socket must be checked.
Panels should be checked for Standby status.
Power card should be checked.
21
If the image transmission is via DP, the DP cables and sockets must
be checked.
DP Firmware version should be checked in service menu.
If «N/A» , this means fw is not loaded.
The technical specifications of the device used as video source for
image transfer via DP are important. For example, if the image is
transferred with a source with HDCP key protocol, DP daisy chain can
be applied up to 7 units. Without the HDCP key protocol, it may also be
related to the transfer limit of the PC's graphics card.
22
HBB - 2017
23