Professional Documents
Culture Documents
Caution: Ensure that the floor and sub-floor can support the
Receiving & Unpacking Product
Weight Height Width Depth
total weight of the system, especially when the weight is
concentrated on the stabilizing feet.
(kg/lb) (mm/in) (mm/in) (mm/in)
Symmetra® PX 48 kW
Symmetra PX 48 kW System (SYCF48KH) Caution: Ensure that the floor is level. The enclosure cannot
and Packaged be installed on a floor that is not level.
® PX 160 kW UPS Systems 331/729 2140/84 848/33.3 1210/47.6
Symmetra
Unpackaged 307/679 2011/79.1 600/23.6 1070/42.1
Symmetra PX 160 kW UPS (SYCF160KH) Use a pallet jack or a forklift to move the pallets to the
installation site.
Packaged 358/789 2140/84 848/33.3 1210/47.6
Unpackaged 325/716 2011/79.1 600/23.6 1070/42.1 Space Considerations
XR Battery Enclosure (SYCFXR9 and SYCFXR48) Symmetra PX 48 kW system.
Packaged 379/835 2150/84.6 848/33.3 1210/47.6
Unpackaged 345/760 1996/78.5 600/23.6 1070/42.1
Front-to-rear
airflow
PDU-XR (PDUM160H-B) Floor-to-ceiling
ventilation:
Packaged 444/978 2150/84.6 848/33.3 1210/47.6 2200 mm 600 mm
Unpackaged 411/904 2004/78.8 600/23.6 1070/42.1 (86.6 in) (23.6 in) Minimum
rear
Battery unit (SYBTU2-PLP) clearance:
Packaged 27/59.2 180/7 150/5.9 810/31.89 Enclosure 150 mm
Unpackaged 25.2/55.3 159/6.2 107/4.2 700/27.5 (6 in)
1070 mm
Power module (SYPM10K16H) Minimum (42.1 in)
front clearance:
Packaged 31.5/69.5 225/8.8 595/23.4 795/31.3 600 mm 1000 mm
IMPORTANT SAFETY INSTRUCTIONS Unpackaged 28.5/62.8 132/5.2 483/19 700/27.5 (23.6 in) (39.4 in)
SAVE THESE INSTRUCTIONS
Symbols used
Receiving Symmetra PX 160 kW system.
990-3013A-001
*990-3013A-001* 01/2008
Unpacking Caution: The enclosures are on casters. Take precautions to
Note: Stored batteries should be recharged at regular
intervals, depending on the storage temperature. Refer to the
prevent it from rolling off the side of the pallet. Battery Module Storage and Replacement sheet (990-2958) for
How to unpack the enclosures more information.
Align the hook-and-loop tape strips
Note: If the system is not being installed immediately, do not on the ramp to the tape strips on the
remove the packaging. Store the system in an indoor, pallet.
temperature-controlled area, free of conductive contaminants.
Documentation Storage
48 kW system
Cut the plastic wrap along the edges.
Use two people to roll the enclosure
off the pallet and guide it down the
ramp.
Remove the
plastic wrap
and cardboard
covers. Remove
the ramp and
set it aside.
160 kW system
Note: After the unit has been removed from the pallet, move
it only by rolling it on the casters.
Remove the stabilizing brackets from
the front and back of the enclosures.
Please Recycle
The shipping materials are recyclable. Save them for later use,
or dispose of them appropriately.
Storage Conditions
Contact Information
For local, country-specific centers: go to www.apc.com/support/contact
or see the back cover of the operation manual for phone numbers.